fo-55112-c 4 honeywell part number size drawing name sheet c title scale drawn check pro/engineer rev this drawing covers a proprietary item and is the property of honeywell. this drawing is not to be copied or used without the permission of honeywell. tolerances unless noted: a 3 2 1 b c d 4 3 2 1 a b c d type cage_code ( ) .018 .60 .040 .05 .110 .392 .72 .078 .56 approx pullout to change position .090 total travel 34 $ # 8 $ 17 $ # 4 $ .42 1.05 .47 1.10 min .13 min .13 .24 .427 1.340 max .28 .75 .38 .26 .38 .910 max 1.35 .250 military standard number catalog listing available locking combinations for configuration see lettered details circuit made with toggle lever in military rating (amps) keyway side (1-2, 4-5) center (1-2, 4-5) opposite keyway (2-3, 5-6) resistive load lamp load inductive load dc volts ac volts 28 125 250 125 250 28 vdc 125 vac 28 vdc 125 vac 24659-21 2tl1-1 a,b,d,e,f,g,h, j,k,l,m,n,p on off on 20 .75 .5 15 6 7 4 15 15 24659-22 2tl1-2 d,f,g off none on 24659-23 2tl1-3 d,f,g on none on 24659-24 2tl1-21 e,f,k,m none off on 24659-33 2tl1-31 e,f,k,m none on on 24659-29 2tl1-4 f mom off none on 18 .75 .5 11 6 5 2 10 8 24659-31 2tl1-5 e,f,k,l,m,n mom on off on 24659-30 2tl1-6 f mom on none off 24659-27 2tl1-7 e,l,n mom on off mom on 24659-26 2tl1-8 f mom on none on 24659-32 2tl1-51 e none on mom on 24659-28 2tl1-61 e mom on off none see chart rev document changed by check 33 0056412 sjk 10sep09 cmh redrawn without change in pro-e design units: inch interpret per asme y14.5m-1994 other honeywell engineering standards may apply 3d switch - toggle lsd 29jun77 gch 07jul77 1 of 1 2:1 i - 2tl1 series chart 2 33 15a-125, 250 or 277 vac 1/2 hp-125vac; 1hp- 250 , 277vac 5a-125vac "l" code l191 10a-125, 250 or 277 vac 1/4hp-125vac; 1/2hp- 250 , 277vac 3a-125vac "l" code l192 weight: .15 lb, approx notes: 1 - switches are capable of withstanding a temperature of 160 $ f continuously at full rated load. 2 - circuit designation, micro switch catalog listing and "ms" number marked on side of switch. 3 - furnished unassembled. 4 - for terminal cover, see micro switch catalog listing 5pa8. 5 - keyway shown on left side. 6 - suffix letter must be added for desired type of toggle locking. see chart for available locking combinations. 7 - applies only to "on" and "momentary on" positions. 8 - these switches are qualified under mil-s-3950. 9 - from bottom of keyway to major dia. of 15/32 thread. (refer to l191 for ul rating) (refer to l192 for ul rating) lockwasher locking ring hex nut (2) "a" locked in three positions "b" locked in center and extreme position (keyway side) "d" locked out of center position "e" locked in center position "g" locked in extreme position (keyway side) "h" locked out of center and extreme position (keyway side) "j" locked out of center and extreme position (opposite keyway) "f" locked in extreme position (opposite keyway) "k" locked in center and extreme position (opposite keyway) "l" locked out of extreme position (keyway side) "p" locked out of and into extreme position (keyway side) "m" locked out of and into extreme position (opposite keyway) "n" locked out of extreme position (opposite keyway) see locking details for description ("a" locking insert shown) sealed to prevent entrance of liquids or dust 15/32-32 uns-2 thread to within .060 of shoulder 6-32 unc x .260 ref binding head terminal screw and lockwasher (sems) one per terminal .076 # .008 wide keyway third angle projection no places x one place .x two place .xx three place .xxx angles x - .03 .015 .005 - # # # # # 6 6 7 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5 5 3 9
|
