View EVB-EN5322QI_8281640.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

enpirion ? power datasheet en5322qi 2a powersoc synchronous buck dc- dc converter with integrated inductor general description the e n5322 is a high efficiency synchronous buck converter with integrated inductor, pwm controller, mosfets, and compensation providing the smallest possible solution size. t he 4 mhz operation allows for the use of tiny mlcc capacitors. it also enables a very wide control loop bandwidth providing excellen t transient performance and reduced output impedance. the internal compensation is designed for unconditional stability across all operating conditions . t hree vid output voltage select pins provide seven pre - programmed output voltages along with an option for external resistor divider. output voltage can be programmed on - the- fly to provide fast, dynamic voltage scaling with smooth transitions between vid programmed output voltages. applications ? point of load regulation for low power processors, network processors, dsps? fpgas and asics ? replacement of ldos ? noise sensitive applications such as a/v and rf ? computing, computer peripherals , storage, networking, and instrumentation ? dsl, stb, dvr, dtv, and ipc ordering information part number temp rating (c) package en5322qi - 40 to +85 24 - pin qfn t&r EVB-EN5322QI qfn evaluation board features ? revolutionary integrated inductor ? total solution footprint as small as 50 mm 2 ? 4 mm x 6 mm x 1.1 mm qfn package ? 4 mhz fixed switching frequency ? high efficiency, up to 9 5 % ? low ripple voltage; 8 mv p- p typical ? 2 % initial v out accuracy with vid codes ? 2% initial 0.6 v feedback voltage accuracy ? 2.4 v to 5.5 v input voltage range ? 2 a continuous output current capability ? fast transient response ? low dropout operation: 100 % duty cycle ? power ok signal with 5 ma sink capability ? dynamic voltage scaling with vid codes ? 17 a typical shutdown current ? under voltage lockout, over current, short circuit, and thermal protection ? rohs compliant; msl 3 260 c reflow application circuit en5322 10 uf 47 uf vout pvin agnd v in vsense pok vs0 vs1 vs2 enable avin pgnd c in c out 1 uf v out pgnd f igure 1. typical application circuit 1 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi absolute maximum ratings caution : absolute maximum ratings are stress ratings only. functional operation beyond recommended operating conditions is not implied. stress beyond absolute maximum ratings may cause permanent damage to the device. exposure to absolute maximum rated conditions for extended periods may affect device reliability. absolute maximum electrical ratings min m ax voltages on: p vin , avin , v out - 0.3 v 6.5 v voltages on: vsense, vs0, vs1, vs2, enable, pok - 0.3 v v in voltage on: vfb - 0.3 v 2.7 v esd rating (human body model) 2 kv esd rating (charge device model) 500 v absolute maximum thermal ratings ambient operating range - 4 0 c +85 c storage temperature range - 65 c +150 c reflow peak body temperature msl3 (10 s) +260 c thermal characteristics parameter sym bol min typ max units thermal shutdown t sd 155 c thermal shutdown hysteresis t sdh 15 c thermal resistance: junction to case (0 lfm) jc 6 c/w thermal resistance: junction to ambient (0 lfm)* ja 36 c/w * based on a 2 oz. copper board and proper thermal design in line with jedec eij - jesd51 standards recommended operating conditions parameter symbol min max units input voltage range v in 2.4 5.5 v output voltage range v out 0.6 v in - v dropout v output current i load 0 2 a operating junction temperature t j - 45 +125 c note: v dropout is defined as (i load x dropout resistance) including temperature effect . electrical characteristics v in = 5 v and t a = 25 c, unless otherwise noted. parameter sym bol test conditions min typ max units operating input voltage v in 2.4 5.5 v under voltage lockout v uvlo v in going low to high 2.2 v uvlo hysteresis 0.15 v output voltage with vid codes (note 1) v out t a = 25 c; v in = 5v i load = 100 ma vs2 vs1 vs0 vout (v) 0 0 0 3.3 0 0 1 2.5 0 1 0 1.8 0 1 1 1.5 1 0 0 1.25 1 0 1 1.2 1 1 0 0.8 - 2.0 - 2.0 - 2.0 - 2.0 - 2.0 - 2.0 - 2. 0 +2.0 +2.0 +2.0 +2.0 +2.0 +2.0 +2.0 % 2 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi parameter sym bol test conditions min typ max units v fb voltage v fb t a = 25 c; v in = 5v i load = 100 ma, vs0 = vs1 = vs2 = 1 0.588 0.60 0 0.61 2 v output voltage with vid codes (note 1) v out 2 .4 v v in 5.5 v, i load = 0 ~ 2 a, - 40c t a +85c vs2 vs1 vs0 vout (v) 0 0 0 3.3 0 0 1 2.5 0 1 0 1.8 0 1 1 1.5 1 0 0 1.25 1 0 1 1.2 1 1 0 0.8 - 3.0 - 3.0 - 3.0 - 3.0 - 3.0 - 3.0 - 3.5 +3.0 +3.0 +3.0 +3.0 +3.0 +3.0 +3.0 % vfb voltage v fb 2.4 v t a d +85c 0.582 0.600 0.618 v dynamic voltage slew rate switching between vid settings 0.975 1.5 2.025 v/ms soft start slew rate vid mode vout programming 0.975 1.5 2.025 v/ms soft start time vfb mode vout programming 0.78 1.2 1.62 ms vfb, enable, vs0 - vs2 pin input current (note 2) - 40c t a +85c +/ - 40 na enable, vs0 - vs 2 v ol t age threshold logic low logic high 0.0 1.4 0.4 v in v pok upper threshold v out rising 111 % pok upper threshold v out falling 102 % pok lower threshold v out rising 92 % pok lower threshold v out falling 90 % pok low voltage i sink = 5 ma, - 40c t a +85 c 500 na shutdown current enable low 17 t a d +85c 2. 1 3.0 a pfet on resistance 160 m ? ? ? 3 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi pin configuration figure 2 . pin diagram, top view. pin description pin n am e function 1, 2 1- 24 nc(sw) no c onnect. these pins are internally connected to the common d rain output of the i nternal mosfets . nc(sw) pins are not to be electrically connected to any external signal, ground, or voltage. however, they must be soldered to the pcb. failure to follow this guideline may result in part malfunction or damage. 2- 3, 8 -9 pgnd input/output power g round. connect these pins to the ground electrode of the input and output filter capacitors. refer to l ayout considerations section for details. 4 - 7 vout voltage and power output. connect thes e pins to output capacitor(s). 10- 12 vs2 -0 output voltage select. these pins set one of seven preset output voltages and the extern al divider option (refer to electrical characteristics table for more detail s) , and can be directly pulled up to v in or pull ed down to gnd ; these pins must not be left floating. 13 vsense sense pin for internally programmed o utput voltages with vid codes. for either vid code or external resistor divider applications , c onnect this pin to the last local output filter capacitor for internal compensation. 14 vfb feedback pin for external voltage divider network. connect a resistor divider to this pin to set the output voltage. use 340 k ? 4 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi functional block diagram voltage select dac switch vref (+) (-) error amp vsense vfb vout vs0 vs1 vs2 package boundary p-drive n-drive uvlo thermal limit current limit soft start sawtooth generator (+) (-) pwm comp pvin enable pgnd logic compensation network nc (sw) pok pok avin agnd bias figure 3. functional block diagram. 5 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi en5322 10 uf 47 uf vout pvin agnd v in vsense pok vs0 vs1 vs2 enable avin pgnd c in c out 1 uf v out pgnd r pok 100k * leave open if the pok function is not used. * r pok pok figure 4 . typical application circuit with vid codes. ( note: enable can be separated from pvin if the application requires it) typical performance characteristics circuit of figure 4 , v in = 5 v, v out = 1.2 v and t a = 25c, unless otherwise noted. top to bottom: v out = 3.3 v, 2.5 v, 1.8 v, 1.5 v, 1.2 v, 0.8 v top to bottom: v out = 2.5 v, 1.8 v, 1.5 v, 1.2 v, 0.8 v efficiency vs. load current (vin = 5.0v) 50 55 60 65 70 75 80 85 90 95 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 load current (a) efficiency (%) efficiency vs. load current (vin = 3.3v) 50 55 60 65 70 75 80 85 90 95 0.00 0.25 0. 