features applications photo ic transmitter/receiver photo ic for optical link 3.3 v operation, for most automotive network L10663-01, s10664-01 L10663-01 and s10664-01 are transmitter and receiver photo ics developed for most (media oriented system transport) networks us ed in vehicles to communicate multimedia information. lower operating voltages in recently manufactured electronic devices have spurr ed demand for low-voltage and low-current transmitter/receiver photo ics. to meet this need, hamamatsu has been developing low voltage (3.135 v to 3.465 v) photo ics that still maintain a wide operating temperature range (-40 ?c to +105 ?c) the same as the conventional types (l10063 -01/s10064-01). the transmitter photo ic l10663 consists of a red-led and driver ic incorporated into a clear plastic package and can be set to an operating mode that reduces the optical output level by half. the receiver photo ic s10664 features a wide dynamic range. it also has a low po wer consumption "sleeping mode" and an optical wakeup mode triggered by input of light. both the transmitter and receiver photo ic input or out put digital signals through a ttl interface. l wide operating temperature range: -40 to +105 ?c l dc to 50 mbps data communications l ttl input l optical output 50 % cut mode l only for vehicle networks (most) L10663-01 s10664-01 l low current: 2.4 ma max. (operating mode) 15 ? max. (sleeping mode) l wide operating temperature range: -40 to +105 ?c l 4 m to 50 mbps data communications l ttl output l sleeping mode with optical wakeup 1 electrical and optical characteristics (ta= -40 to +105 c, vcc= 3.135 to 3.465 v * 1 ) parameter symbol condition min. typ. max. unit current consumption icc vin= 2.0 v, rcont=13.5 k ? - - 40 ma peak emission wavelength p 630 650 670 nm spectral half width (fwhm) ? - 20 30 nm fiber coupled optical output 1 po1 rcont=13.5 k ? * 2, * 3 -9.5 - -2 dbm fiber coupled optical output 2 po2 rcont=27 k ? * 2, * 3 -13 - -4.5 dbm extinction ratio re 10 - - db rise time at pulse drive tr 20 to 80 % * 2 - - 5.5 ns fall time at pulse drive tf 80 to 20 % * 2 - - 5.5 ns pulse width variation tpwv 50 % * 2, * 4 19.99 - 24.29 ns pulse width distortion (average value) tapwd 50 % * 2, * 4 -1.39 - +1.39 ns * 1: a bypass capacitor (0.1 f) connected between vcc and gnd at a position within 3 mm from the lead, and a 10 f capacitor is also connected to the power supply line nearby. the center of the optical fiber is aligned with the center of the package lens. the distance between the fiber end and the lens top is 0.1 mm. an external resistor (rcont) is connected between cont and -vcc. * 2: measured with input signals conforming to sp1 most specification of physical layer rev 1.1 addendum b. *3: average value measured with a plastic fiber ( 1 mm, si-pof, na=0.5, 1 m) made by mitsubishi rayon. *4: measured with biphase prbs at 45.2 mbps (nrz signal conversion). L10663-01 absolute maximum ratings * 1 (ta= -40 to +105 c) parameter symbol l10663, s10664 unit supply voltage vcc -0.5 to +7.0 v operating temperature topr -40 to +105 c storage temperature tstg -40 to +120 c soldering ts o l 260 c, 5 s, 3 times, at least 2.5 mm away from lead root - most compliant products specifications of these products are subject to change without prior notice to keep up with changes in the most standard.
transmitter/receiver photo ic for optical link L10663-01, s10664-01 2 mode output waveform (s10664-01) kpicc0095ea output waveform example (s10664-01) tso tos voh vmh vol input signal data optical input no input signal mode output output voltage output data vml 1.5 v gnd tpwv (min.) tpwv (max.) trigger point vertical axis: 1 v/div., horizontal axis: 5 ns/div. (ta=25 c, vcc=3.465 v, pi= -26 dbm, r l =50 k ? , c l =15 pf, 45.2 mbps) electrical and optical characteristics (ta= -40 to +105 c, vcc=3.135 to 3.465 v * 5 ) parameter symbol condition min. typ. max. unit current consumption (operation mode) icco * 6 - - 24 ma current consumption (sleeping mode) iccs dark state - - 15 a receiver level popt3 bi-phase signal -25 - -2 dbm high level output voltage voh ioh= -150 m 2.5 - vcc+0.3 v low level output voltage vol iol=1.0 ma 0 - 0.4 v rise time tr - - 9 vout fall time tf 10 to 90 % * 6, * 7 - - 7 ns pulse width variation tpwv * 6, * 7, * 8, * 9 17.09 - 29.79 ns pulse width distortion (average value) tapwd * 6, * 7, * 8, * 9 -2.69 - +6.49 ns operation to sleeping mode transition receivable level psl sleeping mode to operation transition receivable level pop * 6, * 10 -39 - -25.5 dbm high level voltage vmh imh= -20 a 2.5 - - v mode output low level voltage vml iml=0.3 ma - - 0.5 v *5: a bypass capacitor (0.1 f) is connected between vcc and gnd at a position within 3 mm from the lead, and a 10 f capacitor is also connected to the power supply line nearby. the center of the optical fiber is aligned with the center of the package lens. the distance between the fiber end and the lens top is 0.1 mm. *6: measured with input signals conforming to sp3 most specification of physical layer rev 1.1 addendum b. *7: measured with r l =50 k ? , c l =15 pf (including parasitic capacitance such as probe, connector and evaluation circuit board pattern), and threshold voltage 1.5 v. *8: an optical input waveform is generated with a hamamatsu standard transmitter. *9: measured with biphase prbs at 45.2 mbps (nrz signal conversion). *10: average optical output is measured with a pof (na=0.5). note) if modulated light at 4 mbps or less (including dc light and no light input) is input to s10664-01, the high and low leve ls cannot be discerned. s10664-01
transmitter/receiver photo ic for optical link L10663-01, s10664-01 hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184, www.hamamats u.com u.s.a.: hamamatsu corporation: 360 foothill road, p.o.box 6910, bridgewater, n.j. 08807-0910, u.s.a., telephone: (1) 908-231-0 960, fax: (1) 908-231-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 8152- 375-0, fax: (49) 8152-265-8 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, teleph one: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, unit ed kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: smidesv ? gen 12, se-171 41 solna, sweden, telephone: (46) 8-509-031-00, fax: (46) 8-509-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1/e, 20020 arese, (milano), italy, telephone: (39) 02-935-81-733, fax: (39) 02-935-81-741 information furnished by hamamatsu is believed to be reliable. however, no responsibility is assumed for possible inaccuracies or omissions. specifications are subject to change without notice. no patent rights are granted to any of the circuits described herein. type numbers of products listed inthe specification sheets or supplied as samples may have a suffix "(x)" which means tentative specifications or a suffix "(z)" which means developmental specifications. ?2010 hamamatsu photonics k.k. cat. no. kpic1071e02 mar. 2010 dn 2.03 2.94 5.92 (3 ) d = 0.8 0.05 7.2 0.2 (including burr) 8.98 0.2 (including burr) 5.9 0.2 (including burr) (18.0) 5.1 2.54 (4 ) 0.5 0.05 2.54 (specified at the lead root) (specified at the lead root) 2.54 2.45 3.7 0.05 1.07 a? a 1.27 (4 ) 0.25 0.05 1.50 (2 ) 10 ? (2 ) 10 ? 2.85 2.72 1.57 0.97 2.0 depth 0.15 max. 0.6 2.92 1.8 1.24 0.2 0.66 (2 ) 5 ? 0.05 + 0.05 a-a? cross section 0.23 - 0.03 pin no. s10664-01 vcc gnd modeout vout L10663-01 v in gnd vcc cont 2.03 2.94 5.92 (3 ) d = 0.8 0.05 7.2 0.2 (including burr) 8.98 0.2 (including burr) 5.9 0.2 (including burr) (18.0) 5.1 2.54 (4 ) 0.5 0.05 2.54 2.54 2.45 3.7 0.05 1.07 a? a? 1.27 emitting point active area tolerance unless otherwise noted: 0.1, 2 ? r0.3 max. values in parentheses indicate reference value. shaded area indicates burr. lead material: cu alloy with ni/pd/au plating 0.6 0.6 dimensional outlines (unit: mm) L10663-01 s10664-01 kpica0077ea
|
