legend +25 oc +85 oc - - - - - - -55 oc typical intermodulation performance at 25 oc second order harmonic intercept point........+52 dbm (typ.) second order two tone intercept point.........+46 dbm (typ.) third order two tone intercept point.............+27 dbm (typ.) available as: TM9064, 4 pin 0.500? to-8 (t4) tn9064, 4 pin 0.450? sq. surface mount (sm3) bx9064, sma connectorized housing (h1l-laser) bxp9064, sma connectorized housing (hpak) features ?? ?? ?? ?? ?? ultra broad bandwidth 100-3000 mhz ?? ?? ?? ?? ?? high gain: 18.5 db typical ?? ?? ?? ?? ?? cross to the cougar ac3064, our model bx9064 ?? ?? ?? ?? ?? cross to the cougar acp3064, our model bxp9064 ?? ?? ?? ?? ?? screening to the tables of mil-std-883 available note: care should always be taken to effectively ground the case of each unit. specifications typical performance data maximum (no damage) ratings ambient operating temperature ................ -55oc to +100 oc storage temperature ................................. -62oc to +125 oc case temperature .................................................. +125 oc dc voltage .......................................................... +17 volts continuous rf input power .................................. +13 dbm short term rf input power .... 100 milliwatts (1 minute max.) maximum peak power .................... 0.5 watt (3 sec max.) rf amplifier model TM9064 revision 5/16/2012 spectrum microwave 1900 west college ave. state college, pa. 16801 ph (888) 553-7531 fax (888) 553-7532 spectrum microwave 2707 black lake place philadelphia, pa. 19154 ph (215) 618-3700 fax (215) 464-4001 www.spectrummicrowave.com characteristic typical min/max ta= 25 oc ta = -55 oc to +85 oc frequency 100 - 3000 mhz 100 - 3000 mhz power vdc +15 +15 ma 80 88 max. vswr in 1.5:1 2.0:1 max. out 1.5:1 2.0:1 max. reverse isolation (db) -36 db - noise figure (db) (400-3000 mhz) 3.3 db 4.5 db max. (100-400 mhz) 4.5 db 5.5 db max. gain 18.5 db 16.5 db min. gain flatness +/- 0.3 db +/- 0.8 db max. power output @ 1 db comp. (dbm) +16.5 dbm +15.0 dbm (typical at 25oc under a +15 volt supply) 2.0 1.5 1.0 2.0 1.5 1.0 2 17 +18 +17 +16 +15 +14 0 -10 -20 -30 -40 20 21 19 18 start 100 mhz stop 3000 mhz start 100 mhz stop 3000 mhz start 100 mhz stop 3000 mhz start 100 mhz stop 3000 mhz start 100 mhz stop 3000 mhz start 100 mhz stop 3000 mhz 10 8 6 4 gain (db) reverse isolation (db) noise figure (db) input vswr output vswr 1 db comp. (dbm)
.33 max. 8.38 1.52 38.61 touching, removing or inserting use esd precautionary procedures when to damage by electrostatic discharge (esd). this assembly contains parts sensitive caution revisions ecn rev. description chng/date appvd/date xxx p1 preliminary release 2012/05/14 .29 7.30 .18 4.57 1 3 place decimal .005 2 place decimal .02 * tolerances are: angles 1.0 * dimensions are in inches * dimensional limits apply before processes * parenthetical information for reference only * dimensioning and tolerancing iaw asme y14.5-1994 63 * surface finish * machined tool mismatch: .002 max. * concentricity machined dia: .002 fim * remove all burrs and sharp edges .010 rad max. * interpret drawing iaw asme y14.100-2004 do not scale drawing unless otherwise specified 2012/05/14 war 2012/05/14 h pham b size scale: title date drawn engrg qa mfg checked see separate parts list in electronic storage philadelphia, pa 19154-1008 (usa) 2707 black lake place spectrum microwave, inc 1 ansi 088-00304 a outline, hpak 1 1 dwg no. sheet of cage code 60979 rev p1 written permission of spectrum microwave, inc are prohibited. reproduction of this document, in whole or in part, without the the release of data contained in this document and the spectrum microwave proprietary information this document is the sole proper ty of spectrum microwave, inc. form no. 1054 size b1 3rd angle projection generated using solidworks 2007 088-00304 dwg no. sh rev p1 1.5:1 of 1 1 2 3 4 a 43 b computer assisted drawing b smi vdc rf out rf in xxxxxx xxxx 2x sma connector 14.61 .58 8.38 .33 11.56 .46 6.36 19.56 .77 .25 .38 9.53 typ. 2x .03 0.76 ground tab 12.32 3.62 .14 .44 11.05 1.78 .07 .49 mounting holes 4 x 2-56 unc .10[2.54]
|