50 0.75 1.00 1.25 1.50 1.75 2.00 load current (a) efficiency (%) 6 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi output ripple at 2 a lo ad ( ch2: v out ) v in = 3.3 v, v out = 1.2 v, c out = 1 x 47 output ripple at 2 a lo ad ( ch2: v out ) v in = 3.3 v, v out = 1.2 v, c out = 2 x 22 quiescent current (no switching) vs. input voltage 740 760 780 800 820 840 2 3 4 5 6 input voltage (v) quiescent current (ua) quiescent current (switching) vs. input voltage 8 10 12 14 16 18 2 3 4 5 6 input voltage (v) quiescent current (ma) load regulation (vin = 5 v) 1.184 1.188 1.192 1.196 1.200 1.204 1.208 0 0.4 0.8 1.2 1.6 2 load current (a) output voltage (v) load regulation (vin = 5 v) 3.284 3.288 3.292 3.296 3.300 3.304 0 0.4 0.8 1.2 1.6 2 load current (a) output voltage (v) 7 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi transient response at v in = 5 v v out = 1.2v, c out = 1 x 47 , slew rate 10a/us ) ch1 : v out, ch4: i l oad transient response at v in = 5 v v out = 3.3 v, c out = 1 x 47 , slew rate 10a/us ) ch1 : v out, ch4: i l oad v out scaling with vid codes at v in = 5 v (v out = 1.2 v ? 2.5 v , i out = 0 ? 2 a ) ch1: vs2 , ch2: v out, ch3: pok v out scaling with vid codes at v in = 3.3 v (v out = 1.2 v ? 2.5 v , i out = 0 ? 2 a ) ch1: vs2 , ch2: v out, ch3: pok power up/down at no load (v in = 5 v, v out = 1.2 v) ch1: enable , ch2: v out, ch3: pok , ch4: i inductor power up/down at 0.6 ? 8 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi output over load at no load (v in = 5 v, v out = 1.2 v) ch2: v out, ch3: pok , ch4: i inductor output over load at 2 a load (v in = 5 v, v out = 1.2 v) ch2: v out, ch3: pok , ch4: i inductor output over load at no load (v in = 5 v, v out = 1.2 v) ch2: v out, ch3: pok , ch4: i inductor output over load at 2 a load (v in = 5 v, v out = 1.2 v) ch2: v out, ch3: pok , ch4: i inductor functional description the en5322 leverages advanced cmos technology to provide high switching frequency, while also maintaining high efficiency. packaged in a 4 mm x 6 mm x 1.1 mm qfn, the en5322 provides a high degree of flexibility in circuit design while maintaining a very small footprint. hig h switching frequency allows for the use of very small mlcc input and output filter capacitors. the converter uses voltage mode control to provide high noise immunity, low output impedance and excellent load transient response. no external compensation co mponents are needed for most applications . output voltage is chosen from one of seven preset values via a three - pin vid voltage select scheme. an external divider option enables the selection of any output voltage 0.6 v. the vid pins can be toggled dyna mically to 9 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi implement glitch - free dynamic voltage scaling between any two vid preset values . pok monitors the output voltage and signals if it is within 10% of nominal. protection features include under voltage lockout (uvlo), over current protection, sho rt circuit protection, and thermal overload protection. stability over wide range of operating conditions the en5322 utilizes an internal compensation network and is designed to provide stable operation over a wide range of operating conditions. to improve transient performance or reduce output voltage ripple with dynamic loads you have the option to add supplementary capacitance to the output . when programming vout using the vid pins, t he en5322 is stable with up to 60 f of output capacitance without compensation adjustment . additional output capacitance above 60 f can be accommodated with compensation adjustment depending on the application. when programming vout with the resistor divider option, the maximum output capacitance may be limited. plea se refer to the section on soft start for more details. the high switching frequency allows for a wide control loop bandwidth. soft start the en5322qi has an internal soft - start circuit that controls the ramp of the output voltage. the control circuitry limits the v out ramp rate to levels that are safe for the power mosfets and the integrated inductor. the e n5322 qi has two soft start operating modes. when vout is programmed using a preset voltage in vid mode, the device has a constant slew rate. when the e n5322 q i is configured in external resistor divider mode, the device has a constant vout ramp time. output voltage slew rate and ramp time is given in the electrical characteristics table. excess bulk capacitance on the output of the device can cause an over - current condition at startup. when operating in vid mode, the maximum total capacitance on the output, including the output filter capacitor and bulk and decoupling capacitance, at the load, is given as: c out_total_max = c out_filter + c out _bulk = 1000uf when the e n5322 qi output voltage is programmed using and external resistor divider the maximum total capacitance on the output is given as: c out_total_max = 1. 