View T315HW02-V0_7671335.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 2/27 no reproduction and redistribution allowed document version : 0.0 date : 2008/9/10 product specifications 31.5? fhd color tft-lcd module model name: t315hw02 v0 (*) preliminary specifications () final specifications free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 3/27 no reproduction and redistribution allowed contents no cover contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specifications 4 backlight connector pin configuratio 5 optical specifications 6 mechanical characteristics 7 reliablity 8 international standards 9 packing 10 precautions free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 4/27 no reproduction and redistribution allowed record of revision version date no old description new description remark 0 2007/12/26 first issue free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 5/27 no reproduction and redistribution allowed 1. general description this specification applies to the 31.5 inch color t ft-lcd module t315hw02 v0. this lcd module has a tft active matrix type liquid crystal panel 1920x1080 pixels, and diagonal size of 31.5 inch. this module supports 1920x1080 hdtv mode (non-interlace). each pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pi xel color is determined with a 8-bit gray scale signal for each dot. the t315hw02 v0 has been designed to apply the 8-bi t 1 channel lvds interface method. it is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important. the t315hw02 v0 model is rohs verified which can be distinguished on panel label. * general information items specification unit note active screen size 31.51 inches display area 698.4 (h) x 392.85 (v) mm outline dimension 760.0(h) x 450.0(v) x 45(d) mm with inverter driver element a-si tft active matrix display colors 16.7m colors number of pixels 1920x1080 pixel pixel pitch 0.36375 mm pixel arrangement rgb vertical stripe display mode normally black surface treatment ag, 3h haze = 11 free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 6/27 no reproduction and redistribution allowed 2. absolute maximum ratings the following are maximum values which, if exceeded , may cause permanent damage to the unit. item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 14 [volt] note 1 input voltage of signal vin -0.3 3.6 [volt] note 1 blu input voltage vddb -0.3 28 [volt] note 1 blu brightness control voltage vdim -0.3 7.0 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature pst 65 [ o c] note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no conde nsation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 7/27 no reproduction and redistribution allowed 3. electrical specification the t315hw02 v0 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second input power fo r the blu, is to power inverter.. 3-1 electrical characteristics parameter values min typ max unit notes cd: power supply input voltage vcc 10.8 12 13.2 vdc 1 power supply input current icc - 0.65 0.75 a 2 power consumption pc - 7.8 9 watt 2 inrush current i rush - - 6 apeak 3 differential input high threshold voltage vth 100 mv 4 differential input low threshold voltage vtl 100 mv 4 lvds interface common input voltage vcim 1.10 1.25 1.40 v 4 input high threshold voltage vih (high) 2.4 3.3 vdc cmos interface input low threshold voltage vil (low) 0 0.7 vdc backlight power consumption pddb 63.5 67 70.5 watt life time 50,000 hours 6 note : 1. the ripple voltage should be controlled under 10% o f v cc 2. vcc=12.0v, = v f 60hz, fclk=81.5mhz , 25 , test pattern : white patte rn 3. measurement condition : trush = 470 us 10% 90% vcc gnd free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 8/27 no reproduction and redistribution allowed 4. vcim = 1.2v 5. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, t ft-lcd module have a low luminance and the inverter has ab normal action because leakage current occurs betwee n lamp wire and conducting tape. 6. the relative humidity must not exceed 80% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of c cfl will be reduced. vcim vil 0v vth free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 9/27 no reproduction and redistribution allowed 3-2 interface connections - connector on panel: jae fi-re51s-hf (manufactured by jae) - note: 1. all gnd (ground) pins should be connected together and should also be connected to the lcd?s metal fra me. all vcc (power input) pins should be connected toge ther. 2. for pin 10, 27 and 28, panel will not damage if neg ligently connect these pins to high or low lvds option = high/open, ns mode free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 10/27 no reproduction and redistribution allowed or0 og0 or5 or4 or3 or2 or1 or0 og0 og1 ob1 ob0 og5 og4 og3 og2 og1 ob1 ob2 de vs hs ob5 ob4 ob3 ob2 or6 ob7 ob6 og7 og6 or7 or6 er0 eg0 er5 er4 er3 er2 er1 er0 eg0 eg1 eb1 eb0 eg5 eg4 eg3 eg2 eg1 eb1 eb2 eb5 eb4 eb3 eb2 de er6 eb7 eb6 eg7 eg6 er7 er6 orxclk+ orxclk- orx0 orx1 orx2 orx3 erxclk+ erxclk- erx0 erx1 erx2 erx3 de vs hs or0 og0 or5 or4 or3 or2 or1 or0 og0 og1 ob1 ob0 og5 og4 og3 og2 og1 ob1 ob2 de vs hs ob5 ob4 ob3 ob2 or6 ob7 ob6 og7 og6 or7 or6 er0 eg0 er5 er4 er3 er2 er1 er0 eg0 eg1 eb1 eb0 eg5 eg4 eg3 eg2 eg1 eb1 eb2 eb5 eb4 eb3 eb2 de er6 eb7 eb6 eg7 eg6 er7 er6 orxclk+ orxclk- orx0 orx1 orx2 orx3 erxclk+ erxclk- erx0 erx1 erx2 erx3 de vs hs note: odd data is the first priority. first data is odd. lvds option = low (0v) , jeida mode or2 og2 or7 or6 or5 or4 or3 or2 og2 og3 ob3 ob2 og7 og6 og5 og4 og3 ob3 ob4 de vs hs ob7 ob6 ob5 ob4 or0 ob1 ob0 og1 og0 or1 or0 er2 eg2 er7 er6 er5 er4 er3 er2 eg2 eg3 eb3 eb2 eg7 eg6 eg5 eg4 eg3 eb2 eb4 eb7 eb6 eb5 eb4 de er0 eb1 eb0 eg1 eg0 er1 er0 orxclk+ orxclk- orx0 orx1 orx2 orx3 erxclk+ erxclk- erx0 erx1 erx2 erx3 de vs hs or2 og2 or7 or6 or5 or4 or3 or2 og2 og3 ob3 ob2 og7 og6 og5 og4 og3 ob3 ob4 de vs hs ob7 ob6 ob5 ob4 or0 ob1 ob0 og1 og0 or1 or0 er2 eg2 er7 er6 er5 er4 er3 er2 eg2 eg3 eb3 eb2 eg7 eg6 eg5 eg4 eg3 eb2 eb4 eb7 eb6 eb5 eb4 de er0 eb1 eb0 eg1 eg0 er1 er0 orxclk+ orxclk- orx0 orx1 orx2 orx3 erxclk+ erxclk- erx0 erx1 erx2 erx3 de vs hs free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 11/27 no reproduction and redistribution allowed 4. backlight connector pin configuration - 4-1 electrical specification note1 : vdim= 3.3v (max) ta=255 , turn on for 45minutes note 2 : measurement condition rising time = 20 ms (vddb : 10%~90%); note 3 : (a) uniformity and flicker does not guarantee below 20% dimming control (b) 10% dimming control is function okay and no bac klight shut down 4-2 input specification cn1: ci0114m1hrl-lf (civilux) ; cn2: co042ep1mfa-lf (civilux) free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 12/27 no reproduction and redistribution allowed 4-3 signal timing specifications this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for it?s proper o peration. timing table (de only mode) signal item symbol min. typ. max. unit period tv 1090 1125 1480 th active tdisp(v) 1080 th vertical section blanking tblk (v) 10 45 400 th period th 1030 1100 1300 tclk active tdisp(h) 960 tclk horizontal section blanking tblk (h) 70 140 340 tclk lvds clock frequency fclk (1/tclk) 50 74.25 82 mhz vertical frequency frequency fv 47 60 63 hz horizontal frequency frequency fh 60 67.5 73 khz note : water flow issue need to be confirmed under some frequency 1.) di splay position is specific by the rise of de signal only. horizontal display position is specified by the fal ling edge of 1 st dclk right after the rise of enab, is displayed on the left edge of the screen. vertical display position is specified by the rise of de after a ?low? level period equivalent to eigh t times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise the of enab is displayed at the top line of screen. 3.) if a period of deb ?high? is less than 1920 dcl k or less than 1080 lines, the rest of the screen d isplays black. 4.) the display position does not fit to the screen if a period of de ?high? and the effective data pe riod do not synchronize with each other. free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 13/27 no reproduction and redistribution allowed 4-4 signal timing waveforms free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 14/27 no reproduction and redistribution allowed 4-5 color input data reference the brightness of each primary color (red, green an d blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. th e table below provides a reference for color versus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ------- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 15/27 no reproduction and redistribution allowed 4-6 power sequence for lcd module 4.6.1 power sequence for lcd values parameter min. typ. max. units t1 0.4 --- 30 ms t2 0.1 --- 50 ms t3 300 --- --- ms t4 10 --- --- ms t5 0.1 --- 50 ms t6 --- --- 300 ms t7 500 --- --- s note: the timing controller will not be damaged in cas e of tv set ac input power suddenly shut down. once power reset, it should follow power sequenc e as spec. definition. (1) apply the lamp voltage within the lcd operation ran ge. when the back-light turns on before the lcd ope ration or the lcd turns off before the back-light turns off, the display may momentarily become abnormal screen. free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 16/27 no reproduction and redistribution allowed 4.6.2 power sequence for inverter values parameter min. typ. max. units t1 20 - - ms t2 50 - - ms t3 0 - - ms t4 0 - - ms t5 0 - - ms t6 - - 10 ms free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 17/27 no reproduction and redistribution allowed 5. optical specification optical characteristics are determined after the un it has been ?on? and stable for approximately 45 mi nutes in a dark environment at 25 . the values specified are at an a pproximate distance 50cm from the lcd surface at a viewing angle of and equal to 0. fig.1 1 presents additional information concerning the measurement equipment and method. values parameter symbol min. typ. max. units notes contrast ratio cr 2000 4000 1 surface luminance, white lwh 400 500 cd/ O 2 luminance variation white 9 p 1.30 3 response time g to g t 6.5 ms 4 color gamut ntsc 72 % gamma 2.2 color coordinates red r x 0.64 r y 0.33 green g x 0.29 g y 0.60 blue b x 0.15 b y 0.06 white w x 0.28 w y typ.-0.03 0.29 typ.+0.03 viewing angle x axis, right( =0) r 89 degree 5 x axis, left( =180) l 89 y axis, up( =90) u 89 y axis, down ( =0) d 89 free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 18/27 no reproduction and redistribution allowed note : 1. contrast ratio (cr) is defined mathematically as : surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 acr oss the lcd surface 50cm from the surface with all pixels displaying white. from more information see fig 2. when vddb = 24v, iddb = 5a. l wh =lon1 where lon1 is the luminance with all pixels display ing white at center 1 location. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/ minimum(l on1 , l on2 ,?l on9 ) 4. response time t is the average time required for display transitio n by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness matrix) and i s based on f v =60hz to optimize. 5. viewing angle is the angle at which the contrast ra tio is greater than 10. the angles are determined f or the horizontal or x axis and the vertical or y axis with respect t o the z axis which is normal to the lcd surface. fo r more information see fig4. fig. 2 luminance 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6 free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 19/27 no reproduction and redistribution allowed fig.3 response time the response time is defined as the following figur e and shall be measured by switching the input sign al for ?any level of gray(bright) ? and ?any level of gray(dark)?. any level of gray(bright) any level of gray(dar k) any level of gray(bright) tr r l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 p p p p h h h h o o o o t t t t o o o o d d d d e e e e t t t t e e e e c c c c t t t t o o o o r r r r o o o o u u u u t t t t p p p p u u u u t t t t time time time time l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 l0,15,l31,.l255 fig.4 viewing angle free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 20/27 no reproduction and redistribution allowed 6. mechanical characteristics the contents provide general mechanical characteris tics for the model t315hw02 v0. in addition the fig ures in the next page are detailed mechanical drawing of the lcd. horizontal 760.0mm vertical 450.0mm outline dimension depth 45mm horizontal 703.6mm bezel opening vertical 398.4mm horizontal 698.4mm active display area vertical 392.85mm weight 6500g typ. surface treatment ag, 3h, haze=11% free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 21/27 no reproduction and redistribution allowed front: free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 22/27 no reproduction and redistribution allowed back: free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 23/27 no reproduction and redistribution allowed 7. reliability: environment test condition free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 24/27 no reproduction and redistribution allowed 8. international standard 8-1. safety i. ul1950 third edition, underwriters laboratories, in c. jan. 28, 1995 standard for safety of information technology equip ment including electrical business equipment. ii. can/csa c22.2 no. 950-95/60950 third edition, canad ian standards association, standard for safety of information technology equip ment including electrical business equipment. iii. en60950 : 1992+a2: 1993+a2: 1993+c3: 1995+a4: 1997+ a11: 1997 iec 950: 1991+a1: 1992+a2: 1993+c3: 1995+a4:1996 european committee for electrotechnical standardiza tion (cenelec) european standard for safety of information technol ogy equipment including electrical business equipment. 8-2. emc a) ansi c63.4 ?methods of measurement of radio-noise e missions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 b) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information tec hnology equipment.? international special committee on radi o interference. c) en 55022 ?limits and methods of measurement of radi o interface characteristics of information technology equipment.? european committee for elect rotechnical standardization. (cenelec), 1998 free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 25/27 no reproduction and redistribution allowed 9. packing panel label: tw7a00400044-zm0200 tw7a004: t: taiwan, a/b: china 00044: panel serial number zm0: auo internal code manufactured 07/43: 2007 week 43 made in taiwan: taiwan made carton label: free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 26/27 no reproduction and redistribution allowed 10. precautions please pay attention to the followings when you use this tft lcd module. 10-1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to module. and the case on which a module is mounted should ha ve sufficient strength so that external force is no t transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for th e cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit b reak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers wi th glass, tweezers or anything harder than hb penci l lead. and please do not rub with dust clothes with chemic al treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detriment al to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 10-2 operating precautions (1) the device listed in the product specification shee ts was designed and manufactured for tv application (2) the spike noise causes the mis-operation of circuit s. it should be lower than following voltage: v=200mv(over and under shoot voltage) (3) response time depends on the temperature. (in lower temperature, it becomes longer..) (4) brightness depends on the temperature. (in lower te mperature, it becomes lower.) and in lower temperat ure, response time (required time that brightness is sta ble after turned on) becomes longer. (5) be careful for condensation at sudden temperature c hange. condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (6) when fixed patterns are displayed for a long time, remnant image is likely to occur. (7) module has high frequency circuits. sufficient supp ression to the electromagnetic interference shall b e done by system manufacturers. grounding and shielding me thods may be important to minimize the interface. free datasheet http://www..net/
copyright au optronics, inc. january, 2003 all rights reserved. t315hw02 v0 - spec. ver 0.0 27/27 no reproduction and redistribution allowed 10-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through wrist band etc. and don?t touch interface pin directly. 10-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 10-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the modul e to sunlight or fluorescent light. keep the temper ature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contact wi th any other object. it is recommended that they be stored in the container in which they were shipped. 10-6 handling precautions for protection film (1) the protection film is attached to the bezel with a small masking tape. when the protection film is pe eled off, static electricity is generated between the film an d polarizer. this should be peeled off slowly and c arefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached is st ored for a long time, sometimes there remains a ver y small amount of flue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue remai ns on the bezel or its vestige is recognized, pleas e wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. free datasheet http://www..net/

▲Up To Search▲

Price & Availability of T315HW02-V0

	To Download T315HW02-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .