spec no: dsao0997 rev no: v.1a date: jan/08/2015 page: 1 of 5 approved: wynec checked: joe lee drawn:p.cheng erp: 1352000619 surface mount display attention observe precautions for handling electrostatic discharge sensitive devices part number: ACDC56-41ZGKWA-F01 green features ? 0.56 inch digit height. ? low current operation. ? excellent character appearance. ? mechanically rugged. ? gray face, white segment. ? package: 200pcs/ reel. ? moisture sensitivity level : level 2a. ? rohs compliant. package dimensions& internal circuit diagram notes: 1. all dimensions are in millimeters (inches), tolerance is 0.25(0.01")unless otherwise noted. 2. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 3.the gap between the reflector and pcb shall not exceed 0.25mm. descriptions ? the green source color devices are made with ingan on sapphire light emitting diode. ? electrostatic discharge and power surge could damage the leds. ? it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. ? all devices, equipments and machineries must be electrically grounded.
spec no: dsao0997 rev no: v.1a date: jan/08/2015 page: 2 of 5 approved: wynec checked: joe lee drawn:p.cheng erp: 1352000619 selection guide absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. dice lens type iv (ucd) [1] @ 10ma description min. typ. ACDC56-41ZGKWA-F01 green (ingan) white diffused 52000 160000 *21000 *51000 common cathode, rt. hand decimal. symbol parameter device typ. max. units test conditions peak peak wavelength green 515 nm i f =20ma d [1] dominant wavelength green 525 nm i f =20ma ? 1/2 spectral line half-width green 35 nm i f =20ma c capacitance green 45 pf v f =0v;f=1mhz v f [2] forward voltage green 3.3 4.1 v i f =20ma i r reverse current green 50 ua v r =5v parameter green units power dissipation 102.5 mw dc forward current 25 ma peak forward current [1] 150 ma reverse voltage 5 v operating / storage temperature -40c to +85c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. notes: 1. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards.
spec no: dsao0997 rev no: v.1a date: jan/08/2015 page: 3 of 5 approved: wynec checked: joe lee drawn:p.cheng erp: 1352000619 green ACDC56-41ZGKWA-F01
spec no: dsao0997 rev no: v.1a date: jan/08/2015 page: 4 of 5 approved: wynec checked: joe lee drawn:p.cheng erp: 1352000619 ACDC56-41ZGKWA-F01 recommended soldering pattern (units : mm; tolerance: 0.15) reel dimension tape specifications (units : mm)
spec no: dsao0997 rev no: v.1a date: jan/08/2015 page: 5 of 5 approved: wynec checked: joe lee drawn:p.cheng erp: 1352000619 packing & label specifications ACDC56-41ZGKWA-F01 terms and conditions for the usage of this document 1.the information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before product ion usage customer should refer to the latest datasheet for the updated specifications. 3.when using the products referenced in this docu ment, please make sure the product is being operated within the environmental and electrical limit s specified in the datasheet. if customer usage exceeds the specified limits, kingbright w ill not be responsible for any subsequent issues. 4.the information in this document applies to typical usage in consumer electronics applications. if customer's application has special reliabilit y requirements or have life-threatening liabilities, such as automotive or medical usage, please co nsult with kingbright representative for further assistance. 5.the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6.all design applications should refer to ki ngbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