867 x10 -3 /v out farads the above number and formula assume a no load condition at startup. over current/short circuit protection when an over current condition occurs, v out is pulled low. this condition is maintained for a period of 1.2 m s and then a normal soft start cycle is initiated. if the over current condition still persists, th is cycle will repeat. under voltage lockout an under voltage lockout circuit will hold off switching during initial power up until the input voltage reaches sufficient level to ensure proper operation. if the voltage drops below the uvlo threshold the lock out circuitry will again disable switching. hysteresis is included to prevent chattering between uvlo high and low states. enable the enable pin provides means to shut down the converter or initiate normal operation. a logic high will enable the converter to go through the soft start cycle and regulate the output voltage to the desired value . a logic low will allow the device to discharge the output and go into shutdown mode for minimal power consumption. when the output is discharged , an auxi li ary nfet tur ns on and limits the 10 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi discharge current to 3 0 0 ma or below. in shutdown mode, the device typically drains 17 a. the enable pin must not be left floating. thermal shutdown when excessive power is dissipated in the device , its junction temperature rises. once the junction temperature exceeds the thermal shutdown temperature 15 5 c , the thermal shutdown circuit turns off the converter, allowing the device to cool. when the junction temperature drops 15 c, the device will be re - enabled and go through a norm al startup process. p ower ok the en 5322 provides an open drain output to indicate if the output voltage stays within 9 2 % to 1 11 % of the set value. within this range, the pok output is allowed to be pulled high. outside this range, pok remains low. however, during transition s such as power up, power down, and dynamic voltage scaling, th e pok output will not change state until the transition is complete for enhanced noise immunity. the pok ha s 5 ma sink capability for event s where it needs to feed a digital controller with standard cmos inputs. when pok is pulled high, the pin leakage current is as low as 500 na maximum over temperature. this allows a large pull up resistor such as 100 k ? to be used for minimal current consumption in shutdown mode. the pok output can also be conveniently used as an enable input of the next stage for power sequencing of multiple converters. en5322 10 uf 47 uf vout pvin agnd v in vsense pok vs0 vs1 vs2 enable avin pgnd c in c out 1 uf v out pgnd r pok 100k * leave open if the pok function is not used. * r pok ra 340k rb vfb pok figure 5 . typical application circuit with external resistor divider . ( note: enable can be separated from pvin if the application requires it) application informatio n setting the output voltage to provide the highest degree of flexibility in choosing output voltage, the e n5322 q i us e s a 3 pin vid ( voltage id ) output voltage select arrangement. this allows the designer to choose one of seven preset voltages, or to use an external voltage divider. figure 4 shows a typical application circuit with vid codes. internally, the output of th e vid multiplexer sets the value for the voltage reference dac, which in turn is connected to the non - inverting 11 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi input of the error amplifier. this allows the use of a single feedback divider with constant loop gain and optimum compensation, independent of the output voltage selected. table 1 shows the various vs0 - vs2 pin logic states and the associated output voltage levels. a logic ?1? indicates a connection to v in or to a ?high? logic voltage level. a logic ?0? indicates a connection to ground or to a ?low? logic voltage level. these pins can be either hardwired to v in or gnd or alternatively can be driven by standard logic levels. logic low is defined as v low 0.4v. logic high is defined as v high 1.4v. any level between these two values is indeterminate. these pins must not be left floating. table 1. vid voltage select settings. vs2 vs1 vs0 v out 0 0 0 3.3v 0 0 1 2.5v 0 1 0 1.8v 0 1 1 1.5v 1 0 0 1.25v 1 0 1 1.2v 1 1 0 0.8v 1 1 1 user selectable external voltage divider as described above, the external voltage divider option is chosen by connecting the vs0, vs1, and vs2 pins to vin or logic ?high?. the en5322 qi uses a separate feedback pin, v fb , when using the external divider. vsen se must be connected to v out as indicated in figure 5 . if the external voltage divider option is chosen, use 3 4 0 k ? , 1% or better for the upper resistor ra . then the value of the bottom resistor rb in k ? is given as: ? ? = k v rb out 6.0 204 w here v out is the output voltage. rb should also be a 1% or better resistor. power - up /down sequencing during power - up, enable should not be asserted before pvin, and pvin should not be asserted before avin. the pvin should never be powered when avin is off. during power down, the avin should not be powered down before the pvin. tying pvin and avin or all three pins (avin, pvin, enable) together during power up or power down meets these requirements . pre - bias start - up the e n 5322 qi does not support startup into a pre - biased condition. be sure the output capacitors are not charged or the output of the en 5322 qi is not pre- biased when the en 5322 qi is first enabled. input and output capacitor selection low esr mlc capacitors with x5r or x7r or equivalent dielectric should be used for input and output capacitors. y5v or equivalent dielectrics lose too much capacitance with frequency, dc bias, and temperature . therefore, they are not suitable for switch - mode dc - dc converter filtering, and must be avoided. a 10 f, 10 v, 0805 mlc capacitor is needed on pvin for all applications. a 1 f, 10 v, 0 402 mlc capacitor on avin is needed for high frequency bypass to ensure clean chip supply for optimal performance . a 47 f , 6.3 v, 1 206 mlc capacitor is recommended on the output for most applications. the output ripple can be reduced by approximately 50% by using 2 x 22 f , 6.3v, 0805 mlc capacitors rather than 1 x 47 f. as described in the soft start section, there is a limitation on the maximum bulk capacitance 12 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi that can be placed on the output of this device. please refer to that section for more details. table 2. recommended input and output capacitors c in description mfg. p/n 10 f, 10v, x5r, 10%, 0805 taiyo yuden lmk212bj106kg murata grm21br71a106ke51 l panasonic ecj - 2fb1a106k c out 47 f, 6.3v, x5r, 20%, 1206 taiyo yuden jmk316bj476ml murata grm31cr60j476me19l kemet c1206c476m9pactu pok pull up resistor selection pok can be pulled up through a resistor to any voltage source as high as v in . the simplest way is to connect pok to the power input of the converter through a resistor. a 100 k ? pull up resistor is typically recommended for most applications for minimal current drain from the voltage source and good noise immunity. pok can sink up to 5 ma. 13 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi layout recommendations figure 8 . optimized layout recommendations recommendation 1: input and output filter capacitors should be placed on the same side of the pcb, and as close to the en 5322 qi package as possible. they should be connected to the device with very short and wide traces. do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. the +v and gnd traces between the capacitors and the en 5322 qi should be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. recommendation 2: the system ground plane should be the first layer immediately below the surface layer. this ground plane should be con tinuous and un - interrupted below the converter and the input/output capacitors. re comme ndation 3 : the thermal pad underneath the component must be connected to the system ground plane through as many vias as possible. the drill diameter of the vias should be 0.33mm, and the vias must have at least 1 oz. copper plating on the inside wall, making the finished hole size around 0.20 - 0.26mm. do not use thermal reliefs or spokes to connect the vias to the ground plane. this connection provides the path for heat d issipation from the converter. re comme ndation 4 : multiple small vias (the same size as the thermal vias discussed in recommendation 3) should be used to connect ground terminal of the input capacitor and output capacitors to the system ground plane. it is preferred to put these vias along the edge of the gnd copper closest to the +v copper. these vias connect the input/output filter capacitors to the gnd plane, and help reduce parasitic inductances in the input and output current loops. recommendation 5 : avin is the power supply for the small - signal control circuits. it should be connected to the input voltage at a quiet point. in figure 8 this connection is made at the input capacitor. connect a 1f capacitor from the avin pin to agnd. recommendation 6 : t he layer 1 metal under the device must not be more than shown in figure 8. see the section regarding exposed metal on bottom of package. as with any switch - mode dc/dc converter, try not to run sensitive signal or control lines underneath the converter package on other layers. re comme ndation 7: the v out sense point should be just after the last output filter capacitor. keep the sense trace short in order to avoid noise coupling into the node. re comme ndation 8 : keep r a , r b close to the vfb pin (see figures 6). the vfb pin is a high - impedance, sensitive node. keep the trace to this pin as short as possible. whenever possible, connect r b directly to the agnd pin instead of going through the gnd plane. recommendation 9 : altera provides schematic and layout reviews for all customer designs. please contact local sales representatives for references to power applications engineering support ( www.altera.com/mysupport ) . 14 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi design considerations for lead -frame based modules exposed metal pads on package bottom qfn lead - frame based package technology utilizes exposed metal pads on the bottom of the package that provide improved thermal dissipation and low package thermal resistance, smaller package footprint and thickness, large lead size and pitch, and excellent lead co - planarity. as the en5322 package is a fully integrated module consisting of multiple internal devices, the lead - frame provides circu it interconnection and mechanical support of these devices resulting in multiple exposed metal pads on the package bottom. only the two large thermal pads and the perimeter leads are to be mechanically/electrically connected to the pcb through a smt solde ring process. all other exposed metal is to remain free of any i nterconnection to the pcb. f igure 6 shows the recommended pcb metal layout for the en5322 package. a gnd pad with a solder mask "bridge" to separate into two pads and 24 signal pads are to be used to match the metal on the package. the pcb should be clear of any other metal, including traces , vias, etc., under the package to avoid electrical shorting. figure 6. recommended footprint for pcb. 15 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi package and mechanical figure 7. en5322qi pac kage d imensions 16 www.altera.com/enpirion 03454 october 11, 2013 rev f
en5322 qi contact information altera corporation 101 innovation drive san jose, ca 95134 phone: 408 -544-7000 www.altera.com ? 2013 altera corporation ? confidential. all rights reserved. altera, arria, cyclone, enpirion, hardcopy, max, megacore, nios, quartus and stratix words and logos are trademarks of altera corporation and registered in the u.s. patent and trademark offi ce and in other countries. all other words and logos identified a s trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. altera warrants performance of its semiconductor products to current specifications in accordance with altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. altera assumes no responsibil i ty or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by altera. altera customers are advised to obtain the latest version of device specifications before relying on any published informatio n and before placing orders for products or services. 17 www.altera.com/enpirion 03454 october 11, 2013 rev f

▲Up To Search▲

Price & Availability of EVB-EN5322QI

	To Download EVB-EN5322QI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .