View 41713002X-3_8036365.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 dvi-d interface controller for 2560x1600 resolution tft panel model: dvi-2560 part number : 41713002X-3 instructions contents page: 2. introduction, how to proceed, usage note, disclaimer 2. system design ? diagram of a suggested system 3. assembly notes ? important information about system elements 5. connection & operation ? how to use the controller 7. connectors, pinouts & jumpers ? essential connection information 11. controller dimensions 12. application notes 13. troubleshooting 14 specifications 15 appendix i ? graphic mode support table 16. warranty, caution & limitation of liability, trademarks 17. contact details it is essential that these instructions are read and understood before connecting or powering up this controller.
2 introduction designed for 2560x1600 lcd monitor applications, the dvi-2560 c ontroller provides easy to use interface controller for: ? tft (active matrix) lcds with tmds interface of 2560x1600 resolution panel model support : 1. lg lm300w01-a3 2. samsung ltb300m1-p01 3. samsung ltm300m1-p01 ? dvi-d input signals of wqxga (2560x1600 60hz) standard how to proceed ? ensure you have all parts & that they are correct, refer to: ? connection diagram (separat e document for each panel) ? connector reference (in following section) ? assembly notes ? check controller switch & jumper settings (errors may damage the panel) ? prepare the pc ? connect the parts ? understand the operation and functions (in following section) important usage note this product is for use by system developers and integrat ors, the manufacturer accepts no liability for damage or injury caused by the use of this produc t. it is the responsibility of the developer , integrators or other user of this product to: ? ensure that all necessary and appropriate safety measures are taken. ? obtain suitable regulatory approvals as may be required. ? check power settings to all component parts before connection. ? understand the operation and connectivity requirements of this controller. disclaimer there is no implied or expressed warranty regarding this material. system design a typical lcd based display system utilising this controller is likely to comprise the following: summary: 1. lcd 2560x1600 resolution panel 2. lcd controller card, dvi-2560 3. tmds cable 4. panel power and control signal cable 5. inverter cable 6. function controls 7. function controls cable 8. source detect led 9. backlight status led 10. dvi-d input 11. power input (24vdc) digital view offers a range of accessories such as listed above, to make up complete display solution.
3 assembly notes this controller is designed for monito r and custom display projects usi ng 2560x1600 resolution tft panels with wqxga (2560x1600 60hz) signal input. the following provides some guide lines for installation and prepar ation of a finished display solution. preparation : before proceeding it is important to familiarize your self with the parts making up the system and the various connectors, mounting holes and general layout of the controller. as much as possible connectors hav e been labeled. guides to connectors and mounting hol es are shown in the following relevant sections. 1. lcd panel : this controller is designed for typical tmds interfac e tft panels with panel voltage 18v. due to the variation between manufacturers of signal timing and other panel characteristics factory setup and confirmation should be obtained before connecting to a panel. (note: check panel power jumper settings before connection) 2. controller card: handle the controller card with care as static charge may damage electronic components. 3. tmds signal cable : in order to provide a clean signal it is reco mmended that tmds signal c ables are no longer than 46cm (18 inches). if loose wire cabling is utilized these can be made into a harness with cable ties. care should be taken when placing the cables to avoi d signal interference. additionally it may be necessary in some systems to add ferrite cores to the cables to minimize signal noise. 4. panel power and control signal cable : this cable provides panel power and control signal for the panel. if loose wire cabling is utilized these can be made into a harness with cabl e ties. care should be taken when placing the cables to avoid signal interference. additionally it may be necessary in so me systems to add ferrite cores to the cables to minimize signal noise. 5. inverter cables : different inverter models require different cables and different pin a ssignment. make sure correct cable pin out to match the inverter. using wrong cable pin out may damage the inverter. 6. function controls : the following section discusses the controls r equired and the section on c onnectors provides the detail. the controls are minimal: on/o ff, backlight brightness (depends on inverter). 7. function controls cable : the cables to the function switches should be of suitable quality and length so that impedance does not affect performance. generally lengths up to 1 metre (3 feet) should be acceptable. 8. source detect led (led1a) : this led shows the input source detected stat us. it will gives green color for signal detected and red color for signa l not detected. 9. backlight status led (led2a) : this led shows the backlight status. it will gives green co lor indicated for normal backlight status and red color indicated for not normal backlight status. 10. dvi-d input cable : plug the dvi cable to the connec tor p1 on the controller board 11. power input : 24v dc is required, this should be a regulated supply. although the contro ller provides power regulation for the lcd power this does not relate to the power supplied to the backlight inverter. if an unregulated power supply is provided to an inverter any fluctuations in power may affe ct operation, performance and lifetime of the inverter and or backlight tubes. ? power safety : note that although only 24vdc is s upplied as ?power-in? a backlight inverter for panel backlighting produces significantly higher voltages (t he inverter does not connect to the ground plane). we strongly advise appropriate insulation for all circuitry. ? emi : shielding will be required for passing certain regulatory emissions tests. also the choice of external controller to pc signal cable can affect the result. ? ground : the various pcb mounting holes are connected to the ground plane. ? servicing : the board is not user serviceable or repairable. warranty does not cover user error in connecting up to the controller and is invalidated by unaut horized modification or repairs. ? controller mounting : it is recommended that a clearance of at l east 10mm is provided above and 5mm below the controller when mounted. additionally consideration s hould be given to: ? electrical insulation. ? grounding. ? emi shielding. ? cable management. note: it is important to keep panel signal cables apart from the invert er & backlight cables to prevent signal interference. ? heat & ventilation: heat generated from other sources, fo r example the backlight of a very high brightness panel may generate significant heat which could adversely affect the controller. ? other issues that may affect safety or performance.
