intellimod? l1-series three phase igbt inverter + brake 25 amperes/1200 volts PM25RL1C120 1 powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 04/130 rev. 2 description: powerex intellimod? intelligent power modules are isolated base modules designed for power switching applications operating at frequencies to 20khz. built-in control circuits provide optimum gate drive and protection for the igbt and free-wheel diode power devices. features: complete output power circuit gate drive circuit protection logic C short circuit C over temperature using on-chip temperature sensing C under voltage low loss using full gate cstbt ? igbt chip applications: inverters ups motion/servo control power supplies ordering information: example: select the complete part number from the table below -i.e. PM25RL1C120 is a 1200v, 25 ampere intellimod? intelligent power module. type current rating v ces amperes volts (x 10) pm 25 120 dim. inches millimeters a 3.54 90.0 b 1.97 50.0 c 0.98 25.0 d 3.5 80.0 e 0.2 5.0 f 0.4 10.0 g 0.08 2.0 h 0.17 dia. 4.3 dia. j 0.8 20.5 k 0.9 23.0 l 0.47 12.0 m 0.012 0.3 dim. inches millimeters n 0.58 14.6 p 0.26 6.7 q 0.02 0.5 r 0.56 14.2 s 0.1 0.02 2.5 0.5 t 0.31 8.0 u 0.02 sq. 0.5 sq. v 0.08 2.0 w 0.69 0.02 17.5 0.5 x 2.20 55.0 y 0.52 13.0 z 0.65 16.5 outline drawing and circuit diagram a d e f f f f g g g g g g g g g g g g g b c g n p m q k j l l l l l f t s w x v y z c u (19 typ.) r h (2 typ.) 1 5 9 13 b p n u v w 19 f o 17 v n 14 v n1 11 w p 8 v vp1 2 u fo 6 v fo 5 v vpc 3 u p 7 v p 9 v wpc 10 w fo 12 v wp1 1 v upc 4 v up1 16 u n 15 br 18 w n 13 v nc terminal code v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot p u br 1.5k 1.5k 1.5k 1.5k v w n b v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot u n f o v nc w n v n1 v n v wpc w p w fo v wp1 v vpc v p v fo v vp1 v upc u p u fo v up1
PM25RL1C120 intellimod? l1-series three phase igbt inverter + brake 25 amperes/1200 volts 2 powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 04/13 rev. 2 absolute maximum ratings, t j = 25c unless otherwise specifed characteristics symbol PM25RL1C120 units power device junction temperature t j -20 to 150 c storage temperature t stg -40 to 125 c mounting torque, m4 mounting screws 15 in-lb module weight (typical) 150 grams supply voltage, surge (applied between p - n) v cc(surge) 1000 volts self-protection supply voltage limit (short circuit protection capability)* v cc(prot.) 800 volts isolation voltage, ac 1 minute, 60hz sinusoidal v iso 2500 volts igbt inverter sector collector-emitter voltage (v d = 15v, v cin = 15v) v ces 1200 volts collector current (t c = 25c) (note 1) i c 25 amperes peak collector current (t c = 25c) i cp 50 amperes collector dissipation (t c = 25c) (note 1) p c 178 watts igbt brake sector collector-emitter voltage (v d = 15v, v cin = 15v) v ces 1200 volts collector current (t c = 25c) (note 1) i c 25 amperes peak collector current (t c = 25c) i cp 50 amperes collector dissipation (t c = 25c) (note 1) p c 178 watts diode forward current (t c = 25c) i f 25 amperes diode rated dc reverse voltage (t c = 25c) v r(dc) 1200 volts control sector supply voltage (applied between v up1 -v upc , v vp1 -v vpc , v wp1 -v wpc , v n1 -v nc ) v d 20 volts input voltage (applied between u p -v upc , v p -v vpc , w p -v wpc , u n - v n - w n -br-v nc ) v cin 20 volts fault output supply voltage v fo 20 volts (applied between u fo -v upc , v fo -v vpc , w fo -v wpc , f o -v nc ) fault output current (u fo , v fo , w fo , f o terminals) i fo 20 ma *vd = 13.5 ~ 16.5v, inverter part, t j = 125c arm up vp wp un vn wn br axis igbt fwdi igbt fwdi igbt fwdi igbt fwdi igbt fwdi igbt fwdi igbt fwdi x 49.0 49.0 35.0 35.0 21.0 21.0 42.0 42.0 28.0 28.0 14.0 14.0 64.0 67.8 y 2.4 -4.4 2.4 -4.4 2.4 -4.4 -6.9 -0.05 -6.9 -0.05 -4.9 2.0 4.3 -4.6 bottom view y x (0,0) note 1:t c (under the chip) measurement point
PM25RL1C120 intellimod? l1-series three phase igbt inverter + brake 25 amperes/1200 volts 3 powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 04/13 rev. 2 electrical and mechanical characteristics, t j = 25c unless otherwise specifed characteristics symbol test conditions min. typ. max. units igbt inverter sector collector-emitter saturation voltage v ce(sat) v d = 15v, v cin = 0v, i c = 25a, 1.55 volts t j = 25c v d = 15v, v cin = 0v, i c = 25a, 1.75 volts t j = 125c diode forward voltage v ec -i c = 25a, v cin = 15v, v d = 15v 2.3 volts inductive load switching times t on 1.0 s t rr v d = 15v, v cin = 0 ? 15v 0.5 s t c(on) v cc = 600v, i c = 25a 0.4 s t off t j = 125c 2.0 s t c(off) 0.7 s collector-emitter cutoff current i ces v ce = v ces , v d = 15v, t j = 25c 1.0 ma v ce = v ces , v d = 15v, t j = 125c 10 ma igbt brake sector collector-emitter saturation voltage v ce(sat) v d = 15v, v cin = 0v, i c = 25a, 1.55 volts t j = 25c v d = 15v, v cin = 0v, i c = 25a, 1.75 volts t j = 125c forward voltage v fm i f = 25a 2.3 volts collector-emitter cutoff current i ces v ce = v ces , v d = 15v, t j = 25c 1.0 ma v ce = v ces , v d = 15v, t j = 125c 10 ma control sector circuit current i d v d = 15v, v cin = 15v, v n1 -v nc 20 30 ma v d = 15v, v cin = 15v, v *p1 -v *pc 5 10 ma input on threshold voltage v th(on) applied between u p -v upc , 1.2 1.5 1.8 volts input off threshold voltage v th(off) v p -v vpc , w p -v wpc , u n - v n - w n -br-v nc 1.7 2.0 2.3 volts short circuit trip level sc inverter part 50 amperes (-20c t j 125c, v d = 15v) brake part 50 amperes short circuit current delay time t off(sc) v d = 15v 0.2 s over temperature protection ot trip level 135 145 c (detect t j of igbt chip) ot r reset level 125 c supply circuit under-voltage protection uv trip level 11.5 12.0 12.5 volts (-20 t j 125c) uv r reset level 12.0 12.5 13.0 volts fault output current* i fo(h) v d = 15v, v cin = 15v 0.01 ma i fo(l) v d = 15v, v cin = 15v 10 15 ma minimum fault output pulse width* t fo v d = 15v 1.0 1.8 ms *fault output is given only when the internal sc, ot and uv protections schemes of either upper or lower arm device operates to protect it.
PM25RL1C120 intellimod? l1-series three phase igbt inverter + brake 25 amperes/1200 volts 4 powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 04/13 rev. 2 electrical and mechanical characteristics, t j = 25c unless otherwise specifed characteristics symbol test conditions min. typ. max. units thermal characteristics, t j = 25c unless otherwise specifed characteristic symbol condition min. typ. max. units junction to case thermal resistance r th(j-c)q igbt (per 1 element) (note 1) 0.70* c/watt inverter part r th(j-c)d fwdi (per 1 element) (note 1) 1.18* c/watt junction to case thermal resistance r th(j-c)q igbt (note 1) 0.70* c/watt brake part r th(j-c)d fwdi (note 1) 1.18* c/watt contact thermal resistance r th(c-f) case to fin per module, 0.085 c/watt thermal grease applied) (note 1) recommended conditions for use characteristic symbol condition value units supply voltage v cc applied across p-n terminals 800 volts control supply voltage** v d applied between v up1 -v upc , 15.0 1.5 volts v vp1 -v vpc , v wp1 -v wpc , v n1 -v nc input on voltage v cin(on) applied between u p -v upc , 0.8 volts input off voltage v cin(off) v p -v vpc , w p -v wpc , u n - v n - w n -br-v nc 9.0 volts pwm input frequency f pwm 20 khz arm shoot-through blocking time t dead input signal 2.5 s * if you use this value, r th(f-a) should be measured just under the chips. ** with ripple satisfying the following conditions: dv/dt swing 5v/s, variation 2v peak to peak.
|