preliminary data this is preliminary information on a new product now in deve lopment or undergoing evaluation. details are subject to change without notice. october 2009 doc id 16582 rev 1 1/10 10 STGD3HF60WD 3 a, 600 v ul tra fast igbt features minimal tail current low conduction and switching losses ultra fast soft recovery antiparallel diode applications high frequency inverters motor drives description the "hf" family is based on a new advanced planar technology concept to yield an igbt with more stable switching performance (e off ) versus temperature, as well as lower conduction losses. the STGD3HF60WD is tailo red to cost effective solution for motor drive. figure 1. internal schematic diagram 1 3 dpak tab table 1. device summary order codes marking package packaging STGD3HF60WDt4 gd3hf60wd dpak tape and reel www.st.com
electrical ratings STGD3HF60WD 2/10 doc id 16582 rev 1 1 electrical ratings table 2. absolute maximum ratings symbol parameter value unit v ces collector-emitter voltage (v ge = 0) 600 v i c (1) 1. calculated according to the iterative formula: continuous collector current at t c = 25 c tbd a i c (1) continuous collector current at t c = 100 c tbd a i cl (2) 2. vclamp = 80%,(v ces ), tj =150c, r g = 10 ? , v ge = 15 v turn-off latching current tbd a i cp (3) 3. pulse width limited by maximum junction temperature and turn-off within rbsoa pulsed collector current tbd a v ge gate-emitter voltage 20 v i f diode rms forward current at t c = 25 c 10 a i fsm surge non repetitive forward current t p =10ms sinusoidal 25 a p tot total dissipation at t c = 25 c tbd w t j operating junction temperature ? 55 to 150 c table 3. thermal data symbol parameter value unit r thj-case thermal resistance junction-case igbt tbd c/w thermal resistance junction-case diode tbd c/w r thj-amb thermal resistance j unction-ambient 100 c/w i c t c () t jmax () t c ? r thj c ? v ce sat () max () t jmax () i c t c () , () ---------------------------------------------------------------------------------------------------------- =
STGD3HF60WD electrical characteristics doc id 16582 rev 1 3/10 2 electrical characteristics (t j =25 c unless otherwise specified) table 4. static electrical characteristics symbol parameter test conditions min. typ. max. unit v (br)ces collector-emitter breakdown voltage (v ge = 0) i c = 1 ma 600 v v ce(sat) collector-emitter saturation voltage v ge = 15 v, i c = 0.5 a, t j =125c v ge = 15 v, i c = 1.5 a v ge = 15 v, i c = 1.5 a, t j =125c 1.3 2.3 1.8 v v ge(th) gate threshold voltage v ce = v ge , i c = 250 a 3.75 5.75 v i ces collector cut-off current (v ge = 0) v ce = 600 v v ce = 600 v, t j = 125 c 250 1 a ma i ges gate-emitter leakage current (v ce = 0) v ge = 20 v 100 na g fs forward transconductance v ce = 15 v , i c = 1.5 a tbd s table 5. dynamic electrical characteristics symbol parameter test conditions min. typ. max. unit c ies c oes c res input capacitance output capacitance reverse transfer capacitance v ce = 25 v, f = 1 mhz, v ge = 0 - tbd tbd tbd - pf pf pf q g q ge q gc total gate charge gate-emitter charge gate-collector charge v ce = 390 v, i c = 1.5 a, v ge = 15 v (see figure 3) - tbd tbd tbd - nc nc nc
electrical characteristics STGD3HF60WD 4/10 doc id 16582 rev 1 table 6. switching on/off (inductive load) symbol parameter test conditions min. typ. max. unit t d(on) t r (di/dt) on turn-on delay time current rise time turn-on current slope v cc = 390 v, i c = 1.5 a r g = 10 ? , v ge = 15 v (see figure 4) - tbd tbd tbd - ns ns a/s t d(on) t r (di/dt) on turn-on delay time current rise time turn-on current slope v cc = 390 v, i c = 1.5 a r g = 10 ? , v ge = 15 v, t j =125 c (see figure 4) - tbd tbd tbd - ns ns a/s t r (v off ) t d ( off ) t f off voltage rise time turn-off delay time current fall time v cc = 390 v, i c = 1.5 a, r ge = 10 ? , v ge = 15 v (see figure 4) - tbd tbd tbd - ns ns ns t r (v off ) t d ( off ) t f off voltage rise time turn-off delay time current fall time v cc = 390 v, i c = 1.5 a, r ge = 10 ? , v ge =15 v, t j = 125 c (see figure 4) - tbd tbd tbd - ns ns ns table 7. switching energy (inductive load) symbol parameter test conditions min. typ. max. unit e on (1) e off (2) e ts 1. eon is the turn-on losses when a typi cal diode is used in the test circuit in (see figure 5) . if the igbt is offered in a package with a co-pak diode, the co- pack diode is used as exte rnal diode. igbts and diode are at the same temperature (25c and 125c) 2. turn-off losses include also the tail of the collector current turn-on switching losses turn-off switching losses total switching losses v cc = 390 v, i c = 1.5 a r g = 10 ? , v ge =15 v (see figure 4) - 12 30 42 - j j j e on (1) e off (2) e ts turn-on switching losses turn-off switching losses total switching losses v cc = 390 v, i c = 1.5 a r g = 10 ? , v ge = 15 v, t j = 125 c (see figure 4) - 20 40 60 - j j j table 8. collector-emitter diode symbol parameter test conditions min. typ. max. unit v f forward on-voltage i f = 1.5 a i f = 1.5 a, tj=125 c - 1.4 1.15 1.8 v t rr q rr i rrm reverse recovery time reverse recovery charge reverse recovery current i f = 1.5 a, v r = 40 v, di/dt = 100 a/ s (see figure 5) - tbd tbd tbd ns nc a t rr q rr i rrm reverse recovery time reverse recovery charge reverse recovery current i f = 1.5 a,v r = 40 v, t j =125 c, di/dt = 100 a/ s (see figure 5) - tbd tbd tbd ns nc a
STGD3HF60WD test circuits doc id 16582 rev 1 5/10 3 test circuits figure 2. test circuit for inductive load switching figure 3. gate charge test circuit figure 4. switching waveform figure 5. diode recovery time waveform
package mechanical data STGD3HF60WD 6/10 doc id 16582 rev 1 4 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com. ecopack ? is an st trademark.
STGD3HF60WD package mechanical data doc id 16582 rev 1 7/10 dim. mm. min. typ max. a 2.20 2.40 a1 0. 9 01.10 a2 0.0 3 0.2 3 b 0.64 0. 9 0 b 4 5.20 5.40 c 0.45 0.60 c2 0.4 8 0.60 d 6.00 6.20 d1 5.10 e 6.40 6.60 e1 4.70 e2.2 8 e1 4.40 4.60 h 9 . 3 5 10.10 l1 l1 2. 8 0 l2 0. 8 0 l4 0.60 1 r0.20 v2 0 o 8 o to-252 (dpak) mechanical data 006 8 772_g
packaging mechanical data STGD3HF60WD 8/10 doc id 16582 rev 1 5 packaging mechanical data tape and reel shipment dpak footprint dim. mm inch min. max. min. max. a 330 12.992 b 1.5 0.059 c 12.8 13.2 0.504 0.520 d 20.2 0.795 g 16.4 18.4 0.645 0.724 n 50 1.968 t 22.4 0.881 base qty bulk qty 2500 2500 reel mechanical data dim. mm inch min. max. min. max. a0 6.8 7 0.267 0.275 b0 10.4 10.6 0.409 0.417 b1 12.1 0.476 d 1.5 1.6 0.059 0.063 d1 1.5 0.059 e 1.65 1.85 0.065 0.073 f 7.4 7.6 0.291 0.299 k0 2.55 2.75 0.100 0.108 p0 3.9 4.1 0.153 0.161 p1 7.9 8.1 0.311 0.319 p2 1.9 2.1 0.075 0.082 r 40 1.574 w 15.7 16.3 0.618 0.641 tape mechanical data all dimensions are in millimeters
STGD3HF60WD revision history doc id 16582 rev 1 9/10 6 revision history table 9. document revision history date revision changes 29-oct-2009 1 first release
STGD3HF60WD 10/10 doc id 16582 rev 1 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2009 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
