TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 1 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com applications ? wlan ? cellular infrastructure ? test and measurement ? smart energy ? uhf/vhf ? lmr ? general purpose broadband wireless 8 - pin 2x2 mm dfn package ordering information part no. description TQP4M0013 sp s t absorptive switch TQP4M0013 - pcb 0.1 - 4.0 ghz evaluation board standard t/r size = 25 00 pieces on a 7 reel product features ? general purpose ? low insertion loss ? + 49 dbm input ip3 ? high isolat ion ? absorptive ? single positive voltage control ? small 2x2 mm smt package pin configuration pin no. label 1 , 4 nc 2 , 3 gnd 5 rf1 6 v dd 7 v ctrl 8 rf2 general description the TQP4M0013 is a gaas fet single - pole, single throw (sps t) high isolati on absorptive switch . the TQP4M0013 may be operated using a dc supply range from 3 to 5 volts and with control signals operating from 3 to 5 volts. the TQP4M0013 has 100 - 400 0 mhz broadband performance. the TQP4M0013 is packaged in a rohs - compliant, compact 2x2 mm surface - mount leadless package. this spdt switch is targeted for use in wireless infrastructure, test and measurement, or can be used for any general purpose rf application. functional block diagram g n d g n d n c n c v c t r l v d d r f 1 r f 2 b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k c o n t r o l l e r 8 7 6 5 1 2 3 4
TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 2 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com electrical specifications test conditions unless otherwise noted: v dd = +5 v, v ctrl = 0 v (low) or 3.3 v (high) , temp.=+ 25 c , 50 system parameter conditions min typ max units operational frequency range 100 4 0 00 mhz control voltage (v ctrl ) low 0 0. 2 v high 1.8 v dd v insertion loss 1 ghz 2 ghz 3 ghz 0. 55 0. 71 0. 77 0.87 db isolation 1 ghz 2 ghz 3 ghz 38 50 4 3 37 db rf 1/rf2 return loss insertion loss state 1 ghz 2 ghz 3 ghz 15 15 17 db rf2 return loss isolation loss state 1 ghz 2 ghz 3 ghz 16 15 17 db input p1db f= 1 ghz + 3 5 dbm input ip3 f= 1 ghz p in =+ 1 5 dbm/tone , f= 1 mhz + 4 9 dbm switching speed t on ,t off ( 50% ctl to 10/90% rf) 150 ns t on ,t off (50% ctl to 2/98% rf) 150 ns total supply current (i dd ) 82 ua absolute maximum ratings parameter rating storage temperature - 65 to 1 65 c rf input power , cw, 50, t = 25c +33 dbm supply voltage (v d d ) +6 v control voltage (v ctrl ) v dd +0.5 v operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ m ax units v dd 3.0 5 . 0 v operating temp. range - 40 +85 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. switch control truth table v ctrl signal path state ( rf1 to rf2) low off (isolation) high on (insert ion loss) control voltages state bias condition low 0. 2 v high 1.8 v
TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 3 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com TQP4M0013 - pcb evaluation board notes: 1. capacitance values shown for c1, c2, c3 and c4 are required to achieve data sheet rf performance specifications. performance p lots ? TQP4M0013 - pcb test conditions unless otherwise noted: v dd =+5 v, v ctrl = + 3 .3 v , temp= +25c, 50 system typical performan ce ? TQP4M0013 - pcb test conditions unless otherwise noted: v dd = +5 v , temp= 25 c , 50 system parameter typi cal value units frequency 1 2 3 g hz insertion loss (1) 0.55 0.71 0.77 db rf1/rf2 port return loss (insertion loss state) 15 15 17 db rf1 to rf2 isolation 50 43 37 db input p1db +3 5 dbm input ip3 ( p in=+ 1 5 dbm/tone , f=1 mhz ) + 49 +5 0 dbm notes: 1. in sertion l oss values reflect de - embedding of eval board rf line losse s. u 1 c 1 c 2 c 5 c 6 c 3 c 4 j 1 r f 2 b a c k s i d e p a d d l e j 2 r f 1 j 6 g n d u 1 1 2 3 4 8 7 6 5 c o n t r o l l e r c 4 5 p f v d d v c t r l j 4 j 5 c 3 5 p f c 2 3 5 p f c 1 3 5 p f - 2.5 - 2 - 1.5 - 1 - 0.5 0 0 500 1000 1500 2000 2500 3000 |s21| (db) frequency (mhz) insertion loss vs. frequency temp.=+25 c on state - 70 - 60 - 50 - 40 - 30 - 20 - 10 0 0 500 1000 1500 2000 2500 3000 isolation (db) frequency (mhz) rf1 to rf2 isolation vs. frequency temp.=+25 c off state - 25 - 20 - 15 - 10 - 5 0 0 500 1000 1500 2000 2500 3000 |s22| (db) frequency (mhz) rf2 return loss vs. frequency temp.=+25 on (insertion loss) state off (isolation) state
TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 4 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com pin configuration and description pin no. symbol description 1, 4 n/c no electrical connection. provide grounded land pads for pcb mounting integrity. 2, 3 gnd rf/dc ground 5 rf 1 rf port 1 . dc block required. 6 v dd bias voltage 7 v ctl control voltage 8 rf 2 rf port 2 . dc block required. internal resistive termination in off (isolation) state. backside paddle rf/dc gnd rf/dc ground. use recommended via pattern and ensure good solder attach for best thermal and electrical performance. evaluation board pcb specifications pcb 1094173 material and stack - up 50 ohm input/output (i/o) line structure w idth = 0 .02 8 gap = 0 .0 28 g n d g n d n c n c v c t r l v d d r f 1 r f 2 b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k c o n t r o l l e r 8 7 6 5 1 2 3 4 1 o z . c u b o t t o m l a y e r n e l c o n - 4 0 0 0 - 1 3 c o r e n e l c o n - 4 0 0 0 - 1 3 r = 3 . 7 t y p . 1 o z . c u t o p l a y e r 1 o z . c u i n n e r l a y e r 1 o z . c u i n n e r l a y e r 0 . 0 1 4 " 0 . 0 1 4 " 0 . 0 6 2 " 0 . 0 0 6 " f i n i s h e d b o a r d t h i c k n e s s
TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 5 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com mechanical information package marking and dimensions marking: product code C 013 assembly code - xxx n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. dimension and tolerance formats conform to asme y14.4m - 1994. 3. the terminal #1 identifier and terminal numbering c onform to jesd 95 - 1 spp - 012 pcb mounting pattern n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 4. ensure good package backside paddle solder attach for reliable operation a nd best electrical performance. 013 xxx 3x 3 0.64 0.35 package outline ?.254 (.010) plated thru via holes 1.60 8x 0.67 0.50 pitch, typ 8x 0.30 2x 0.20 0.70 top view side view bottom view terminal 1 identifier 0.200x45 2.000.05 2.000.05 0.800.05 exp. dap 0.300.050 1.600.05 exp. dap 0.50 bsc 0.250.05 0.203 ref 0.00-0.05 terminal 1 identifier 0.850.05
TQP4M0013 high isolation absorptive sp s t switch datasheet: rev c 0 9 - 06 - 13 - 6 of 6 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.com product compliance information esd sensitivity ratings caution! esd - s ensitive device esd rating: class 0 value: passes >125 v and < 250 v test: human body model (hbm) standard: jedec standard jesd22 - a114 esd rating: class iv value: passes >1000 v olts test: charged device model (cdm) standard: jedec standard jesd22 - c101 solderability comp atible with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) soldering processes. package contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directiv e (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free m sl rating msl rating : level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 important notice for the latest specifications, additional product information, worldwide sales and distribution locations, and information abou t triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@triquint.com contact information the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change witho ut notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent r ights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving , or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
|
