he3 www.vishay.com vishay revision: 07-mar-13 1 document number: 42089 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 wet tantalum capacitors, high energy, ultra high capacitance, - 55 c to + 125 c operation features ? high energy, very high capacitance design ? all tantalum, hermetically sealed case ? utilizes vishay proven supertan ? technology ? terminations: radial leaded ? approved to dscc drawing 10011 ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 note * lead (pb)-containing terminations are not rohs-compliant. exemptions may apply. applications ? industrial ? avionics/military/space performance characteristics operating temperature: - 55 c to + 85 c (to + 125 c with voltage derating) capacitance tolerance: at 120 hz, + 25 c 20 % standard 10 % available as special contact marketing for availa bility of 10 % tolerance dc leakage current (dcl max.): at + 25 c: leakage current shall not exceed the values listed in the standard ratings tables. life test: capacitors are capable of withstanding a 1000 h life test at a temperature of + 85 c at th e applicable rated dc working voltage. note (1) contact marketing for availability of 10 % tolerance ordering information he3 c 543 k 025 b z s s type case code capacitance capacitance tolerance dc voltage rating at + 85 c termination and packaging reliability level temperature esr see ratings and case codes table this is expressed in microfarads. the first two digits are the significant figures. the third is the number of zeros to follow. k = 10 % (1) m = 20 % this is expressed in v. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an r (6r3 = 6.3 v) a = 100 % tin (rohs compliant) b = tin/lead and bulk z = non-er s = standard (- 55 c to + 85 c) s = standard
he3 www.vishay.com vishay revision: 07-mar-13 2 document number: 42089 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions in inches [millimeters] case code dheight l2 (min.) l1 (min.) t weight (g) (typical) type he3 a 1.400 0.005 [35.56 0.127] 0.350 0.015 [8.89 0.381] 0.500 [12.70] 0.500 [12.70] 0.40 0.015 [10.2 0.38] 48.0 b 1.400 0.005 [35.56 0.127] 0.488 0.015 [12.395 0.381] 0.500 [12.70] 0.500 [12.70] 0.40 0.015 [10.2 0.38] 73.0 c 1.400 0.005 [35.56 0.127] 0.615 0.015 [15.6 0.4] 0.500 [12.70] 0.500 [12.70] 0.40 0.015 [10.2 0.38] 95.0 standard ratings capacitance (f) case code part number max. esr at + 25 c, 1 khz ( ? ) max. dcl at + 25 c (a) 25 v dc at + 85 c; 15 v dc at + 125 c 18 000 a he3a183(1)025(2)(3)(4)(5) 0.060 150 24 000 a he3a243(1)025(2)(3)(4)(5) 0.060 150 36 000 b he3b363(1)025(2)(3)(4)(5) 0.045 200 48 000 b he3b483(1)025(2)(3)(4)(5) 0.045 200 54 000 c he3c543(1)025(2)(3)(4)(5) 0.035 300 72 000 c he3c723(1)025(2)(3)(4)(5) 0.035 350 50 v dc at + 85 c; 30 v dc at + 125 c 8000 a he3a802(1)050(2)(3)(4)(5) 0.075 170 16 000 b he3b163(1)050(2)(3)(4)(5) 0.045 270 24 000 c he3c243(1)050(2)(3)(4)(5) 0.035 400 63 v dc at + 85 c; 40 v dc at + 125 c 4000 a he3a402(1)063(2)(3)(4)(5) 0.100 170 8000 b he3b802(1)063(2)(3)(4)(5) 0.055 270 12 000 c he3c123(1)063(2)(3)(4)(5) 0.035 400 80 v dc at + 85 c; 50 v dc at + 125 c 3000 a he3a302(1)080(2)(3)(4)(5) 0.100 300 6000 b he3b602(1)080(2)(3)(4)(5) 0.065 400 9000 c he3c902(1)080(2)(3)(4)(5) 0.040 500 100 v dc at + 85 c; 65 v dc at + 125 c 1900 a he3a192(1)100(2)(3)(4)(5) 0.085 300 3800 b he3b382(1)100(2)(3)(4)(5) 0.065 400 5700 c he3c572(1)100(2)(3)(4)(5) 0.050 500 125 v dc at + 85 c; 85 v dc at + 125 c 1100 a he3a112(1)125(2)(3)(4)(5) 0.100 300 2200 b he3b222(1)125(2)(3)(4)(5) 0.085 400 3300 c he3c332(1)125(2)(3)(4)(5) 0.075 500 note ? part number definitions: (1) standard capacitance tolerance is 20 % or m. contact marketing for availability of 10 % or k. (2) standard termination is b or tin/lead. ro hs compliant or 100 % ti n is available as a. (3) standard reliability is z or non-established reliability. (4) standard temperat ure range is s or - 55 c to + 125 c. (5) standard esr is s. d positive lead l2 h l1 t 0.0253 0.002 [0.64 0.05] dia. (no. 22 awg) tinned nickel leads solderable and weldable negative lead (attached to case) 0.156 max..
he3 www.vishay.com vishay revision: 07-mar-13 3 document number: 42089 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 performance characteristics of high energy capacitors electrical performance characteristics item performance characteristics operating temperature range - 55 c to + 85 c (to + 125 c with voltage derating) storage temp erature range - 62 c to + 130 c capacitor tolerance 20 % 10 % at 120 hz esr limits per standa rd ratings table dc leakage current (dcl max.) at 25 c the leakage current shall not exceed values listed in the standard rating table. reverse voltage no continuous reverse voltage permitted surge voltage the test shall be at 1000 cycles at 110 % of rated voltage at 85 c. a cycle consists of a 30 s charge and a 330 s di scharge through 100 ? resistor. life test at + 85 c 1000 h at + 85 c environmental characteristics item test and conditions comments hermeticity mil-std-202, method 112 c/iiia the capacitor shall be hermetically sealed such that the case does not leak electrolyte or vent any gas when exposed to a vacuum. moisture resistance mil-std- 202, method 106 6 v polarity altitude mil-std-202, method 105 c, test condition d 100 000 feet test mechanical performance characteristics item test and conditions comments thermal shock mil-std-202, me thod 107 g test condition a shock mil-std-202, method 213 b test condition g 11 ms, 50 g vibration - hi gh frequency mil-std-202, method 204 d test condition d 12 sweeps/axis, 20 g peak vibration - random mil-std-202, method 214 a test condition i, letter d 1.5 h/axis, 12 g resistance to solder heat mil-std-202, method 210 f the capacitor must withstand solder dipping of the terminals at 260 c for 10 s. the capacitor must not be visibly damaged and the electrical characteristics must not be affected. solderability mil-std-202, method 208 terminal strength mil- std-202, method 211 a the capacitor terminals must withstand a 5 pound pull test for 5 s to 10 s. the capacitor must not be visi bly damaged and the electrical characteristics must not be affected. part markings mil-std-202, method 215 j the capacitor shall be permanently and legibly marked on the circumference of the case. the markings shall be resistant to solvents. weight (mass) see dimensions table
he3 www.vishay.com vishay revision: 07-mar-13 4 document number: 42089 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 he3 mounting options the he3 capacitor can be mounted with ma ny commercially available me thods. vishay offers the optional mounting hardware outlined below. through-hole if mounted through-hole, the glass-to-metal seal must be protected from potentia l mounting and application stress. the he3 can be mounted termination down through the he3spc001 space r into the pcb. the proper si ze bracket he3bkt00* can then be utilized to hold the he3 rigidly to the pcb. terminations up if mounted with terminations facing up for attachment to wiring, the spacer is not needed. the he3 can be reverse with terminations facing upward through the center of the he 3bkt00* bracket, which is then mounted through the pcb. notes ? spot weld, 2 places ? mounting bolt: 1. material - stainless steel 2. thread - 6-32 nc-2a note (1) the part numbers shown are for ordering th e mounting bracket and/or spacer. the he3 ca pacitor must be orde red separately using the correct part number as outlined in ordering information and in the standard ratings table. part number (1) stud a 0.010 he3bkt001 he3a 0.391 he3bkt002 he3b 0.518 he3bkt003 he3c 0.605 he3bkt004 he3a w/spacer 0.572 he3bkt005 he3b w/spacer 0.699 he3bkt006 he3c w/spacer 0.831 he3 nickel hold down cup m s -he-04-003 he hold down s tud m s -c-17-315-1 a 0.789 1.579
he3 www.vishay.com vishay revision: 07-mar-13 5 document number: 42089 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) the part numbers shown are for ordering th e mounting bracket and/or spacer. the he3 ca pacitor must be orde red separately using the correct part number as outlined in ordering information and in the standard ratings table. he3 pc board mounted part number (1) he3spc001 1.150 dia. 1.326 0.002 dia. 1.400 dia. 0.195 0.015 note mat. l: aluminum bracket bracket he3 he3 s pacer
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
