series am el 1 -az 1 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8.c 1 of 4 north america only features: models single output model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max ( m a) m aximum capacitive load ( f ) efficiency (%) 115 vac 230 vac 277 vac 480 vac amel 1 - 3.3saz 90 - 305/47 - 440 1 3 0 - 430 - 40 to +8 0 3.3 300 2200 70 66 63 amel 1 - 5saz 90 - 305/47 - 440 1 3 0 - 430 - 40 to +8 0 5 200 1100 6 8 64 6 1 amel 1 - 12saz 90 - 305/47 - 440 1 3 0 - 430 - 40 to +8 0 12 83 680 70 66 64 amel 1 - 15saz 90 - 305/47 - 440 1 3 0 - 430 - 40 to +8 0 15 67 560 75 71 68 amel 1 - 24saz 90 - 305/47 - 440 1 3 0 - 430 - 40 to +8 0 24 42 470 78 75 72 amel 1 - 3.3sbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to +8 0 3.3 300 2200 61 60 58 55 amel 1 - 5sbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to +8 0 5 2 00 1100 68 68 66 59 amel 1 - 12sbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to +8 0 12 83 680 70 68 66 57 amel 1 - 15sbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to +8 0 15 67 560 75 76 74 64 amel 1 - 24sbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to +8 0 24 42 470 57 57 56 49 models dual output model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max ( m a) m aximum capacitive load ( f ) efficiency (%) 115 vac 230 vac 277 vac 480 vac amel 1 - 5d az 90 - 305/47 - 440 1 3 0 - 430 - 40 to + 8 0 5 100 1100 6 6 6 7 6 6 amel 1 - 12daz 90 - 305/47 - 440 1 3 0 - 430 - 40 to + 8 0 12 41 680 6 8 6 7 6 6 amel 1 - 15daz 90 - 305/47 - 440 1 3 0 - 430 - 40 to + 8 0 15 33 330 6 4 6 3 6 2 amel 1 - 5dbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to + 8 0 5 100 1100 6 5 6 6 65 57 amel 1 - 12dbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to + 8 0 12 41 680 67 66 65 57 amel 1 - 15dbaz 90 - 528/47 - 440 1 3 0 - 745 - 40 to + 8 0 15 33 330 63 62 61 54 models dual asymmetrical output model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max ( m a) m aximum capacitive load ( f ) efficiency (%) 115 vac 230 vac 277 vac 480 vac amel 1 - 512daz 90 - 305/47 - 440 1 3 0 - 430 - 40 to + 8 0 5/12 65 / 35 1100 5 9 5 9 5 9 amel 1 - 512dbaz 90 - 528 /47 - 440 1 3 0 - 745 - 40 to + 8 0 5/12 65 / 35 1100 58 58 58 50 i nput specifications parameters conditions typical maximum units current (full load) 115 vac 25 ma 230 vac 20 ma 277 vac 1 5 ma 480 vac 1 0 ma inrush current <2ms (cold start) 115 vac 10 a 230 vac 15 a 277 vac 20 a 480 vac 30 a leakage current 0. 15 ma external fuse recommended slow blow type 1 a input dissipation (no load) Q 0. 5 w ? i/o isolation 3000vac ? rohs compliant ? operating temp: - 40 o c to + 80 o c ? input: 90 - 305 vac, 47 - 440hz, or 1 3 0 - 430 vdc ? energy star compliant ? ultra small package ? optional 90 - 528v ac , 47 - 440hz, or 1 3 0 - 745 vdc ? over load , short circuit protection
series am el 1 -az 1 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8.c 2 of 4 north america only single output specifications parameters conditions typical maximum units voltage accuracy full load (typical)* 5 % line regulation ll - hl, full load 5 % load regulation ( single output ) 0 - 100% load (typical)* 5 % transient recovery time 200 s transient response deviation 25% load step 2 % of vout m inimum load 0 % 3.3v& 5v with 680 f (e /c ) 300 mv p - p ripple & noise 12v&15v with 220 uf (e/c) 300 mv p - p 24v with 470 uf (e/c) 200 mv p - p *ripple &noisemeasured at 20mhz bandwidth with 0.1fm/c and 115/230/277/480vac (typical input) with full load . dual output specifications parameters