specifcations subject to change without notice. please check our website for latest information. chip inductors for critical applications ST336RAB 0805 chip inductors document st288-1 revised 06/01/11 ferrite core surface mount inductors lower dcr and higher current ratings than other 0805 series. available in inductance values from 0.078 to 27 h, all at 2% and 5% tolerance. inductance 2 percent srf min 4 dcr max 5 imax part number 1 (h) tolerance q min 3 (mhz) (ohms) (a) ST336RAB78n_lz 0.078 @ 7.9 mhz 5,2 19 @ 7.9 mhz 1440 0.042 2.0 ST336RAB111_lz 0.110 @ 7.9 mhz 5,2 19 @ 7.9 mhz 1200 0.05 2.0 ST336RAB471_lz 0.470 @ 7.9 mhz 5,2 19 @ 7.9 mhz 500 0.31 0.720 ST336RAB681_lz 0.680 @ 7.9 mhz 5,2 20 @ 7.9 mhz 400 0.46 0.590 ST336RAB102_lz 1.0 @ 7.9 mhz 5,2 20 @ 7.9 mhz 340 0.69 0.500 ST336RAB122_lz 1.2 @ 7.9 mhz 5,2 15 @ 7.9 mhz 280 1.20 0.400 ST336RAB152_lz 1.5 @ 7.9 mhz 5,2 20 @ 7.9 mhz 275 1.03 0.490 ST336RAB182_lz 1.8 @ 7.9 mhz 5,2 20 @ 7.9 mhz 246 1.15 0.410 ST336RAB222_lz 2.2 @ 7.9 mhz 5,2 20 @ 7.9 mhz 106 1.28 0.365 ST336RAB272_lz 2.7 @ 7.9 mhz 5,2 20 @ 7.9 mhz 105 1.48 0.350 ST336RAB332_lz 3.3 @ 7.9 mhz 5,2 20 @ 7.9 mhz 83 1.57 0.330 ST336RAB392_lz 3.9 @ 7.9 mhz 5,2 20 @ 7.9 mhz 52 1.70 0.300 ST336RAB472_lz 4.7 @ 7.9 mhz 5,2 20 @ 7.9 mhz 50 1.87 0.280 ST336RAB682_lz 6.8 @ 7.9 mhz 5,2 20 @ 7.9 mhz 35 2.25 0.260 ST336RAB822_lz 8.2 @ 2.5 mhz 5,2 18 @ 2.5 mhz 27 2.55 0.250 ST336RAB103_lz 10.0 @ 2.5 mhz 5,2 18 @ 2.5 mhz 21 3.45 0.200 ST336RAB153_lz 15.0 @ 2.5 mhz 5,2 18 @ 2.5 mhz 17 5.03 0.180 ST336RAB223_lz 22.0 @ 2.5 mhz 5,2 18 @ 2.5 mhz 13 6.18 0.150 ST336RAB273_lz 27.0 @ 2.5 mhz 5,2 15 @ 2.5 mhz 11 11.04 0.120 1. when ordering, specify tolerance, termination and testing codes: ST336RAB273glz tolerance: g = 2% j = 5% termination: l = rohs compliant silver-palladium-platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). testing: z = cots h = screening per coilcraft cp -sa-10001 2. inductance measured using a coilcraft smd-a fxture in an agilent/ hp 4286a impedance analyzer or equivalent with coilcraft-provided correlation pieces. 3. q measured on an agilent/hp 4291a with an agilent/hp 16197 test fxture or equivalents. 4. srf measured using an agilent/hp 8753es network analyzer or equivalent with a coilcraft smd-d test fxture. 5. dcr measured on a keithley 580 micro-ohmmeter or equivalent and a coilcraft ccf858 test fxture. 6. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering. core material ceramic/ferrite terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. ambient temperature C40c to +85c with i rms current, +85c to +100c with derated current storage temperature component: C55c to +100c. packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles temperature coeffcient of inductance (tcl) +100 to +255 ppm/c moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) packaging 2000 per 7 reel plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth 1102 silv er lak e road car y il 60013 phone fa x 800-981-0363 847-639-1508 e-mail we b cps@coilcraft.com www .coilcraft-cps .com ? ? coilcraft, inc. 2011
specifcations subject to change without notice. please check our website for latest information. 0805 chip inductors document st288-2 revised 06/01/11 a b c d max max max ref e f g h i j 0.090 0.075 0.063 0.020 0.050 0.020 0.040 0.070 0.040 0.030 inches 2,29 1,91 1,60 0,51 1,27 0,51 1,02 1,78 1,02 0,76 mm i i j h a b ov erall f g e ter minal f c d te r minal wraparound: appro x 0.010/0,25 both ends recommended land p attern pic k and place mater ial typical l vs frequency typical q vs frequency irms derating ST336RAB series (0805) suggested land pattern -40 -20 02 04 06 08 0 100 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 pe r cent of rated rms i 25c note: dimensions are before optional solder application. for maximum overall dimensions including solder, add 0.0025 in / 0,064 mm to b and 0.006 in / 0,15 mm to a and c. 1102 silv er lak e road car y il 60013 phone fa x 800-981-0363 847-639-1508 e-mail we b cps@coilcraft.com www .coilcraft-cps .com ? ? coilcraft, inc. 2011
|