do not scale from this print isdf-xx-s-x no of positions -02 thru -50 row specification -s: single row notch specification -r: retention latch (available on pos -05 thru -50) (see sheet 3, fig 2) (see note 10) .200 .130 .0700 .0950 .020 (typ) .025 (typ) (no of pos x .050) - .050 (tol non-accum) ((no of pos x .050) + .021) - .005 + .002 r .001 "a" "a" "b" "b" a see note 3 c1 .050 .0800 .0020 r .001 .030 'd' "c" "c" section "a"-"a" .0260 .0420 section "b"-"b" c2 c3 .003 .440 .415 .4260 r .005 (typ) .077 .103 .058 .0525 .0430 .2180 .0410 r .010 (typ) 'e' section "c"-"c" c4 c5 c7 c6 .003 'f' 01 02 03 04 05 07 06 see note 8 see note 7 .030 .033 .050 see note 4 c fig. 1 isdf-07-s shown see note 2 sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [0.3] 2 .xxx: .003 [0.08] .xxxx: .0015 [0.038] material: .050" cl crimp wire socket insulator by: isdf-xx-s-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing gaynor 6/10/2008 3 1 sheet scale: 4:1 vectra s475, color: black c:\enterprisevault\dwg\misc\mktg\isdf-xx-s-x-mkt.slddrw notes: 1. represents a critical dimension. 2. samtec logos shall appear at locations on surface shown, approximately .075 x .055 (both sides). 3. all multiple cavity molds shall identify each cavity with a letter designation located where shown. 4. identification marks not to protrude beyond .001 above the surface of the insulator material. 5. molded surfaces shall be consistent and smooth. surfaces to be free of scatches, nicks, sink areas, voids or other blemishes. 6. part to be symmetric about the centerline within +/-.0015, unless otherwise stated. 7. gate pads must be recessed .005. 8. specified positions to be identified where shown (note 4 applies). 9. r.005 optional. 10. option not for sale. for retention latch feature, see isdf-xx-s-m print. max regrind: 50% max flash allowed: .002 max gate vestige: .004 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision d
90 .0350 - .0010 + .0015 sq. .0120 .040 sq. .0220 sq. detail 'd' scale 16 : 1 c8 30 .0075 r .0025 (typ) detail 'e' scale 16 : 1 detail 'f' scale 16 : 1 sheet of .050" cl crimp wire socket insulator by: isdf-xx-s-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing gaynor 6/10/2008 3 2 sheet scale: 1:0.166667 c:\enterprisevault\dwg\misc\mktg\isdf-xx-s-x-mkt.slddrw revision d 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
((no of pos x .050) + .015) - .002 + .000 .440 ref .020 .120 .1020 .0020 'j' "h" "h" c11 .0270 .0190 30 (typ) .005 .002 (typ) 15 .0022 45 detail 'j' scale 12 : 1 ((no of pos x .050) + .145) - .005 + .002 ((no of pos x .0500) + .0700) .002 .200 'k' c10 .1740 .0300 .065 .1480 5 .360 .002 section "h"-"h" c9 .0095 - .0005 + .0010 .0140 .0010 r .0020 (typ) .015 45 x r .004 (4 plcs) detail 'k' scale 10 : 1 fig. 2 -r: retention latch option (see note 10) (isdf-05-s-r shown) (same as fig. 1 except as shown) sheet of .050" cl crimp wire socket insulator by: isdf-xx-s-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing gaynor 6/10/2008 3 3 sheet scale: 6:1 c:\enterprisevault\dwg\misc\mktg\isdf-xx-s-x-mkt.slddrw revision d 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