4 ? pc graphics output : a few guidelines: ? signal quality is very important, if there is noise or instab ility in the pc graphics output this may result in visible noise on the display. ? refer to graphics modes table in spec ifications section for supported modes. important: please read the application notes section for more information.
5 connection & operation caution: never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. connection connection and usage is quite straight forward (it is useful to have the relevant connec tion diagram available at this time): 1. lcd panel : this controller only support 18v 2560x1600 reso lution panel model ? lg lm300w01-a3, samsung ltb300m1-p01 and samsung ltm300m1-p01. 2. tmds panel cable connection : plug the tmds signal cable direct to cn1 . insert the panel end of the cable to the lcd panel connector. 3. panel power and control signal connection : plug the panel power and control signal cable direct to cn2. insert the panel end of the cable to the lcd panel connector. 4. inverter & controller: plug the inverter cable to cna1, cnb1 and cnb2. plug another end to the connector on the panel built-in inverter. 5. function switch & controller: plug the osd switch mount cable to cnc1 on the controller board and another to the osd switch mount. 6. led & controller: plug in a 3-way with dual colour led to connector led1a & led2a on the controller board. 7. jumpers : check all jumpers are set correctly. details referring the connection diagram at http://www.digitalview.com/controllers/csg.php 8. jumpers & inverter & panel voltage: particularly pay attention to the settings of jb1, jb2, jb3. jb1 is used for setting the backlight brightness control voltage range on specif ic inverter. jb2 & jb3 are used for inverter control (read inverter specification and information on the jumper tabl e to define the correct settings). this controller is now always to default output 18v panel power. 8. dvi-d cable : plug the dvi cable to the connec tor p1 on the controller board. 9. power supply & controller: plug the dc 24v power in to the connector pp2 . you can consider to use digitalview mating power cable p/n 426013700-3, 160mm. 10. power on: switch on the controller board and panel by using the osd switch mount. caution : never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. general: ? if you are using supplied cables & accessories, ensure they are correct for the model of panel and controller. ? if you are making your own cables & connec tors refer carefully to both the panel & inverter specifications and the section in this manual, ?connectors, pinouts & jumpers? to ensure the correct pin to pin wiring. pc settings the controller has been designed to support dvi 2560x1600 60h z mode coming from graphics display card only. operation the controller can allow you to switch on/off the board and controlling the backlight brightness via osd switch mount.
6 lcd display system settings note: by way of explanation the following refers to a set of sample buttons on the osd switch mount that may be obtained as an option controls analog vr type digital type on/off ? turns controller board power on vr toggle switch on/off button brightness ? controls backlight brightne ss rotary vr brightness +/- buttons ** ?menu?, ?sel up?, ?sel dn?, ?+?, ?-? keys are all no function. on/off/brightness sel up sel dn + - menu analog vr type digital type
7 connectors, pinouts & jumpers the various connectors are: summary: connectors ref purpose description cn1 tmds panel signal hirose 30-pin, df13-30dp-1. 25 (mating type : df13-30ds-1.25c) cn2 panel power and control signal hirose 20-pin, df13- 20dp-1.25 (mating type : df13-20ds-1.25c) cna1 auxiliary power output jst 4-way, b4b-xh-a (mating type : xhp-4) cnb1 backlight inverter jst 8-way, b8b-xh-a (mating type : xhp-8) cnb2 backlight inverter jst 2-way, b2b-xh-a (mating type : xhp-2) cnc1 function controls jst 12-way, b12b-xh-a (mating type : xhp-12) led1a source detected led header pin 3x1 led2a backlight status led header pin 3x1 p1 dvi-d signal input dvi-d connector pp2 power input molex 43045-0400 compatible (matching connector type : molex 43025-0400 compatible) (matching power cable : p/n 426013700-3)
8 summary: jumpers setting ref purpose note ja1 on board +5v power enable 1-2 & 3-4 closed, factory set, do not remove ja2 panel power 1-2 & 3-4 closed, factory set, do not remove jb1 backlight brightness control voltage range 1-2 closed = 3.3v max 2-3 closed = 2.8v max jb2 backlight inverter on/off control ? signal le vel 1-2 = on/off control signal ?high? = +5v 2-3 = on/off control signal ?high? = +3.3v open = on/off control signal ?high? = open collector caution : incorrect setting can damage inverter. jb3 backlight inverter on/off control ? polar ity 1-2 = control signal ?high? = ccft on 2-3 = control signal ?low? = ccft on jb6 backlight status 1-2 & 3-4 clos ed = backlight status low = normal 1-3 & 2-4 closed = backlight status high = normal open = backlight status not used jp6 input power control short = external switch control open = switch mount control led1a ? source detected led status : source detected state led color detected green not detected red led2a ? backlight status led status : backlight status state led color normal green not normal red
9 cn1 ? panel connector: hirose df13-30dp-1.25 (matching type : hirose df13-30ds-1.25c) pin symbol description 1 gnd ground 2 gnd ground 3 rx0+ tmds positive differential output (channel 0) 4 rx0- tmds negative differential output (channel 0) 5 gnd ground 6 gnd ground 7 rx1+ tmds positive differential output (channel 1) 8 rx1- tmds negative differential output (channel 1) 9 gnd ground 10 gnd ground 11 rx2+ tmds positive differential output (channel 2) 12 rx2- tmds negative differential output (channel 2) 13 gnd ground 14 gnd ground 15 rx3+ tmds positive differential output (channel 3) 16 rx3- tmds negative differential output (channel 3) 17 gnd ground 18 gnd ground 19 rx4+ tmds positive differential output (channel 4) 20 rx4- tmds negative differential output (channel 4) 21 gnd ground 22 gnd ground 23 rx5+ tmds positive differential output (channel 5) 24 rx5- tmds negative differential output (channel 5) 25 gnd ground 26 gnd ground 27 rxc+ tmds positive differential output (channel c) 28 rxc- tmds negative differential output (channel c) 29 gnd ground 30 gnd ground cn2 ? panel connector: hirose df13-20dp-1.25 (matching type : hirose df13-20ds-1.25c) pin symbol description 1 phsync h-sync from panel 2 pvsync v-sync from panel 3 lcm_on panel power on signal 4 nc no connection 5 gnd ground 6 gnd ground 7 vlcd panel power 8 gnd ground 9 vlcd panel power 10 vlcd panel power 11 vlcd panel power 12 vlcd panel power 13 gnd ground 14 gnd ground 15 gnd ground 16 nc no connection 17 nc no connection 18 nc no connection 19 nc no connection 20 nc no connection cna1 - auxiliary power output: jst b4b-xh-a (matching type : xhp-4) pin symbol description 1 24va +24v dc, 2a max 2 gnd ground 3 gnd ground 4 5v +5v dc, 500ma max cnb1 ? backlight inverter connector: jst b5b-xh-a (matching type : xhp-5) pin symbol description 1 24va backlight power supply, +24vdc 2 24va backlight power supply, +24vdc 3 gnd ground 4 gnd ground 5 24va backlight power supply, +24vdc 6 blctrl backlight on/off control signal (refer to jb2 & jb3) 7 bvr_wip backlight brightness vr pin wip 8 bvr_a backlight brightness vr pin a
10 cnb2 - auxiliary power output: jst b2b-xh-a (matching type : xhp-2) pin symbol description 1 bl_status backlight status 2 gnd ground cnc1 ? control switch, jst b12b-xh-a pin symbol description 1 pswin power button a 2 sw_on power button b 3 bvr_a backlight brightness vr pin a 4 bvr_wip backlight brightness r pin wip 5 bvr_b backlight brightness vr pin b (470 ohm resistor to +5v vcc) 6 gnd ground 7 nc no connection 8 nc no connection 9 nc no connection 10 nc no connection 11 nc no connection 12 nc no connection led1a ? source detected led, header pin 3x1 pin description 1 red led pin (anode) 2 led pin common (cathode) 3 green led pin (anode) led2a ? backlight status led, header pin 3x1 pin description 1 red led pin (anode) 2 led pin common (cathode) 3 green led pin (anode) p1 ? dvi-d input pin symbol description 1 /rx2 tmds data 2- 2 rx2 tmds data 2+ 3 gnd digital ground 4 nc no connection 5 nc no connection 6 dvi_ddc_clk ddc clock 7 dvi_ddc_dat ddc data 8 dvi_vs_in analog vertical sync 9 /rx1 tmds data 1- 10 rx1 tmds data 1+ 11 gnd digital ground 12 nc no connection 13 nc no connection 14 dvi_ddc_5v +5v power supply for ddc (optional) 15 gnd ground (+5, analog h/v sync) 16 nc no connection 17 /rx0 tmds data 0- 18 rx0 tmds data 0+ 19 gnd digital ground 20 nc no connection 21 nc no connection 22 gnd digital ground 23 rxc tmds clock+ 24 /rxc tmds clock- 25 nc no connection 26 nc no connection pp2 - 24vdc power supply input (matching type : molex 43025-0400 compatible) pin description 1 +24vdc 2 ground 3 +24vdc 4 ground
11 controller dimensions the maximum thickness of the controller is 19.6mm (meas ured from bottom of pcb to top of components, including any underside components & leads). we recommend clearances of: ? 5mm from bottom of pcb - if mounting on a metal plate we also recommend a layer of suitable insulation material is added to the mounting plate surface. ? 10mm above the components ? 3~5mm around the edges any of the holes shown above can be used for mount ing the pcb, they are 3.2mm in diameter. caution: ensure adequate insulation is provided fo r all areas of the pcb with special attention to high voltage parts such as the inverter.
12 application notes using the controller without buttons attached this is very straightforward by following the steps below : ? use a jumper to close jp6 jumper, this will fix the board on. ? refer to inverter specifications for det ails as to fixing brightness to a desired level, this may require a resistor, an open circuit or closed circ uit depending on inverter. inverter connection there are potentially 3 issues to c onsider with inverter connection: ? power ? enable ? brightness please read the following sections for a guide to these issues. inverter power : as per the table for cnb1 pin 3,4 are ground and pin 1, 2,5 provides 24vdc. this should be matched with the inverter specification: see table. cnb1 pin description 1 backlight power supply, +24vdc 2 backlight power supply, +24vdc 3 ground 4 ground 5 backlight power supply, +24vdc enable : this is a pin provided on some inverters for on/off function and is used by this panel controller for vesa dpms compliance. if the inverter does not have an enable pin or the enable pin is not used then dpms will not be operational. pin 6 should be matched to the inverters specificati on for the ?enable? or ?disable? pin. cnb1 pin description 6 enable further, jumpers jb2 & jb3 should be set to match the inverter s specification for the enable pi n power and high or low setting: see table. ref purpose note jb2 inverter enable voltage 1-2 h = 5v, 2-3 h = 3.3v, open h = open collector jb3 inverter control 1-2 h = on, 2-3 l = on brightness : there are various methods for brightness control and it is impor tant to consider the specific ations for the inverter to be used. generally the situation is: ? brightness can controlled by using a re sistor or vr (variable resistor). ? no adjustment of brightness is possible. cnb1 pins 4 & 5 are available for c onnecting to an inverter or circuit where vr control is supported. cnb1 pin description 7 vr wip 8 vr a this can then be matched with function controls (osd switch mount) pins 3 & 4: see cable design below .
13 troubleshooting general a general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements, such as : ? controller (jumpers, pc settings) ? panel (controller, cabling, connection, panel, pc settings) ? backlight (inverter, c abling, backlight tubes) ? cabling ? computer system (display settings, operating system) through step by step cross checking with instruction manuals and a pr ocess of elimination to isolate the problem it is usually possible to clearly identify the problem area. no image: ? if the panel backlight is not working it may still be possible to just see some image on the display. ? a lack of image is most likely to be caused by incorrect connec tion, lack of power, failure to provide a signal or incorrect graphic card settings. image appearance: ? a faulty panel can have blank lines, failed sections, fli ckering or flashing display ? incorrect graphics card refresh rate, resolution or interl aced mode will probably cause the image to be the wrong size, to scroll, flicker badly or possibly even no image. ? incorrect jumper settings on the controlle r may cause everything from total failure to incorrect image. caution: do not set the panel power input incorrectly. ? sparkling on the display: faulty panel signal cable. backlight: items to check include: power input, controls, inverter and tubes generally in this order. if half the screen is dimmer than the other half: ? check cabling for the inverter. ? for a specific backlight tube check the ac pins or ientation (caution: never reverse any dc power pins). also: ? if adjusting brightness control has no effe ct the chances are that the vr rating or method of adjusting brightness is not compatible or correctly connected to the inverter. ? if system does not power down when there is a loss of signal continued failure: if unit after unit keeps failing c onsider and investigate whether you are short circuiting the equipment or doing something els e seriously wrong. generally after common sense issues hav e been resolved we recommend step by step s ubstitution of known working parts to isolate the problem.
14 specifications panel compatibility 2560x1600 resolution tft tmds 18v lcd?s panel support. no. of colours up to 3 x 8 bit providing 16.7 million colours. vertical refresh rate wqxga (2560x1600) resolution up at 60hz. graphics formats 2560x1600 60hz signal standard input at source - dvi-d controls available - on/off - brightness (inverter) vesa dpms implementation yes plug & play vesa ddc 1, 2/b compatible voltage output for lcd +18v only input voltage 24vdc controller power consumption approx 1.5w (controller logic only, no panel and inverter are involved) controller dimensions 107mm x 92mm x 19.6mm storage temperature limits -40 o c to +70 o c operating temperature limits 0 o c to +60 o c notes please note the following: ? for specific panel setup a sample of an lcd may be requir ed (this will be returned) and a copy of the full technical specifications for the panel from the manufacturer. ? relayout and custom development services are available.
15 appendix i ? graphic mode support table mode resolution interface wqxga 2560x1600 60hz dvi-d
16 warranty the products are warranted against defects in workmanship and material for a period of three (3) year from the date of purchase provided no modificati ons are made to it and it is operated under nor mal conditions and in compliance with the instruction manual. the warranty does not apply to: ? product that has been installed incorrectly, this specifically in cludes but is not limited to case s where electrical short cir cuit is caused. ? product that has been altered or repaired except by t he manufacturer (or with the manufacturer?s consent). ? product that has subjected to misuse , accidents, abuse, negligence or unusual st ress whether physical or electrical. ? ordinary wear and tear. except for the above express warranties, the manufacturer disclaims all warranties on pr oducts furnished hereunder, including all implied warranties of merchantability and fitness for a parti cular application or purpose. the stated express warranties ar e in lieu of all obligations or liabilities on the part of the manuf acturer for damages, including but not limited to special, indir ect consequential damages arising out of or in connection with the use of or performance of the products. caution whilst care has been taken to provide as much detail as possible for use of this pr oduct it cannot be relied upon as an exhaustive source of information. this product is for use by suitably qualified persons who understand the nature of the work they are doing and are able to take suitabl e precautions and design and produc e a product that is safe and meets regulatory requirements. limitation of liability the manufacturer?s liability for damages to customer or others resulting from the use of any product supplied hereunder shall i n no event exceed the purchase price of said product. trademarks the following are trademarks of digital view ltd: ? digital view ? dvi-2560
17 contact details digital view has offices in asia, europe and usa also an internet site: asia digital view ltd 16 th floor millennium city 3 370 kwun tong road kwun tong hong kong tel : (852) 2861 3615 fax : (852) 2520 2987 sales : hksales@digitalview.com europe digital view ltd. 6 marylebone passage, london, w1w 8ex uk tel: +44-(0)20-7631-2150 fax: +44-(0)20-7631-2156 sales: uksales@digitalview.com usa digital view inc. 18440 technology drive building 130 morgan hill, california, 95037 usa tel : (1) 408-782 7773 fax : (1) 408-782 7883 sales : ussales@digitalview.com website www.digitalview.com specifications subject to change without notice 3nd issue: 3 feb, 2009 (dvi-2560.doc) ? digital view ltd 2007-2009
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: digital view: ? 426013700-3

▲Up To Search▲

Price & Availability of 41713002X-3

	To Download 41713002X-3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .