iec inlet flters fn 9260 general purpose power entry module with fuses approvals n rated currents up to 10a n for one or two fuses n optional medical versions (b type) according to iec/en 60601-1 n snap-in versions (s type) typical applications the fn 9260 power entry module combines an iec inlet, mains filter with excellent filter attenuation and fuses in a small form factor. choosing fn 9260 product line brings you rapid availability of a standard filter associ - ated with the necessary safety acceptances. standard iec connector filters are a practical solution helping you to pass emi system approval in a short time. a wide selection on amperage ratings, output connections, mounting possibilities and filters for medical applications are designed to offer you the desired solution. n exceptional conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior. n b types comply with the requirements of iec/en 60601-1 for creepage and clea- rance, leakage current and high potential testing. n versions up to 10a are available with fuse holder for one or two fuses. n custom-specific versions are available on request. n portable electrical and electronic equipment n medical equipment n small to medium-sized machines and household equipment n single-phase power supplies, switch-mode power supplies n test and measurement equipment features and benefits technical specifications maximum continuous operating voltage: 250vac, 50/60hz operating frequency: dc to 400hz rated currents: 1 to 10a @ 40c max. high potential test voltage: p C> e 2000vac for 2 sec (standard types) p C> e 2500vac for 2 sec (b types) p C> n 760vac for 2 sec (standard types) p C> n 1700vdc for 2 sec (b types) protection category: ip40 according to iec 60529 temperature range (operation and storage): -25c to +85c (25/85/21) design corresponding to: ul 1283, csa 22.2 no. 8 1986, iec/en 60939 flammability corresponding to: ul 94v-2 or better mtbf @ 40c/230v (mil-hb-217f): 2,200,000 hours fuse holder: 1 or 2 fuses (?5 x 20mm) typical electrical schematic n e p line cx r 2xl 2xcy n e p load n e p line cx r 2xl 2xcy n e p load fn 261 fn 9260 (b types without y-capacitors)
> components > fn 9260 * maximum leakage under normal operating conditions. note: if the neutral line is interrupted, worst case leakage could reach twice this level. filter selection table fn 9260x-1-06-y 1 (1.2) 373 5.3 0.1 2.2 1000 -06 2 55 fn 9260x-2-06-y 2 (2.3) 373 2.7 0.1 2.2 1000 -06 2 55 fn 9260x-4-06-y 4 (4.6) 373 1.0 0.1 2.2 1000 -06 2 55 fn 9260x-6-06-y 6 (6.9) 373 0.3 0.1 2.2 1000 -06 2 55 fn 9260x-10-06-y 10 (11.5) 373 0.2 0.1 2.2 1000 -06 2 55 fn 9260xb-1-06-y 1 (1.2) 2 5.3 0.1 1000 -06 2 55 fn 9260xb-2-06-y 2 (2.3) 2 2.7 0.1 1000 -06 2 55 fn 9260xb-4-06-y 4 (4.6) 2 1.0 0.1 1000 -06 2 55 fn 9260xb-6-06-y 6 (6.9) 2 0.3 0.1 1000 -06 2 55 fn 9260xb-10-06-y 10 (11.5) 2 0.2 0.1 1000 -06 2 55 fn 261x-1-06-y 1 (1.2) 373 5.3 0.1 2.2 1000 -06 1 55 fn 261x-2-06-y 2 (2.3) 373 2.7 0.1 2.2 1000 -06 1 55 fn 261x-4-06-y 4 (4.6) 373 1.0 0.1 2.2 1000 -06 1 55 fn 261x-6-06-y 6 (6.9) 373 0.3 0.1 2.2 1000 -06 1 55 fn 261x-10-06-y 10 (11.5) 373 0.2 0.1 2.2 1000 -06 1 55 filter rated current leakage current* inductance capacitance resistance input/output fuses weight @ 40c (25c) @ 230vac/50hz l cx cy r connections [a] [a] [mh] [f] [nf] [k?] [qty] [g] for example: fn 9260-1-06-10, fn 9260sb-10-06-20, fn 261s-6-06-30 product selector fn 9260xx-yy-yy-y snap-in range for s version only 10: snap-in range 0.6 to 1.5mm 20: snap-in range 1.6 to 2.5mm 30: snap-in range 2.6 to 3.5mm 06: faston 6.3 x 0.8mm (spade/soldering) 1 to 10: rated current blank: standard version b: medical version (wihtout y-capacitor) blank: standard housing with mounting fanges s: snap-in version, snapper on vertical side per cispr 17; a = 50 ? /50 ? sym; b = 50 ? /50 ? asym; c = 0.1 ? /100 ? sym; d = 100 ? /0.1 ? sym typical filter attenuation fn 9260: 1 to 4a types fn 9260: 6 and 10a types fn 261: 1 to 4a types fn 261: 6 and 10a types
> components > fn 9260 mechanical data fn 9260 / fn 261 fn 9260s / fn 261s panel cut out installation a c b e h g s f d i 6.3 x 0.8 j a b e g f d i j 6.3 x 0.8 n r m p c t fn 9260 fn 9260s tolerances fn 261 fn 261s dimensions a 46 34 0.3 b 35 35 0.3 c 36 0.3 d 41 41 0.3 e 27.8 27.8 +0.3/-0 f 5.5 5.5 0.3 g 32 32 +0.3/-0 h ?3.2 0.1 i 13.8 13.8 j 12.5 12.5 0.3 m r 3.5 r 3.5 n 33 33 +0.3/-0 p 29 29.5 0.3 r m3 s 90 t* 0.6 - 1.5 t* 1.6 - 2.5 t* 2.6 - 3.5 * for selecting the panel thickness, please refer to the filter selector table. all dimensions in mm; 1 inch = 25.4mm tolerances according: iso 2768-m / en 22768-m your local partner: to find your local partner within schaffners global network, please go to www.schaffner.com february 2009
|