View MPD7D067S_7287470.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 1 dc-dc converter specification(draft) mpd7d06 * s 1 . application this specification applies to dc-dc converte r mpd7d06*s(*:7,8) for telecommunication / data-communication equipment. for any other application, please c ontact us before using this product. 2 . customer reference customer spec. number customer part number 3 . customer & murata part number nominal output voltage customer part number part number 3.3v MPD7D067S 5.0v mpd7d068s
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 2 4 . appearance, dimensions objective products mpd6d11*s (* 1,2,3,4,6,7,8,9) marking (1) mfg id (2) lot no. ?? production factory mark production year production month 1,2,3, 9,o,n,d (3) product number ?? part number of underlined mpd7d06* s . (in mm) 3 4 5 6 p p p p p p p p p 2 mark of pin no.1 19 18 17 16 15 14 13 12 mpd 6d? (4p) 37.30.5 3.600.5 (3.60) 39.90.6 8.0max 10 30.05+1.1-0.5 p=2.540.2 tolerance is not accumulated coplanarity max.0.1 unit : mm cus 1 11 20 mpd7d s 1 2 3 4 5 6 min0.08 1.30.3 0~10 0.5 +0.1 -0.15 lead in detail
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 3 drive +vin po rc alm control ic -vin +vout -vout 17 4 3 2 12 13 14 drive filter 16 18 19 6 5 5 . pin number and function pin no pin symbol function 1,10, 11,20 nco mechanical supplemental contact pins. pins at the four corners on printed circuit board. to contact dc-dc converter mounted board with thermal setting resin. 2 +vout (+)output 3 +vout (+)output 4 +vout (+)output 5 -vout ( - )output 6 -vout ( - )output 12 alm alarm output 13 rc remote on/off control 14 po parallel operation 15 nc - 16 +vin ( + )input 17 +vin ( + )input 18 -vin ( - )input 19 -vin ( - )input 6. block diagram 6.1 entire product
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 4 7. environmental conditions 7 .1 operating temperature range -40c ~ +85c (with power derated.) 7 .2 operating humidity range 20% ~ 85% -40~ +85c no water condenses. 20% ~ 95% -40~ +75c no water condenses. 7 .3 storage temperature range -45c ~ +90c 7 .4 storage humidity range 10% ~ 95%( no water condenses.) 8. absolute rating item unit absolute rating remarks minimum input voltage v 0 continuous v 75 maximum input voltage alm applied voltagerc applied voltage time 200s v 90 slew rate 42v/10s po applied voltage v 8 maximum alm sink current ma 10 no voltage, no matter how instantaneous, shall be appli ed beyond the absolute maximum voltage rating to this product. if you apply any voltage over this limit, the product characte ristics will deteriorate or the product itself will be destroyed. even though it may continue operating for a while after the over-voltage event, its life will likely be shortened significantly. reliability and life of the module may degrade similarly if the maximum operating voltage rating is continuously exceeded. this product is designed to operate with in the maximum operating voltage rating specification. 9. characteristics 9 .1 electrical characteristics (ta=25c) 9 .1 .1 general characteristics unless otherwise specified, (ta= -40 to +85c with power derated.) value item symbol condition min. typ. max. unit input voltage range vin 36 48 75 v turn-on input voltage vin=increasing 32 - 36 v input voltage difference of turn-on and turn-off po pin : open or connected to po pin of other dc-dc converters 2.0 - - v galvanic isolation voltage input time : 1 minute 1500 - - vdc item standard note noise (radiation, conduction) in accordance with vcci class a refer to test circuit in clause 10 recognized ul60950(ul/c-ul), complied iec 60950 ul file no.e190503 safety standard(note 1) ce marking ce mark is shown on a package box. note 1: 2a of input current limitation is necessary to apply to the safety standard. it is recommended that a fuse or current limitation circui try is connected to the input of dc-dc converter. individual input of dc-dc converters should be limited for the applicat ion of parallel and/or multiple operation.
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 5 9 .1 .2 specific characteristics (ta= - 40 to +85c with power derated.) part number MPD7D067S value item symbol condition min. typ. max. unit nominal output voltage vo - 3.3 - v output voltage variation regtot vin=36 to 75v, io=0 to 10.6 ta=-40 to +85c -3 +5 % output current io power derated. 0 - 10.6 a efficiency at rated vin, io, ta=25c - 91 - % ripple voltage - - 50 ripple voltage & noise vr refer to test circuit - - 100 mvpp over current protection iocp 10.9 - - a over voltage protection vovp output halts in latch-up mode after mask time 0.5msec (typ) to avoid malfunction by noise and transient change. input turn off and on to reset. 3.96 - - v low voltage protection vlvp output halts in latch-up mode after mask time 500msec (typ) to avoid malfunction by noise and transient change. input turn off and on to reset. - - 2.97 v part number mpd7d068s value item symbol condition min. typ. max. unit nominal output voltage vo - 5.0 - v output voltage variation regtot vin=36 to 75v, io=0 to 9 ta=-40 to +85c -3 +5 % output current io power derated. 0 - 7 a efficiency at rated vin, io, ta=25c - 92 - % ripple voltage - - 50 ripple voltage & noise vr refer to test circuit - - 100 mvpp over current protection iocp 7.2 - - a over voltage protection vovp output halts in latch-up mode after mask time 0.5msec (typ) to avoid malfunction by noise and transient change. input turn off and on to reset. 6 - - v low voltage protection vlvp output halts in latch-up mode after mask time 500msec (typ) to avoid malfunction by noise and transient change. input turn off and on to reset. - - 4.5 v the above electrical characteristics are guaranteed in t he condition that the impedance of the input power supply is sufficiently low as shown in clause 10. connecting an input inductance or using an input power supply with output inductance may cause an unstable operation of this product. please check the proper operati on of this product with the peripheral circuits on your product.
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 6 9-1-3-1 .typical power derating MPD7D067S 1pcs operation use we would like to emphasize t hat these data are based on our experimental measurement. for parallel operation, please equalize line impedance from each of dc-dc converters. natural air condition 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient tem p erature ( c power deratin g( % ) forced air condition:0.8m/s 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient temperature ( c power deratin g( % ) forced air condition:1.2m/s 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient tem p erature ( c power deratin g( % )
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 7 9.1.3.2 typical power derating mpd7d068s 1pcs operation use we would like to emphasize that these data are based on our experimental measurement. for parallel operation, please equal ize line impedance from each of dc-dc converters. natural air condition 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient tem p erature ( c power deratin g( % ) forced air condition:0.8m/s 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient tem p erature ( c power deratin g( % ) forced air condition:1.2m/s 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 a mbient tem p erature ( c power deratin g( % )
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 8 9-2. operation information 9-2-1. reset condition in order to reset all function , the input voltage (vin) is set under 5v for 1s. min. 9-2-2. over voltage protection (ovp) the isolated dc-dc converter becom e into latch-up mode after typical 0.5ms. mask time,when the output voltage is over the value s pecified in over voltage protection( 8.1.2) by failure of internal control circuit. in order to reset, the input voltage is set under 5v for 1s. mi n. output voltage might exceed the point at which ovp starts to function under the s pecific condition of transient input voltage or output current change. therefore,ovp is set to wait for the mask time 0.5ms. it is recommended to evaluate your appliances installed with the dc-dc converter. 9-2-3. low voltage protection (lvp) the isolated dc-dc converter becomes into latch- up mode after typical 500ms. mask time,when the output voltage is under the va lue specified in low voltage protection(8.1.2) by operating over current-limit inception due to failu re of internal control or over load. in order to reset, the input voltage is set under 5v for 1s. min. 9-2-4. remote on/off control the connection to a rc pin controls an isolated dc-dc converter to turn on/off. while the isolated dc-dc converter is halted under the remote control, alarm function does not operate;refer to alarm output. start : rc is open or connected to -vin halt : rc is connected to +vin 9-2-5. alarm output (alm) alm pin is down to the same voltage level of-vin pi n and sends an alarm signal. (open-drain output) sink current in alm pin is max.10ma. it is possible to halt all of the connected dc-dc converters when any one is halted with over voltage protection or low voltage protection, with connecting all alm pins for the application of parallel/ multiple operation (note 1) with plural dc-dc converters. the maximum number connecting dc-dc converters is 5pcs of paralle l operation,10pcs of multiple operation ,for the purpose of halting all dc-dc converters connected with al m pin each other. please contac t us when more than these figures. note 2 the parallel operati on of this series is limited to only the same model. vin 36 to 75v reset condition 5v min 1s.min vin 36 to 75v re-s t art condition 5v min 1s.min vin 36 to 75v re-start condition 5v min 1s.min
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 9 9-2-6.synchronous turn-on/off it is possible to avoid the unevenness of turn -on timing with unifying the vari ous turn-on input voltage to a certain voltage which one dc-dc converte r has, and with connecting po pins each other for the application of parallel/mu ltiple operation (note 2) of plural dc-dc converters. it is nec essary to connect po pins for parallel operation. the maxi mum number connecting dc-dc conver ters is 5pcs of parallel operation, 10pcs of multiple operation, for the purpose of synchronous turn -on/off with connecting po pins. please contact us when more than these figures. note 2 the parallel operation of this se ries is limited to only the same model. 9. 3 reliability 9. 3. 1 reliability test items. item test condition criteria high temperature +85 c 1000hours low temperature -40 c 1000hours humidity +65 c 95%rh 1000hours thermal shock -40 c ? +85 c 300cycles operation in high temperature and humidity +85 c 85%rh 1000hour at rated input voltage and normal output current. mechanical vibration 10 to 55hz, max. 1.5mm amplitude, 1 hour for each of x, y, z directions. mechanical shock 20g, 1 time for each of x, y, z directions. no damage in appearance and no deviation of electrical characteristics before and after the test. 9.3.2. soldering heat resistance immerse the part of lead where it is to be soldered on a motherboard in a solder bath of 260+/-5c for 3+/-0.5s. then tested products are left for 2 hours. there is no damage in appearance and no deviation from electrical characteristics in clause 9. 9.3.3. lead pin strength strain a lead pin by gradual-increasingly 5.0n along axial direction; withstand for 5s. no damage on a lead pin. 9.3.4. solderability of leads the lead pins will be immersed in t he isopropyl alcohol (jis k 1522) with rosin (jis k5902) solution (the concentration of rosin will be allow ed 10wt% to 35wt%, and normally approx. 25wt% will be used without any specific requirement.). then the lead pins will be immersed in the solder h 63a (jis z 3282) solution at the temperature of 230c +/-5c for 3+/-0.5seconds, and pulled up completely. the solder will adhere to over 75% of immersed area.
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 10 10. measure construction 10-1.standard test circuit 10.1.1 output ripple & noise isolated dc-dc converte r v ein a ein : stabilized dc power supply : multimete r rl : electronic or resistive load v a oscilloscope v a rl +in +out -in -out ein oscilloscope f bw :500mhz coaxial cable:1.5d-2v(refer to jis c3501) ,1.5m length feedthru- termination trc-50f by keisoku giken equivalent schematic r : 50 c : 0.01 f c=10 f ceramic capacitor ceramic capacitor :10 f (connected output pins) coaxial cable in out b a a : output ripple & noise b: output ripple c: switching period c
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 11 10.1.2. radiation noise 10.1.3. conduction noise (note) measurement at radiation noise, conductive noise, out put ripple & noise. please measure radiation noise, conductive noise and output rippl e & noise with conforming to the test circuit in clause 10 otherwise the noise might not meet the spec ified values. clamper isolated dc-dc converter resistive load zcat3035-1330(tdk), 7 pcs in series lisn isolated dc-dc converter resistive load knw-407 kyoritsu corporation
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 12 11. packaging information 11.1 tray dimensions dc-dc converters are put in the trays. fig.1 200.0 300.0 41.25 b' 46.0 43.5 06ps 43.5 43.5 43.5 43.5 6ps 0076 54.0 54.0 b b' a a'
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 13 11-2. contained pieces of products per corrugated box. maximum contained products pieces 72 pcs/corrugated box. further plural sheets of corrugated cardboa rd are placed on the top of the dummy tray according to number of contained trays in order to full up the space in a corrugated box. 11-3. packaging form trays with products are lidded and packed in a corrugated box. (see fig.2) trays containing products bottom sheet of corrugated cardboard dummy tray fig.2 corrugated cardboard box label marking on the box : part number, : quantity, : inspection number, : ce marking. dimension [unite : mm] of corrugated box is reference only.
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 14 12. production factory komatsu murata mfg.co.,ltd. kanazu murata mfg.co.,ltd. wakura murata mfg.co.,ltd. caution 1 . be sure to provide an appropriate fail-safe function on your product to prevent secondary damage that may be caused by the functional trouble or the failure of this product. 2. please contact us be fore using this product for the applications listed below which require especially high reliability for the prevention of def ects and failure , which might direct ly cause damage to the third party?s life, body or property. aircraft equipment aerospace equipment undersea equipment power plant control equipment medical equipment transportation equipment (vehicles, trains, ships, etc.) traffic signal equipment disaster prevention /crime prevention equipment any other application of similar complexity and/or reliability requirements to the applications listed above. ! note 1. please make sure that the eval uation and testing are completed with this product actually assembled on your product. 2. all the items and parameters in this product spec ification have been prescri bed on the premise that our product is used for the purpose, under the c ondition and in the environment mutually agreed upon. please do not to use this product deviating from such agreement. 3. we consider it not appropriate to include other terms and conditions for trans action warranty in product specifications, drawings or ot her technical documents. therefore, if your technical documents include such terms and conditions as warrant y clause, product liability clause, or inte llectual property infringement liability clause, we will not be able to accept such term s and conditions unless they are based on the governmental regulation or they are stat ed in a separate contract agreement. !
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 15 13. notice 13.1. soldering 13.1. 1. flux please solder this product with rosin flux, wh ich contains of 0.2wt% . or less chlorine. please do not use high activity acid flux or water soluble flux because they may erode metal or glass portion of this product and may cause defectiveness or deterio ration of this product. 13.1.2. solder please use the solder h60, h63( jis z3282)or the equivalent type. please use the solder paste of equivalent type h60, h63. 13.1.3. recommended soldering conditions reflow solder reflow soldering profiles jedec ipc/jede j-std-020c table 5-2 classification reflow profiles pb-free assembly large body profile details soldering temperature 245 oc +0/-5 soldering time 20 40 seconds,240 245 oc heating time 60 150 seconds,217 oc or more. preheating time 60 180seconds,150 200 oc programming rate 3 oc /sec.max.,217 245 oc descending rate 6 oc /sec.max. total soldering time 8 minutes max.,25 245 oc time 1times the solder used to this product is melted in reflow process. therefore do not add excessive vibrati on and strong air below to this product during reflow. please take out the products from a reflow fu rnace after the product te mperature is cooled down thoroughly. please do not mount isolated dc-dc converter on backside of a motherboard like the below figure due to the possibility to drop the is olated dc-dc converter duri ng reflow process. 13.2. cleaning 13.2.1. please clean this product to remove flux by using dip, boil, and vapor methods in isopropyl alcohol for up to 5 minutes. please inform us if you are to use aqueous or semi ?aqueous cleaning or other methods. do not use ultrasonic cleaning because semicon ductor device on this product maybe damaged by resonance. 13.2.2. after cleaning, pl ease dry this product thoroughly. if you touch the wet product, marking maybe erased or blurred. do not measure electrical characteristics, until this product gets dried enough. 13.2.3. if you don?t clean this product with no-cleaning type flux, you must conf irm fully in advance the reliability of this product. isolated dc-dc converter motherboard
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 16 13.3. storage 13.3.1. please store the products in room where the temperature/humidit y is stable and direct s unlight cannot come in, and use the products within 6 months after delivery. please avoid damp and heat or such places where the temperature greatly changes, as water may condense on this product, and the qua lity of characteristics may be r educed, and/or be the solderability may be degraded. if this product needs to be stored for a long time (more than 1 year), this product may be degraded in solderability and/or corroded. please test the solderability of this product regularly. baking before reflow process is unnecessary to st ore the products under 30,60%rh or less up to 6 months. if the storage condition is over above mentioned, recommend a baking at 1005,24 hours before reflow process. 13.3.2. please do not store this produc t in the conditions such as a dusty plac e, a place exposed directly to sea breeze, or in an atmosphere c ontaining corrosive gas (cl2, nh3, so2, nox and so on). 13.4. operational environm ent and operational conditions 13.4.1. operational environment this product is not water-, chemical- or corrosion-proof. in order to prevent leakage of el ectricity and abnormal temperature rise of this product, do not use this product in the following conditions: (1) in an atmosphere containing corrosive gas (cl2, nh3, so2, nox and so on) (2) in a dusty place (3) in a place exposed to direct sunlight (4) in such a place where water splashes or in such a humid place where water condenses (5) in a place exposed to sea breeze (6) in any other places similar to the above 13.4.2. operational conditions please use this product within s pecified values (power supply, temperature, input, output, load condition, and so on). if not used within the specified values, defectiveness and deteriorati on of this product may be caused. even if this product can endure the c ondition for short time, it may c ause degradation of reliability. it is recommended that a fuse is inse rted in input line (vin) to secure safety in any abnormality such as internal circuit of isolated dc-dc converter broken down. also please take care that the external voltag e over output voltage of dc-dc converter does not applies to output of this isolated dc-dc converter.
note: 1. this datasheet is downloaded from the website of murata manufa cturing co., ltd. therefore, it ? s specifications are subject to change or our products in it may be discontinued without advance notice. pleas e check with our sales repres entatives or product engineers bef ore ordering. 2. this datasheet has only typical specific ations because there is no space for deta iled specifications. therefore, please appr ove our product s p ecifications or transact the a pp roval sheet for p roduct s p ecifications before orderin g . 2008.1.21 mpd7d06*s specification 17 13.4.3. note prior to use defectiveness and reliability de gradation may be caused if high static electricity, over rated voltage or reverse voltage are applied to this product. please be sure to avoid the followings: (1) over rating power supply, reverse power supply or inadequate c onnection of 0 v(dc)line (2) electrostatic discharge from production line and/or operator (3) electrified product from electrostatic induction please avoid an excessive mechanical shock. if this product is dropped on the floor, etc., a crack to the core of induc tors and monolithic ceramic capacitors may occur. please handle with care to avoid a strong shock to this product. do not give excessive mechanical stress to the product with your handling. please control to bend in a ma ximum of 0.2mm in your application. please keep the temperature 120 or less ,where the components shown in below are measured, under the application of forced air convection. 13.5. transportation when transporting this product, please pack it in order to avoid damage by mechanical vibration or mechanical shock, and please give instructi ons and set guidelines to the carriers to prevent rough handling. when transporting this product overseas (in par ticular, by sea), bad environment of transportation may be expected, therefore please pack this product considering mechanical strengt h, vibration-resistance and humidity-resistance. the packaging designed for domestic sa les may not suitable for overseas transportation. please contact us if this produc t with domestic packing is transported overseas. the document is for reference only and is subject to revision without notices. please contact murata for formal documentation. front back temperature measured components back front

▲Up To Search▲

Price & Availability of MPD7D067S

	To Download MPD7D067S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .