View CSTCC10M0G53-R0_7450530.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 1 / 13 { specification of piezoel ectric ceramic resonator CSTCC10M0G53-R0 cstcc10m0g53-b0 Q date may 19, 2006 J approved by _J checked by issued by 1. m scope {?????`??k?????k ( ? ? ) ??????????????Bj this product specification is applied to the piezoelectric ceramic resonator used for time base oscillator in a microcomputer. please contact us when using this product for any other applications than described in the above. 2. ? FvB part number ? murata part number F ? customer's part number F customer's drawing number ?`?? taping CSTCC10M0G53-R0 ? bulk cstcc10m0g53-b0 3. Q appearance and dimensions 3-1 Q : ??????Re???A?? appearance : no illegible mark ing. no visible dirt. 3-2 ? ? ? : 1 ???`??????? ? dimensions of component : see figure 1. dimensions of taping type and bulk type are the same. 3-3 : ???R????T? ???w???? construction : resonator and capacitor elements are mounted onto ceramic substrate, then metal cap covers over the elements.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 2 / 13 4. ?? electrical characteristics ?? item ? specification 4-1 ?k? nominal oscillating frequency 10.000mhz 4-2 k?S? *1 initial tolerance *1 0.50% 0.50% max. 4-3 ? resonant impedance 25 25 max 4-4 i (c1,c2) built-in load capacitance (c1,c2) 15pf 20% ( ) 15pf 20% max. (ref.) 4-5 ~F? insulation resistance 500m (d.c.10v ??r ) 500m ? min. (applied d.c. 10 v) 4-6 ?R withstanding voltage d.c.100v, 5 d.c.100v, 5 seconds max. 4-7 ?R rated working voltage (1) ??R d.c. voltage (2) ? a.c. voltage d.c.6 v 15 vp-p. 4-8 k?? frequency shift by temperature (-20 +80 ??? ) (-20c to +80c) ??? operating temperature range ?? storage temperature range 0.3% ( ?? ) 0.3%max. (from initial value) -20 +80 -20c to +80c -55 +85 -55c to +85c 4-9 k?` *2 oscillating frequency aging *2 0.3% ( ?? ) 0.3%max. (from initial value) *1 ? ? ?????A?? 0.60% ???? terminal (1) and (3) are interchangeable, but if interchange initial tolerance is 0.60%max. *2 ? +85 2 1000 rg? 1 rgy? components shall be left in a chamber of +85 2 c for 1000 hours, then measured after leaving in natural condition for 1 hour.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 3 / 13 5. C physical characteristics ? item ? Y test condition ?Y? specification after test 5-1 n random drop 1.0m ?? 3 ? y? components shall be measured after 3 times random dropping on the wooden plate from the height of 1.0m. Q?? 1 4-3 no visible damage and the measured values shall meet table 1 and 4-3. 5-2 vibration resistance ? 10 55hz ? 1.5mm x,y,z 3 2 rg y? applying the vibration of amplitude 1.5mm and vibration frequency 10 to 55hz in each of 3 perpendicular directions for 2 hours. 1 4-3 the measured values shall meet table 1 and 4-3. 5-3 B ? bend strength pcb ????R 1 1 ? 5 ? R? after components soldered on pcb, the load shall be applied to the pcb as shown in below figure for 5 times (1 second per 1 time). 20 10 part pcb r10 45 45 load deflection stick 5 supporter 1 off-center ?R ?R 1 ??` ? 5 ?? 1 1 4-3 the measured values shall meet table 1 and 4-3.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 4 / 13 5-4 ? resistance to soldering heat (1) ` ? (1) re-flow soldering ? ? ? ` 2 ? ? ? 1 rgy? components shall be measured after applying twice of the re-flow soldering with following temperature profile and leaving in natural condition for 1 hour. gradual cooling ?? heating pre-heating ?` peak (150-180c) 60 - 120 / sec. (230c) (260c / max.) 30 sec. min. 40 sec. max. 120 sec. min. temperature (c) 15 0 180 2 3 0 1 4-3 the measured values shall meet table 1 and 4-3. (2) ? (2)soldering with iron ? +300 5 3.0 0.5 g? 24 rg?y? ? O ?? ??? components shall be measured after soldering at +3005c for 3.00.5 seconds and leaving in natural condition for 24 hours. the soldering iron shall not touch the components while soldering. Q?? 1 4-3 no visible damage and the measured values shall meet table 1 and 4-3. 5-5 ? solderability lf ? (sn-3ag-0.5cu pct ? ??? +105 c ? 100%r.h. ? ? 4 rg`????? ? ` ? 5 ? +245 5 c ? 3 0.5 g lf solder (sn-3ag-0.5cu after being kept in pressure cooker at +105 c temperature and 100%r.h. for 4 hours, terminals of components shall be immersed in a soldering bath at temperature of +245 5 c for 3 0.5 seconds after being placed in a rosin- methanol for 5 seconds. ? 90% ??? ?? the solder shall coat at least 90% of the surface of terminal. 5-6 ? washability ?? see table 2. Q?? 1 4-3 no visible damage and the measured values shall meet table 1 and 4-3.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 5 / 13 6. environmental characteristics ? item ? Y test condition ?Y? specification after test 6-1 dry heat (storage) ? +85 2 1000 rg? ? ? 1 rg?y? components shall be left in a chamber (temperature: +852c) for 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 the measured values shall meet table 1 and 4-3. 6-2 cold (storage) ? -55 2 1000 rg? ? 1 rgy? components shall be left in a chamber (temperature: -552 c) for 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 the measured values shall meet table 1 and 4-3. 6-3 ? humidity ? +60 2 ? 90 + ? 5 0 %r.h. ? ? 1000 rg?? ? 1 rg?y? components shall be left in a chamber (90 to 95%r.h. at +602c) 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 the measured values shall meet table 1 and 4-3. 6-4 n thermal shock ? -55 c 30 g?? +85 c ? 30 g? ? 1 ? ? 10 ? 1 rg?y ? after performing 10 cycles of thermal test (- 55c 30 minutes to +85c 30 minutes), components shall be left in natural condition for 1 hour. 1 4-3 the measured values shall meet table 1 and 4-3. 6-5 c?F salt mist test ? +35 2 ? 5 1% 48 r gBA F ? ? 1 rgy ? after being placed in a chamber with +352c, density 51% (by weight) for 48 hours and then being placed in natural condition for 1 hour, resonator shall be measured. ??? ? 1 4-3 ? there shall be no evi- dence of destructive corrosion and the measured values shall meet table 1 and 4-3. 6-6 sulfuration ?? 1000ppm 24 rg? ? 1 rgy? after being placed in a chamber with 1000 ppm sulfur density for 24 hours and then being placed in natural condition for 1 hour, resonator shall be measured. ? ??? 1 4-3 no breakdown and the measured values shall meet table 1 and 4-3.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 6 / 13 1 table 1. ? item ?Y specification after test k? oscillating frequency 0.3% ?? 0.3%max. (from initial value) 7. y test circuit 7-1 k? : 2 ?? oscillating frequency : see figure 2. 7-2 : ? ?? ? equivalent circuit constants : vector impedance analyzer hp4194a or equivalent. 7-3 y : ? +25 3 ? 60 10%r.h. ? y? B ? x ??? +5 +35 ? 45 85%r.h. ?y? measuring condition : standard conditi ons for the measurement shall be +253c temperature and 60 10%r.h. humidity. the measurement shall be performed at the temperature of +5 to 35c and the humidity of 45 to 85%r.h. unless otherwise the result is doubtful. 8. ? ? ? packaging standard (bulk) ?g u? 500 ? ?? ??? each minimum package unit of products (500 p cs) shall be in a carton box and it shall be clearly marked with part number, quantity and outgoing inspection number. 9. ?`?? ? ? packaging standard (taping) 9-1 ?`? ? ( ?`?? ? ? r ? ? ?? ) ?? the tape for components shall be wound clockwise. the feeding holes shall be to the right side as the tape is pulled toward the user. 9-2 ??? 1 ` 2,000 {? a reel shall contain 2,000pcs of components. 9-3 ? ??`?? 3 ?? dimensions of plastic tape are shown in figure 3. 9-4 ? ? ` ? 4 ?? dimensions of plastic reel are shown in figure 4.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 7 / 13 10. ! ? cautions 10-1 ? limitation of applications u???? ?` ? ?b ?? ? m ? ? ???? ? ??? ? ??? Bj ? C C ? C k C ? C ? C ( ? ? ) ?? ??C ? C I C ? ? C ??C please contact us before using our products fo r the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party ? s life, body or property. aircraft equipment aerospace equipment undersea equipment power plant control equipment medical equipment transportation equipment(vehicles, trains, ships, etc.) traffic signal equipment disaster prevention / crime prevention equipment data-processing equipment applications of similar complexity and/or wi th reliability requirements to the applications listed in the above 10-2 ? ` ` C? ? fail-safe u? ? ? ? ? ?? ?m ? ` ` C? ? ? be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 8 / 13 11. ?? ? caution for use 11-1 ??n????? ? ??? ? Q ? ? the component may be damaged if excess mechanical stress is applied. 11-2 ? H u? ?BC ?? ? ? please do not apply excess mechanical st ress to the component and terminals at soldering. 11-3 ?? ?? ???? _J?? conformal coating of the component is accept able. however, the re sin material, curing temperature, and other process conditions s hould be evaluated to confirm stable electrical characteristics are maintained. 11-4 ? ?k??k k????k ?? k ??? _J?? irregular or stop oscillation may o ccur under unmatched circuit conditions. 11-5 u?? JR? ?Q C g? C? ?? g? ? ? ^ n? u? ?p ????? g? C ?u _J??? ? ?C? g? C? g? ? ? ??????? the component is recommended with placement machines with employ optical placement capabilities. the component might be resulted in damage by excessive mechanical force. please make sure that you have evaluated by using placement machines before going into mass production. do not use placement mach ines which utilize mechanical positioning. please contact murata for details beforehand.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 9 / 13 12. u? ? ? notice on product storage 12-1 ? -10 +40 ? 15 85% ? ? ? ?? please store the products in room where the te mperature / humidity is stable. and avoid such places where there are large temperatur e changes. please store the products under the following conditions : temperat ure : -10 to +40 (degree c) humidity : 15 to 85% r.h. 12-2 u? _y _ ? B ??{ 6 g?{ 6 ??? 6 ? ??? ????_J?? expire date (shelf life) of the products is 6 months after delivery under the conditions of a sealed and an unopened package. please use the products within 6 months after delivery. if you store the products for a long time ( more than 6months ), use carefully because the products may be degraded in the solder-ability and/or rusty. please confirm solder-ability and characteristics for the products regularly. 12-3 ? c C ? ? ? ??? ? ? ? ???? ? ? ? please do not store the products in a chemical atmosphere (acids, alkali, bases, organic gas, sulfides and so on), because the characteri stics may be reduced in quality, and/or be degraded in the solder-ability due to the storage in a chemical atmosphere. 12-4 ? ? m ? ? ? ? ?? ? ? please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. 12-5 ? ? ? ? please do not store the products in the places such as : in a damp heated place, in a place where direct sunlight comes in, in place applying vibrations. 12-6 _y _ ? L ? ?? ? r ????? ?? ? ?? _y _ ?? please use the products immediately after t he package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solder-ability due to storage under the poor condition. 12-7 u???u????? ? ? ???? ?? B ? ? ?Q ? please do not drop the products to avoid cracking of ceramic element.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 10 / 13 13. ! note: 13-1 ?? H ???Fu? g? ?? B ?u please make sure that your product has been evaluat ed in view of your specifications with our product being mounted to your product. 13-2 u???{? ? d ? ??? you are requested not to use our product dev iating from this product specification. 13-3 ?{?F I ? ? ?? 1 ? ? ?? ? ?? ?{? ? ?? ? ??{?? r I ? ?? ? please return one duplicate of this product s pecification to us with your signature to acknowledge your receipt . in case of no return within three months from submission date, or if we receive order before the duplicate is re turned, this product specification will be deemed to have been received by you. 13-4 ?? gY ?? ? v s ? ? d ??m ??? ? ?? ?? F\ ? gY ?? | ^ I ?? ? v ? d ?? ? ? d o ?? ??? ???e? ? s ?? ? ? ? we consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 11 / 13 1 ? figure 1. dimensions w: 7.2 0.2 l: 3.0 0.2 t: 1.55 0.05 : vender's code : u? eiaj monthly code g :mm in mm 2 k?y figure 2. test circuit ceralock ? : CSTCC10M0G53-R0 cstcc10m0g53-b0 ic:1/6 cd4069ube x2 (rca) vdd:+5 0.1v rf:1m l t 2.1max. (3) (2) (1) 0.450.30 6.6max. w 1.20.2 0.45(ref.) 0.45(ref.) 0.45(ref.) 0.30.30 0.50.05 1.40.2 1.20.2 1.10.1 2.50.1 2.50.1 * 100 1.2 1.4 1.2 1.2 1.2 land pattem 3.8 4.4 2.5 2.5 ( ?X? (recommendable land pattern ???`? (to frequency counter) output vdd c1 c2 rf (1) (3) (2) ceralock r
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 12 / 13 3 ? ??`?? figure 3. dimensions of plastic tape (CSTCC10M0G53-R0) 2.00.05 4.00.1 ?1.5 +0.3 -0.0 3max. 7.60.1 5.50.05 12.00.2 1.750.1 0.30.05 10 ? `? g mm ? ?` 300mm (9.5) cover film direction of feed the cover film peel strength force the cover film peel speed 300mm/min. in mm 4.00.1 0.1 0.7n 0.1 0.7n ?1.550.05 3.30.1 b (3) (2) (1) t1 *1 t2 *1 *1 : ? ???? *1 : dimensions varies with frequency range of component 4 ? ? ` ? figure 4. dimensions of plastic r eel (CSTCC10M0G53-R0) 2.0 0.5 180 g mm 160 /min. ?`` `` ??? ? `?` ? trailer empty components empty leader cover film in mm 160 190 400 560mm 13.0 +1.0 0 13.0 0.2 400 to 560mm 160 to 190 17.0 1.0 0 -1.5 ? frequency range 2.00 2.99mhz 3.00 10.0mhz t1 1.85 0.05mm 1.65 0.05mm t2 2.45max. 2.25max.
? drawing no. jgc42-5451 ?\?u murata manufacturing co.,ltd. p. 13 / 13 2 table 2 ? washability ?? cleaning solvent ? item ??? (hcfc) ipa ? ?????? 750h ???????? 100s ????? frw hcfc, isopropanol, tap water, demineralized water cleanthrough750h, pine alpha 100s , techno care frw u? ?? ?? : t *1 temperature difference: t *1 [ t= u?? - ?? ? ] [ t = component - solvent] t Q 60 ??? t Q 60c ? condition (1) ? ultrasonic wash ? +60 ??? ? 28khz 20w/l ? 1 1 minute max. in above solvent at +60c max. (frequency : 28khz, output : 20w/l) (2) n ? immersion wash ? +60 ??? 5 n ? 5 minutes max. in above solvent at +60c max. (3) ???? ? ? ? shower or rinse wash ? +60 ??? 5 Q ? ? ` ? 5 minutes max. in above solvent at +60c max. (4) ? drying +80 R ` ` 1 5 g ? ? 5 minutes max. by air blow at +80c max. *1 ex. u?? +90 r +60 ?? n t=30 ??? in case the component at +90c immerses into cleaning solvent at +60c, then t=30c. ? notice: 1 ? L rg ? ? ???? ` 10 ?? total washing time should be within 10 minutes. 2 g? ? B ? ?k??? ? u ? please insure the component is thoroughly evaluated in your application circuit. 3 c ? ? ?? ? ? ? ? ? ? ? ?k? ????? ? the component may be damaged if it is washed with chlorine, petroleum or alkali cleaning solvent.

▲Up To Search▲

Price & Availability of CSTCC10M0G53-R0

	To Download CSTCC10M0G53-R0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .