design and specifications are each subject to change without notice. ask factory for the current technical specifications before purchase and/or us e. should a safety concern arise regarding this product, please be sure to contact us immediately. detector switches/ese18 1 e 2 s 3 e 4 5 6 7 8 9 product code design no 8 1 6th l r left-side operation type right-side operation type type 1hl detector switches type: ese18 n features l thin body: 1.2 mm l circuit type: normally-open and a normally-closed types are available. l travel: standard type: 1.5 mm long type: 2.15 l surface mounted type: packed with embossed tape. supports reflow soldering. n major specifications japan n recommended applications l mechanisms or the detection of media in portable equipment (e.g. md/cd-rom/dvd players, dscs) l operation switches (input devices) n explanation of part numbers power rating 50 a 3 v dc to 10 ma 5 v dc contact resistance 1 w max. insulation resistance 100 m w max. (100 v dc) dielectric withstanding voltage 100 v ac for 1 minute operating force 300 mn max. full travel 1.5 mm, 2.15 mm operating life 50000 cycles min. temperature range _ 10 ?c to +60 ?c heat resistance +70 ?c for 96 hours low temperature resistance _ 25 ?c for 96 hours humidity resistance +40 ?c 90 % to 95 % rh for 96 hours ese18l 5000 pcs. minimum quantity/packing unit ESE18R ese18l 30000 pcs. quantity/carton ESE18R (reel pack) detector switches that contribute to miniaturization, weight reduction, and expansion of the operation variety required for portable equipment.
detector switches/ese18 design and specifications are each subject to change without notice. ask factory for the current technical specifications before purchase and/or us e. should a safety concern arise regarding this product, please be sure to contact us immediately. (1.2) 1.0 0.25 (52.4?) (14.7?) 0.65 r0.3 2.6 max. 5.4 3.2 1.8 3.6 0.25 1.15 3.0 1.2 3.8 0.54 0.25 0.4 0.5 0.5 2.7 4.0 1.20.2 f 0.60.05 3.4 0.5 2.9 2.6 (2) 1.4 1.0 0.75 0.7 0.7 0.5 0.25 2.00.1 operation point full stroke position pivot center pivot center dummy terminal case center on start position off start position on angular terminal off angular terminal a c t i o n d i r e c t i o n 3.6 1.8 4.1 3.0 1.2 0.25 1.15 3.2 5.4 1.20.2 0.4 0.25 3.4 2.00.1 1 0.60.05 1.0 (1.2) 4 2.9 0.5 0.5 2.6 (2.0) 1.4 0.7 0.7 0.75 2 3 2 0.5 2.7 4.0 0.5 0.54 0.65 r0.3 2.6 max. 5 (14.7?) (52.4?) 1.0 full stroke position (pivot center) pivot center operation point dummy terminal case center mfg. no. (marking direction is arbitrary) on start position off start position on start position off start position on angular terminal off angular terminal a c t i o n d i r e c t i o n (1.2) 1.0 0.25 (52.4?) (14.7?) 0.65 r0.3 2.6 max. 0.54 0.25 0.4 0.5 0.5 2.7 4.0 1.20.2 f 0.60.05 3.4 0.5 2.9 2.6 (2) 1.4 1.0 0.75 0.7 0.7 0.5 0.25 2.00.1 5.4 3.2 1.8 3.6 0.25 1.15 3.0 1.2 3.8 operation point full stroke position on start position off start position on start position off start position pivot center pivot center on angular terminal off angular terminal dummy terminal case center a c t i o n d i r e c t i o n n dimensions in mm (not to scale) no. 1 no. 2 standard stroke type ese18l straight terminals 1-pole 1-throw no. 3 recommended pwb piercing plan (pitch tolerance: 0.05) recommended pwb piercing plan (pitch tolerance: 0.05) recommended pwb piercing plan (pitch tolerance: 0.05) standard stroke type ese18l j-bent terminals 1-pole 1-throw standard stroke type ESE18R j-bent terminals 1-pole 1-throw nomal open with boss ese18lj02 ese18l11b nomal open without boss ese18lj01 ese18l11a nomal closed with boss ese18l61b nomal closed without boss ese18l61a nomal open with boss ese18lf02 ese18l11d nomal open without boss ese18lf01 ese18l11c nomal closed with boss ese18l61d nomal closed without boss ese18l61c nomal open with boss ESE18Rj02 ESE18R11b nomal open without boss ESE18Rj01 ESE18R11a nomal closed with boss ESE18R61b nomal closed without boss ESE18R61a
design and specifications are each subject to change without notice. ask factory for the current technical specifications before purchase and/or us e. should a safety concern arise regarding this product, please be sure to contact us immediately. detector switches/ese18 a c t i o n d i r e c t i o n 5 4 3 2 1 2 (1.2) 1.0 0.60.05 2.9 2.00.1 3.4 0.4 0.25 1.20.2 2.6 1.4 (2.0) 1.0 0.75 0.7 0.5 0.7 0.5 0.5 2.7 4.0 0.5 full stroke position (pivot center) operation point 0.54 r0.3 0.65 2.6 max. pivot center dummy terminal case center mfg. no. (marking direction is arbitrary) (14.7 ?) (52.4 ?) 3.2 5.4 1.2 3.6 1.8 4.1 3.0 0.25 1.15 on start position off start position on start position off start position on angular terminal off angular terminal (52.4?) (14.7?) 0.25 1.0 0.75 0.7 0.4 3.4 2.00.1 f 0.60.05 (1.2) 1.20.2 0.25 0.25 0.5 0.5 0.65 4.0 2.7 0.5 0.5 1.0 (3.2) 0.7 1.4 (2.0) 3.1 3.55 0.54 r0.3 3.2 3.8 3.0 1.2 3.6 0.25 1.15 5.4 1.8 full stroke position (pivot center) pivot center operation point case center mfg. no. (marking direction is arbitrary) on start position off start position on start position off start position on angular terminal off angular terminal full stroke position (pivot center) pivot center operation point case center mfg. no. (marking direction is arbitrary) on start position off start position on start position off start position on angular terminal off angular terminal (52.4?) (14.7?) 0.25 1.0 0.75 0.7 0.4 3.4 2.00.1 f 0.60.05 (1.2) 1.20.2 0.5 0.65 4.0 2.7 0.5 1.0 (3.2) 0.7 1.4 (2.0) 3.1 3.55 0.54 r0.3 3.2 4.1 3.0 1.2 3.6 0.25 1.15 5.4 1.8 0.5 no. 4 no. 6 no. 5 n dimensions in mm (not to scale) recommended pwb piercing plan (pitch tolerance: 0.05) standard stroke type ESE18R straight terminals 1-pole 1-throw nomal open with boss ESE18Rf02 ESE18R11d nomal open without boss ESE18Rf01 ESE18R11c nomal closed with boss ESE18R61d nomal closed without boss ESE18R61c nomal open with boss ese18l12b nomal open without boss ese18l12a nomal closed with boss ese18l62b nomal closed without boss ese18l62a nomal open with boss ese18l12d nomal open without boss ese18l12c nomal closed with boss ese18l62d nomal closed without boss ese18l62c recommended pwb piercing plan (pitch tolerance: 0.05) recommended pwb piercing plan (pitch tolerance: 0.05) long stroke type ese18l straight terminals 1-pole 1-throw long stroke type ese18l j-bent terminals 1-pole 1-throw
detector switches/ese18 design and specifications are each subject to change without notice. ask factory for the current technical specifications before purchase and/or us e. should a safety concern arise regarding this product, please be sure to contact us immediately. c c dummy dummy common tarminal dummy dummy common tarminal c c dummy dummy common tarminal dummy dummy common tarminal 2.7 4.0 0.65 f 0.60.05 2.00.1 0.4 0.25 (1.2) 1.2 0.2 1.0 3.2 5.4 1.8 3.6 0.5 1.2 0.25 1.15 3.0 3.8 0.5 0.25 3.4 0.25 0.5 (3.2) 0.5 0.7 0.75 0.7 1.0 1.4 (2.0) 3.1 0.54 r0.3 3.55 (14.7 ?) (52.4 ?) operation point full stroke position pivot center pivot center dummy terminal case center on start position off start position on angular terminal off angular terminal 2.7 4.0 0.65 f 0.60.05 2.00.1 3.4 0.4 0.25 (1.2) 1.20.2 1.0 3.2 5.4 1.8 3.6 0.5 1.2 0.25 1.15 3.0 0.5 0.5 4.1 (3.2) 0.5 0.7 0.75 0.7 1.0 1.4 (2.0) 3.1 0.54 r0.3 3.55 (14.7 ?) (52.4 ?) full stroke position (pivot center) pivot center operation point case center mfg. no. (marking direction is arbitrary) on start position off start position on start position off start position on angular terminal off angular terminal dummy terminal no. 8 nomal open with boss ESE18R12b nomal open without boss ESE18R12a nomal closed with boss ESE18R62b nomal closed without boss ESE18R62a nomal open with boss ESE18R12d nomal open without boss ESE18R12c nomal closed with boss ESE18R62d nomal closed without boss ESE18R62c n dimensions in mm (not to scale) n circuit diagram nomal open type 1-pole 1-throw (n . o) type ese18l type ESE18R nomal closed type 1-pole 1-throw (n . o) type ese18l type ESE18R recommended pwb piercing plan (pitch tolerance: 0.05) recommended pwb piercing plan (pitch tolerance: 0.05) no. 7 long stroke type ESE18R straight terminals 1-pole 1-throw long stroke type ESE18R j-bent terminals 1-pole 1-throw
design and specifications are each subject to change without notice. ask factory for the current technical specifications before purchase and/or us e. should a safety concern arise regarding this product, please be sure to contact us immediately. detector switches/ese18 packed portion cover tape carrier tape end top drawing direction pilot holes leading portion 400 mm min. non-packed portion (160 mm min.) non-packed portion (100 mm min.) 16.00.3 1.750.1 7.50.1 p=8.00.1 4.00.1 2.00.1 f 1.5 +0.1 0 13.5 ( f 80.0) f 380.02.0 24.4 2.0 2.0 n packaging specifications standard reel dimensions in mm (not to scale) taping reel embossed carrier taping standard stroke type long stroke type
|
