series am1d - n z 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (926 6832) f 051e r6. k 1 of 4 north america only features: ? rohs complian t ? 7 pin sip package ? operating temperature - 40 o c to + 85 o c or - 40 o c to + 105 o c on 6000v models ? high efficiency up to 8 2 % ? low profile plastic package ? 1 sec short circuit protection or continuous or continuous on 6000v mod els ? pin compatible with multiple manufacturers models single output model input voltage (v) output voltage (v) output current max ( ma ) isolation (vdc) efficiency (%) am1d - 0505s - nz 4. 5 - 5.5 5 200 1000 72 am1d - 0509s - nz 4.5 - 5.5 9 110 1000 74 am1d - 0512s - nz 4.5 - 5.5 12 83 1000 77 am1d - 0515s - nz 4.5 - 5.5 15 70 1000 79 am1d - 1205s - nz 1 0.8 - 13.2 5 200 10 00 73 am1d - 1209s - nz 10.8 - 13.2 9 110 1000 75 am1d - 1212s - nz 10.8 - 13.2 12 83 1000 79 am1d - 1215s - nz 10.8 - 13.2 15 70 1000 80 am1d - 1505s - nz 13.5 - 16.5 5 200 1000 7 2 am1d - 1512s - nz 13.5 - 16.5 12 83 1000 7 4 am1d - 1515s - nz 13.5 - 16.5 15 70 1000 7 5 am1d - 2405s - nz 2 1.6 - 26.4 5 200 1000 74 am1d - 2409s - nz 21.6 - 26.4 9 110 1000 76 am1d - 2412s - nz 21.6 - 26.4 12 83 1000 80 am1d - 2415s - nz 21.6 - 26.4 15 70 1000 81 am1d - 0505sh30 - nz 4.5 - 5.5 5 200 3000 70 am1d - 0509sh30 - nz 4.5 - 5.5 9 110 3000 75 am1d - 0512sh30 - nz 4.5 - 5.5 12 83 3000 78 am1d - 0515sh30 - nz 4.5 - 5.5 15 70 3000 80 am1d - 1205sh30 - nz 10.8 - 13.2 5 200 3000 72 am1d - 1209sh30 - nz 10.8 - 13.2 9 110 3000 76 am1d - 1212sh30 - nz 10.8 - 13.2 12 83 3000 79 am1d - 1215sh30 - nz 10.8 - 13.2 15 70 3000 81 am1d - 2405sh30 - nz 21.6 - 26.4 5 200 3000 73 am1d - 2409sh30 - nz 21.6 - 26.4 9 110 3000 77 am1d - 2412sh30 - nz 21.6 - 26.4 12 83 3000 80 am1d - 2415sh30 - nz 21.6 - 26.4 15 70 3000 82 am1d - 0505sh60 - nz 4.5 - 5.5 5 200 6000 75 am1d - 0509sh60 - nz 4.5 - 5.5 9 110 6000 75 am1d - 0512sh60 - nz 4.5 - 5.5 12 83 6000 7 8 am1d - 0515sh60 - nz 4.5 - 5.5 15 70 6000 7 8 am1d - 1205sh60 - nz 10.8 - 13.2 5 200 6000 7 8 am1d - 1209sh60 - nz 10.8 - 13.2 9 110 6000 7 9 am1d - 1212sh60 - nz 10.8 - 13.2 12 83 6000 81 am1d - 1215sh60 - nz 10.8 - 13.2 15 70 6000 81 models dual output model input voltage (v) output voltage (v) output current ( ma ) isolation (vdc) efficiency (%) am1d - 0505d - nz 4.5 - 5.5 5 100 1000 72 am1d - 0509d - nz 4.5 - 5.5 9 55 1000 75 a m1d - 0512d - nz 4.5 - 5.5 12 42 1000 78 am1d - 0515d - nz 4.5 - 5.5 15 35 1000 79
series am1d - n z 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (926 6832) f 051e r6. k 2 of 4 north america only models dual output (continued) model input voltage (v) output voltage (v) output current (ma) isolation (vdc) efficiency (%) am1d - 1205d - nz 10.8 - 13.2 5 100 100 0 74 am1d - 1209d - nz 10.8 - 13.2 9 55 1000 76 am1d - 1212d - nz 10.8 - 13.2 12 42 1000 79 am1d - 1215d - nz 10.8 - 13.2 15 35 1000 80 am1d - 2405d - nz 21.6 - 26.4 5 100 1000 74 am1d - 2409d - nz 21.6 - 26.4 9 55 1000 76 am1d - 2412d - nz 21.6 - 26.4 12 42 1000 80 am1d - 2415d - nz 21.6 - 26.4 15 35 1000 81 am1d - 0505dh30 - nz 4.5 - 5.5 5 100 3000 72 am1d - 0509dh30 - nz 4.5 - 5.5 9 55 3000 75 am1d - 0512dh30 - nz 4.5 - 5.5 12 42 3000 78 am1d - 0515dh30 - nz 4.5 - 5.5 15 35 3000 79 am1d - 1205dh30 - nz 10.8 - 13.2 5 100 3000 74 am1d - 1209dh30 - nz 10.8 - 13.2 9 55 3000 76 am1d - 1212dh30 - nz 10.8 - 13.2 12 42 3000 79 am1d - 1215dh30 - nz 10.8 - 13.2 15 35 3000 80 am1d - 2405dh30 - nz 21.6 - 26.4 5 100 3000 74 am1d - 2412dh30 - nz 21.6 - 26.4 12 42 3 000 80 am1d - 2415dh30 - nz 21.6 - 26.4 15 35 3000 81 am1d - 0505dh60 - nz 4.5 - 5.5 5 100 6000 7 5 am1d - 0509dh60 - nz 4.5 - 5.5 9 55 6000 7 5 am1d - 0512dh60 - nz 4.5 - 5.5 12 42 6000 7 8 am1d - 0515dh60 - nz 4.5 - 5.5 15 35 6000 7 8 am1d - 1205d h60 - nz 10.8 - 13.2 5 100 6000 7 8 am1d - 1209dh60 - nz 10.8 - 13.2 9 55 6000 7 9 am1d - 1212dh60 - nz 10.8 - 13.2 12 42 6000 81 am1d - 1215dh60 - nz 10.8 - 13.2 15 35 6000 81 input specifications parameters nominal typical maximum units voltage r ange 5 4.5 - 5.5 vdc 12 10.8 - 13.2 15 13.5 - 16.5 24 21.6 - 26.4 filter capacitor isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1000, 3000 & 6000 vdc resistance > 1000 mohm capacitance 60 pf output specifications parameters conditions typical maximum units voltage accuracy 5 % voltage balance dual output 1 % short circuit protection momentary (1 sec.) continuous on 6000v models line voltage regulation (single) for 1.0% of vin 1.2 % line voltage regulation (dual) for 1.0% of vin 1.2 % load voltage regulation (single) load 10~100% 10 % load voltage regulation (dual) load 10~100% 10 %
series am1d - n z 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (926 6832) f 051e r6. k 3 of 4 north america only output specifications (continued) parameters conditions typical maximum units temperature coefficient 0.03 %/ o c ripple & noise at 20mhz bandwidth 75 mv p - p general specifications parameters conditions typical maximum units switching frequency 100% load ( 6000v models only) 150 40 khz max case temperature + 125 o c op erating temperature - 40 to +85 up to +105 on 6000v models only o c storage temperature - 55 to +125 o c derating no t - required cooling free air convection humidity 90 % case material non - conductive black plastic ul 94 v - 0 weight 2 g dimensions (l x w x h) 1000 & 3000vdc 0.76 x 0.24 x 0.39 inch 19.5 x 6.00 x 10.00 mm 6000vdc 0.76 x 0.39 x 0.49 inch 19.50 x 9.80 x 12.5 mm mtbf >1 100 000 hrs (mil - hdbk - 217f, ground benign, t=+25 o c) note: all specifications in this datasheet are measured at an a mbient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified safety specifications parameters standards ul 60950 - 1: 2001 agency approvals culus (for 1000, 3000 & some 6000vdc isolated models); ce (for 3000vdc isolation models and single 1000vdc isolation models) note: all other models not referenced above are designed to meet standard iec 60950 - 1:2001 pin out specifications pin 1000 vdc 3000, 6000 vdc single dual single dual 1 + v input + v input + v input + v input 2 - v input - v input - v input - v input 4 - v output - v output no pin no pin 5 no pin common - v output - v output 6 + v output + v output no pin common 7 no pin no pin + v output + v output external capacitor C sin gle output external capacitor C dual output vin (vdc) external capacitor ( f) vout (vdc) external capacitor ( f) 5 4.7 5 10 12 2.2 9 4.7 24 1 12 2.2 - - 15 1 vin (vdc) external capacitor (f) vout (vdc) external capacitor (f) 5 4.7 5 10 12 2.2 9 4.7 24 1 12 2.2 - - 15 1
series am1d - n z 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (926 6832) f 051e r6. k 4 of 4 north america only dimensions dimensions 1000 and 3000vdc 6000vdc = note: 1. datasheets are updated as needed and as such, specifications are subject to chan ge without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based o n the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for rele ase. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com. tolerance envelope graph output current (%) o u tp u t v o l ta g e (% ) t y p i c a l l o a d l i n e +10% +5 % +2 . 5 % -2 . 5 % -7 . 5 % 10 % 50% 100 % nominal voltage 19.50 (0.76) 2.54 (0.10) 9.80 (0.39) printed face 0.50 (0.02) 0.50 (0.02) 0.25 (0.01) 1.25 (0.05) 9.8 (0.39) 12.50 (0.49) 12.00 (0.47) 4.10 (0.16) 0.50 (0.02) 19.50 (0.76) 2.54 (0.10) 6.00 (0.24) printed face 0.50 (0.02) 0.50 (0.02) 0.25 (0.01) 1.25 (0.05) 6.00 (0.24) 10.00 (0.39) 9.50 (0.37) 4.10 (0.16) 0.50 (0.02)
|