conditions typical maximum units voltage accuracy full load 5 % line regulation ll - hl 5 % load regulation 0 - 100% load 5 % cross regulation 25% load change 5 % transient recovery time 200 s transient response deviation 25% load step 2 % of vout minimum load 0 % ripple & noise 5d/12d/15d with 220 uf (e/c) 200 mv p - p 512d with 220 uf (e/c) 300 mv p - p *ripple &noisemeasured at 20mhz bandwidth with 0.1fm/c and 115/230/277/480vac (typical input ) with full load . * 5d/12d/15d model with symmetric load change and 512d model with asymmetric load change. isolation specifications parameters conditions typical rated units tested i/o voltage 3 0 sec 3 000 vac isolation resistance >1000 m general specifications parameters conditions typical maximum units switching frequency 100 khz over load protection folder back >1 25 % short circuit protection auto recovery operating temperature without derating - 40 to +8 0 o c storage temperature - 40 to + 8 5 o c maximum case temperature 100 o c humidity non condensing 20~95 % rh case material plastic resin + fiberglas s (flammability to ul 94v - 0) weight 2 1 g dimensions (l x w x h) 90 - 305 vac 1.10 x 0.90 x 0.57 inches (28.00 x 23.00 x 14.50 mm) 90 - 528vac 1.10 x 0.90 x 0. 67 inches (28.00 x 23.00 x 17.00 mm) mtbf > 400 000 hrs (mil - hdbk - 217f, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.
series am el 1 -az 1 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8.c 3 of 4 north america only environment approval parameters conditions shock wave form: half sine wave acceleration amplitude: 5gn bump duration: 30 ms number of bumps: 18 (3 in each direction for every axis) converter operation before and after test, body mounted (on chassis) vibrations test mode: sweep sine 10- 100hz, speed 0.05hz/s displacement: 1mm acceleration: 3g 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, ce , cb ( under certification ) , csa information technology equipment iec/ en /ul 60950 - 1:2006+a11:2009 emi - conducted and radiated emission en550 22 , class b harmonic current emissions iec/en 61000 - 3 - 2, (en60555 - 2) voltage fluctuations and flicker iec/en 61000 - 3 - 3, (en60555 - 3) electrostatic discharge immunity iec 61000 - 4 - 2 rf, electromagnetic field immunity iec 61000 - 4 - 3 electrical fast transient/burst immunity iec 61000 - 4 - 4 surge immunity (1kv) iec 61000 - 4 - 5 ( s az &d az:leve l 2 , sbaz &dbaz :level 1 ) rf, conducted disturbance immunity iec 61000 - 4 - 6 power frequency magnetic field immunity iec 61000 - 4 - 8 voltage dips, short interruptions immunity iec 61000 - 4 - 11 canadian safety agency can/csa - c22.2 no. 60950 - 1 - 07 pin out specifications pin single dual 1 nc nc 2 nc nc 3 +v output +v output 4 gnd gnd 5 no pin - v output 6 ac input (l) ac input (l) 7 ac input (n) ac input (n)
series am el 1 -az 1 watt | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r 8.c 4 of 4 north america only dimensions top view amel-s/daz side view dimensions mm (inch) case tolerance ? 0.50 (? 0.02) pin diameter 0.80? 0.05 (0.03? 0.002) pin pitch tolerance ? 0.50 (? 0.02) div: 5.00 (0.20) top view temperature measuring point 28.00 (1.10) 23.00 (0.90) 15.875 (0.625) 3.175 (0.125) 3.175 (0.125) 15.875 (0.625) 6.35 (0.25) 14.50 (0.57) 3.18 (0.13) 0.80 (0.03) 1x 10.0 ( x 0.40) 7 x 0.80 ( x 0.03) 1 2 3 4 5 6 7 1 2 3 4 5 6 7 17.00 (0.69) 3.18 (0.13) 0.80 (0.03) amel-sb/dbaz side view note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other li mited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com.
|
