14 +0.2 0 6 +0.2 0 1.0 2.0 2.5 2.0 0.5 square c e k an 1.27 2.54 1.0 2.55/2.50 5.1+0.1-0.0 7.0 max 0.5+/-0.1 1.0 min wall opi 1000l series optically coupled isolators surface mount low profile atex & iecex certified the opi 1000l a through e are a series of optically coup led isolators each consisting of a infrared emitter coupled to a silicon photo transistor. the series is designed for applications requiring high voltage isolation between input & output . surface mount configuration in tape & reel high current transfer ratioC 40% min @ 1ma if low profile 10kv isolation bedford opto technology ltd 1,biggar business park, biggar, lanarkshire, ml12 6fx tel: +44 (0) 1899 221221 fax: +44 (0) 1899 221009 website: bot.co.uk e - mail: bill@bot.co.uk iss p 20.10.12 1/6 pb these components are rohs compliant certificate no. iecex bas 06.0021u/4 confirmed conform to: - iec 60079 - 0:2011 edition 6 iec 60079 - 11:2011 edition 6 iec 60079 - 26:2006 edition 2 conditions of use apply: - see schedule of limitations on certificate / details repeated on page 5 of this datasheet. certificate no. - bas01atex1278u/5 confirmed conform to: - en60079 - 0:2012 en60079 - 11:2012 en60079 - 26:2007 conditions of use apply: - see schedule of limitations on certificate / details repeated on page 5 of this datasheet. mechanical data
bedford opto technology ltd 1,biggar business park, biggar, lanarkshire, ml12 6fx tel: +44 (0) 1899 221221 fax: +44 (0) 1899 221009 website: bot.co.uk e - mail: bill@bot.co.uk absolute maximum ratings (25 o c unless otherwise noted) input diode forward dc current reverse dc voltage power dissipation 100ma 5 volts 165mw (ii) output transistor collector - emitter voltage collector current power dissipation 35 volts 15 ma 165mw (iii) operating temp - 40 o c to +85 o c storage temp - 40 o c to +85 o c input - to - output isolation voltage + 10kv dc (i) notes i) measured with the input leads and output leads shorted together for one min. ii) thermal resistance 375 k/w iii) thermal resistance 450 k/w whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of a reduction in ctr over long periods at high temperatures & currents. packing waffle trays - 100 per tray 290mm x 200mm. tape & reel - 400 devices per 13 diam reel with 7 hub 32mm wide tape. opi 1000l series recommended footprint 2.64 1.32 0.5 18 .7 0 12 .2 0 3.68 15.64 pad centres pb this component is rohs compliant iss p 20.10.12 2/6
advised soldering conditions bedford opto technology ltd 1,biggar business park, biggar, lanarkshire, ml12 6fx tel: +44 (0) 1899 221221 fax: +44 (0) 1899 221009 website: bot.co.uk e - mail: bill@bot.co.uk opi 1000l series pb these components are rohs compliant iss p 20.10.12 3/6
parameter symbol min typ max units test conditions input diode forward voltage v f - - 1.3 v if = 20ma reverse voltage v r 5.0 - - v ir = 100ua output transistor collector - emitter breakdown volt- age bvceo 35 - - v ic = 10 ua collector - emitter leakage current iceo opi1000le opi1000la to d - - 10 100 na na vce = 30 v vce = 10 v emitter - collector breakdown bveco 5.0 - - v ie = 100ua coupled pair dc current transfer ratio i c / i f opi 1000l a - 25 - - % if = 10 ma vce = 5 v opi 1000l b - 50 - - % if = 10 ma vce = 5 v opi 1000l c - 100 - - % if = 10 ma vce = 5 v opi 1000l e - 40 - - % if = 1ma vce = 5 v isolation voltage v iso 10 - - kv - collector - emitter saturation voltage v ce(sat) - - 0.4 v if = 10 ma, ic=1.6ma turn - on time t on - 8 - us ic=2ma turn - off time t off - 8 - us vcc = 5v r l = 100ohm opto electronic data (ta = 25 o c) bedford opto technology ltd 1,biggar business park, biggar, lanarkshire, ml12 6fx tel: +44 (0) 1899 221221 fax: +44 (0) 1899 221009 website: bot.co.uk e - mail: bill@bot.co.uk opi 1000l series pb these components are rohs compliant iss p 20.10.12 4/6
bedford opto technology ltd 1,biggar business park, biggar, lanarkshire, ml12 6fx tel: +44 (0) 1899 221221 fax: +44 (0) 1899 221009 website: bot.co.uk e - mail: bill@bot.co.uk iss p 20.10.12 5/6 opi 1000l series schedule of limitations ec type examination certificate no. bas01atex1278u/5 28th september 2012 schedule of limitations 1 - the opto isolator must be mounted on a p.c.b. havin g a cti of at least 175 such that creepage and clea rance distances are not impaired. i.e.: - on an uncoated printed circuit board that maintain s at least 10mm in air. 2 - the opto isolator may be used to provide isolation b etween either: - (i) a non - intrinsically safe circuit and an intrinsically safe circuit, (non is:is), where the is circuit voltage is not greater than 75 volts peak or d.c.. or (ii) two intrinsically safe circuits (is:is), where the sum of the two circuit voltages is not greater t han 375 volts peak or d.c.. 3 - the opto isolator must be installed such that the c onnection pins are provided with a degree of protectio n of at least ip20 where gasses and vapours may be present. i f the opto isolator is to be installed where dusts re present a hazard, then it must be provided with a degree o f protection of at least ip54 and the overall apparatu s must be appropriately certified for the requirements for dusts. 4 - the opto isolator must be installed with external po wer limiting components as specified in: - en60079 - 11:2012, clause 8.9.2. certificate no.: - iecex bas 06.0021u date of issue: - 2012 - 10 - 02 issue no.: 4 schedule of limitations 1. when used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the opto - isolator: - 2. the opto isolator must be mounted on a printed circ uit board such that creepage and clearance distances are not impaired. 3. the opto coupler must be installed such that the con nection pins are provided with a degree of protection of ip20 where gasses and vapours may be present. if the opto c oupler is to be installed within apparatus where flam ma- ble dusts represent the hazard then it must be provi ded with a degree of protection of ip54 and the appa ratus must be appropriately certified for dust hazards. 5 the opto isolator must be installed with external po wer limiting components as specified in: - iec60079 - 11:2011 ed 6, clause 8.9.2. pb these components are rohs compliant
conformity statement opi1000l series manufacturer: - bedford opto technology ltd address: - 1 biggar business park, market road, biggar, lanarkshire, ml12 6fx, scotland. directive 94/9/ec ec - type examination certificate: - bas01atex1278u C latest supplement bas01atex1278u/ 5 issued sept. 2012 provisions of the directive fulfilled by the component : - ex ia iic ga ( - 40c ta +85c) ii 1 gd ex ia iiic da ( - 40c ta +85c) notified body for ec - type examination & production: - baseefa ltd. C no.1180 baseefa ltd. rockhead business park, staden lane, tel: - +44 (0)1298 766600 buxton, fax: - +44 (0)1298 766601 derbyshire sk17 9rz, e - mail: - info@baseefa.com england harmonised standards used: - en60079 - 0: 2012 en60079 - 11: 2012 en60079 - 26:2007 other standards used: - pb this component is rohs compliant on behalf of bedford opto technology ltd., i declare t hat, the date the component accompanied by this statement is placed on the mark et, the component conforms with all technical and regulatory requirements of the atex directive 94/9/ec and the rohs dirtective 2011/65/eu. _________________________________ mr r.w.stott managing director pp - iss p 20.10.12 6/6 opi 1000l series
|
