1030 mhz saw filter 12 mhz bandwidth part number: MN95015 idt saw products 324 clark street, worcester, ma 01606, usa ph 1-508-852-5400 fax 1-508-852-8456 www.idt.com dsMN95015 rev - 25-aug-2009 ecn 36540 page 1 of 3 description 1030 mhz saw bandpass filter with 12 mhz bandwidth . 3 x 3 mm lcc package. rohs compliant. typical performance horizontal: frequency : 20 mhz/div relative magnitude : 10 db/div relative magnitude : 1 db/div group delay variation : 25 ns/div s11 (930 C 1130 mhz) s22 (930 C 1130 mhz)
1030 mhz saw filter 12 mhz bandwidth part number: MN95015 idt saw products 324 clark street, worcester, ma 01606, usa ph 1-508-852-5400 fax 1-508-852-8456 www.idt.com dsMN95015 rev - 25-aug-2009 ecn 36540 page 2 of 3 specification parameter min typ max units center frequency, f c 1 - 1030 - mhz insertion loss at fc - 2.7 3 db 1db bandwidth - 12 - mhz lower 3 db band edge 2 - 1021 1022.5 mhz upper 3 db band edge 2 1037.5 1039 - mhz group delay variation (fc +/- 4 mhz) - 16 25 ns p-p amplitude variation (fc +/- 2.5 mhz) at 25?c 0.35 0.4 db p-p relative attenuation (10 to 1000 mhz) 2 40 43 - db relative attenuation (1000 to 1010 mhz) 2 32.5 34 - db relative attenuation (1050 to 1060 mhz) 2 32.5 40 - db relative attenuation (1060 to 1500 mhz) 2 40 44 - db relative attenuation (1500 to 2200 mhz) 2 20 35 - db relative attenuation (2200 to 3000 mhz) 2 5 30 - db input/output vswr - 1.3 1.5 :1 temperature coefficient of frequency - -32 - ppm/?c source/load impedance 50 ohms ambient temperature - 25 - ?c notes: 1. defined as the average of the lower and upper 3 db frequencies at room ambient. 2. all db levels are defined relative to the inse rtion loss. maximum ratings parameter min max units storage temperature range -50 125 ?c operating temperature range -40 85 ?c input power level: cw in-band pulse (10 us width at 1% duty cycle) @ fc pulse out-of-band (10 us width at 1% duty cycle ) (fc+/-30 mhz) pulse out-of-band (10 us width at 1% duty cycle ) (fc+/-32 mhz) +20 +32 +37 +32 - - - - dbm dbm dbm dbm matching circuit notes: 1. matching components are not required. input 50 w single-ended output 50 w single-ended gnd gnd 2 5 1,3,4,6
1030 mhz saw filter 12 mhz bandwidth part number: MN95015 idt saw products 324 clark street, worcester, ma 01606, usa ph 1-508-852-5400 fax 1-508-852-8456 www.idt.com dsMN95015 rev - 25-aug-2009 ecn 36540 page 3 of 3 package outline suggested footprint marking iso 9 001 registered all specifications are believed to be accurate and reliable. however, mnc reserves the right to make changes without notice. ? 2009 all rights reserved. package material: body: al 2 o 3 ceramic lid: kovar, ni plated terminations: au plating 1 m min, over a 1.3-8.9 m ni plating units: mm tolerances are 0.15 mm except where indicated. pad configuration: input: 2 output: 5 ground: 1,3,4,6
|