View CAT6500_8258698.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2015 november, 2015 ? rev. 2 1 publication order number: CAT6500/d CAT6500 3.0 a power selector switch description CAT6500 is an automatic power switch designed to select between two power sources and direct that power to a load for battery charging or system power. CAT6500?s power inputs withstand voltages of up to 18 v and protect the downstream load from voltages exceeding 7 v. in the event of a polarity reversal at either input CAT6500?s internal power switches will shut off to prevent discharge of the system?s internal power source. low resistance power switches handle currents in excess of 3 a and when off block current flow in both directions. CAT6500 can operate in reverse mode in which internal system power is be directed to either of the power input ports for powering an external device, such as a usb on?the?go appliance. features ? autonomous switching between 2 power sources ? withstands +18 v to ?5 v on either power input ? 80 m switches (typ.) for low power loss ? reverse?mode for powering external devices ? over voltage protection of downstream load ? compatible with usb?otg devices ? 32?lead wqfn 4.4 mm x 4.4 mm package ? this device is pb?free, halogen free/bfr free and is rohs compliant typical applications ? mobile phones ? pdas ? personal navigation devices figure 1. typical application circuit c1 li?ion + ? power management ic or battery charge priority rm_en2 rm_en1 sw2_stat sw1_stat pwr_out vcc ps2 ps1 CAT6500 0.1 f www. onsemi.com wqfn?32 hva suffix case 485bn marking diagram device package shipping ? ordering information CAT6500hv a?t2 wqfn?32 (pb?free) 2,000/ tape & reel 1 6500 = specific device code ssss = last four digits of assembly lot number a = assembly location l = wafer lot number (optional) y = production year w = production week = pb?free package 6500 ssss alyw ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specification brochure, brd8011/d.
CAT6500 www. onsemi.com 2 figure 2. simplified block diagram gnd ovp detect ps2 detect sw2 ps2 150 mv + ?+ ?+ ? 7 v 1.7 v level shifter control logic level shifter c1 vcc ps1 thermal shutdown charge pump v ref 1.7 v 7 v ovp detect ps1 detect sw1 150 mv pwr_out voltage source selection + ?+ ?+ ? sw2_stat sw1_stat pwr_out priority rm_en2 rm_en1 pin connections figure 3. pin connections w/rear pads shown (top view) sw1_stat sw2_stat gnd or floating ps1 rm_en1 gnd rm_en2 priority nic pwr_out pwr_out pwr_out pwr_out nic ps2 ps2 ps2 35 36 33 34 pwr_out ps2 ps1 ps2 ps2 nic nic vcc gnd c1 nic 32 1 pwr_out pwr_out pwr_out nic ps1 ps1 ps1 ps1
CAT6500 www. onsemi.com 3 table 1. pin function description pin no. pin name description 1, 2, 3, 4 pwr_out power output. must be tied to pwr_out on opposite side of chip. use all 3 pins each side. 5 nic no internal connection. a signal or voltage applied to this pin will have no effect on device operation. 6, 7, 8, 9, 10 ps2 power source #2. external power input 11, 12 nic no internal connection. a signal or voltage applied to this pin will have no effect on device operation. 13 vcc power input from battery. 14 gnd ground. reference point for all voltages. 15 c1 filter capacitor for CAT6500?s internal power bus 16 nic no internal connection. a signal or voltage applied to this pin will have no effect on device operation. 17 nic no internal connection. a signal or voltage applied to this pin will have no effect on device operation. 18 priority priority selects preferred power source when both ps1 and ps2 are powered. 19 rm_en2 reverse mode enable 2. overrides priority and turns sw2 on. 20 gnd ground. reference point for all voltages. 21 rm_en1 reverse mode enable 1. overrides priority and turns sw1 on. 22 ps1 power source #1. external power input. 23 sw2_stat power source 2 status. an open drain low true logic level output indicating that the switch sw2 is turned on. 24 sw1_stat power source 1 status. an open drain low true logic level output indicating that the switch sw1 is turned on. 25, 26, 27, 28 ps1 power source #1. external power input. 29 nic no internal connection. a signal or voltage applied to this pin will have no effect on device operation. 30, 31, 32 pwr_out power output. must be tied to pwr_out on opposite side of chip. use all 3 pins each side. 33 pwr_out electrically active thermal pad. does not need to be connected to other pwr_outs. can be left float- ing but must not be connected to other signal paths or ground. 34 ps2 electrically active thermal pad. does not need to be connected to other ps2 pins. can be left floating but must not be connected to other signal paths or ground. 35 ? mechanical support for control ic. this chip does not generate any significant heat and does not need a separate heat sinking connection. electrically this may be left floating or can be grounded. it should not be connected to other signals or voltages. 36 ps1 electrically active thermal pad. does not need to be connected to other ps1 pins. can be left floating but must not be connected to other signal paths or ground.
CAT6500 www. onsemi.com 4 table 2. absolute maximum ratings parameter symbol pin range unit input voltage range (note 1) v ps ps1, ps2 ?5.0 to 18 v v cc , v pwr_out vcc, c1, pwr_out ?0.3 to 6.0 control logic input range v l_in rm_enx, priority ?0.3 to 6.0 v control logic output range v l_out sw1_stat , sw2_stat ?0.3 to 6.0 v maximum junction temperature t j(max) ? 150 c storage temperature range t stg ? ?65 to 150 c esd capability, human body model (note 2) esd hbm all 2 kv esd capability, machine model (note 2) esd mm all 200 v lead temperature soldering reflow (smd styles only), pb?free versions (note 3) t sld all 260 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. refer to electrical characteristics and application information for safe operating area. 2. this device series incorporates esd protection and is tested by the following methods: esd human body model tested per aec?q100?002 (eia/jesd22?a114) esd machine model tested per aec?q100?003 (eia/jesd22?a115) latchup current maximum rating: 150 ma per jedec standard: jesd78 3. for information, please refer to our soldering and mounting techniques reference manual, solderrm/d table 3. thermal characteristics (note 4) parameter symbol value unit thermal characteristics, tdfn?32 4.4 x 4.4 mm thermal resistance, junction?to?air, 1 sq. inch, 1 oz. copper clad pcb thermal resistance, junction?to?air, 1 sq. inch, 2 oz. copper clad pcb r ja 59 54 c/w 4. values based on copper area of 645 mm 2 (or 1 in 2 ) of 1 oz copper thickness and fr4 pcb substrate. table 4. recommended operating conditions parameter symbol min max unit input voltage ps1, ps2 v cc 1.6 5.5 v v pwr_out 0 5.5 v ps1 , v ps2 ?5 7.7 output current i pwr_out 0 3.3 a control logic; inputs and outputs v l_in , v l_out 0 5.5 v ambient temperature t a ?40 +85 c functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability.
CAT6500 www. onsemi.com 5 table 5. electrical operating characteristics (v cc = 3.9 v, c1 = 0.1 f, unless otherwise noted. typical values t a = 25 c, min/max values t a = ?40 c to +85 c.) parameter test conditions symbol min typ max unit input / output input voltage ps1 or ps2 normal operation mode v ps 1.6 3.9 7.7 v ps1 or ps2 overvoltage protection mode v ps 1.6 3.9 12 vcc v cc 2.5 3.9 5.5 operating current; sw1 and sw2 on measured at vcc rm_en1 = 1, rm_en2 = 1 1.7 v < ps1 < 2.4 v, 1.7 v < ps2 < 2.4 v i vcc ? 85 120 a quiescent current; sw1 and sw2 off measured at vcc priority = 1, rm_en1 = 0, rm_en2 = 0 ps1 < 1.5 v, ps2 < 1.5 v i vcc ? 35 45 a input voltage detect ps1, ps2, voltage rising v detr 1.6 1.7 1.8 v ps1, ps2, voltage falling v detf 0.1 0.15 0.3 over voltage detection ps1, ps2, voltage rising v ovp 6.5 7.0 7.8 v over voltage hysteresis ps1, ps2, voltage falling v hys 100 ? 250 mv reverse voltage detect threshold ps1, ps2 v rev ?0.7 ? ?1.0 v power switches switch resistance; sw1, sw2 measured from psx to pwr_out ps1 or ps2 = 2.5 v, 5 c r on ? 80 110 m ps1 or ps2 = 5 v, 25 c ? ? ? ps1 or ps2 = 5 v, ?40 c to +85 c ? ? 135 logic input threshold voltage voltage increasing, logic high priority, rm_en1, rm_en2 v th_high 1.0 ? 1.5 v voltage decreasing, logic low priority, rm_en1, rm_en2 v th_low 0.4 ? 0.8 input current priority, pull?up i in ? 10 20 a rm_enx, pull?down ? 10 20 output current high v oh = v in ? 0.3 v sw1_stat, sw2_stat i oh ? 10 15 a output voltage low i ol = 3.0 ma sw1_stat, sw2_stat v ol ? 0.3 0.4 v timing sw turn?on delay time measured from rising edge of rm_enx to 10% of voltage at psx; psx = 2.0 v t on_dly ? 100 ? s sw rise time measured at pwr_out 10% to 90% of voltage applied at psx ps = 2.0 v t rise ? 200 300 s measured at pwr_out 10% to 90% of voltage applied at psx ps = 5 v ? 100 250 sw turn?off time measured at pwr_out 90% to 10% of voltage applied at psx t off ? ? 25 s over voltage t urn?off time ps = 0 v 10 v t off_ov1 ? 10 ? s ps = 5 v 10 v t off_ov2 ? 10 ? break?before?make off time measured at pwr_out, off time during transition from ps1 ps2 or ps2 ps1 t off_bbm ? 400 ? s thermal shutdown thermal shutdown temperature t sd ? 145 ? c thermal shutdown hysteresis t sh ? 10 ? c
CAT6500 www. onsemi.com 6 psx off on rm_enx 0 1 figure 4. switch timing psx pwr_out 5 v 0 v 10 v 5 v 0 v 7 v 7 v 5 v 0 v 10 v 5 v 0 v psx pwr_out case 2 case 1 figure 5. overvoltage turn?off timing ps1 off on rm_en1 0 1 0 1 rm_en2 ps2 off on figure 6. break?before?make switching t off t on_delay t rise t off_ov1 t off_ov2 t off_bbm t off_bbm
CAT6500 www. onsemi.com 7 typical performance characteristics figure 7. operating supply current vs. vcc figure 8. quiescent supply current vs. vcc supply voltage (v) supply voltage (v) 6 5 4 3 2 32 42 52 62 72 82 92 102 6 5 4 3 2 27 29 31 33 35 37 39 41 figure 9. ps_ detect threshold vs. vcc figure 10. ps_ release threshold vs. vcc supply voltage (v) supply voltage (v) 6 5 4 3 2 1.696 1.698 1.700 1.702 1.704 1.706 1.708 1.710 6 5 4 3 2 0.118 0.120 0.130 figure 11. vth_high vs. vcc figure 12. vth_low vs. vcc supply voltage (v) supply voltage (v) 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 0.8 0.9 1.0 1.1 1.2 1.4 1.5 1.6 6 5 4 3 2 0.45 0.50 0.55 0.65 0.70 0.75 0.85 0.90 i supply ( a) i supply ( a) threshold voltage (v) threshold voltage (v) threshold voltage (v) threshold voltage (v) ?40 c 25 c 90 c ?40 c 25 c 90 c ?40 c 25 c 90 c 0.122 0.124 0.126 0.128 0.132 0.134 0.136 0.138 ?40 c 25 c 90 c 6.0 1.3 ?40 c 25 c 90 c ?40 c 25 c 90 c 0.60 0.80
CAT6500 www. onsemi.com 8 typical performance characteristics figure 13. over?voltage threshold vs. vcc figure 14. switch r on vs. vcc supply voltage (v) supply voltage (v) 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 6.96 6.98 7.00 7.02 7.04 7.06 7.10 7.12 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 50 55 65 70 75 80 90 95 figure 15. t on_dly vs. vcc figure 16. t off vs. vcc supply voltage (v) supply voltage (v) 6 5 4 3 2 0.08 50.08 100.08 150.08 200.08 250.08 300.08 350.08 6 5 4 3 2 12.50 12.55 12.60 12.65 12.70 12.75 12.80 figure 17. t rise vs. vcc supply voltage (v) 6 5 4 3 2 0.08 20.08 40.08 60.08 80.08 100.08 120.08 140.08 over?voltage threshold (v) switch resistance (m ) sw turn?on delay time ( s) sw turn?off time ( s) t rise ( s) ?40 c 25 c 90 c 6.0 7.08 ?40 c 25 c 90 c 60 85 6.0 ?40 c 25 c 90 c ?40 c 25 c 90 c ?40 c 25 c 90 c
CAT6500 www. onsemi.com 9 pin functions sw1, sw2 sw1 and sw2 are low on resistance power fet switches within CAT6500 and form the power transfer path between ps1, ps2 and pwr_out. sw1 and sw2 are bidirectional allowing for current to flow in either direction. they are controlled by the digital inputs priority, rm_en1, rm_en2. while they are not device pins they are defined here in order to make pin functions more understandable. ps1, ps2 these are input pins for two external power sources which supply power for battery charging and system operation. on the basis of a priority input, CAT6500 will select from ps1 or ps2 and route power to pwr_out. if power on the preferred input is unavailable or the voltage is insufficient and a suitable power source is available on the other power input then CAT6500 will use the alternate source. ps1 and ps2 can also supply power to external devices if a reverse?mode command is given. in reverse?mode, pwr_out becomes the power source and is connected to either ps1 or ps2 in accord with the reverse?mode command. it is possible for both ps1 and ps2 to be powered simultaneously by pwr_out if commanded by the reverse?mode inputs. this dual command state also allows for power transfer between ps1 and ps2. pwr_out pwr_out is the common point between sw1 and sw2 and conducts power from either of these inputs to the system?s power bus. when used in reverse mode pwr_out can supply power to an external load such as a usb device attached to ps1 or ps2. rm_en1, rm_en2 reverse mode enable inputs are logic high signals which will override autonomous voltage source selection and force either sw1 or sw2 into an on state. rm_en1 and rm_en2 act independently of each other and therefore can both be active at the same time. vcc vcc is an alternative power source for CAT6500 in the event neither ps1 nor ps2 is powered or if CAT6500 is in reverse?mode and is supplying power to an external device. vcc supplies only CAT6500?s internal control logic circuitry and is never routed to ps1, ps2 or pwr_out. c1 CAT6500 can draw its operating current from several different inputs and will switch between these sources as they change or become available. to keep the chip? s internal supply voltage stable during these transitions an external filter capacitor is required. the recommended value for c1 is between 0.1 f and 1.0 f. gnd the negative power input pin for CAT6500 and system ground. priority priority is a logic signal input that directs power source selection in forward mode if both ps1 & ps2 sources of power are present at the same time. for priority low, ps1 is selected. if only one source of power is present, CAT6500 will default to that source. priority can be overridden by a rm_enx command in which case the associated power fet sw1 or sw2 is turned on by the rm_en command. sw1_stat , sw2_stat sw1_stat and sw2_stat are open drain low true digital outputs indicating the operating state of power switch 1 (sw1) and power switch 2 (sw2), where a low indicates the switch is on. sw1_stat and sw2_stat may be pulled up to an external voltage greater than vcc or greater than psx as long as it does not exceed 5.5 v. sw1_stat and sw2_stat are active in reverse?mode and continue to indicate the operational status of sw1 and sw2.
CAT6500 www. onsemi.com 10 circuit description and operating considerations description CAT6500 is an autonomous power selector switch designed for portable device applications where either of two power sources may be used for battery charging and device operation. CAT6500 can operate in two distinct modes, forward or reverse, depending on the states of the rm_enx inputs. in forward mode, ca t6500 will automatically select from the available power sources, ps1 or ps2, and direct one to pwr_out. in reverse mode, a system power rail connected to pwr_out can source power to an external device attached to either ps1 or ps2. this allows charging or powering of other portable devices. power source selection in forward mode, on?chip voltage detection circuitry senses the presence of a suitable power source at power inputs, ps1 and ps2. if both inputs are powered the priority pin sets the preferred power source directs that source to pwr_out. if only one of the two inputs is powered then that power source is directed to pwr_out. CAT6500 provides two status outputs swx_stat to indicate the presence of a voltage at either ps1 or ps2. these status outputs trigger at 1.7 v and are low true digital outputs. priority has an internal pull?up and defaults to a logic high if the pin is disconnected or left floating. input selection follows the truth table in table 6. CAT6500 draws its operating power from ps1 or ps2 when a voltage of 2.5 v or more is present. if no power is present at ps1or ps2 or ca t6500 is in reverse mode, power will be drawn from vcc. CAT6500 provides overvoltage protection to circuitry downstream from the chip by limiting input voltages to 7 v. should the voltage at ps1 or ps2 rise above 7 v then pwr_out will be disconnected from the power source until the voltage returns to safe levels. CAT6500 provides similar protection for reverse polarity voltages down to ?5 v. reverse mode operation the rm_enx inputs allow CAT6500 to operate the power switches in reverse mode where the pwr_out becomes the supply powering ps1 and/or ps2. when rm_en1 is logic high, sw1 switch is turned on and pwr_out is connected to ps1. when rm_en2 is logic high, sw2 switch is turned on and pwr_out is connected to ps2. the switch connection remains on until the pwr_out voltage decreases all the way to 0 v (below 0.1 v typical) regardless of the state of the associated rm_enx input. rm_en is not affected by the voltage levels seen at ps1 or ps2 as priority and will not switch off automatically if the voltage drops below 1.7 v as would CAT6500 otherwise do. this allows the power connection to be used for signaling purposes as in usb on?the?go where power line signaling is used to request a transfer of bus master status between devices. when operating in reverse mode, the sw1_stat and sw2_stat outputs are still active and will reflect the switch conditions. rm_en1 and rm_en2 are independent controls and can be activated simultaneously, meaning both sw1 and sw2 can be conducting at the same time. this presents both opportunities and hazards. having both switches on allows for simultaneous charging or powering of two devices from a single source; a usb power source can charge and operate the device as well as power an additional unit connected to the other ps input. or the device can power two external units attached to ps1 and ps2. the downside of this capability becomes apparent when two operating power sources are present at the same time. if both switches are on the power sources will compete with the stronger driving the weaker. for example; if a wall charger is attached to ps1 and an active usb port to ps2, with both sw1 and sw2 on, the wall charger will likely dominate and push power backwards into the usb port, possibly elevating the usb bus voltage above allowable limits. note: sw1 and sw2 are not current limited and can conduct very high currents if short circuited. current limiting circuitry is advisable if short circuits are possible in the intended application. entering and exiting reverse mode when entering or exiting reverse mode, it is recommended that power applied to pwr_out be sequenced with the enabling/disabling signal. it is best to enter reverse mode with pwr_out at 0 v and apply power after the logic control. similarly on exiting reverse mode, power should be taken to 0 v and then the switch disabled. pwr_out rm_en 0 1 0 v figure 18. entering and exiting reverse mode v out
CAT6500 www. onsemi.com 11 over?voltage CAT6500 is designed to withstand input voltages of up to 18 v on the ps1 or ps2 inputs. in the event of such a fault condition, sw1 or sw2, whichever is exposed to the fault will shut off. this fault protection is voltage sensitive, activating at 7 v typically and overrides control inputs priority, rm_en1 and rm_en2. the response time of the over voltage detection circuit is constant and independent of the rise time of the overvoltage event, however the voltage transient seen at pwr_out will vary depending upon the operating conditions at the time of the event. case 1 and case 2 of figure 5 illustrates this. in case 1, an overvoltage is applied to a ps input as would happen if a malfunctioning or improper charger were used to recharge a handheld appliance. the internal fet switch is initially off and the application of voltage at the ps input initiates turning it on, but the delay associated with turning on the switch is very long compared to the overvoltage comparator?s response time. the resulting voltage transient at pwr_out is very small to non?existent because the fet switch never gets the chance to turn fully on. case 2 assumes voltage is applied to a ps input and the internal fet switch is on. if for some reason the applied voltage surges above the overvoltage threshold the fet will be turned off but a transient will be seen at pwr_out. the degree to which the voltage at pwr_out exceeds the overvoltage threshold depends upon the rate of voltage rise at ps compared to the comparator?s response time. CAT6500 is tolerant to negative voltages as well and shuts off sw1 and sw2 when either ps1 or ps2 goes negative by more than 0.7 v. table 6. power switch control and selection inputs connections outputs ps1 ps2 rm_en1 rm_en2 priority sw1 sw2 pwr_out sw1_stat sw2_stat l l 0 0 x 0 0 0 1 1 h l 0 0 0 1 0 ps1 0 1 l h 0 0 0 1 ps2 1 0 h h 0 0 1 0 ps1 0 1 h l 0 0 1 1 0 ps1 0 1 l h 0 0 0 1 ps2 1 0 h h 0 0 0 1 ps2 1 0 pwr_out hi?z 1 0 x 1 0 x 0 1 hi?z pwr_out 0 1 0 1 x 1 0 pwr_out pwr_out 1 1 1 1 x 0 0 l 1.7 v h 1.7 v default = 0 default = 1 0 = open 1 = closed for voltage rising at ps if left floating if left floating break?before?make switching when switching between power sources either under automatic control (priority) or in override (rm_en), CAT6500 disables the active switch before the new connection is made. this ensures there will be no unintended cross conduction between ps1 and ps2. even when sw1 and sw2 are commanded to be on simultaneously there is a brief interval when both sw1 and sw2 are off. figure 6 illustrates this. thermal considerations under normal operating conditions sw1 and sw2 will dissipate some amount of heat which is a function of the current through the switch and ron. t ypical heating curves are shown in figure 19. CAT6500 is protected against overheating by an internal temperature sensor. should the chip?s temperature reach 145 c CAT6500 will shut off both power switches until the die temperature drops to below approximately 135 c, at which time the power switches will be returned to their original operating state. if the temperature again exceeds the thermal shutdown limit both switches will be disabled and this cycling will continue until current flowing through the switch is reduced, the load is removed or the switch is turned off under system control.
CAT6500 www. onsemi.com 12 figure 19. power dissipation vs. switch current and resistance switch current (a) 4 3 2 1 0 0 0.5 1.0 1.5 2.0 2.5 power dissipation (w) 135 m 110 m 85 m figure 20. ja vs. copper heat spreader area 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 52 54 56 58 60 62 64 66 0 100 200 300 400 500 600 700 power (w) ja ( c/w) copper heat spreader area (mm 2 ) power curve with pcb cu thk 1.0 oz power curve with pcb cu thk 2.0 oz ja curve with pcb cu thk (no vias) 1.0 oz ja curve with pcb cu thk (no vias) 2.0 oz
CAT6500 www. onsemi.com 13 package dimensions wqfn32 4.4x4.4, 0.4p case 485bn issue a notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.25 mm from the terminal tip. 4. coplanarity applies to the exposed pad as well as the terminals. 5. positional tolerance applies to all of the exposed pads. ??? ??? ??? a d e b c 0.15 pin one reference top view side view bottom view a d2 e2 c c 0.15 c 0.10 c 0.08 a1 seating plane e 32x note 3 b 32x c c a b dim min max millimeters a 0.70 0.80 a1 0.00 0.05 b 0.15 0.25 d 4.40 bsc d2 1.30 1.50 e 4.40 bsc e2 1.70 1.90 e 0.40 bsc l 0.30 0.50 9 17 25 1 l a3 0.20 ref note 4 a3 detail b detail a l1 detail a l alternate terminal constructions l l1 0.05 0.15 c a b m 0.10 m 0.05 f 1.55 bsc ??? detail b mold cmpd exposed cu alternate constructions ?? 1.25 1.45 e3 0.90 1.10 e/2 m 0.10 2x e3 2x f f note 5 f f d3 2x 2x c a b m 0.10 note 5 32x 0.40 pitch 4.70 0.58 4.70 dimensions: millimeters 0.25 32x mounting footprint 3.22 3.22 1 package outline recommended 1.92 2x 1.52 2x 1.47 2x 1.12 2x on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 CAT6500/d literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative

▲Up To Search▲

Price & Availability of CAT6500

	To Download CAT6500 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .