View AD7175-8_8382360.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

24 - bit, 8 - /16 - channel, 250 ksps, sigma - delta adc with true rail - to - rail buffers data sheet ad7175 - 8 rev. 0 document feedback information furnished by analog devices is believed to be accurate and reliable. however, no responsibilit y is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any pat ent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062 - 9106, u.s.a. tel: 781.329.4700 ? 2015 analog de vices, inc. all rights reserved. technical support www.analog.com features fast and flexible output rate: 5 sps to 250 ksps channel scan data rate of 50 ksps/channel (20 s settling) performance specifications 17.2 noise free bits at 250 ksps 20.2 noise free bits at 2.5 ksps 24 noise free bits at 20 sps inl: 1 ppm of fsr 85 db filter rejection of 50 hz and 60 hz with 50 ms settling user configurable input channels 8 fully differential channels or 16 single - ended channels crosspoint multiplexer on - chip 2.5 v reference (2 ppm/c drift) true rail - to - rail analog and reference input buffers internal or external clock power supply: avdd1 ? avss = 5 v, avdd2 = iovdd = 2 v to 5 v (nominal) split supply with avdd1/avss at 2.5 v adc current: 8.4 ma temperature range: ?40c to +105c 3 - or 4 - wire serial digital interface (schmitt trigger on sclk) serial port interface (spi), qspi, microwire, and dsp compatible applications process control: plc/dcs modules temperature and pressure measurement medical a nd scientific multichannel instrumentation chromatography general description the ad7175 - 8 is a low noise, fast settling, multiplexed , 8 - /16 - channel (fully/pseudo differential) - analog - to - digital converter (adc) for low bandwidth inputs. it has a maximum channel scan rate of 50 ksps (20 s) for fully settled data. the output data rates range from 5 sps to 250 ksps. the ad7175 - 8 integrates key analog and digital signal condition - ing blocks to allow users to configure an individual setup for each analog input channel in use. each feature can be user selected on a per channel basis. integrated true rail - to - rail buffers on the analog inputs and external reference inputs provide easy to drive high impedance inputs. the precision 2.5 v low drift (2 ppm/c) band gap internal reference (with output reference buffer) adds embedded functionality to reduce external component count. the digital filter allows simultaneous 50 hz and 60 hz rejection at a 27.27 sps output data rate. the user can switch between different filter options according to the demands of each channel in the application. the adc automatically switches through each selected channel. further digital processing functions include offset and gain calibration registers, configurable on a per channel basis. the device o perates with a 5 v avdd1 ? avs s supply , or with 2.5 v av dd1/ avs s, and 2 v to 5 v avdd2 and iovdd nominal supplies. the specified operating temperature range is ?40c to +105c. the ad7175 - 8 is available in a 40- lead lfcsp package. functional block dia gram figure 1. avdd1 avdd analog input buffers reference input buffers avss avss pdsw dgnd ref? ref+ refout avdd2 regcapa ain0/ref2? ain1/ref2+ ain15 ain16 - adc 1.8v ldo crosspoint multiplexer 1.8v ldo int ref temperature sensor iovdd regcapd serial interface and control digital filter AD7175-8 buffered precision reference sclk din cs dout/rdy sync error xtal1 xtal2/clkio xtal and internal clock oscillator circuitry gpio0 gpio1 gpo2 gpo3 i/o and external mux control 129 1 1-001
ad7175- 8 data sheet rev. 0 | page 2 of 64 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general descript ion ......................................................................... 1 functional block diagram .............................................................. 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 timing characteristics ................................................................ 6 absolute maximum ratings ............................................................ 8 thermal resistance ...................................................................... 8 esd caution .................................................................................. 8 pin configuration and function descriptions ............................. 9 typical performance characteristics ........................................... 11 noise performance and resolution .............................................. 17 getting started ................................................................................ 18 power supplies ............................................................................ 19 digital commun ication ............................................................. 19 ad7175 - 8 reset .......................................................................... 20 configuration overview ........................................................... 20 circuit description ......................................................................... 25 buffered analog input ............................................................... 25 crosspoint multiplexer .............................................................. 25 ad7175 - 8 reference .................................................................. 26 buffered reference input ........................................................... 27 cloc k source ............................................................................... 27 digital filters ................................................................................... 28 sinc5 + sinc1 filter ..................................................................... 28 sinc3 filter ................................................................................... 28 single cycle settling ................................................................... 29 enhanced 50 hz and 60 hz rejection f ilters ......................... 33 operating modes ............................................................................ 36 continuous conversion mode ................................................. 36 continuous read mode ............................................................. 37 single conversion mode ........................................................... 38 standby and power - down modes ............................................ 39 calibration ................................................................................... 39 digital interface .............................................................................. 40 checksum protection ................................................................. 40 crc calculation ......................................................................... 41 integrated functions ...................................................................... 43 general - purpose i/o ................................................................. 43 external multiplexer control ................................................... 43 delay ............................................................................................ 43 16- bit/24 - bit conversi ons ......................................................... 43 dout_reset ........................................................................... 43 synchronization .......................................................................... 43 error flags ................................................................................... 44 data_stat ............................................................................... 4 4 iostrength ........................................................................... 44 power - down switch .................................................................. 45 internal temperature sensor .................................................... 45 grounding and layout .................................................................. 46 register summary .......................................................................... 47 register details ............................................................................... 49 communications register ......................................................... 49 stat us register ............................................................................. 51 adc mode register ................................................................... 52 interface mode register ............................................................ 53 register check ............................................................................ 54 data register ............................................................................... 54 gpio configuration register ................................................... 55 id register ................................................................................... 56 channel register 0 ..................................................................... 56 channel re gister 1 to channel register 15 ............................ 58 setup configuration register 0 ................................................ 59 setup configuration register 1 to setup configuration register 7 ..................................................................................... 60 filter configuration register 0 ................................................. 61 filter configuration register 1 to filter configuration re gister 7 ..................................................................................... 62 offset register 0 ......................................................................... 62 offset register 1 to offset register 7 ....................................... 62 gain register 0 ............................................................................ 62 gain register 1 to gain register 7 ........................................... 63 outline dimensions ....................................................................... 64 ordering guide .......................................................................... 64 revision history 10 /15 revision 0: initial version
data sheet ad7175- 8 rev. 0 | page 3 of 64 specifications av dd 1 = 4.5 v to 5.5 v, av d d 2 = 2 v to 5.5 v, i o v d d = 2 v to 5.5 v, avss = dgnd = 0 v, ref+ = 2.5 v, ref? = avss, internal master clock (mclk) = 16 mhz, t a = t min to t max (?40c to +105c), unless otherwise noted. table 1 . parameter test conditions/comments min typ max unit adc speed and performance output data rate (odr) 5 250,000 sps no missing codes 1 excluding sinc3 filter 125 ksps 24 bits resolution see table 19 to table 23 noise see table 19 to table 23 accuracy integral nonlinearity (inl) all input buffers enabled 4 .5 10 p pm of fsr all input buffers disabled 1 4 .5 ppm of fsr offset error 2 internal short 60 v offset drift internal short 1 5 0 nv/c gain error 2 8 0 110 ppm of fsr gain drift 1 0. 5 0.75 ppm/c rejection power supply rejection avdd1, avdd2, for v in = 1 v 9 0 db common - mode rejection v in = 0.1 v at dc 95 db at 50 hz, 60 hz 1 20 hz output data rate (post filter), 50 hz 1 hz and 60 hz 1 hz 120 db normal mode rejection 1 50 hz 1 hz and 60 hz 1 hz internal clock, 20 sps odr (postfilter) 71 90 db external clock, 20 sps odr (postfilter) 85 90 db analog inputs differential input range v ref = (ref+) ? (ref?) v ref v absolute voltage limits 1 input buffers disabled avss ? 0.05 avdd1 + 0.05 v input buffers enabled avss avdd1 v analog input current input buffers disabled input current 48 a/v input current drift external clock 0.75 na/v/c internal clock 4 na/v/c input buffers enabled input current 3 0 na input current drift avdd1 ? 0.2 v to avss + 0.2 v 7 5 pa/c avdd1 to avss 1 na/c crosstalk 1 khz input ?120 db internal reference 100 nf external capacitor to avss output voltage refout, with respect to avss 2.5 v initial accuracy 3 refout, t a = 25c ?0.12 +0.12 % of v temperature coefficient 1 0c to 105c 2 5 ppm/c ? 40c to +105c 3 10 ppm/c reference load current, i load ?10 +10 ma power supply rejection avdd1, avdd2 (line regulation) 9 5 db load regulation ?v out /?i load 32 ppm/ma voltage noise e n , 0.1 hz to 10 hz, 2.5 v reference 4.5 v rms voltage noise density e n , 1 khz, 2.5 v reference 215 nv/hz
ad7175- 8 data sheet rev. 0 | page 4 of 64 parameter test conditions/comments min typ max unit turn - on settling time 100 nf refout capacitor 200 s short - circuit current, i sc 25 ma external reference inputs differential input range v ref = (ref+) ? (ref?) 1 2.5 avdd1 v absolute voltage limits 1 input buffers disabled avss ? 0.05 avdd1 + 0.05 v input buffers enabled avss avdd1 v ref+/ref? input current input buffers disabled input current 72 a/v input current drift external clock 1.2 na/v/c internal clock 6 na/v/c input buffers enabled input current 800 na input current drift 1.2 na/c normal mode rejection 1 see the rejection parameter common - mode rejection 95 db temperature sensor accuracy after user calibration at 25c 2 c sensitivity 470 v/k burnout currents source/sink current analog input buffers must be enabled 10 a power - down switch r on 24 allowable currents 16 ma general - purpose i nputs /o utputs (gpio0, gpio1, gpo2, gpo3 ) with respect to avss input mode leakage current 1 ?10 +10 a floating state output capacitance 5 pf output high voltage, v oh 1 i source = 200 a avss + 4 v output low voltage, v ol 1 i sink = 800 a avss + 0.4 v input high voltage, v i n h 1 avss + 3 v input low voltage, v i n l 1 avss + 0.7 v clock internal clock frequency 16 mhz accuracy ?2.5% +2.5% % duty cycle 50 % output low voltage, v ol 0.4 v output high voltage, v oh 0.8 iovdd v crystal frequency 14 16 16.384 mhz start - up time 10 s external clock (clkio) 16 16.384 mhz duty cycle 1 30 50 70 %
data sheet ad7175- 8 rev. 0 | page 5 of 64 parameter test conditions/comments min typ max unit logic inputs input high voltage, v inh 1 2 v iovdd < 2.3 v 0.65 iovdd v 2.3 v iovdd 5.5 v 0.7 iovdd v input low voltage, v inl 1 2 v iovdd < 2.3 v 0.35 iovdd v 2.3 v iovdd 5.5 v 0.7 v hysteresis 1 iovdd 2.7 v 0.08 0.25 v iovdd < 2.7 v 0.04 0.2 v leakage current ?10 +10 a logic output (dout/ rdy ) output high voltage, v oh 1 iovdd 4.5 v, i source = 1 ma 0.8 iovdd v 2.7 v iovdd < 4.5 v, i source = 500 a 0.8 iovdd v iovdd < 2.7 v, i source = 200 a 0.8 iovdd v output low voltage, v ol 1 iovdd 4.5 v, i sink = 2 ma 0.4 v 2.7 v iovdd < 4.5 v, i sink = 1 ma 0.4 v iovdd < 2.7 v, i sink = 400 a 0.4 v leakage current floating state ?10 +10 a output capacitance floating state 10 pf system calibration 1 full - scale (fs) calibration limit 1.05 fs v zero - scale calibration limit ?1.05 fs v input span 0.8 fs 2.1 fs v power requirements power supply voltage avdd1 to avss 4.5 5 5.5 v avdd2 to avss 4 2 2.5 to 5 5.5 v avss to dgnd ? 2.75 0 v iovdd to dgnd 4 2 2.5 to 5 5.5 v iovdd to avss for avss < dgnd 6.35 v power supply currents 5 all outputs unloaded, digital inputs connected to iovdd or dgnd full operating mode avdd1 current analog input and reference input buffers (ain, ref) disabled, external reference 1.4 1.65 ma analog input and reference input buffers disabled, internal reference 1.75 2 ma analog input and reference input buffers enabled , external reference 13 16 ma each buffer: ain+, ain ? , ref+, ref ? 2.9 ma avdd2 current external reference 4.5 5 ma internal reference 4.75 5.2 ma iovdd current external clock 2.5 2.8 ma internal clock 2.75 3.1 ma external crystal 3 ma standby mode (ldo on) internal reference off, total current consumption 30 a internal reference on, total current consumption 425 a power - down mode full power - down (including ldo and internal reference) 5 10 a
ad7175- 8 data sheet rev. 0 | page 6 of 64 parameter test conditions/comments min typ max unit power dissipation 5 full operating mode all buffers disabled, external clock and reference, avdd2 = 2 v, iovdd = 2 v 21 mw all buffers disabled, external clock and reference, all supplies = 5 v 42 mw all buffers disabled, external clock and reference, all supplies = 5.5 v 52 mw all buffers enabled, internal clock and reference, avdd2 = 2 v, iovdd = 2 v 82 mw all buffers enabled, internal clock and reference, all supplies = 5 v 105 mw all buffers enabled, internal clock and reference, all supplies = 5.5 v 136 mw standby mode internal reference off, all supplies = 5 v 1 50 w internal reference on, all supplies = 5 v 2.2 mw power - down mode full power - down, all supplies = 5 v 25 50 w 1 this s pecification is not production tested but is supported by characterization data at the initial product release . 2 following a system or internal zero - scale calibration, the offset error is in the order of the noise for the programmed output data rate selected. a system full - scale calibration reduces the gain error to the order of the noise for the programmed output data rate. 3 this specification i nclud es moisture sensitivity level (msl) pre conditioning effects. 4 the nominal range is 2 v to 5 v . 5 this specification is with no load on the refout and digital output pins. timing characteristi cs iovdd = 2 v to 5.5 v, dgnd = 0 v, input logic 0 = 0 v, input logic 1 = iovdd, c load = 20 pf, unless otherwise noted. table 2 . parameter limit at t min , t max unit description 1 , 2 sclk t 3 25 ns min sclk high pulse width t 4 25 ns min sclk low pulse width read operation t 1 0 ns min cs falling edge to dout/ rdy active time 15 ns max iovdd = 4.75 v to 5.5 v 40 ns max iovdd = 2 v to 3.6 v t 2 3 0 ns min sclk active edge to data valid delay 4 12.5 ns max iovdd = 4.75 v to 5.5 v 25 ns max iovdd = 2 v to 3.6 v t 5 5 2.5 ns min bus relinquish time after cs inactive edge 20 ns max t 6 0 ns min sclk inactive edge to cs inactive edge t 7 10 ns min sclk inactive edge to dout/ rdy high/low write operation t 8 0 ns min cs falling edge to sclk active edge setup time 4 t 9 8 ns min data valid to sclk edge setup time t 10 8 ns min data valid to sclk edge hold time t 11 5 ns min cs rising edge to sclk edge hold time 1 sample tested during initial release to ensure compliance. 2 see figure 2 and figure 3 . 3 th is parameter is defined as the time required for the output to cross the v ol or v oh limits. 4 the sclk active edge is the falling edge of sclk. 5 dout/ rdy returns high after a read of the data register. in single conversion mode and continuous conversion mode, the same data can b e read again, if required, while dout/ rdy is high, although care must be taken to ensure that subsequent re ads do not occur close to the next output update. if the continuous read feature is enabled, the digital word can be read only once.
data sheet ad7175- 8 rev. 0 | page 7 of 64 timing diagrams figure 2 . read cycle timing diagram figure 3 . write cycle timing diagram t 2 t 3 t 4 t 1 t 6 t 5 t 7 cs (i) dout/rdy (o) sclk (i) i = input, o = output msb lsb 129 1 1-003 i = input, o = output cs (i) sclk (i) din (i) msb lsb t 8 t 9 t 10 t 11 129 1 1-004
ad7175- 8 data sheet rev. 0 | page 8 of 64 absolute maximum rat ings t a = 25c, unless otherwise noted. table 3 . parameter rating avdd1, avdd2 to avss ?0.3 v to +6.5 v avdd1 to dgnd ?0.3 v to +6.5 v iovdd to dgnd ?0.3 v to +6.5 v iovdd to avss ?0.3 v to +7.5 v avss to dgnd ?3.25 v to +0.3 v analog input voltage to avss ?0.3 v to avdd1 + 0.3 v reference input voltage to avss ?0.3 v to avdd1 + 0.3 v digital input voltage to dgnd ?0.3 v to iovdd + 0.3 v digital output voltage to dgnd ?0.3 v to iovdd + 0.3 v analog input/digital input current 10 ma operating temperature range ?40c to +105c storage temperature range ?65c to +150c maximum junction temperature 150c lead soldering, reflow temperature 260c esd rating (h uman b ody m odel ) 4 kv stresses at or above those listed under absolute maximum ratings may cause permanent damage to the product. this is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. operation beyond the maximum operating conditions for extended periods may affect product reliability. thermal resistance ja is specified for a device soldered on a jedec test board for surface - mount packages. table 4 . thermal resistance package type ja unit 40 - lead, 6 mm 6 mm lfcsp 1 - layer jedec board 114 c/w 4 - layer jedec board 54 c/w 4 - layer jedec board with 16 thermal vias 34 c/w esd caution
data sheet ad7175- 8 rev. 0 | page 9 of 64 pin configuration an d function descripti ons figure 4 . pin configuration table 5 . pin function descriptions 1 pin no. mnemonic type 2 description 1 ain16 ai analog input 16. this pin is s electable through the crosspoint mu ltiplexer . 2 ain0/ref2? ai analog input 0 (ain0)/reference 2, negative input (ref2?). an external reference can be applied between ref2+ and ref2 ? . ref2 ? can span from avss to avdd1 ? 1 v. analog input 0 is selectable through the crosspoint multiplexer . reference 2 can be selected through the ref _ sel x bits in the setup configuration register s . 3 ain1/ref2+ ai analog input 1 (ain0)/reference 2, positive input (ref2+). an external reference can be applied between ref2+ and ref2 ? . ref2+ span s from avdd1 to avss + 1 v . analog input 1 is selectable through the crosspoint multiplexer . reference 2 can be selected through the ref_selx bits in the setup configuration register s . 4 ain2 ai analog input 2. this pin is s electable through the crosspoint multiplexer. 5 ain3 ai analog input 3. this pin is selectable through the crosspoint multiplexer. 6 refout ao buffered output of internal reference. the output is 2.5 v with respect to avss. 7 regcapa ao analog low dropout ( ldo ) regulator output. decouple this pin to avss using a 1 f capacitor. 8 avss p negative analog supply. this supply ranges from 0 v to ?2.75 v and is nominally set to 0 v. 9 avdd1 p analog supply voltage 1. this voltage is 5 v 10% with respect to avss. avdd1 ? avss can be a single 5 v supply or a 2.5 v split supply. 10 avdd2 p analog supply voltage 2. this voltage ranges from 2 v to avdd1 with respect to avss. 11 pdsw ao power - down switch connected to avss. this pin is controlled by the pdsw bit in the gpiocon register. 12 xtal1 ai input 1 for crystal. 13 xtal2/clkio ai/di input 2 for crystal (xtal2)/clock input or output (clkio). see the clocksel bit settings in the adcmode register for more information. 14 dout/ rdy do serial data output (dout)/data ready output ( rdy ). this pin serves a dual purpose. it functions as a serial data output pin to access the output shift register of the adc. the output shift register can contain data from any of the on - chip data o r control registers. the data - word/control word information is placed on the dout/ rdy pin on the sclk falling edge and is valid on the sclk rising edge. when cs is high, the dout/ rdy output is tristated . when cs is low, and a register is not being read, dout/ rdy operates as a data ready pin, going low to indicate the completion of a conversion. if the data is not read after the conversion, the pin goes high before the next update occurs. the dout/ rdy falling edge can be used as an interrupt to a processor, indicating that valid data is available. 1 ain16 2 ain0/ref2? 3 ain1/ref2+ 4 ain2 5 ain3 6 refout 7 regcapa notes 1. solder the exposed pad to a similar pad on the pcb under the exposed pad to confer mechanical strength and for heat dissipation. the exposed pad must be connected to avss through this pad on the pcb. 8 avss 9 avdd1 10 avdd2 23 gpio0 24 gpio1 25 gpo2 26 ain4 27 ain5 28 ain6 29 ain7 30 ain8 22 regcapd 21 dgnd 1 1 pdsw 12 xtal1 13 xtal2/clkio 15 din 17 cs 16 sclk 18 error 19 sync 20 iovdd 14 dout/rdy 33 ain11 34 ain12 35 ain13 36 ain14 37 ain15 38 gpo3 39 ref? 40 ref+ 32 ain10 31 ain9 top view (not to scale) AD7175-8 12911-005
ad7175- 8 data sheet rev. 0 | page 10 of 64 pin no. mnemonic type 2 description 15 din di serial data input to the input shift register on the adc. data in this shift register is transferred to the control registers in the adc, with the register address (ra) bits of the communications register identifying the appropriate register. data is clocked in on the rising edge of sclk. 16 sclk di serial clock input. this serial clock input is for data transfers to and from the adc. sclk has a schmitt trigger ed input, making the interface suitable for opto - isolated applications. 17 cs di chip select input. this pin is an active low logic input used to select the adc. use cs to select the adc in systems with more than one device on the serial bus. cs can be hardwired low, allowing the adc to operate in 3 - wire mode with sclk, din, and dout / rdy used to interface with the d evice. when cs is high, the dout/ rdy output is tristated. 18 error di/o error input/output or general - purpose output. this pin can be used in one of the following three modes: active low error input mode. this mode sets the adc_error bit in the status register. active low, open - drain error output mode. the status register error bits are mapped to the error pin. the error pins of multiple devices can be wired together to a common pull - up resistor so that an error on any device can be observed. general - purpose output mode. the status of the pin is controlled by the err_dat bit in the gpiocon register. the pin is referenced between iovdd and dgnd, as opposed to the avdd1 and avss levels used by the gpio1 and gpio2 pins. the error pin has an active pull - up circuit in this case. 19 sync di synchronization input. allows synchronization of the digital filters and analog modulators when using multiple ad7175 -8 devices. 20 iovdd p digital i/o supply voltage. the iovdd voltage ranges from 2 v to 5 v (nominal) . iovdd is independent of avdd1 and avdd2. for example, iovdd can be operated at 3.3 v when avdd1 or avdd2 equals 5 v, or vice versa. if avss is set to ?2.5 v, the voltage on iovdd must not exceed 3.6 v. 21 dgnd p digital ground. 22 regcapd ao digital ldo regulator output. this pin is for decoupling purposes only. decouple this pin to dgnd using a 1 f capacitor. 23 gpio0 di/o general - purpose input/output 0 . logic input/output on this this pin is referred to the avdd1 and avss supplies. 24 gpio1 di/o general - purpose input/output 2 . logic input/output on this this pin is referred to the avdd1 and avss supplies. 25 gpo2 do general - purpose output 2 . logic output on this this pin is referred to the avdd1 and avss supplies. 26 ain4 ai analog input 4. this pin is selectable through the crosspoint multiplexer. 27 ain5 ai analog input 5. this pin is selectable through the crosspoint multiplexer. 28 ain6 ai analog input 6. this pin is selectable through the crosspoint multiplexer. 29 ain7 ai analog input 7. this pin is selectable through the crosspoint multiplexer. 30 ain8 ai analog input 8. this pin is selectable through the crosspoint multiplexer. 31 ain9 ai analog input 9. this pin is selectable through the crosspoint multiplexer. 32 ain10 ai analog input 10. this pin is selectable through the crosspoint multiplexer. 33 ain11 ai analog input 11. this pin is selectable through the crosspoint multiplexer. 34 ain12 ai analog input 12. this pin is selectable through the crosspoint multiplexer. 35 ain13 ai analog input 13. this pin is selectable through the crosspoint multiplexer. 36 ain14 ai analog input 14. this pin is selectable through the crosspoint multiplexer. 37 ain15 ai analog input 15. this pin is selectable through the crosspoint multiplexer. 38 gpo3 do general - purpose output 3 . logic output on this this pin is referred to the avdd1 and avss supplies. 39 ref? ai reference 1 input negative terminal. ref? can span from avss to avdd1 ? 1 v. reference 1 can be selected through the ref_selx bits in the setup configuration register s . 40 ref+ ai reference 1 input positive terminal. an external reference can be applied between ref+ and ref?. ref+ can span from avdd1 to avss + 1 v. reference 1 can be selected through the ref_selx bits in the setup configuration register s . ep p exposed pad. solder t he exposed pad to a similar pad on the pcb under the exposed pad to confer mechanical strength to the package and for heat dissipation. the exposed pad must be connected to avss through this pad on the pcb. 1 note that, throughout this data sheet, the dual function pin names are referenced by the relevant function only. 2 ai = analog input, ao = analog o utput , p = power s upply , di = digital input, do = digital output, and di/o = bidirectional digital input/output .
data sheet ad7175- 8 rev. 0 | page 11 of 64 typical performan ce characteristics avdd1 = 5 v, avdd2 = 5 v, iovdd = 3.3 v, t a = 25c, unless otherwise noted. figure 5 . noise (analog input buffers disabled, v ref = 5 v, output data rate = 5 sps) figure 6 . noise (analog input buffers disabled, v ref = 5 v, output data rate = 10 ksps) figure 7 . noise (analog input buffers disabled, v ref = 5 v, output data rate = 250 ksps) figure 8 . histogram (analog input b uffers disabled, v ref = 5 v, output data rate = 5 sps) figure 9 . histogram (analog input buffers disabled, v ref = 5 v, output data rate = 10 ksps) figure 10 . histogram (analog input buffers disabled, v ref = 5 v, output data rate = 250 ksps) 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8386000 8386500 8387000 8387500 8388000 8388500 8389000 8389500 8390000 129 1 1-205 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8388445 8388450 8388455 8388460 8388465 8388470 8388475 8388480 129 1 1-206 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8388400 8388420 8388440 8388460 8388480 8388500 8388520 129 1 1-207 sample count adc code 0 1000 900 800 700 600 500 400 300 200 100 8388460 8388461 8388462 8388463 8388464 8388465 8388466 129 1 1-208 sample count adc code 0 120 100 80 60 40 20 8388450 8388451 8388452 8388453 8388454 8388455 8388456 8388457 8388458 8388459 8388460 8388461 8388462 8388463 8388464 8388465 8388466 8388467 8388468 8388469 8388470 8388471 8388472 8388473 8388474 8388475 8388476 8388477 129 1 1-209 sample count adc code 0 45 40 35 30 25 20 15 10 5 129 1 1-210 8388420 8388422 8388424 8388426 8388428 8388430 8388432 8388434 8388436 8388438 8388440 8388442 8388444 8388446 8388448 8388450 8388452 8388454 8388456 8388458 8388460 8388462 8388464 8388466 8388468 8388470 8388472 8388474 8388476 8388478 8388480 8388482 8388484 8388486 8388488 8388490 8388492 8388494 8388496 8388498 8388500 8388502 8388504
ad7175- 8 data sheet rev. 0 | page 12 of 64 figure 11 . noise (analog input buffers enabled, v ref = 5 v, output data rate = 5 sps) figure 12 . noise (analog input buffers enabled, v ref = 5 v, output data rate = 10 ksps) figure 13 . noise (analog input buffers enabled, v ref = 5 v, output data rate = 250 ksps) figure 14 . histogram (analog input buffers enabled, v ref = 5 v, output data rate = 5 sps) figure 15 . histogram (analog input buffers enabled, v ref = 5 v, output data rate = 10 ksps) figure 16 . histogram (analog input buffers enabled, v ref = 5 v, output data rate = 250 ksps) 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8385000 8385500 8386000 8386500 8387000 8387500 8388000 8388500 8389000 8389500 8390000 129 1 1-2 1 1 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8388480 8388485 8388490 8388495 8388500 8388505 8388510 8388515 8388520 129 1 1-212 0 1000 900 800 700 600 500 400 300 200 100 adc code sample number 8388440 8388460 8388480 8388500 8388520 8388540 8388560 8388580 129 1 1-213 sample count adc code 0 1000 900 800 700 600 500 400 300 200 100 8388490 8388491 8388492 8388493 8388494 8388495 8388496 129 1 1-214 129 1 1-215 sample count adc code 0 10 20 30 40 50 60 70 80 90 100 8388480 8388481 8388482 8388483 8388484 8388485 8388486 8388487 8388488 8388489 8388490 8388491 8388492 8388493 8388494 8388495 8388496 8388497 8388498 8388499 8388500 8388501 8388502 8388503 8388504 8388505 8388506 8388507 8388508 8388509 8388510 8388511 8388512 8388513 8388514 129 1 1-216 sample count adc code 0 35 30 25 20 15 10 5 8388460 8388462 8388464 8388466 8388468 8388470 8388472 8388474 8388476 8388478 8388480 8388482 8388484 8388486 8388488 8388490 8388492 8388494 8388496 8388498 8388500 8388502 8388504 8388506 8388508 8388510 8388512 8388514 8388516 8388518 8388520 8388522 8388524 8388526 8388528 8388530 8388532
data sheet ad7175- 8 rev. 0 | page 13 of 64 figure 17 . noise vs. input common - mode voltage, analog input buffers on and off figure 18 . noise vs. external master clock frequency, analog input buffers on and off figure 19 . internal reference settling time figure 20 . common - mode rejection ratio (cmrr) vs. v in frequency (v in = 0.1 v, output data rate = 250 ksps) figure 21 . common - mode rejection ratio (cmrr) vs. v in frequency (v in = 0.1 v, 10 hz to 70 hz, output data rate = 20 sps , enhanced filter) figure 22 . power supply rejection ratio (psrr) vs. v in frequency 0 0.000002 0.000004 0.000006 0.000008 0.000010 0.000012 0.000014 0.000016 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 noise (v) input common-mode voltage (v) analog input buffers on analog input buffers off 129 1 1-217 0 2 4 6 8 10 12 14 16 noise (v rms) frequency (mhz) 0 2 4 6 8 10 12 14 16 18 20 analog input buffers off analog input buffers on 129 1 1-218 1 10k 1k 100 10 output code sample number 16660000 16680000 16700000 16720000 16740000 16760000 16780000 16800000 continuous conversion?reference disabled standby?reference disabled standby?reference enabled 129 1 1-225 1 1m 100k 10k 1k 100 10 cmrr (db) v in frequency (hz) ?120 ?100 ?80 ?60 ?40 ?20 0 129 1 1-226 10 70 60 50 40 30 20 cmrr (db) v in frequency (hz) ?180 ?170 ?160 ?150 ?140 ?130 ?120 ?110 ?100 ?90 ?80 129 1 1-227 1 10 100 1k 10k 100k 1m 10m 100m psrr (db) v in frequency (hz) ?130 ?120 ?110 ?100 ?90 ?60 ?70 ?80 avdd1?external 2.5v reference avdd1?internal 2.5v reference 129 1 1-228
ad7175- 8 data sheet rev. 0 | page 14 of 64 figure 23 . integral nonlinearity (inl) vs. v in (differential input , external 2.5 v reference ) figure 24 . integral nonlinearity (inl) vs. v in (differential input, external 5 v reference) figure 25 . integral nonlinearity (inl) vs. v in (differential input, internal 2.5 v reference) figure 26 . integral nonlinearity (inl) distribution histogram (all input buffers disabled, differential input, v ref = 5 v external, 92 units) figure 27 . internal oscillator frequency/accuracy distribution histogram (100 units) figure 28 . internal oscillator frequency vs. temperature 5 ?5 ?4 ?3 ?2 ?1 0 1 2 3 4 ?2.5 ?1.5 ?0.5 0.5 1.5 2.5 inl (ppm/fsr) v in (v) int osc buffers off int osc buffers on ext crystal buffers off ext crystal buffers on ext clk buffers off ext clk buffers on 129 1 1-023 6 ?6 ?4 ?2 0 2 4 ?5 5 inl (ppm/fsr) v in (v) int osc buffers off int osc buffers on ext crystal buffers off ext crystal buffers on ext clk buffers off ext clk buffers on 12911-024 ?4 ?3 ?2 ?1 0 1 2 3 4 25 ?20 ?15 ?10 ?5 0 5 10 15 20 ?2.5 ?1.5 ?0.5 0.5 1.5 2.5 inl (ppm/fsr) v in (v) int osc buffers off int osc buffers on ext crystal buffers off ext crystal buffers on ext clk buffers off ext clk buffers on 129 1 1-025 16 14 12 10 8 6 4 2 0 sample count inl error (ppm) 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 129 1 1-029 sample count frequency (mhz) 0 5 10 15 50 45 40 35 30 25 20 15.98 15.99 16.00 16.01 16.02 16.03 16.04 16.05 129 1 1-235 ?40 ?20 0 20 40 60 80 100 frequency (hz) temperature (c) 15600000 15700000 15800000 15900000 16000000 16100000 16200000 16300000 16400000 129 1 1-236
data sheet ad7175- 8 rev. 0 | page 15 of 64 figure 29 . absolute reference error vs. temperature figure 30 . offset error distribution histogram (internal short , 92 units) figure 31 . offset error drift distribution histogram (internal short , 92 units) figure 32 . gain error distribution histogram (all input buffers enabled , 611 units) figure 33 . gain error distribution histogram (all input buffers disabled, 647 units) figure 34 . gain error drift distribution histogram (all input buffers enabled, 79 units) reference error (v) temperature (c) 129 1 1-237 ?1500 ?1000 ?500 0 500 1000 1500 ?60 ?50 ?40 ?30 ?20 ?10 0 10 20 30 40 50 60 70 80 90 100 110 120 device 1 device 2 device 3 35 30 20 25 15 10 5 0 sample count offset error (v) ?74 ?70 ?66 ?62 ?58 ?54 ?50 ?46 ?42 ?38 ?30 ?34 129 1 1-034 14 12 8 10 6 4 2 0 sample count offset drift (nv/c) 0 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 190 200 129 1 1-035 160 140 120 80 100 60 40 20 0 sample count gain error (ppm of fsr) ?1.0 ?0.8 ?0.6 ?0.4 ?0.2 0 0.2 0.4 0.6 0.8 1.0 1.4 1.2 129 1 1-036 160 140 120 80 100 60 40 20 0 sample count gain error (ppm of fsr) 74 75 76 77 78 79 80 81 82 83 84 85 129 1 1-037 20 16 18 14 12 8 10 6 4 2 0 sample count gain error drift (ppm of fsr/c) ?0.40 ?0.36 ?0.32 ?0.28 ?0.24 ?0.20 ?0.16 ?0.12 ?0.08 ?0.04 0 129 1 1-038
ad7175- 8 data sheet rev. 0 | page 16 of 64 figure 35 . gain error drift over temperature distribution histogram (all input buffers disabled, 79 units) figure 36 . supply current vs. temperature (continuous conversion mode) figure 37 . supply current vs. temperature ( standby mode with reference enabled ) figure 38 . temperature sensor distribution histogram (uncalibrated, 100 units) figure 39 . burnout current distribution histogram (100 units) figure 40 . analog input current vs. input voltage (v cm = 2.5 v) 18 16 14 12 8 10 6 4 2 0 sample count gain error drift (ppm of fsr/c) ?0.14 ?0.10 ?0.06 ?0.02 0.02 0.06 0.10 0.14 0.18 0.22 0.26 129 1 1-039 ?40 ?20 0 20 40 60 80 100 supply current (ma) temperature (c) 0 25 20 15 10 5 all input buffers off all input buffers on 129 1 1-244 ?40 25 105 supply current (a) temperature (c) 0 700 600 500 400 300 200 100 129 1 1-245 93 devices sample count temperature delta (c) 0 2 4 6 18 14 16 12 10 8 ?1.2 ?1.0 ?0.8 ?0.6 ?0.4 ?0.2 0 0.2 0.4 0.6 0.8 1.0 129 1 1-246 sample count current (a) 0 5 10 15 35 30 25 20 9.60 9.65 9.70 9.75 9.80 9.85 9.90 9.95 10.00 10.05 10.10 129 1 1-247 ?5 5 ?4 ?3 ?2 ?1 0 1 2 3 4 100 80 60 40 20 0 input currrent (na) input voltage (v) ?40c, ain? ?40c, ain+ +25c, ain? +25c, ain+ +85c, ain? +85c, ain+ +105c, ain? +105c, ain+ 129 1 1-041
data sheet ad7175- 8 rev. 0 | page 17 of 64 noise performance and reso lution table 6 and table 7 show the rms noise, peak - to - peak noise, effective resolution , and the noise free (peak - to - peak) resolution of the ad7175 - 8 for various output data rates and filters. the numbers given are for the bipolar input range with an external 5 v reference. these numbers are typica l and are generated with a differential input voltage of 0 v when the adc is continu ously converting on a single channel. it is important to note that the peak - to - peak resolution is calculated based on the peak - to - peak noise. the peak - to - peak resolution r epresents the resolution for which there is no code flicker. table 6 . rms noise and peak -to - peak resolution vs. output data rate u sing a sinc5 + sinc1 filter (default) 1 output data rate (sps) rms noise (v rms) effective resolution (bits) peak - to - peak noise (v p - p) peak - to - peak resolution (bits) input buffers disabled 250,000 8.7 20.1 65 17.2 62,500 5.5 20.8 43 17.8 10,000 2.5 21.9 18.3 19.1 1000 0.77 23.6 5.2 20.9 59.92 0.19 24 1.1 23.1 49.96 0.18 24 0.95 23.3 16.66 0.1 24 0.45 24 5 0.07 24 0.34 24 input buffers enabled 250,000 9.8 20 85 16.8 62,500 6.4 20.6 55 17.5 10,000 3 21.7 23 18.7 1000 0.92 23.4 5.7 20.7 59.98 0.23 24 1.2 23.0 49.96 0.2 24 1 23.3 16.66 0.13 24 0.66 23.9 5 0.07 24 0.32 24 1 selected rates only, 1000 samples. table 7 . rms noise and peak -to - peak resolution vs. output data rate using a sinc3 filter 1 output data rate (sps) rms noise (v rms) effective resolution (bits) peak - to - peak noise (v p - p) peak - to - peak resolution (bits) input buffers disabled 250,000 210 15.5 1600 12.6 62,500 5.2 20.9 40 17.9 10,000 1.8 22.4 14 19.4 1000 0.56 24 3.9 21.3 60 0.13 24 0.8 23.6 50 0.13 24 0.7 23.8 16.66 0.07 24 0.37 24 5 0.05 24 0.21 24 input buffers enabled 250,000 210 15.5 1600 12.6 62,500 5.8 20.7 48 17.7 10,000 2.1 22.2 16 19.3 1000 0.71 23.7 4.5 21.1 60 0.17 24 1.1 23.1 50 0.15 24 0.83 23.5 16.66 0.12 24 0.6 24 5 0.08 24 0.35 24 1 selected rates only, 1000 samples.
ad7175- 8 data sheet rev. 0 | page 18 of 64 getting started the ad7175 - 8 offers the user a fast settling, high resolution, multiplexed adc with high levels of configurability. the ad7175 - 8 includes the following features: ? eight fully differential or 16 single - end ed analog inputs. ? a c rosspoint multiplexer selects any analog input combination as the input signals to be converted, routing it to the modulator positive or negative input. ? true rail - to - rail buffered analog and reference inputs. ? fully differential input o r single - ended input relative to any analog input. ? per channel configurability up to eight different setups can be defined. a separate setup can be mapped to each of the channels. each setup allows the user to configure whether the buffers are enabled or d isabled, gain and offset correction, filter type, output data rate, and reference source selection (internal/external). the ad7175 - 8 includes a precision 2.5 v low drift (2 ppm/c) band gap internal reference. this reference can used for the adc conversions, reducing the external component count. alternatively, the reference can be ou tput to the refout pin to be used as a low noise biasing voltage for external circuitry. an example of this is using the refout signal to set the input common mode for an external amplifier. the ad7175 - 8 includes two separate linear regulator blocks for both the analog and digital circuitry. the analog ldo regulates the av d d2 supply to 1.8 v, supplying the adc core. the user can tie the avdd1 and avdd2 supplies together for the easiest connection. if there is already a clean analog supply rail in the system in the range of 2 v (minimum) to 5.5 v (maximum), the user can also choose to connect this to the avdd2 input, allowing lower power dissipation. figure 41 . typical connection diagram dgnd AD7175-8 iovdd cs regcapd avss regcapa avdd2 avdd1 xtal1 39 40 1 37 36 3 2 12 13 14 15 16 17 20 21 22 9 10 7 8 6 8 5 3 1 nc tp tp trim 4 7 2 ref? ref+ 4.7f 0.1f 0.1f v out gnd nc v in 0.1f 4.7f v in 0.1f adr445 iovdd avdd2 0.1f avdd1 0.1f cx1 16mhz cx2 0.1f 1f 0.1f 1f optional external crystal circuitry capacitors clkin optional external clock input ain0/ref2? ain1/ref2+ ain14 ain15 ain16 see the buffered analog input section for further details xtal2/clkio dout/rdy din sclk cs dout/rdy din sclk 129 1 1-040
data sheet AD7175-8 rev. 0 | page 19 of 64 the linear regulator for the digital iovdd supply performs a similar function, regulating the input voltage applied at the iovdd pin to 1.8 v for the internal digital filtering. the serial interface signals always operate from the iovdd supply seen at the pin. this means that if 3.3 v is applied to the iovdd pin, the interface logic inputs and outputs operate at this level. the AD7175-8 can be used across a wide variety of applications, providing high resolution and accuracy. a sample of these scenarios is as follows: ? fast scanning of analog input channels using the internal multiplexer ? fast scanning of analog input channels using an external multiplexer with automatic control from the gpios. ? high resolution at lower speeds in either channel scanning or adc per channel applications ? high resolution applications requiring a highly integrated solution to save printed circuit board (pcb) area power supplies the AD7175-8 has three independent power supplies: avdd1, avdd2, and iovdd. avdd1 powers the crosspoint multiplexer and integrated analog and reference input buffers. avdd1 is referenced to avss, and avdd1 ? avs s = 5 v only. avdd1 ? avss can b e a sing l e 5 v supply or a 2.5 v split supply. the split supply operation allows true bipolar inputs. when using split supplies, consider the absolute maximum ratings (see the absolute maximum ratings section). avdd2 powers the internal 1.8 v analog ldo regulator. this regulator powers the adc core. avdd2 is referenced to avss, and avdd2 ? avss can range from 2 v (minimum) to 5.5 v (maximum). iovdd powers the internal 1.8 v digital ldo regulator. this regulator powers the digital logic of the adc. iovdd sets the voltage levels for the spi interface of the adc. iovdd is refer- enced to dgnd, and iovdd ? dgnd can vary from 2 v (minimum) to 5.5 v (maximum). there is no specific requirement for a power supply sequence on the AD7175-8. when all power supplies are stable, a device reset is required; see the AD7175-8 reset section for details on how to reset the device. digital communication the AD7175-8 has a 3- or 4-wire spi interface that is compatible with qspi?, microwire?, and dsps. the interface operates in spi mode 3 and can be operated with cs tied low. in spi mode 3, sclk idles high, the falling edge of sclk is the drive edge, and the rising edge of sclk is the sample edge. this means that data is clocked out on the falling/drive edge and data is clocked in on the rising/sample edge. figure 42. spi mode 3 sclk edges accessing the adc register map the communications register controls access to the full register map of the adc. this register is an 8-bit write only register. on power-up or after a reset, the digital interface defaults to a state where it is expecting a write to the communications register; therefore, all communication begins by writing to the communications register. the data written to the communications register determines which register is being accessed and if the next operation is a read or write. the register address bits (ra[5:0]) determine the specific register to which the read or write operation applies. when the read or write operation to the selected register is complete, the interface returns to its default state, where it expects a write operation to the communications register. figure 43 and figure 44 illustrate writing to and reading from a register by first writing the 8-bit command to the communications register, followed by the data for that register. figure 43. writing to a register (8-bit command with register address followed by data of 8, 16, or 24 bits; data length on din is dependent on the register selected) figure 44. reading from a register (8-bit command with register address followed by data of 8, 16, or 24 bits; data length on dout is dependent on the register selected) drive edge sample edge 12911-052 din sclk cs 8-bit command 8 bits, 16 bits, or 24 bits of data cmd data 12911-053 din sclk cs 8-bit command 8 bits, 16 bits, 24 bits, or 32 bits output cmd data dout/rdy 12911-054
ad7175- 8 data sheet rev. 0 | page 20 of 64 reading the id register is the r ecommended method for verifying correct communication with the device. the id register is a read only register and contains the value 0x3cdx for the ad7175 - 8 . the communications register and the id register details are described in table 8 and table 9 , respectively . ad7175 - 8 reset in situations where interface synchronization is lost, a write operation of at least 64 serial clock cycles with din high returns the adc to its default state by resetting the entire device , including the register contents. alternatively, if cs is being used with the digital interface, returning cs high sets the digital interface to its default sta te and halts any serial interface operation. configuration overvi ew after power - on or reset, the ad7175 - 8 default configuration are as follows . note that only a few of the register setting options are shown; this list is just an example. for full register information, see the register details section. ? channel configuration. ch0 is enabled, ain0 is selected as the positive input, and ain1 is selected as the negative input. setup 0 is selected. ? setup configuration. the internal refere nce and the analog input buffers are enabled. the reference input buffers are disabled. ? filter configuration. the sinc5 + sinc 1 filter is selected and the maximum output data rate is selected. ? adc mode. continuous conversion mode and the internal oscillat or are enabled. ? interface mode. crc and the data + status output are disabled. figure 45 shows an overview of the suggested flow for changing the adc configuration, divided into the following three blocks: ? channel configuration (see box a in figure 45) ? setup configuration (see box b in figure 45) ? adc mode and interface mode configuration (see box c in figure 45) channel configuration the ad7175 - 8 has 16 indep endent channels and 8 independent s etups. the user can select any of the analog input pairs on any channel, as well as any of the eight setups for any channel, giving the user full flexibility in the channel configuration. this also allows per channel conf iguration for up to eight channels when using differential inputs or single - ended inputs. channel configura - tion can be shared across multiple channels. channel registers the channel registers are used to select which of the 17 analog input pins (ain0 to ain 16 ) are used as either the positive analog input (ain+) or the negative analog input (ain?) for that channel. this register also contains a channel enable/disable bit and the setup selection bits, which are used to select from the eight available setups for this channel. when the ad7175 - 8 is operating with more tha n one channel enabled, the channel sequencer cycles through the enabled channels in sequential or der, from channel 0 to channel 15 . if a channel is disabled, it is skipped by the sequencer. details of the channel register for channel 0 are shown in table 10. figure 45 . suggested adc configuration flow table 8 . communications register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x00 comms [7:0] wen r/ w ra 0x00 w table 9 . id register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x07 id [15:8] id[15:8] 0x3cdx r [7:0] id[7:0] table 10 . channel 0 register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x10 ch0 [15:8] ch_en0 reserved setup_sel[2:0] reserved ainpos0[4:3] 0x8001 rw [7:0] ainpos0[2:0] ainneg0 adc mode and interface mode configuration select adc operating mode, clock source, enable crc, data + status, and more setup configuration 8 possible adc setups select filter order, output data rate, and more channel configuration select positive and negative input for each adc channel select one of 8 setups for adc channel a b c 12911-044
data sheet AD7175-8 rev. 0 | page 21 of 64 adc setups the AD7175-8 has eight independent setups. each setup consists of the following four registers: ? setup configuration register ? filter configuration register ? gain register ? offset register for example, setup 0 consists of setup configuration register 0, filter configuration register 0, gain register 0, and offset register 0. figure 46 shows the grouping of these registers. the setup is selectable from the channel registers (see the channel configuration section), which allows each channel to be assigned to one of eight separate setups. table 11 through table 14 show the four registers associated with setup 0. this structure is repeated for setup 1 to setup 3. setup configuration registers the setup configuration registers allow the user to select the output coding of the adc by selecting between bipolar mode and unipolar mode. in bipolar mode, the adc accepts negative differential input voltages, and the output coding is offset binary. in unipolar mode, the adc accepts only positive differential voltages, and the coding is straight binary. in either case, the input voltage must be within the avdd1/ avss supply voltages. the user can select the reference source using these registers. three options are available: an internal 2.5 v reference, an external reference connected between the ref+ and ref? pins, or avdd1 ? avss. the ana lo g input and refe rence input buffers can also be enabled or disabled using this register. filter configuration registers the filter configuration registers select which digital filter is used at the output of the adc modulator. the order of the filter and the output data rate is selected by setting the bits in this register. for more information, see the digital filters section. figure 46. adc setup register grouping table 11. setup configuration 0 register reg. name bits bit 7 bit 6 bit 5 bi t 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x20 setupcon0 [15:8] reserved bi_unipolar0 refbuf0 + refbuf0? ainbuf0+ ainbuf0? 0x1320 rw [7:0] burnout_en0 reserved ref_sel0 reserved table 12. filter configuration 0 register reg. name bits bit 7 bit 6 bit 5 bi t 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x28 filtcon0 [15:8] sinc3_map0 re served enhfilten0 enhfilt0 0x0500 rw [7:0] reserved order0 odr0 table 13. gain configuration 0 register reg. name bits bit[23:0] reset rw 0x38 gain0 [23:0] gain0[23:0] 0x5xxxx0 rw table 14. offset configuration 0 register reg. name bits bit[23:0] reset rw 0x30 offset0 [23:0] o ffset0[23:0] 0x800000 rw setup config registers filter confi g registers offset registers gain registers* select peripheral functions for adc channel select digital filter type and output data rate input buffers reference buffers burnout reference source sinc5 + sinc1 sinc3 sinc3 map enhanced 50hz and 60hz gain correction optionally programmed per setup as required (*factory calibrated) offset correction optionally programmed per setup as required 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 setupcon3 setupcon5 setupcon6 setupcon7 setupcon4 setupcon0 setupcon2 setupcon1 filtcon3 filtcon5 filtcon6 filtcon7 filtcon4 filtcon0 filtcon2 filtcon1 gain3 gain5 gain6 gain7 gain4 gain0 gain2 gain1 offset3 offset5 offset6 offset7 offset4 offset0 offset2 offset1 12911-045
ad7175- 8 data sheet rev. 0 | page 22 of 64 gain registers the gain register s are 24 - bit register s that hold the gain calibration coefficient for the adc. the gain registers are read/write registers. these registers are configured at power - on with factory calibrated coefficients. therefore, every device has different default coefficients. the default value is automatically overwritten if a system full - scale calibration is initiated by the user or if the gain register is written to by the user. for more information on calibration, see the operating modes section. offset registers the offset register s hold the offset calibration coefficient for the adc. the power - on reset value of the offset register s is 0x800000. the offset register s are 24 - bit read/write register s . the power - on reset value is automatically overwritten if an internal or system zero - scale calibration is initiated by the user or if the offset register s are written to by the user. adc mode and interface mode configuration the adc mode register and the interface mode register configure the core peripherals for use by the ad7175 - 8 and the mode for the digital interface. adc mode register the adc mode register primarily set s the conversion mode of the adc to either continuous or single conversion. the user can also select the standby and power - down modes, as well as any of the calibration modes. in addition, this register contains the clock source select bits and the internal reference enable bits. the reference select bits are contained in the setup configuration registers (see the adc setups section for more information). interface mode register th e interface mode register configures the digital interface operation. this register allows the user to control data - word length, crc enable, data + status read, and continuous read mode. the details of the adc mode and interface mode registers are shown in table 15 and table 16 , respectively . for more information, see the digital interface section. table 15 . adc mode register reg. nam e bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x01 adcmode [15:8] ref_en hide_delay sing_cyc reserved delay 0x a 000 rw [7:0] reserved mode clocksel reserved table 16 . interface mode register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x02 ifmode [15:8] reserved alt_sync iostrength reserved dout_reset 0x0000 rw [7:0] contread data_stat reg_check reserved crc_en reserved wl16
data sheet AD7175-8 rev. 0 | page 23 of 64 understanding configuration flexibility the most straightforward implementation of the AD7175-8 is to use eight differential inputs with adjacent analog inputs and run all of them with the same setup, gain correction, and offset correction register. in this case, the user selects the following differential inputs: ain0/ain1, ain2/ain3, ain4/ain5, ain6/ain7, ain8/ain9, ain10/ain11, ain12/ain13, and ain14/ain15. in figure 47, the registers shown in black font must be programmed for such a configuration. the registers shown in gray font are redundant in this configuration. programming the gain and offset registers is optional for any use case, as indicated by the dashed lines between the register blocks. an alternative way to implement these eight fully differential inputs is by taking advantage of the eight available setups. motivation for doing this includes having a different speed/noise requirement on some of the eight differential inputs vs. other inputs, or there may be a specific offset or gain correction for particular channels. figure 48 shows how each of the differential inputs may use a separate setup, allowing full flexibility in the configuration of each channel. figure 47. eight full y differential inputs, all usin g a single setup (setupcon0; filtcon0; gain0; offset0) figure 48. eight fully differential inputs with a setup per channel setup config registers channel registers filter config registers offset registers gain registers* select peripheral functions for adc channel select analog input pairs enable the channel select setup 0 select digital filter type and output data rate input buffers reference buffers burnout reference source 250ksps to 5sps sinc5 + sinc1 sinc3 sinc3 map enhanced 50hz and 60hz gain correction optionally programmed per setup as required (*factory calibrated) offset correction optionally programmed per setup as required 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 setupcon3 setupcon5 setupcon6 setupcon7 setupcon4 setupcon0 setupcon2 setupcon1 filtcon3 filtcon5 filtcon6 filtcon7 filtcon4 filtcon0 filtcon2 filtcon1 gain3 gain5 gain6 gain7 gain4 gain0 gain2 gain1 offset3 offset5 offset6 offset7 offset4 offset0 offset2 offset1 0x10 ch0 0x11 ch1 0x12 ch2 0x13 ch3 0x14 ch4 0x15 ch5 0x16 ch6 0x17 ch7 0x18 ch8 0x19 ch9 0x1a ch10 0x1b ch11 0x1c ch12 0x1d ch13 0x1e ch14 0x1f ch15 ain0 ain1 ain2 ain3 ain4 ain5 ain6 ain7 ain8 ain9 ain10 ain11 ain12 ain13 ain14 ain15 ain16 12911-046 setup config registers filter config registers offset registers gain registers* select peripheral functions for adc channel select analog input pairs enable the channel select setup select digital filter type and output data rate input buffers reference buffers burnout reference source 250ksps to 5sps sinc5 + sinc1 sinc3 sinc3 map enhanced 50hz and 60hz gain correction optionally programmed per setup as required (*factory calibrated) offset correction optionally programmed per setup as required 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 setupcon3 setupcon5 setupcon6 setupcon7 setupcon4 setupcon0 setupcon2 setupcon1 filtcon3 filtcon5 filtcon6 filtcon7 filtcon4 filtcon0 filtcon2 filtcon1 gain3 gain5 gain6 gain7 gain4 gain0 gain2 gain1 offset3 offset5 offset6 offset7 offset4 offset0 offset2 offset1 0x10 ch0 0x11 ch1 0x12 ch2 0x13 ch3 0x14 ch4 0x15 ch5 0x16 ch6 0x17 ch7 ch8 ch9 ch10 ch11 ch12 ch13 ch14 ch15 ain0 ain1 ain2 ain3 ain4 ain5 ain6 ain7 ain8 ain9 ain10 ain11 ain12 ain13 ain14 ain15 ain16 channel registers 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f 12911-047
AD7175-8 data sheet rev. 0 | page 24 of 64 figure 49 shows an example of how the channel registers span between the analog input pins and the setup configurations downstream. in this random example, seven differential inputs and two single-ended inputs are required. the single-ended inputs are the ain8/ain16 and ain15/ain16 combinations. the first five differential input pairs (ain0/ain1, ain2/ain3, ain4/ain5, ain6/ain7, and ain9/ain10) use the same setup: setupcon0. the two single-e nded input pairs (ain8/ain16 and ain15/ ain16) are set up as a diagnostics; therefore, use a separate setup: setupcon1. the final two differential inputs (ain11/ain12 and ain13/ain14) also use a separate setup: setupcon2. given that three setups are selected for use, the setupcon0, setupcon1, and setupcon2 registers are programmed as required, and the filtcon0, filtcon1, and filtcon2 registers are also programmed as required. optional gain and offset correction can be employed on a per setup basis by programming the gain0, gain1, and gain2 registers and the offset0, offset1, and offset2 registers. in the example shown in figure 49, the ch0 to ch8 registers are used. setting the msb in each of these registers, the ch_en0 to ch_en8 bits, enables the nine combinations via the crosspoint multiplexer. when the AD7175-8 converts, the sequencer transitions in ascending sequential order from ch0 to ch1 to ch2, and then on to ch8 before looping back to ch0 to repeat the sequence. figure 49. mixed differential and single-ended configuration using multiple shared setups setup config registers filter config registers offset registers gain registers* select peripheral functions for adc channel select analog input pairs enable the channel select setup select digital filter type and output data rate input buffers reference buffers burnout reference source 250ksps to 5sps sinc5 + sinc1 sinc3 sinc3 map enhanced 50hz and 60hz gain correction optionally programmed per setup as required (*factory calibrated) offset correction optionally programmed per setup as required 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 setupcon3 setupcon5 setupcon6 setupcon7 setupcon4 setupcon0 setupcon2 setupcon1 filtcon3 filtcon5 filtcon6 filtcon7 filtcon4 filtcon0 filtcon2 filtcon1 gain3 gain5 gain6 gain7 gain4 gain0 gain2 gain1 offset3 offset5 offset6 offset7 offset4 offset0 offset2 offset1 0x10 ch0 0x11 ch1 0x12 ch2 0x13 ch3 0x14 ch4 0x15 ch5 0x16 ch6 0x17 ch7 ch8 ch9 ch10 ch11 ch12 ch13 ch14 ch15 ain0 ain1 ain2 ain3 ain4 ain5 ain6 ain7 ain8 ain9 ain10 ain11 ain12 ain13 ain14 ain15 ain16 channel registers 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f 12911-048
data sheet ad7175- 8 rev. 0 | page 25 of 64 circuit description buffered analog inpu t the ad7175 - 8 has true rail - to - r ail, integrated, precision unity - gain buffers on both adc analog inputs. the buffers provide the benefit of giving the user high input impedance with only 30 na typical input current, allowing high impedance sources to be connected directly to the analog inputs. the buffers fully drive the internal adc switch capacitor sampling network, simplifying the analog front - end circuit requirements while consuming a very efficient 2.9 ma typical per buffer. each analo g input buffer amplifier is fully chopped, meani ng that it minimizes the offset error drift and 1/f noise of the buffer. the 1/f noise profile of the adc and buffer combined is shown in figure 50. figure 50 . shorted input fft (analog input buffers enabled) the analog input buffers do not suffer from linearity degradation when operating at the rails, unlike many discrete amplifiers. when operating at or close to the avdd1 and avss supply rails, there is an increase in input current. this increase is most notable at higher temperatures. figure 40 show s the analog input curr ent for various conditions. with the analog input buffers disabled, the average input current to the ad7175 - 8 changes linearly with the differential input voltage at a rate of 48 a / v. crosspoint multiplex er there are 17 analog input pins: ain0 to ain 16 . each of these pins connects to the internal crosspoint multiplexer. the crosspoint multiplexer enables any of these inputs to be configured as an input pair, either single - ended or fully differential. the ad7175 - 8 can have up to 16 active channels. when more than one channel is enabled, the channels are automatically sequenced in order from the lowest enabled channel number to the highest enabled channel n umber. the output of the multiplexer is connected to the input of the integrated true rail - to - rail buffers. these can be bypassed and the multiplexer output can be directly connected to the switched - capacitor input of the adc. the simplified analog input c ircuit is shown in figure 51. figure 51 . simplified analog input circuit the cs1 and cs2 capacitors each have a magnitude in the order of a number of picofarads. this capacitance is the combination of both the sampling capacitance and the parasitic capacitance. fully differential inputs because the ain0 to ain16 analog inputs are connected to a crosspoint multiplexer, any com bination of signals can be used to create an analog input pair. this crosspoint multiplexer allows the user to select eight fully differential inputs or 16 single - ended inputs. if eight fully differential input paths are connected to the ad7175 - 8 , using adjacent analog input pins such as ain0/ain1 for the differential input pair is recommended. this is due to the relative locations of these pins to each other. decouple a ll analog inputs to avss. single - ended inputs the user can also choose to measure 16 different single - ended analog inputs. in this case, each of the analog inputs is converted as the difference between the single - ended input to be measured and a set analog input common pin. because there is a crosspoint multiplexer, the user can set any of the analog inputs as the common pin. an exam ple of such a scenario is to connect the ain8 pin to avss or to the refout voltage (that is, avss + 2.5 v) and select this input when configuring the crosspoint multiplexer. when using the ad7175 - 8 with single - ended inputs . ?250 ?200 ?150 ?100 ?50 0 0.1 1 10 100 1k 10k amplitude (db) frequency (hz) 129 1 1-259 ain0 ain1 avdd1 avss avss avss avdd1 avss ain14 avdd1 ain16 avdd1 ain15 avdd1 avss ?1 cs1 cs2 +in ?in ?2 ?2 ?1 129 1 1-050
ad7175- 8 data sheet rev. 0 | page 26 of 64 ad7175 - 8 reference the ad7175 - 8 offers the user the option of either supplying an external reference to the ref+ and ref? or ref2+ and ref2 - pins of the device or allowing the use of the internal 2.5 v, low noise, low drift reference. select the reference source to be us ed by the analog input by setting the ref_selx bits (bits[5:4]) in the setup configuration registers appropriately. the structure of the setup configuration 0 register is shown in table 17 . the ad7175 - 8 defaults on power - up to use the internal 2.5 v reference. external reference the ad7175 - 8 has a fully differential reference input applied through the ref+ and ref? or ref2+ and ref2 pins. standard low noise, low drift voltage references, such as the adr445 , adr444 , and adr441 , are recommended for use. apply the external reference to the ad7175 - 8 reference pins as shown in figure 52 . decouple the output of any external reference to avss. as shown in figure 52 , the adr445 output is decoupled with a 0.1 f capacitor at its output for stability purposes. the output is then connected to a 4.7 f capacitor, which acts as a reservoir for any dynamic charge required by the adc, and followed by a 0.1 f decoupling capacitor at the ref+ or ref2+ input. this capacitor is placed as close as possible to the ref+/ref2+ and ref?/ref2 ? pins. the ref?/ref2 ? pin is connected directly to the avss potential. on power - up of the ad7175 - 8 , the internal reference is enabled by default and is output on the refout pin. when an external reference is used instead of the internal reference to supply the ad7175 - 8 , attention must be paid to the output of the refout pin. if the internal reference is not being used elsewhere in the application, ensure that the refout pin is not hardwired to avss because this draws a large current on power - up. on power - up, if the internal reference is not being used , write to the adc mode register, disabling the internal reference. this is controlled by the ref_en bit (bit 15) in the adc mode register, which is shown in table 18. internal reference the ad7175 - 8 includes its own low noise, low drift voltage reference. the internal reference has a 2.5 v output. the internal reference is output on the refout pin after the ref_en bit in the adc mode register is set and is decoupled to avss with a 0.1 f capacitor. the ad7175 - 8 internal reference is enabled by default on power - up and is selected as the reference source for the adc. when using the internal reference, the inl performance degrade s as shown in figure 23. the refout signal is buffered before being output to the p in. the signal can be used externally in the circuit as a common - mode source for external amplifier configurations. figure 52 . external reference adr445 connected to the ad7175 - 8 reference pins table 17 . setup configuration 0 register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x20 setupcon0 [15:8] reserved bi_unipolar0 refbuf0+ refbuf0? ainbuf0+ ainbuf0? 0x1320 rw [7:0] burnout_en0 reserved ref_sel0 reserved table 18 . adc mode register reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x01 adcmode [15:8] ref_en hide_delay sing_cyc reserved delay 0x a 000 rw [7:0] r eserved mode clocksel reserved 39 40 ref? ref+ 4.7f 0.1f 1 1 1 1 1 0.1f 0.1f 5.5v to 18v adr445 2 5v vref AD7175-8 129 1 1-159 1 all decoupling is to avss. 2 any of the adrf440/adr441/adr443/adr444/adr445 family of references can be used. the adr444 and adr441 both enable reuse of the 5v analog supply needed for avdd1 to power the reference v in .
data sheet ad7175- 8 rev. 0 | page 27 of 64 buffered reference i nput the ad7175 - 8 has true rail - to - rail, integrated, precision unity gain buffers on both adc reference inputs. the buffers provide the ben efit of giving the user high input impedance and allow high impedance external sources to be directly connected to the reference inputs. the integrated reference buffers can fully drive the internal reference switch capacitor sampling network, simplifying the reference circuit requirements while consuming a very efficient 2.9 ma typical per buffer. each reference input buffer amplifier is fully chopped, meaning that it minimizes the offset error drift and 1/f noise of the buffer. when using an external refe rence, such as the adr445 , adr444 , and adr441 , these buffers are not r equired because these references, with proper decoupling, can drive the reference inputs directly. clock source the ad7175 - 8 uses a nominal master clock of 16 mhz. the ad7175 - 8 source s its sampling clock from one of three sources: ? internal oscillator ? external crystal ? external clock source all output data rates listed in the data sheet relate to a master clock rate of 16 mhz. using a lower clock frequency from, for instance, an external source scales any listed data rate proportion - ally. to achieve the specified data rates, particularly rates for the rejection of 50 hz and 60 hz, use a 16 mhz clock. the source of the master clock is selected by setting the clocksel bits (bits[3:2]) in the adc mode register as shown in table 18 . the default operation on power - up and reset of the ad7175 - 8 is to operate with the internal oscillator. it is possible to fine tune the output data rate and filter notch at low output data rates using the sinc3_mapx bit. see the sinc3 filter section for more information. internal oscillator the internal oscillator runs at 16 mhz and can be used as the adc master clock. it is the default clock source for the ad7175 - 8 and is specified with an accuracy of 2.5%. there is an option to allow the internal clock oscillator to be output on the xtal 2/clkio pin. the clock output is driven to the iovdd logic level. use of this option can affect the dc performance of the ad7175 - 8 due to the disturbance intro - duced by the output driver. the extent to which the performance is affected depends on the iovdd voltage supply. higher iovdd voltages create a wider logic output swing from the driver and affect performance to a greater extent. this effect is further exaggerated if the iostrength bit is set at higher iovdd levels (see table 28 for more information). external crystal if higher precision, lower jitter clock sources are required, the ad7175 - 8 can use an external crystal to generate the master clock. the crystal is connected to the xtal1 and xtal2/clkio pins. a recommended crystal for use is the fa - 20h a 16 mhz, 10 ppm, 9 pf crystal from epson - toyocom which i s available in a surface - mount package. as shown in figure 53 , insert two capacitors from the traces connecting the crystal to the xtal1 and xtal2/clki o pins. these capacitors allow for circuit tuning. connect these capacitors to the dgnd pin. the value for these capacitors depends on the length and capacitance of the trace connections between the crystal and the xtal1 and xtal2/clkio pins. therefore, th e values of these capacitors differ depending on the pcb layout and the crystal employed. figure 53 . external crystal connections the external crystal circuitry can be sensitive to the sclk edges, depending on sclk frequency, iovdd voltage, crystal circuitry layout, and the crystal used. during crystal startup, any disturbances caused by the slck edges may cause double edges on the c rystal input, resulting in invalid conversions until the crystal voltage has reached a high enough level such that any interference from the sclk edges is insufficient to cause double clocking. this double clocking can be avoided by ensuring that the cryst al circuitry has reached a sufficient voltage level after startup before applying any sclk signal . due to the nature of the crystal circuitry, it is recommended that empirical testing of the circuit b e performed under the required conditions, with the fina l pcb layout and crystal, to ensure correct operation. external clock the ad7175 - 8 can also use an externally supplied clock. in systems where this is desirable, the external clock is routed to the xtal2/clkio pin. in this configuration, the xtal2/clkio pin accepts the externally sourced clock and routes it to the modulator. the logic level of this clock input is defined by the voltage applied to the iovdd pin. 12 13 cx1 cx2 xtal1 xtal2/clkio *decouple to dgnd. AD7175-8 * * 129 1 1-160
ad7175- 8 data sheet rev. 0 | page 28 of 64 digital filters the ad7175 - 8 has three flexible filter options to allow optimization of nois e, settling time, and rejection. ? sinc5 + sinc1 filter ? sinc3 filter ? enhanced 50 hz and 60 hz rejection filte rs figure 54 . digital filter block diagram the filter and output data rate are configured by setting the appropriate bits in the filter configuration register for the selected setup. each channel can use a different setup and the refore, a different filter and output data rate. see the register details section for more information. sinc5 + sinc1 filter the sinc5 + sinc1 filter i s targeted at multiplexed applications and achieves single cycle settling at output data rates of 10 ksps and lower. the sinc5 block output is fixed at the maximum rate of 250 ksps, and the sinc1 block output data rate can be varied to control the final adc output data rate. figure 55 shows the frequency domain response of the sinc5 + sinc1 filter at a 50 sps odr . the sinc5 + sinc 1 filter has a slow roll - off over frequency and narrow notches. figure 55 . sinc5 + sinc1 filter response at 50 sps odr the odrs with the accompanying settling time and rms noise for the sinc5 + sinc1 filter are shown in table 19 and table 20. sinc3 filter the sinc3 filter achieves the best single - channel noise performance at lower rates and is, therefore, most suitable for single - channel applications. the sinc3 filter always has a settling time , t settle , equal to t settle = 3/ output data rate figure 56 shows the frequency domain filter response for the sinc3 filter. the sinc3 filter has good roll - off over frequency and has wide notches for g ood notch frequency rejection. figure 56 . sinc3 filter response the odrs with the accompanying settling time and rms noise for the sinc3 filter are shown in table 21 and table 22 . it is possible to finely tune the output data rate for the sinc3 filter by setting the sinc3_m apx bit s in the filter configuration registers. if this bit is set, the mapping of the filter register changes to directly program the decimation rate of the sinc3 filter. all other options are eliminated. the data rate when on a single channel can be calculated using the following equation: 4:0] filtconx[1 f rate data output mod = 32 where: f mod is the modulator rate (mclk/ 2 ) and is 8 mhz for a 16 mhz mclk. filtconx[14:0] are the contents on the filter configu ration registers excluding the msb. for example, an output data rate of 50 sps can be achieved with sinc3_mapx enabled by setting the filtconx[14:0] bits to a value of 5000. sinc1 sinc5 sinc3 50hz and 60hz postfilter 129 1 1-058 0 ?120 0 150 100 50 filter gain (db) frequency (hz) ?100 ?80 ?60 ?40 ?20 129 1 1-059 0 ?120 0 15 0 10 0 5 0 f i lter g a i n (d b ) f r eq u enc y (h z) ?100 ?80 ?60 ?40 ?20 ?110 ?90 ?70 ?50 ?30 ?10 129 1 1-060
data sheet ad7175- 8 rev. 0 | page 29 of 64 single cycle settlin g by default, the ad7175 - 8 is configured with the sing_cyc bit in the adc mode register set so that only fully settled data is output, ef fectively putting the adc into a single cycle settling mode. this mode achieves single cycle settling by reducing the output data rate to be equal to the settling time of the adc for the selected output data rate. this bit has no effect with the sinc5 + si nc1 filter at output data rates of 10 ksps and lower. figure 57 shows a step on the analog input with this mode disabled and the sinc3 filter selected. the analog input requires at least three cycles after the step change for the output to reach the final settled value. figure 57 . step input without single cycle settling figure 58 shows the same step on the analog input but with single cycle settling enabled. the analog input requires at least a single cycle for the output to be fully settled. the output data rate, as indicated by the rdy signal, is now reduced to equal the settling time of the filter at the selected output data rate. figure 58 . step input with single cycle settling table 19 . output data rate, settling time, and noise using the sinc5 + sinc1 filter with input buffers disabled default output data rate (sps/channel); sing_cyc = 1 or with multiple channels enabled 1 output data rate (sps); sing_cyc = 0 and single channel enabled 1 settling time 1 notch frequency (hz) noise (v rms) effective resolution with 5 v reference (bits) noise (v p - p) 2 peak - to - peak resolution with 5 v reference (bits) 50,000 250,000 20 s 250,000 8.7 20.1 65 17.2 41,667 125,000 24 s 125,000 7.2 20.4 60 17.3 31,250 62,500 32 s 62,500 5.5 20.8 43 17.8 27,778 50,000 36 s 50,000 5 20.9 41 17.9 20,833 31,250 48 s 31,250 4 21.3 32 18.3 17,857 25,000 56 s 25,000 3.6 21.4 29 18.4 12,500 15,625 80 s 15,625 2.9 21.7 22 18.8 10,000 10,000 100 s 11,905 2.5 21.9 18.3 19.1 5000 5000 200 s 5435 1.7 22.5 12 19.7 2500 2500 400 s 2604 1.2 23.0 8.2 20.2 1000 1000 1.0 ms 1016 0.77 23.6 5.2 20.9 500.0 500 2.0 ms 504 0.57 24 3.2 21.6 397.5 397.5 2.516 ms 400.00 0.5 24 3 21.7 200.0 200 5.0 ms 200.64 0.36 24 2 22.3 100 100 10 ms 100.16 0.25 24 1.3 22.9 59.92 59.92 16.67 ms 59.98 0.19 24 1.1 23.1 49.96 49.96 20.016 ms 50.00 0.18 24 0.95 23.3 20.00 20 50.0 ms 20.01 0.11 24 0.6 24 16.66 16.66 60.02 ms 16.66 0.1 24 0.45 24 10.00 10 100 ms 10.00 0.08 24 0.4 24 5.00 5 200 ms 5.00 0.07 24 0.34 24 1 the settling time is rounded to the nearest microsecond. this is reflected in the output data rate and channel switching rate. channel swit ching rate = 1 settling time. 2 measurement taken using 1000 samples . 1/odr analog input fully settled adc output 129 1 1-061 t settle analog input fully settled adc output 129 1 1-062
ad7175- 8 data sheet rev. 0 | page 30 of 64 table 20 . output data rate, settling time, and noise using the sinc5 + sinc1 filter with input buffers enabled default output data rate (sps/channel); sing_cyc = 1 or with multiple channels enabled 1 output data rate (sps); sing_cyc = 0 and single channel enabled 1 settling time 1 notch frequency (hz) noise (v rms) effective resolution with 5 v reference (bits) noise (v p - p) 2 peak - to - peak resolution with 5 v reference (bits) 50,000 250,000 20 s 250,000 9.8 20 85 16.8 41,667 125,000 24 s 125,000 8.4 20.2 66 17.2 31,250 62,500 32 s 62,500 6.4 20.6 55 17.5 27,778 50,000 36 s 50,000 5.9 20.7 49 17.6 20,833 31,250 48 s 31,250 4.8 21 39 18.0 17,857 25,000 56 s 25,000 4.3 21.1 33 18.2 12,500 15,625 80 s 15,625 3.4 21.5 26 18.6 10,000 10,000 100 s 11,905 3 21.7 23 18.7 5000 5000 200 s 5435 2.1 22.2 16 19.3 2500 2500 400 s 2604 1.5 22.7 10 19.9 1000 1000 1.0 ms 1016 0.92 23.4 5.7 20.7 500.0 500 2.0 ms 504 0.68 23.8 3.9 21.3 397.5 397.5 2.516 ms 400.00 0.6 24 3.7 21.4 200.0 200 5.0 ms 200.64 0.43 24 2.2 22.1 100 100 10 ms 100.16 0.32 24 1.7 22.5 59.92 59.92 16.67 ms 59.98 0.23 24 1.2 23 49.96 49.96 20.016 ms 50.00 0.2 24 1 23.3 20.00 20 50.0 ms 20.01 0.14 24 0.75 23.7 16.66 16.66 60.02 ms 16.66 0.13 24 0.66 23.9 10.00 10 100 ms 10.00 0.1 24 0.47 24 5.00 5 200 ms 5.00 0.07 24 0.32 24 1 the settling time is rounded to the nearest microsecond. this i s reflected in the output data rate and channel switching rate. channel swit ching rate = 1 settling time. 2 measurement taken using 1000 samples .
data sheet AD7175-8 rev. 0 | page 31 of 64 table 21. output data rate, settling time, and noise using the sinc3 filter with input buffers disabled default output data rate (sps/channel); sing_cyc = 1 or with multiple channels enabled 1 output data rate (sps); sing_cyc = 0 and single channel enabled 1 settling time 1 notch frequency (hz) noise (v rms) effective resolution with 5 v reference (bits) noise (v p-p) 2 peak-to-peak resolution with 5 v reference (bits) 83,333 250,000 12 s 250,000 210 15.5 1600 12.6 41,667 125,000 24 s 125,000 28 18.4 200 15.6 20,833 62,500 48 s 62, 500 5.2 20.9 40 17.9 16,667 50,000 60 s 50, 000 4.2 21.2 34 18.2 10,417 31,250 96 s 31, 250 3.2 21.6 26 18.6 8333 25,000 120 s 25,000 2.9 21.7 23 18.7 5208 15,625 192 s 15,625 2.2 22.1 17 19.2 3333 10,000 300 s 10,000 1.8 22.4 14 19.4 1667 5000 6 s 5000 1.3 22.9 9.5 20 833 2500 1.2 ms 2500 0.91 23.4 6 20.7 333.3 1000 3 ms 1000 0.56 24 3.9 21.3 166.7 500 6 ms 500 0.44 24 2.5 21.9 133.3 400 7.5 ms 400 0.4 24 2.3 22.1 66.7 200 15 ms 200 0.25 24 1.4 22.8 33.33 100 30 ms 100 0.2 24 1 23.3 19.99 60 50.02 ms 59.98 0.13 24 0.8 23.6 16.67 50 60 ms 50 0.13 24 0.7 23.8 6.67 20 150 ms 20 0.08 24 0.42 24 5.56 16.67 180 ms 16.67 0.07 24 0.37 24 3.33 10 300 ms 10 0.06 24 0.28 24 1.67 5 600 ms 5 0.05 24 0.21 24 1 the settling time is rounded to the nearest microsecond. this is reflected in the output data rate and channel switching rate. channel switching rate = 1 settling time. 2 measurement taken using 1000 samples.
ad7175- 8 data sheet rev. 0 | page 32 of 64 table 22 . output data rate, settling time, and noise using the sinc3 filter with input buffers enabled default output data rate (sps/channel); sing_cyc = 1 or with multiple channels enabled 1 output data rate (sps); sing_cyc = 0 and single channel enabled 1 settling time 1 notch frequency (hz) noise (v rms) effective resolution with 5 v reference (bits) noise (v p - p) 2 peak - to - peak resolution with 5 v reference (bits) 83,333 250,000 12 s 250,000 210 15.5 1600 12.6 41,667 125,000 24 s 125,000 28 18.4 210 15.5 20,833 62,500 48 s 62,500 5.8 20.7 48 17.7 16,667 50,000 60 s 50,000 4.9 21 41 17.9 10,417 31,250 96 s 31,250 3.8 21.3 30 18.3 8333 25,000 120 s 25,000 3.4 21.5 26 18.6 5208 15,625 192 s 15,625 2.6 21.9 18 19.1 3333 10,000 300 s 10,000 2.1 22.2 16 19.3 1667 5000 6 s 5000 1.5 22.7 11 19.8 833 2500 1.2 ms 2500 1.1 23.1 7 20.4 333.3 1000 3 ms 1000 0.71 23.7 4.5 21.1 166.7 500 6 ms 500 0.52 24 3 21.7 133.3 400 7.5 ms 400 0.41 24 2.7 21.8 66.7 200 15 ms 200 0.32 24 1.8 22.4 33.33 100 30 ms 100 0.2 24 1.2 23 19.99 60 50.02ms 59.98 0.17 24 1.1 23.1 16.67 50 60 ms 50 0.15 24 0.83 23.5 6.67 20 150 ms 20 0.13 24 0.61 24 5.56 16.67 180 ms 16.67 0.12 24 0.6 24 3.33 10 300 ms 10 0.1 24 0.55 24 1.67 5 600 ms 5 0.08 24 0.35 24 1 the settling time is rounded to the nearest microsecond. this is reflected in the output data rate and channel switching rate. channel switch ing rate = 1 settling time. 2 measurement taken using 1000 samples .
data sheet AD7175-8 rev. 0 | page 33 of 64 enhanced 50 hz and 60 hz rejection filters the enhanced filters are designed to provide rejection of 50 hz and 60 hz simultaneously and to allow the user to trade off settling time and rejection. these filters can operate at up to 27.27 sps or can reject up to 90 db of 50 hz 1 hz and 60 hz 1 hz interference. these filters are realized by postfiltering the output of the sinc5 + sinc1 filter. for this reason, the sinc5 + sinc1 filter must be selected when using the enhanced filters to achieve the specified settling time and noise performance. table 23 shows the output data rates with the accompanying settling time, rejection, and rms noise. figure 59 to figure 66 show the frequency domain plots of the responses from the enhanced filters. table 23. enhanced filters output da ta rate, noise, settling time, and re jection using the enhanced filters output data rate (sps) settling time (ms) simultaneous rejection of 50 hz 1 hz and 60 hz 1 hz (db) 1 noise (v rms) peak-to-peak resolution (bits) comments input buffers disabled 27.27 36.67 47 0.22 22.7 see figure 59 and figure 62 25 40.0 62 0.2 22.9 see figure 60 and figure 63 20 50.0 85 0.2 22.9 see figure 61 and figure 64 16.667 60.0 90 0.17 23 see figure 65 and figure 66 input buffers enabled 27.27 36.67 47 0.22 22.7 see figure 59 and figure 62 25 40.0 62 0.22 22.7 see figure 60 and figure 63 20 50.0 85 0.21 22.8 see figure 61 and figure 64 16.667 60.0 90 0.21 22.8 see figure 65 and figure 66 1 master clock = 16 mhz.
AD7175-8 data sheet rev. 0 | page 34 of 64 figure 59. 27.27 sps odr, 36.67 ms settling time figure 60. 25 sps odr, 40 ms settling time figure 61. 20 sps odr, 50 ms settling time figure 62. 27.27 sps odr, 36.67 ms settling time at 50 hz/60 hz figure 63. 25 sps odr, 40 ms settling time at 50 hz/60 hz figure 64. 20 sps odr, 50 ms settling time at 50 hz/60 hz 0 ?100 0600 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 100 200 300 400 500 12911-063 0 ?100 0 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 600 100 200 300 400 500 12911-065 0 ?100 06 0 0 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 100 200 300 400 500 12468-067 0 ?100 40 70 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 45 50 55 60 65 12911-064 0 ?100 40 70 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 45 50 55 60 65 12911-066 0 ?100 40 70 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 45 50 55 60 65 12911-068
data sheet ad7175- 8 rev. 0 | page 35 of 64 figure 65 . 16.667 sps odr, 60 ms settling time figure 66 . 16.667 sps odr, 60 ms settling time at 50 hz/60 hz 0 ?100 0 600 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 100 200 300 400 500 129 1 1-069 0 ?100 40 70 filter gain (db) frequency (hz) ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 45 50 55 60 65 129 1 1-070
ad7175- 8 data sheet rev. 0 | page 36 of 64 operating modes the ad7175 - 8 has a number of operating modes that can be set from the adc mode re gister and interface mode register (see table 27 and table 28 ). these modes are as follows and are described in the following sections : ? continuous conversion mode ? continuous read mode ? single conversion mode ? standby mode ? power - down mode ? calibration modes (three modes ) continuous conversio n mode continuous conversion is the default power - up mode. the ad7175 - 8 converts continu ously, and the rdy bit in the status register goes low each time a conversion is complete. if cs is low, the rdy output also goes low when a conversion is complete. to read a conversion, the user writes to the communications register, indicating that the next operation is a read of the data register. when the data - word has been read from the data register, the dout/ rdy pin goes high. the user c an read this register additional times, if required. however, the user must ensure that the data register is not being accessed at the completion of the next conversion; otherwise, the new conversion word is lost. when several channels are enabled, the adc automatically sequences through the enabled channels, performing one conversion on each channel. when all channels have been converted, the sequence starts again with the first channel. the channels are converted in order from lowest enabled channel to hi ghest enabled channel. the data register is updated as soon as each conversion is available. the rdy output pulses low each time a conversion is available. the user can then read the c onversion while the adc converts the next enabled channel . if the data_stat bit in the interface mode register is set to 1, the contents of the status register, along with the conversion data, are output each time the data register is read. the status register indicates the channel to which the conversio n corresponds. figure 67 . continuous conversion mode din sclk dout/rdy cs 0x44 0x44 data data 129 1 1-071
data sheet ad7175- 8 rev. 0 | page 37 of 64 continuous read mode in continuous read mode, it is not required to write to the communications register before r eading adc data; apply o nly the required number of sclk pulses after rdy goes low to indicate the end of a conversion. when the conversion is read, rdy returns high until the next conversion is available. in th is mode, the data can be read only once. the user must also ensure that the data - word is read before the next conversion is complete. if the user has not read the conversion before the completion of the next conversion or if insufficient serial clocks are applied to the ad7175 - 8 to read the data - word, the serial output register is rese t shortly before the next conversion is complete, and the new conversion is placed in the output serial register. the adc must be configured for continuous conversion mode to use continuous read mode. to enable continuous read mode, set the contread bit in the interface mode register. when this bit is set, the only serial interface operations possible are reads from the data register. to exit con - tinuous read mode, issue a dummy read of the adc data register command (0x44) while the rdy output is low. alternatively, apply a software reset, that is, 64 sclk pulse s with cs = 0 and din = 1. this resets the adc and all register contents. these are the only commands that the interface recognizes after it is placed in continuous read mode. hold din low in continuous read mode until an instruction is to be written to the device. if multiple adc channels are enabled, each channel is output in turn, with the status bits being appended to the data if data_stat is set in the interface mode register. the status register indicates the channel to which the conversion corresponds. figure 68 . continuous read mode din sclk dout/rd y cs 0x02 data data data 0x0080 129 1 1-072
ad7175- 8 data sheet rev. 0 | page 38 of 64 single conversion mo de in single conversion mode, the ad7175 - 8 performs a single conversion and is placed in standby mode after the conversion is complete. the rdy output goes low to indicate the completion of a conversion . when the data - word has been read from the data register, the dout/ rdy pin goes high. the data register can be read several times, if required, even when the dout/ rdy pin has gon e high. if several channels are enabled, the adc automatically sequences through the enabled channels and performs a conversion on each channel. when a conversion is started, the dout/ rdy pin goes high and remains high until a valid conversion is available and cs is low. as soon as the conversion is available, the rdy output goes low. the adc then selects the next channel and begins a conversion. the user can read the present conversion while the next conversion is being performed. as soon as the next conversion is complete, the data register is updated; therefore, the user has a limited period in which to read the conversion. when the adc has performed a single conversion on each of the select ed channels, it returns to standby mode. if the data_stat bit in the interface mode register is set to 1, the contents of the status register, along with the conversion, are output each time the data register is read . the two lsbs of the status register in dicate the channel to which the conversion corresponds . figure 69 . single conversion mode din sclk dout/rdy cs 0x01 0x44 data 0x8010 129 1 1-073
data sheet ad7175- 8 rev. 0 | page 39 of 64 standby and power - down modes in standby mode, most blocks are powered down. the ldos remain active so that registers maintain their contents. the internal reference remains active if enabled, and the crystal oscillator remains active if selected. to power down the reference in standby mode, set the ref_en bit in the adc mod e reg i s ter to 0. to power down the clock in standby mode, set the clocksel bits in the adc mode register to 00 (internal oscillator). in power - down mode, all blocks are powered down, including the ldos. all registers lose their contents, and the gpio x outputs are placed in three - state. to prevent accidental entry to power - down mode, the adc must first be placed in standby mode. exiting power - down mode requires 64 sclk pulse s with cs = 0 and din = 1, that is, a serial interface reset. a delay of 500 s is recommended before issuing a subsequent serial interface command to allow the ldo to power up. figure 19 shows the internal reference se ttling time after returning from standby mode (setting ref_en = 0 and then 1) and returning from power down. calibration the ad7175 - 8 allows a two - point calibration to be performed to eliminate any offset and gain errors. three calibration modes eliminate these offset and gain errors on a per setup basis: ? internal zero - scale calibrati on mode ? system zero - scale calibration mode ? system full - scale calibration mode there is no internal full - scale calibration mode because this is calibrated in the factory at the time of production. only one channel can be active during calibration. after eac h conversion, the adc conversion result is scaled using the adc calibration registers before being written to the data register. the default value of the offset register is 0x800000, and the nominal value of the gain register is 0x555555. the calibration range of the adc gain is from 0.4 v ref to 1.05 v ref . the following equations show the calculations that are used. in unipolar mode, the ideal relationship that is, not taking into account the adc gain error and offset error is as follows: ( ) ? ? ? ? ? ? ? ? ? ? = gain offset v v data ref in in ipolar moe te ieal relationsip tat is not tain into aount te dc ain error an offset error is as follos: ( ) + ? ? ? ? ? ? ? ? ? ? = gain offset v v data ref in to start a aliration rite te relevant value to te moe its in te dc moe rei ster te dot rd pin an te rd it in te status reister o i en te aliration initiates en te aliration is omplete te ontents of te orrespon in offset or ain reister are upate t e rd it in te status reister is reset an te rd output pin returns lo if cs is lo an te d1 reverts to stan moe durin an internal offset aliration te selete positive analo input pin is isonnete an ot moulator inputs are onnete internall to te selete neative analo input pin for tis reason it is neessar to ensure tat te voltae on te selete neative analo input pin oes not exee te alloe limits an is free from exessive noise an interferene sstem ali rations oever expet te sstem ero sale offset an sstem full sale ain voltaes to e applie to te dc pins efore initiatin te aliration moes s a result errors external to te dc are remove from an operational point of vie tre at a aliration lie anoter dc onversion n offset aliration if reuire must alas e performe efore a full sale aliration set te sstem softare to monitor te rd it in te status reister or te rd output to etermine te en of a aliration via a pollin seuene or an interrupt riven routine ll alirations reuire a time eual to te settlin time of te selete filter an output ata rate to e omplete n internal offset aliration sstem ero sale aliration an sstem full sale aliration an e performe at an output ata rate sin loer output ata rates results in etter aliration aura an is aurate for all output ata rates ne offset aliration is reuire for a iven annel if te referene soure for tat annel is ane te offset error is tpiall 0 v an an offset aliration reues te offset error to te orer of te noise te ain error is fator alirate at amient temperature folloin tis aliration te ain error is tpiall 0 ppm of fsr te d1 provies te user it aess to te on ip aliration reisters alloin te miroproessor to rea te aliration oeffiients of te evie an to rite its on aliration oeffiients rea or rite of te offset an ain reisters an e performe at an time exept urin an internal or self aliration
ad7175- 8 data sheet rev. 0 | page 40 of 64 digital interface the programmable functions of the ad7175 - 8 are controlled via the spi serial interface. the serial interface of the ad7175 - 8 consists of four signals: cs , din, sclk, and dout/ rdy . the din input is used to transfer data into the on - chip registe rs, and the dout output is used to access data from the on - chip registers. sclk is the serial clock input for the device, and all data transfers (either on the din input or on the dout output) occur with respect to the sclk signal. the dout/ rdy pin also functions as a data ready signal, with the output going low if cs is low when a new data - word is available in the data register. the rdy output is reset high when a read operation from the data register is complete. the rdy output also goes high before updating the data register to indicate when not to read from the device to ensure that a data read is not attempted while the register is being updated. take care to avoid reading from the data register when the rdy output is about to go low. the best method to ensure that no data read occurs is to always monitor the rdy out put; start reading the data register as soon as the rdy output goes low; and ensure a sufficient sclk rate, such that the read is complete before the next conversion result . cs is used to select a device. it ca n be used to decode the ad7175 - 8 in systems where several components are connecte d to the serial bus. figure 2 and figure 3 show timing diagrams for interfacing to the ad7175 - 8 using c s to decode the device. figure 2 shows the timing for a read operation from the ad7175 - 8 , and figure 3 shows the timing for a write operation to the ad7175 - 8 . it is possible to read fr om the data register several times even though the rdy output returns high after the first read operation. however, care must be taken to ensure that the read operations are completed before the next output update occurs. in continuo us read mode, the data register can be read only once. the serial interface can operate in 3 - wire mode by tying cs low. in this case, the sclk, din, and dout/ rdy pins are used to communicate with the ad7175 - 8 . the end of the conversion can also be monitored using the rdy bit in the status register. the ad7175 - 8 can be reset by writing 64 sclks wit h cs = 0 and din = 1. a reset returns the interface to the state in which it expects a write to the communications register. this operation resets the contents of all registers to their power - on values. following a reset, allow a per iod of 500 s before addressing the serial interface. checksum protection the ad7175 - 8 has a checksum mode that can be used to improve interface robustness. using the checksum ensures that only valid data is written to a register and allows data read from a register to be validated. if an error occurs during a register write, the cr c_error bit is set in the status register. however, to ensure that the register write is successful, read back the register and verify the checksum. for crc checksum calculations during a write operation, the following polynomial is always used: x 8 + x 2 + x + 1 during read operations, the user can select between this polynomial and a simpler exclusive or ( xor ) function. the xor function requires less time to process on the host microcontroller than the polynomial - based checksum. the crc_en bits in the inte rface mode register enable and disable the checksum and allow the user to select between the polynomial check and the simple xor check. the checksum is appended to the end of each read and write transaction. the checksum calculation for the write transacti on is calculated using the 8 - bit command word and the 8 - bit to 24- bit data. for a read transaction, the checksum is calculated using the command word and the 8 - bit to 32 - bit data output. figure 70 and figure 71 show spi write and read transactions, respectively. figure 70 . spi write transaction with crc figure 71 . spi read transaction with crc if checksum protection is enabled when continuous read mode is active, an implied read data command of 0x44 before every data transmission must be account ed for when calculating the checksum value. this implied read data command ensures a nonzero checksum value even if the adc data equals 0x000000. 8-bit command 8-bit crc u p t o 24-bit input cs data crc cs din sclk 129 1 1-074 8-bit command 8-bit crc up to 32-bit output cmd data crc cs din sclk dout/ rdy 12911-075
data sheet ad7175- 8 rev. 0 | page 41 of 64 crc calculation polynomial the checksum, which is eight bits wide, is generated using the polynomial x 8 + x 2 + x + 1 to generate the checksum, the data is left shifted by eight bits to create a number ending in eight logic 0s. the polynomial is aligned so that its msb is adjacent to the leftmost logic 1 of the data. an xor function is applied to the data to pr oduce a new, shorter number. the polynomial is again aligned so that its msb is adjacent to the leftmost logic 1 of the new result, and the proce - dure is repeated. this process repeats until the original data is reduced to a value less than the polynomial. this is the 8 - bit checksum. example of a polynomial crc calculation 24- bit word: 0x654321 (eight command bits and 16 - bit data) an example of generating the 8 - bit checksum using the polynomial based checksum is as follows: initial value 011001010100001100100001 01100101010000110010000100000000 left shifted eight bits x 8 + x 2 + x + 1 = 100000111 polynomial 100100100000110010000100000000 xor result 100000111 polynomial 100011000110010000100000000 x or result 100000111 polynomial 11111110010000100000000 xor result 100000111 polynomial value 1111101110000100000000 xor result 100000111 polynomial value 111100000000100000000 xor result 100000111 polynomial value 11100111000100000000 xor result 100000111 polynomial value 1100100100100000000 xor result 100000111 polynomial value 100101010100000000 xor result 100000111 polynomial value 101101100000000 xor result 100000111 polynomial value 1101011000000 xor result 100000111 polynomial value 101010110000 xor result 100000111 polynomial value 1010001000 xor result 100000111 polynomial value 10000110 checksum = 0x86
ad7175- 8 data sheet rev. 0 | page 42 of 64 xor calculation the checksum, which is 8 bits wide, is generated by splitting the data into bytes and then performing an xor of the bytes. example of an xor calculation 24 - bit word: 0x 654321 (eight command bits and 16 - bit data) using the previous example of a polynomial crc calculation , divide the data into three bytes: 0x65, 0x43, and 0x21 01100101 0 x 65 01000011 0x43 00100110 xor result 00100001 0x21 00000111 crc
data sheet ad7175- 8 rev. 0 | page 43 of 64 integrated functions the ad7175 - 8 has integrated functions that improve the usefulness of a number of applications as well as serve diagnostic purposes in safety conscious applications. general - purpose i/o the ad7175 - 8 has two general - p urpose digital input/output pins (gpio0, gpio1) and two general - purpose digital output pins (gpo2, gpo3). as the naming convention suggests, the gpio0 and gpio1 pins can be configured as inputs or outputs, but gpo2 and gpo3 are outputs only. the gpio x and gpo x pins are enabled using the following bits in the gpiocon register: ip_en0, ip_en1 (or op_en0, op_en1) for gpio0 and gpio1, and op_en2_3 for gpo2 and gpo3. when the gpio0 or gpio1 pin is enabled as an input, the logic level at the pin is contained in t he gp_data0 or gp_data1 bit, respectively. when the gpio0, gpio1, gpo2, or gpo3 pin is enabled as an output, the gp_data0, gp_data1, gp_data2, or gp_data3 bit, respectively, determines the logic level output at the pin. the logic levels for these pins are referenced to avdd1 and avss; therefore, outputs have an amplitude of 5 v. the error pin can also be used as a general - purpose output. when the err_en bits in the gpiocon register are set to 11, the error pin operates as a general - purpose output. in this configuration, the err_dat bit in the gpiocon register determines the logic level output at the pin. the logic level for the pin is referenced to iovdd and dgnd. both gpios and the error pin, when set as general - purpose outputs, have an active pull - up circuit . external multiplexer control if an external multiplexer is used to increase the channel count, the multiplexer logic pins can be controlled via the ad7175 - 8 gpiox pins. with the mux_io bit, the gpiox timing is controlled by the adc; therefore, the channel change is synchronized with the adc, eliminating any need for external synchronization. delay it is possible to insert a programmable delay before the ad7175 - 8 begins to take samples. this delay allows an external amplifier or multiplexer to settle and can alleviate the specification requirements for the external amplifier or multiplexer. ei ght programmable settings, ranging from 0 s to 1 ms, can be set using the delay bits in the adc mode register (register 0x01, bits[10:8]). if a delay greater than 0 s is selected and the hide_delay bit in the adc mode register is set to 0, this delay is added to the conversion time, regardless of the selected output data rate. when using the sinc5 + sinc1 filter, it is possible to hide this delay such that the output data rate remains the same as the output data rate without the delay enabled. if the hide _delay bit is set to 1 and the selected delay is less than half of the conversion time, the delay can be absorbed by reducing the number of averages the digital filter performs, which keeps the conversion time the same but can affect the noise performance. the effect on the noise performance depends on the delay time compared to the conversion time. it is possible to absorb the delay only for output data rates less than 10 ksps with the exception of the following four rates, which cannot absorb any delay: 397.5 sps, 59.92 sps, 49.96 sps, and 16.66 sps. 16- bit/24 - bit conversions by default, the ad7175 - 8 generates 24 - bit conversions. however, the width of the conversions can be reduced to 16 bits. setting the wl16 bit in the interface mode register to 1 rounds all data conversions to 16 bits. clearing this bit sets the width of the data c onversions to 24 bits. dout_reset the serial interface uses a shared dout/ rdy pin. by default, this pin outputs the rdy signal. during a data read, this pin outputs the data from the register being read. after the read i s complete, the pin reverts to outputting the rdy signal after a short fixed period of time (t 7 ). however, this time may be too short for some microcontrollers and can be extended until the cs pin is brought high by sett ing the dout_reset bit in the interface mode register to 1. this means that cs must be used to frame each read operation and compete the serial interface transaction. synchronization normal synchronization when the sync_en bit in the gpio con register is set to 1, the sync pin functions as a synchronization input. the sync input lets the user reset the modulator and the digital filter without affecting any of the setup conditions on the device . this feature lets the user start to gather samples of the analog input from a known point, the rising edge of the sync input. the sync input must be low for at least one master clock cycle to ensure that synchronizatio n occurs. if multiple ad7175 - 8 devices are operated from a common master clock, t hey can be synchronized so that their analog inputs are sampled simultaneously. this synchronization is normally done after each ad7175 - 8 device has performed its own calibration or has calibration coefficients loaded into its calibration registers. a falling edge on the sync input resets the digital filter and the an alog modulator and places the ad7175 - 8 into a consistent known state. while the sync input is low, the ad7175 - 8 is maintained in this known stat e. on the sync input rising edge, the modulator and filter are taken out of this reset state, and on the next master clock edge, the device starts to gather input samples again. the device is taken out of reset on the master clock falling edge following the sync input low to high transition. therefore,
ad7175- 8 data sheet rev. 0 | page 44 of 64 when multiple devices are being synchronized, take the sync input high on the master clock rising edge to ensure that all devices are released on the master clock falling edge. if the sync input is not taken high in sufficient time, a difference of one master clock cycle between the devices is possible ; that is, the instant at which conversions are available differs from device to device by a maximum of one master clock cycle. the sync input can also be used as a start conversion command for a single channel when in normal synchronizat ion mode. in this mode, the rising edge of the sync input starts a conversion, and the falling edge of the rdy output indicates when the conversion is complete. the settling time of the filter is required for each data r egister update. after the conversion is complete, bring the sync input low in preparation for the next conversion start signal. alternate synchronization in alternate synchronization mode, the sync input operates as a st art conversion command when several channels of the ad7175 - 8 are enabled. setting the alt_sync bit in the interface mode register to 1 enables an alternate synchronization scheme. when the sync input is taken low, the adc completes the conversion on the current channel, selects the next channel in the sequence, and then waits until the sync input is taken high to commence the conversion. the rdy output goes low when the conversion is complete on the current channel, and the data register is updated with the corresponding conversion . therefore, the sync input does not interfere with the sampling on the currently selected channel but allows the user to control the instant at which the conversion begins on the next channel in the sequence. alternate synchronization mo de can be used only when several channels are enabled. it is not recommended to use this mode when a single channel is enabled. error flags the status register contains three error bits adc_error, crc_error, and reg_error that flag errors with the adc conv ersion, errors with the crc check, and errors caused by changes in the registers, respectively. in addition, the error output can indicate that an error has occurred. adc_error the adc_error bit in the status register flags any errors that occur during the conversion process. the flag is set when an over - range or underrange result is output from the adc. the adc also outputs all 0s or all 1s when an undervoltage or overvoltage oc curs. this flag is reset only when the overvoltage or undervoltage is removed. it is not reset by a read of the data register. crc_error if the crc value that accompanies a write operation does not correspond with the information sent, the crc_error flag i s set. the flag is reset as soon as the status register is explicitly read. reg_error the re g _error flag is used in conjunction with the reg_check bit in the interface mode register. when the reg_check bit is set, the ad7175 - 8 monitors the values in the on - chip registers. if a bit changes, the reg_error bit is set. therefore, for write s to the on - chip registers, set reg_check to 0. when the registers have been updated, the reg_check bit can be set to 1. the ad7175 - 8 c alculates a checksum of the on - chip registers. if one of the register values has changed, the reg_error bit is set. if an error is flagged, set reg_check to 0 to clear the reg_error bit in the status re gister. the register check function does not monitor the data register, status register, or interface mode register. error input/output the error pin functions as an error input/output pin or a general - purpose output pin . the err_en bits in the gpiocon register determine the function of the pin. when err_en is set to 10, the error pin functions as an open - drain error output, error . the three error bits in the status register (adc_error, crc_error, and reg_error) are ored, inverted, and mapped to the error output. therefore, the error output indicates that an error has occurred. the status regist er must be read to identify the error source. when err_en is set to 01, the error pin functions as an error input, error . the error output of another component can be connected to the ad7175 - 8 error input so that the ad7175 - 8 indicates when an error occurs on either itself or the external component. the value on the error input is inverted and o re d with the errors from the adc conversion, and the result is indicated via the adc_error bit in the status register. the value of the error input is reflected in the err_dat bit in the gpio configuration register. the er ror input/output is disabled when err_en is set to 00. when the err_en bits are set to 11, the error pin operates as a general - purpose output. data_stat the contents of the status register can be appended to each con - version on the ad7175 - 8 . this function is useful if several channels are enabled. each time a conv ersion is output, the contents of the status register are appended. the two lsbs of the status register indicate to which channel the conversion corresponds. in addition, the user can determine if any errors are being flagged by the error bits. iostrength the serial interface can operate with a power supply as low as 2 v. however, at this low voltage, the dout/ rdy pin may not have sufficient drive strength if there is moderate parasitic capacitance on the board or the sclk frequency is hi gh. the
data sheet ad7175- 8 rev. 0 | page 45 of 64 iostrength bit in the interface mode register increases the drive strength of the dout/ rdy pin. power - down switch setting the pdsw bit in the gpio configuration register allows the pdsw pin to sink current. this function can be used in applications where the switch controls the power - up/power - down of the analog front - end sensor, for example, a bridge sensor. the pdsw pin can sink 16 ma maximum. internal temperature sensor the ad7175 - 8 has an integrated temperature sensor. the temperature sensor can be used as a guide for the ambient temperature at which the d evice is operating. this can be used for diagnostic purposes or as an indicator of when the applica - tion circuit needs to rerun a calibration routine to take into account a shift in operating temperature. the temperature sensor is selected using the crossp oint multiplexer and is selected in the same way as an analog input channel. the temperature sensor requires that the analog input buffers be enabled on both analog inputs. if the buffers are not enabled , selecting the temperature sensor as an input forces the buffers to be enabled during the conversion. to use the temperature sensor, the first step is to calibrate the device in a known temperature (25c) and take a conversion as a reference point. the temperature sensor has a nominal sensitivity of 47 0 v/ k; use the difference in this ideal slope and the slope measured to calibrate the temperature sensor. the temperature sensor is specified with a 2c typical accuracy after calibration at 25c. the temperature can be calculated as follows: 15 . 273 C v 0 47 c) ( ? ? ? ? ? ? ? ? = result conversion e temperatur
ad7175- 8 data sheet rev. 0 | page 46 of 64 grounding and layout the analog inputs and reference inputs are differential and, therefore, most of the voltages in the analog modulator are common - mode voltages. the high common - mode rejection of the device removes common - mode noise on these inputs. the analog and digital supplies to the ad7175 - 8 are independent and connected to separate pins to minimize coupling between the analog and digital sections of the device. the digital filter provides rejection of broadband noise on the pow er supplies, except at integer multiples of the master clock frequency. the digital filter also removes noise from the analog and reference inputs, provided that these noise sources do not saturate the analog modulator. as a result, the ad7175 - 8 is more immune to noise interference than a conventional high resolution converter. howeve r, because the resolution of the ad7175 - 8 is high and the noise levels from the converter are so low, take care with regard to grounding and layout. the pcb that houses the adc must be designed such that the analog and digital sections are separated and confined to certain areas of the board. a m inimum etch technique is generally best for ground planes because it results in the best shielding. in any layout, the user must consider the flow of currents in the system, ensuring that the paths for all return currents are as close as possible to the p a ths the currents took to reach their destinations . avoid running digital lines under the device because this couples noise onto the die and allow s the analog ground plane to run under the ad7175 - 8 to prevent noise coupling. the power supply lines to the ad7175 - 8 must use as wide a trace as possible to provide low impedance paths and reduce glitches on the power supply line. shield fast switching signals like clocks with digital ground to prevent radiating noise to other sections of the board and never run clock signals near the analog inputs. avoid crossover of digital and analog signals. run traces on opposite sides of the board at right angles to each other. this techni que reduces the effects of feed through on the board. a microstrip technique is by far the best method but is not always possible with a double sided board. good decoupling is important when using high resolution adcs. the ad7175 - 8 has three power supply pins av dd1, av dd2, and iovdd. the avdd1 and avdd2 pins are referenced to avss , and the iovdd pin is referenced to dgnd. decouple avdd1 and avdd2 with a 10 f capacitor in parallel with a 0.1 f capacitor to avss on each pin. place the 0.1 f capacitor as close as possible to the device on each supply, ideally right up against the d evice. decouple iovdd with a 10 f capacitor in parallel with a 0.1 f capacitor to dgnd. decouple all analog inputs to avss. if an external reference is used, decouple the ref+ and ref? pins to avss. the ad7175 - 8 also has two on - board ldo regulators one that regulates the avdd2 supply and one that regulates the iovdd supply. for the r egcapa pin, it is recommended that 1 f and 0.1 f capacitors to avss be used. similarly, for the regcapd pin, it is recommended that 1 f and 0.1 f capacitors to dgnd be used. if using the ad7175 - 8 for split supply operation, a separate plane must be used for avss.
data sheet ad7175- 8 rev. 0 | page 47 of 64 register summary table 24 . register summary reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x00 comms [7:0] wen r/ w ra 0x00 w 0x00 status [7:0] rdy adc_error crc_error reg_error channel 0x80 r 0x01 adcmode [15:8] ref_en hide_delay sing_cyc reserved delay 0xa000 rw [7:0] reserved mode clocksel reserved 0x02 ifmode [15:8] reserved alt_sync iostrength reserved dout_reset 0x0000 rw [7:0] contread data_stat reg_check reserved crc_en reserved wl16 0x03 regcheck [23:16] register_check[23:16] 0x000000 r [15:8] register_check[15:8] [7:0] register_check[7:0] 0x04 data [23:16] data[23:16] 0x000000 r [15:8] data[15:8] [7:0] data[7:0] 0x06 gpiocon [15:8] reserved pdsw op_en2_3 mux_io sync_en err_en err_dat 0x0800 rw [7:0] gp_data3 gp_data2 ip_en1 ip_en0 op_en1 op_en0 gp_data1 gp_data0 0x07 id [15:8] id[15:8] 0x3cdx r [7:0] id[7:0] 0x10 ch0 [15:8] ch_en0 setup_sel0 reserved ainpos0[4:3] 0x8001 rw [7:0] ainpos0[2:0] ainneg0 0x11 ch1 [15:8] ch_en1 setup_sel1 reserved ainpos1[4:3] 0x0001 rw [7:0] ainpos1[2:0] ainneg1 0x12 ch2 [15:8] ch_en2 setup_sel2 reserved ainpos2[4:3] 0x0001 rw [7:0] ainpos2[2:0] ainneg2 0x13 ch3 [15:8] ch_en3 setup_sel3 reserved ainpos3[4:3] 0x0001 rw [7:0] ainpos3[2:0] ainneg3 0x14 ch4 [15:8] ch_en4 setup_sel4 reserved ainpos4[4:3] 0x0001 rw [7:0] ainpos4[2:0] ainneg4 0x15 ch5 [15:8] ch_en5 setup_sel5 reserved ainpos5[4:3] 0x0001 rw [7:0] ainpos5[2:0] ainneg5 0x16 ch6 [15:8] ch_en6 setup_sel6 reserved ainpos6[4:3] 0x0001 rw [7:0] ainpos6[2:0] ainneg6 0x17 ch7 [15:8] ch_en7 setup_sel7 reserved ainpos7[4:3] 0x0001 rw [7:0] ainpos7[2:0] ainneg7 0x18 ch8 [15:8] ch_en8 setup_sel8 reserved ainpos8[4:3] 0x0001 rw [7:0] ainpos8[2:0] ainneg8 0x19 ch9 [15:8] ch_en9 setup_sel9 reserved ainpos9[4:3] 0x0001 rw [7:0] ainpos9[2:0] ainneg9 0x1a ch10 [15:8] ch_en10 setup_sel10 reserved ainpos10[4:3] 0x0001 rw [7:0] ainpos10[2:0] ainneg10 0x1b ch11 [15:8] ch_en11 setup_sel11 reserved ainpos11[4:3] 0x0001 rw [7:0] ainpos11[2:0] ainneg11 0x1c ch12 [15:8] ch_en12 setup_sel12 reserved ainpos12[4:3] 0x0001 rw [7:0] ainpos12[2:0] ainneg12 0x1d ch13 [15:8] ch_en13 setup_sel13 reserved ainpos13[4:3] 0x0001 rw [7:0] ainpos13[2:0] ainneg13 0x1e ch14 [15:8] ch_en14 setup_sel14 reserved ainpos14[4:3] 0x0001 rw [7:0] ainpos14[2:0] ainneg14 0x1f ch15 [15:8] ch_en15 setup_sel15 reserved ainpos15[4:3] 0x0001 rw [7:0] ainpos15[2:0] ainneg15 0x20 setupcon0 [15:8] reserved bi_unipolar0 refbuf0+ refbuf0 ? ainbuf0+ ainbuf0? 0x1320 rw [7:0] burnout_en0 reserved ref_sel0 reserved 0x21 setupcon1 [15:8] reserved bi_unipolar1 refbuf1+ refbuf1? ainbuf1+ ainbuf1? 0x1320 rw [7:0] burnout_en1 reserved ref_sel1 reserved 0x22 setupcon2 [15:8] reserved bi_unipolar2 refbuf2+ refbuf2? ainbuf2+ ainbuf2? 0x1320 rw [7:0] bur nout_en2 reserved ref_sel2 reserved 0x23 setupcon3 [15:8] reserved bi_unipolar3 refbuf3+ refbuf3? ainbuf3+ ainbuf3? 0x1320 rw [7:0] burnout_en3 reserved ref_sel3 reserved 0x24 setupcon4 [15:8] reserved bi_unipolar4 refbuf4+ refbuf4? ainbuf4+ ainbuf4? 0x1320 rw [7:0] burnout_en4 reserved ref_sel4 reserved
ad7175- 8 data sheet rev. 0 | page 48 of 64 reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x25 setupcon5 [15:8] reserved bi_unipolar5 refbuf5+ refbuf5? ainbuf5+ ainbuf5? 0x1320 rw [7:0] burnout_en5 reserved ref_sel5 reserved 0x26 setupcon6 [15:8] reserved bi_unipolar6 refbuf6+ refbuf6? ainbuf6+ ainbuf6? 0x1320 rw [7:0] burnout_en6 reserved ref_sel6 reserved 0x27 setupcon7 [15:8] reserved bi_unipolar7 refbuf7+ refbuf7? ainbuf7+ ainbuf7? 0x1320 rw [7:0] burnout_en7 reserved ref_sel7 reserved 0x28 filtcon0 [15:8] sinc3_map0 reserved enhfilten0 enhfilt0 0x0500 rw [7:0] reserved order0 odr0 0x29 filtcon1 [15:8] sinc3_map1 reserved enhfilten1 enhfilt1 0x0500 rw [7:0] reserved order1 odr1 0x2a filtcon2 [15:8] sinc3_map2 reserved enhfilten2 enhfilt2 0x0500 rw [7:0] reserved order2 odr2 0x2b filtcon3 [15:8] sinc3_map3 reserved enhfilten3 enhfilt3 0x0500 rw [7:0] reserved order3 odr3 0x2c filtcon4 [15:8] sinc3_map4 reserved enhfilten4 enhfilt4 0x0500 rw [7:0] reserved order4 odr4 0x2d filtcon5 [15:8] sinc3_map5 reserved enhfilten5 enhfilt5 0x0500 rw [7:0] reserved order5 odr5 0x2e filtcon6 [15:8] sinc3_map6 reserved enhfilten6 enhfilt6 0x0500 rw [7:0] reserved order6 odr6 0x2f filtcon7 [15:8] sinc3_map7 reserved enhfilten7 enhfilt7 0x0500 rw [7:0] reserved order7 odr7 0x30 offset0 [23:0] offset0[23:0] 0x800000 rw 0x31 offset1 [23:0] offset1[23:0] 0x800000 rw 0x32 offset2 [23:0] offset2[23:0] 0x800000 rw 0x33 offset3 [23:0] offset3[23:0] 0x800000 rw 0x34 offset4 [23:0] offset4[23:0] 0x800000 rw 0x35 offset5 [23:0] offset5[23:0] 0x800000 rw 0x36 offset6 [23:0] offset6[23:0] 0x800000 rw 0x37 offset7 [23:0] offset7[23:0] 0x800000 rw 0x38 gain0 [23:0] gain0[23:0] 0x5xxxx0 rw 0x39 gain1 [23:0] gain1[23:0] 0x5xxxx0 rw 0x3a gain2 [23:0] gain2[23:0] 0x5xxxx0 rw 0x3b gain3 [23:0] gain3[23:0] 0x5xxxx0 rw 0x3c gain4 [23:0] gain4[23:0] 0x5xxxx0 rw 0x3d gain5 [23:0] gain5[23:0] 0x5xxxx0 rw 0x3e gain6 [23:0] gain6[23:0] 0x5xxxx0 rw 0x3f gain7 [23:0] gain7[23:0] 0x5xxxx0 rw
data sheet ad7175- 8 rev. 0 | page 49 of 64 register details communications regis ter address: 0x00, reset: 0x00, name: comms all access to the on - chip registers must start with a write to the communications register. this write determines what register is accessed next and whether that operation is a write or a read. table 25 . bit descriptions for comms bits bit name settings description reset access 7 wen this bit must be low to begin communications with the adc. 0x0 w 6 r/ w this bit determines if the command is a read or write operation. 0x0 w 0 write command 1 read command [5:0] ra the register address bits determine which register is to be read from or written to as part of the current communication. 0x00 w 000000 status register 000001 adc mode register 000010 interface mode register 000011 register checksum register 000100 data register 000110 gpio configuration register 000111 id register 010000 channel 0 register 010001 channel 1 register 010010 channel 2 register 010011 channel 3 register 010100 channel 4 register 010101 channel 5 register 010110 channel 6 register 010111 channel 7 register 011000 channel 8 register 011001 channel 9 register 011010 channel 10 register 011011 channel 11 register 011100 channel 12 register 011101 channel 13 register 011110 channel 14 register 011111 channel 15 register 100000 setup configuration 0 register 100001 setup configuration 1 register 100010 setup configuration 2 register 100011 setup configuration 3 register 100100 setup configuration 4 register 100101 setup configuration 5 register 100110 setup configuration 6 register 100111 setup configuration 7 register 101000 filter configuration 0 register 101001 filter configuration 1 register 101010 filter configuration 2 register 101011 filter configuration 3 register 101100 filter configuration 4 register 101101 filter configuration 5 register 101110 filter configuration 6 register 101111 filter configuration 7 register
ad7175- 8 data sheet rev. 0 | page 50 of 64 bits bit name settings description reset access 110000 offset 0 register 110001 offset 1 register 110010 offset 2 register 110011 offset 3 register 110100 offset 4 register 110101 offset 5 register 110110 offset 6 register 110111 offset 7 register 111000 gain 0 register 111001 gain 1 register 111010 gain 2 register 111011 gain 3 register 111100 gain 4 register 111101 gain 5 register 111110 gain 6 register 111111 gain 7 register
data sheet ad7175- 8 rev. 0 | page 51 of 64 status register address: 0x00, reset: 0x80, name: status the status register is an 8 - bit register that contains adc and serial interface status information. it can optionally be appended to the data register by setting the data_stat bit in the interface mode register. table 26 . bit descriptions for status bits bit name settings description reset access 7 rdy the status of rdy is output to the dout/ rdy pin whenever cs is low and a register is not being read. this bit goes low when the adc has written a new resul t to the data register. in adc calibration modes, this bit goes low when the adc has written the calibration result. rdy is brought high automatically by a read of the data register. 0x1 r 0 new data result available 1 awaiting new data result 6 adc_error this bit by default indicates if an adc overrange or underrange has occurred. the adc result is clamped to 0xffffff for overrange errors and 0x000000 for underrange errors. this bit is updated when the adc result is written and is cleared at the next update after removing the overrange or underrange condition. 0x0 r 0 no error 1 error 5 crc_error this bit indicates if a crc error has taken place during a register write. for register reads, the host microcontroller determines if a crc error has occurred. this bit is cleared by a read of this register. 0x0 r 0 no error 1 crc error 4 reg_error this bit indicates if the content of one of the internal registers has changed from the value calculated when the register integrity check was activated. the check is activated by setting the reg_check bit in the interface mode register. this bit is cleared by clearing the reg_check bit. 0x0 r 0 no error 1 error [3:0] channel these bits indicate which channel was active for the adc conversion whose result is currently in the data register. this may be different from the channel currently being converted. the mapping is a direct map from the channel register; therefore, channel 0 results in 0x0 and channel 15 results in 0xf. 0x0 r 0000 channel 0 0001 channel 1 0010 channel 2 0011 channel 3 0100 channel 4 0101 channel 5 0110 channel 6 0111 channel 7 1000 channel 8 1001 channel 9 1010 channel 10 1011 channel 11 1100 channel 12 1101 channel 13 1110 channel 14 1111 channel 15
ad7175- 8 data sheet rev. 0 | page 52 of 64 adc mode register address: 0x01, reset: 0xa000 , name: adcmode the adc mode register controls the operating mode of the adc and the master clock selection. a write to the adc mode register resets the filter and the rdy bits and starts a new conversion or calibration. table 27 . bit descriptions for adcmode bits bit name settings description reset access 15 ref_en enables internal reference and outputs a buffered 2.5 v to the refout pin. 0x1 rw 0 disabled 1 enabled 14 hide_delay if a programmable delay is set using the delay bits, this bit allows the delay to be hidden by absorbing the delay into the conversion time for selected data rates with the sinc5 + sinc1 filter. see the delay section for more information. 0x0 rw 0 enabled 1 disabled 13 sing_cyc this bit can be used when only a single channel is active to set the adc to only output at the settled filter data rate. 0x 1 rw 0 disabled 1 enabled [12:11] reserved these bits are reserved; set these bits to 0. 0x0 r [10:8] delay these bits allow a programmable delay to be added after a channel switch to allow the settling of external circuitry before the adc starts processing its input. 0x0 rw 000 0 s 001 4 s 010 16 s 011 40 s 100 100 s 101 200 s 110 500 s 111 1 ms 7 reserved this bit is reserved; set this bit to 0. 0x0 r [6:4] mode these bits control the operating mode of the adc. see the operating modes section for more information. 0x0 rw 000 continuous conversion mode 001 single conversion mode 010 standby mode 011 power - down mode 100 internal offset calibration 110 system offset calibration 111 system gain calibration [3:2] clocksel th e s e bit s are used to select the adc clock source. selecting the internal oscillator also enables the internal oscillator. 0x0 rw 00 internal oscillator 01 internal oscillator output on the xtal2/clkio pin 10 external clock input on the xtal2/clkio pin 11 external crystal on the xtal1 and xtal2/clkio pins [1:0] reserved these bits are reserved; set these bits to 0. 0x0 r
data sheet ad7175- 8 rev. 0 | page 53 of 64 interface mode regis ter address: 0x02, reset: 0x0000, name: ifmode the interface mode register configures various serial interface options. table 28 . bit descriptions for ifmode bits bit name settings description reset access [15:13] reserved these bits are reserved; set these bits to 0. 0x0 r 12 a lt_ sync this bit enables a different behavior of the sync pin to allow the use of sync as a control for conversions when cycling channels (see the description of the sync_en bit in the gpio configuration register section for details). 0x0 rw 0 disabled 1 enabled 11 iostrength this bit controls the drive strength of the dout/ rdy pin. set this bit when reading from the serial interface at high speed with a low iovdd supply and moderate capacitance. 0x0 rw 0 disabled (default) 1 enabled [10:9] reserved these bits are reserved; set these bits to 0. 0x0 r 8 dout_reset see the dout_reset section for more information. 0x0 rw 0 disabled 1 enabled 7 contread this bit enables the continuous read mode of the adc data register. the adc must be configured in continuous conversion mode to use continuous read mode . for more details, see the operating modes section. 0x0 rw 0 disabled 1 enabled 6 data_stat this bit enables the status register to be appended to the data register when read so that channel and status information are transmitted with the data. this is the only way to be sure that the channel bits read from the status register correspond to the d ata in the data register. 0x0 rw 0 disabled 1 enabled 5 reg_check this bit enables a register integrity checker, which can be used to monitor any change in the value of the user registers. to use this feature, configure all other registers as desired with this bit cleared. then write to this register to set the reg_check bit to 1. if the contents of any of the registers change, the reg_error bit is set in the status register. to clear the error, set the reg_check bit to 0. neither the interface mode register nor the adc data or status registers are included in the registers that are checked. if a register must have a new value written, this bit must first be cleared; otherwise, an error is flagged when the new register contents are written. 0x0 rw 0 disabled 1 enabled 4 reserved this bit is reserved; set this bit to 0. 0x0 r [3:2] crc_en these bits e nable crc protection of register reads/writes. crc increases the number of bytes in a serial interface transfer by one. see the crc calculation section for more details. 0x00 rw 00 disabled 01 xor checksum enabled for register read transactions; register writes still use crc with these bits set 10 crc checksum enabled for read and write transactions 1 reserved this bit is reserved; set this bit to 0. 0x0 r
ad7175- 8 data sheet rev. 0 | page 54 of 64 bits bit name settings description reset access 0 wl16 this bit c hanges the adc data register to 16 bits. the adc is not reset by a write to the interface mode register; therefore, the adc result is not rounded to the correct word length immediately after writing to these bits. the first new adc result is correct. 0x0 rw 0 24 - bit data 1 16 - bit data register check address: 0x03, reset: 0x000000, name: regcheck the register check register is a 24 - bit checksum calculated by exclusively or'ing the contents of the user registers. the reg_check bit in the interface mode register must be set for this to operate; otherwise, the register reads 0. table 29 . bit descriptions for regcheck bits bit name settings description reset access [23:0] register_check this register contains the 24 - bit checksum of user registers when the reg_check bit is set in the interface mode register. 0x000 000 r data register address: 0x04, reset: 0x000000, name: data the data register contains the adc conversion result. the encoding is offset binary, or it can be changed to unipolar by the bi_unipolarx bit s in the setup configuration registers. reading the data register brings the rdy bit and the rdy output high if it is low. the adc result can be read multiple times; however, because the rdy output is brought high, it is not possible to know if another adc result is imminent. after the command to read the adc register is received, the adc does not write a new result into the data register. table 30 . bit descriptions fo r data bits bit name settings description reset access [23:0] data this register contains the adc conversion result. if data_stat is set in the interface mode register, the status register is appended to this register when read, making this a 32 - bit register. if wl16 is set in the interface mode register, this register is reduced to 16 bits. 0x000000 r
data sheet ad7175- 8 rev. 0 | page 55 of 64 gpio configuration r egister address: 0x06, reset: 0x0800, name: gpiocon the gpio configuration register controls the general - purpose i/o pins of the adc. table 31 . bit descriptions for gpiocon bits bit name settings description reset access 15 reserved these bits are reserved; set these bits to 0. 0x0 r 14 pdsw this bit enables/disables the power - down switch function. setting the bit allows the pin to sink current. this function can be used for bridge sensor applications where the switch controls the power - up/power - down of the bridge. 0x0 rw 13 op_en2_3 this bit enables the gpo2 and gpo3 pins. outputs are referenced between avdd1 and avss. 0x0 rw 12 mux_io this bit allows the adc to control an external multiplexer, using gpio0/gpio1/ gpo2/gpo3 in sync with the internal channel sequencing. the analog input pins used for a channel can still be selected on a per channel basis. therefore, it is possible to have a 16 - channel multiplexer in front of each analog input pair (ain0/ain1 to ain14/ain15) , giving a total of 128 differential channels. however, only 16 channels at a time can be automatically sequenced. following the sequen ce of 16 channels, the user changes the analog input to the next pair of input channels, and it sequence s through the next 16 channels. a delay can be inserted after switching an external multiplexer (see the delay bits in the adc mode register section). 0x0 rw 11 sync_en this bit enables the sync pin as a sync hronization input. when the pin is low, this holds the adc and filter in reset until the sync pin goes high. an alternative operation of the sync pin is available when the alt_sync bit in the interface mode register is se t. this mode only works when multiple channels are enabled. in this case, a low on the sync pin does not immediately reset the filter/modulator. instead, if the sync pin is low when the channel is due to be swi tched, the modulator a nd filter are prevented from starting a new conversion. bringing sync high begins the next conversion. this alternative sync mode allows sync to be used while cycling through channels. 0x1 rw 0 disabled. 1 enabled. [10:9] err_en these bits enable the error pin as an error input/output. 0x0 rw 00 disabled. 01 error is an error input. the (inverted) readback state is or'ed with other error sources and is available in the adc_error bit in the status register. the error pin state can also be read from the err_dat bit in this register. 10 error is an open - drain error output. the status register error bits are or'ed, inverted, and mapped to the error pin. the error pins of multiple devices can be wired together to a common pull - up resistor so that an error on any device can be observed. 11 error is a general - purpose output. the status of the pin is controlled by the err_dat bit in this register. this output is referenced between iovdd and dgnd, as opposed to the avdd1 and avss levels used by the general - purpose i/o pins. the err or pin has an active pull - up in this case. 8 err_dat this bit determines the logic level at the error pin if the pin is enabled as a general - purpose output. this bit reflects the readback status of the pin if the pin is enabled as an input. 0x0 rw 7 gp_data3 this bit is the write data for gpo3. 0x0 w 6 gp_data2 this bit is the write data for gpo2. 0x0 w 5 ip_en1 this bit turns gpio1 into an input. inputs are referenced to avdd1 or avss. 0x0 rw 0 disabled. 1 enabled. 4 ip_en0 this bit turns gpio0 into an input. inputs are referenced to avdd1 or avss. 0x0 rw 0 disabled. 1 enabled.
ad7175- 8 data sheet rev. 0 | page 56 of 64 bits bit name settings description reset access 3 op_en1 this bit turns gpio1 into an output. outputs are referenced between avdd1 and avss. 0x0 rw 0 disabled. 1 enabled. 2 op_en0 this bit turns gpio0 into an output. outputs are referenced between avdd1 and avss. 0x0 rw 0 disabled. 1 enabled. 1 gp_data1 this bit is the readback or write data for gpio1. 0x0 rw 0 gp_data0 this bit is the readback or write data for gpio0. 0x0 rw id register address: 0x07, reset: 0x3cdx, name: id the id register returns a 16 - bit id. for the ad7175 - 8 , this id is 0x3cdx. table 32 . bit descriptions for id bits bit name settings description reset access [15:0] id the id register returns a 16 - bit id code that is specific to the adc. 0x3cdx r 0x3cdx ad7175 -8 channel register 0 address: 0x10, reset: 0x8001, name: ch0 the channel registers are 16 - bit registers used to select which channels are currently active, which inputs are selected for each channel, and which setup is used to configure the adc for that channel. table 33 . bit descriptions for ch0 bits bit name settings description reset access 15 ch_en0 this bit enables channel 0. if more than one channel is enabled, the adc automatically sequences between them. 0x1 rw 0 disabled 1 enabled (default) [14:12] setup_sel0 these bits identify which of the eight setups is used to configure the adc for this channel. a setup comprises a set of four registers: setup configuration register , filter configuration register, offset register, and gain register. all channels can use the same set up, in which case the same 3 - bit value must be written to these bits on all active channels, or up to eight channels can be configured differently. 0x0 rw 000 setup 0 001 setup 1 010 setup 2 011 setup 3 100 setup 4 101 setup 5 110 setup 6 111 setup 7 [11:10] reserved these bits are reserved; set these bits to 0. 0x0 r [9:5] ainpos0 these bits select which input is connected to the positive input of the adc for this channel. 0x0 rw 00000 ain0 (default) 00001 ain1 00010 ain2 00011 ain3 00100 ain4 00101 ain5 00110 ain6 00111 ain7
data sheet ad7175- 8 rev. 0 | page 57 of 64 bits bit name settings description reset access 01000 ain8 01001 ain9 01010 ain10 01011 ain11 01100 ain12 01101 ain13 01110 ain14 01111 ain15 10000 ain16 10001 temperature sensor+ 10010 temperature sensor? 10011 ((avdd1 ? avss)/5)+ (analog input buffers must be enabled) 10100 ((avdd1 ? avss)/5)? (analog input buffers must be enabled) 10101 ref+ 10110 ref? [4:0] ainneg0 these bits select which input is connected to the negative input of the adc for this channel. 0x1 rw 00000 ain0 00001 ain1 (default) 00010 ain2 00011 ain3 00100 ain4 00101 ain5 00110 ain6 00111 ain7 01000 ain8 01001 ain9 01010 ain10 01011 ain11 01100 ain12 01101 ain13 01110 ain14 01111 ain15 10000 ain16 10001 temperature sensor+ 10010 temperature sensor? 10011 ((avdd1 ? avss)/5)+ 10100 ((avdd1 ? avss)/5)? 10101 ref+ 10110 ref?
ad7175- 8 data sheet rev. 0 | page 58 of 64 channel register 1 t o channel register 1 5 address: 0x11 to 0x1f, reset: 0x0001, name: ch1 to ch7 the remaining 15 channel registers share the same layout as channel register 0. table 34 . ch1 to ch15 register map reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x11 ch1 [15:8] ch_en1 setup_sel1 reserved ainpos1[4:3] 0x0001 rw [7:0] ainpos1[2:0] ainneg1 0x12 ch2 [15:8] ch_en2 setup_sel2 reserved ainpos2[4:3] 0x0001 rw [7:0] ainpos2[2:0] ainneg2 0x13 ch3 [15:8] ch_en3 setup_sel3 reserved ainpos3[4:3] 0x0001 rw [7:0] ainpos3[2:0] ainneg3 0x14 ch4 [15:8] ch_en4 setup_sel4 reserved ainpos4[4:3] 0x0001 rw [7:0] ainpos4[2:0] ainneg4 0x15 ch5 [15:8] ch_en5 setup_sel5 reserved ainpos5[4:3] 0x0001 rw [7:0] ainpos5[2:0] ainneg5 0x16 ch6 [15:8] ch_en6 setup_sel6 reserved ainpos6[4:3] 0x0001 rw [7:0] ainpos6[2:0] ainneg6 0x17 ch7 [15:8] ch_en7 setup_sel7 reserved ainpos7[4:3] 0x0001 rw [7:0] ainpos7[2:0] ainneg7 0x18 ch8 [15:8] ch_en8 setup_sel8 reserved ainpos8[4:3] 0x0001 rw [7:0] ainpos8[2:0] ainneg8 0x19 ch9 [15:8] ch_en9 setup_sel9 reserved ainpos9[4:3] 0x0001 rw [7:0] ainpos9[2:0] ainneg9 0x1a ch10 [15:8] ch_en10 setup_sel10 reserved ainpos10[4:3] 0x0001 rw [7:0] ainpos10[2:0] ainneg10 0x1b ch11 [15:8] ch_en11 setup_sel11 reserved ainpos11[4:3] 0x0001 rw [7:0] ainpos11[2:0] ainneg11 0x1c ch12 [15:8] ch_en12 setup_sel12 reserved ainpos12[4:3] 0x0001 rw [7:0] ainpos12[2:0] ainneg12 0x1d ch13 [15:8] ch_en13 setup_sel13 reserved ainpos13[4:3] 0x0001 rw [7:0] ainpos13[2:0] ainneg13 0x1e ch14 [15:8] ch_en14 setup_sel14 reserved ainpos14[4:3] 0x0001 rw [7:0] ainpos14[2:0] ainneg14 0x1f ch15 [15:8] ch_en15 setup_sel15 reserved ainpos15[4:3] 0x0001 rw [7:0] ainpos15[2:0] ainneg15
data sheet ad7175- 8 rev. 0 | page 59 of 64 setup configuration register 0 address: 0x20, reset: 0x1320, name: setupcon0 the setup configuration registers are 16 - bit registers that configure the reference selection, input buffers, and output coding of the adc. table 35 . bit descriptions for setupcon0 bits bit name settings description reset access [15:13] reserved these bits are reserved; set these bits to 0. 0x0 r 12 bi_unipolar0 this bit sets the output coding of the adc for setup 0. 0x1 rw 0 unipolar coded output 1 bipolar coded output (offset binary) 11 refbuf0+ this bit enables or disables the ref+ input buffer. 0x0 rw 0 ref+ buffer disabled 1 ref+ buffer enabled 10 refbuf0? this bit enables or disables the ref? input buffer. 0x0 rw 0 ref? buffer disabled 1 ref? buffer enabled 9 ainbuf0+ this bit enables or disables the ain+ input buffer. 0x1 rw 0 ain+ buffer disabled 1 ain+ buffer enabled 8 ainbuf0? this bit enables or disables the ain? input buffer. 0x1 rw 0 ain? buffer disabled 1 ain? buffer enabled 7 burnout_en0 this bit enables a 10 a current source on the positive analog input selected and a 10 a current sink on the negative analog input selected. the burnout currents are useful in diagnosis of an open wire, whereby the adc result goes to full scale. enabling the burnout currents during measurement results in an offset voltage on the adc. this means the strategy for d iagnosing an open wire operates best by turning on the burnout currents at intervals, before or after precision measurements. 0x00 r 6 reserved these bits are reserved; set these bits to 0. 0x00 r [5:4] ref_sel0 these bits allow the user to select the reference source for adc conversion on setup 0. 0x2 rw 00 external r eference. 01 external reference 2 supplied to ain1/ref2+ and ain0/ref2 ? pins. 10 internal 2.5 v r eference. this must also be enabled in the adc mode register. 11 avdd1 ? avss. this can be used to as a diagnostic to validate other reference values. [3:0] reserved these bits are reserved; set these bits to 0. 0x0 r
AD7175-8 data sheet rev. 0 | page 60 of 64 setup configuration register 1 to setup configuration register 7 address: 0x21 to 0x27, reset: 0x1320, name: setupcon1 to setupcon7 the remaining seven setup configuration registers share the same layout as setup configuration register 0. table 36. setupcon1 to setupcon7 register map reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x21 setupcon1 [15:8] reserved bi_unipolar1 re fbuf1+ refbuf1? ainbuf1+ ainbuf1? 0x1320 rw [7:0] burnout_en1 reserved ref_sel1 reserved 0x22 setupcon2 [15:8] reserved bi_unipolar2 re fbuf2+ refbuf2? ainbuf2+ ainbuf2? 0x1320 rw [7:0] burnout_en2 reserved ref_sel2 reserved 0x23 setupcon3 [15:8] reserved bi_unipolar3 re fbuf3+ refbuf3? ainbuf3+ ainbuf3? 0x1320 rw [7:0] burnout_en3 reserved ref_sel3 reserved 0x24 setupcon4 [15:8] reserved bi_unipolar4 re fbuf4+ refbuf4? ainbuf4+ ainbuf4? 0x1320 rw [7:0] burnout_en4 reserved ref_sel4 reserved 0x25 setupcon5 [15:8] reserved bi_unipolar5 re fbuf5+ refbuf5? ainbuf5+ ainbuf5? 0x1320 rw [7:0] burnout_en5 reserved ref_sel5 reserved 0x26 setupcon6 [15:8] reserved bi_unipolar6 re fbuf6+ refbuf6? ainbuf6+ ainbuf6? 0x1320 rw [7:0] burnout_en6 reserved ref_sel6 reserved 0x27 setupcon7 [15:8] reserved bi_unipolar7 re fbuf7+ refbuf7? ainbuf7+ ainbuf7? 0x1320 rw [7:0] burnout_en7 reserved ref_sel7 reserved
data sheet ad7175- 8 rev. 0 | page 61 of 64 filter configuration register 0 address: 0x28, reset: 0x0500, name: filtcon0 the filter configuration registers are 16 - bit registers that configure the adc data rate and filter options. writing to any of these registers resets any active adc conversion and restarts converting at the first channel in the sequence. table 37 . bit descriptions for filtcon0 bits bit name settings description reset access 15 sinc3_map0 if this bit is set, the mapping of the filter register changes to directly program the decimation rate of the sinc3 filter for setup 0. all other options are eliminated. this allows fine tuning of the output data rate and filter notch for rejection of specific frequencies. the data rate when on a sing le channel equals f mod /(32 filtcon0[14:0]). 0x0 rw [14:12] reserved these bits are reserved; set these bits to 0. 0x0 r 11 enhfilten0 this bit enables various postfilters for enhanced 50 hz/60 hz rejection for setup 0. the order0 bits must be set to 00 to select the sinc5 + sinc1 filter for this to work. 0x0 rw 0 disabled 1 enabled [10:8] enhfilt0 these bits select between various postfilters for enhanced 50 hz/60 hz rejection for setup 0. 0x5 rw 010 27 sps, 47 db rejection, 36.7 ms settling 011 25 sps, 62 db rejection, 40 ms settling 101 20 sps, 86 db rejection, 50 ms settling 110 16.67 sps, 92 db rejection, 60 ms settling 7 reserved this bit is reserved; set this bit to 0. 0x0 r [6:5] order0 these bits control the order of the digital filter that processes the modulator data for setup 0. 0x0 rw 00 sinc5 + sinc1 (default) 11 sinc3 [4:0] odr0 these bits control the output data rate of the adc and, therefore, the settling time and noise for setup 0. rates shown are for the sinc5 + sinc 1 filter. see table 19 to table 22. 0x0 rw 00000 250,000 00001 125,000 00010 62,500 00011 50,000 00100 31,250 00101 25,000 00110 15,625 00111 10,000 01000 5000 01001 2500 01010 1000 01011 500 01100 397.5 01101 200 01110 100 01111 59.92 10000 49.96 10001 20 10010 16.66 10011 10 10100 5
AD7175-8 data sheet rev. 0 | page 62 of 64 filter configuration register 1 to filter configuration register 7 address: 0x29 to 0x2f, reset: 0x0500, name: filtcon1 to filtcon7 the remaining seven filter configuration registers share the same layout as filter configuration register 0. table 38. filtcon1 to filtcon7 register map reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x29 filtcon1 [15:8] sinc3_map1 reserved enhfilten1 enhfilt1 0x0500 rw [7:0] reserved order1 odr1 0x2a filtcon2 [15:8] sinc3_map2 rese rved enhfilten2 enhfilt2 0x0500 rw [7:0] reserved order2 odr2 0x2b filtcon3 [15:8] sinc3_map3 rese rved enhfilten3 enhfilt3 0x0500 rw [7:0] reserved order3 odr3 0x2c filtcon4 [15:8] sinc3_map4 reserved enhfilten4 enhfilt4 0x0500 rw [7:0] reserved order4 odr4 0x2d filtcon5 [15:8] sinc3_map5 reserved enhfilten5 enhfilt5 0x0500 rw [7:0] reserved order5 odr5 0x2e filtcon6 [15:8] sinc3_map6 rese rved enhfilten6 enhfilt6 0x0500 rw [7:0] reserved order6 odr6 0x2f filtcon7 [15:8] sinc3_map7 reserved enhfilten7 enhfilt7 0x0500 rw [7:0] reserved order7 odr7 offset register 0 address: 0x30, reset: 0x800000, name: offset0 the offset (zero-scale) registers are 24-bit registers that can be used to compensate for any offset error in the adc or in the system. table 39. bit descriptions for offset0 bits bit name settings description reset access [23:0] offset0 offset calibration coefficient for setup 0. 0x800000 rw offset register 1 to offset register 7 address: 0x31 to 0x37, reset: 0x800000, name: offset1 to offset7 the remaining seven offset registers share the same layout as offset register 0. table 40. offset1 to offset7 register map reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x30 offset0 [23:0] offset0[23:0] 0x800000 rw 0x31 offset1 [23:0] offset1[23:0] 0x800000 rw 0x32 offset2 [23:0] offset2[23:0] 0x800000 rw 0x33 offset3 [23:0] offset3[23:0] 0x800000 rw 0x34 offset4 [23:0] offset4[23:0] 0x800000 rw 0x35 offset5 [23:0] offset5[23:0] 0x800000 rw 0x36 offset6 [23:0] offset6[23:0] 0x800000 rw 0x37 offset7 [23:0] offset7[23:0] 0x800000 rw gain register 0 address: 0x38, reset: 0x5xxxx0, name: gain0 the gain (full-scale) registers are 24-bit registers that can be used to compensate for any gain error in the adc or in the sys tem. table 41. bit descriptions for gain0 bits bit name settings description reset access [23:0] gain0 gain calibration coe fficient for setup 0. 0x5xxxx0 rw
data sheet AD7175-8 rev. 0 | page 63 of 64 gain register 1 to gain register 7 address: 0x39 to 0x3f, reset: 0x5xxxx0, name: gain1 to gain7 the remaining seven gain registers share the same layout as gain register 0. table 42. gain1 to gain7 register map reg. name bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset rw 0x38 gain0 [23:0] gain0[23:0] 0x5xxxx0 rw 0x39 gain1 [23:0] gain1[23:0] 0x5xxxx0 rw 0x3a gain2 [23:0] gain2[23:0] 0x5xxxx0 rw 0x3b gain3 [23:0] gain3[23:0] 0x5xxxx0 rw 0x3c gain4 [23:0] gain4[23:0] 0x5xxxx0 rw 0x3d gain5 [23:0] gain5[23:0] 0x5xxxx0 rw 0x3e gain6 [23:0] gain6[23:0] 0x5xxxx0 rw 0x3f gain7 [23:0] gain7[23:0] 0x5xxxx0 rw
ad7175- 8 data sheet rev. 0 | page 64 of 64 outline dimensions figure 72 . 40 - lead lead frame chip scale package [lfcsp_wq] 6 mm 6 mm body, very very thin quad (cp - 40 - 14) dimensions shown in millimeters ordering guide model 1 temperature range package description package option ad7175 - 8bcpz ? 40c to +105c 40 - lead lead frame chip scale package [lfcsp_wq] cp -40 -14 ad7175 - 8bcpz -rl ? 40c to +105c 40 - lead lead frame chip scale package [lfcsp_wq] cp -40 -14 ad7175 - 8bcpz -rl7 ? 40c to +105c 40 - lead lead frame chip scale package [lfcsp_wq] cp -40 -14 1 z = rohs compliant part. 0.50 bsc bot t om view top view pin 1 indic a t or exposed pa d pin 1 indic a t or sea ting plane 0.05 max 0.02 nom 0.20 ref coplanarity 0.08 0.30 0.25 0.18 6.10 6.00 sq 5.90 0.80 0.75 0.70 for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. 0.45 0.40 0.35 0.25 min 4.05 3.90 sq 3.75 compliant to jedec standards mo-220- wjjd . 40 1 11 20 21 30 31 10 05-06-20 1 1- a ? 2015 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their resp ective owners. d12911 - 0- 10/15(0)

▲Up To Search▲

Price & Availability of AD7175-8

	To Download AD7175-8 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .