View AMW006_8578407.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AMW006/amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me a m w 00 6 / amw106 data s heet
ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | i amwx06 ? embedded wi - fi networking solutions disclaimer while the information provided in this document is be- lieved to be accurate, it is under development and ackme networks reserves the right to make changes wi thout further notice to the product described herein to improve reliability, function, or design, and makes no guarantee or warranty concerning the accuracy of said information, nor shall it be responsible for any loss or damage of whatever nature resultin g from the use of, or reliance upon, such information. ackme networks makes no warranties of any kind, whether express, im- plied or arising by custom or course of trade or perfor- mance, and specifically disclaims the i mplied warranties of title, non - infringe ment, merchantability, or fitness for a particular purpose. no part of this document may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photographic, or otherwise, or used as the basis for manufacture or sale of any items without the prior written consent of ackme networks. trademarks ackme networks and the ackme networks logo are trademarks of ackme networks. other trademarks in this document belong to their respective owners . cop yright ? 201 4 - 2015 ackme networks. all rights reserved. document number: a ds - mx006 release date: september 1, 2015 contact http://ack.me/contact about this data s heet this document provide s information on the amw x 0 6 802.11b/g/n wi - fi networking module from ackme networks. s pecifications for the module i/o and peripherals are taken from mcu datasheet . specifica- tions for the wlan sub system were compiled from measured data unless otherwise n oted. organization this data sheet is organized into the following sections : ? features & applications ? general description, section 1 ? block diagram, section 2 ? electrical specifications, section 3 ? wlan rf specifications, section 4 ? pinout and signal descriptions, section 5 ? design guidelines, section 6 ? regulatory certification, section 7 ? packaging, handling & storage, rohs, section 8 ? ordering information, section 9 ? revision history & glossary , section 10 ? references, section 11
ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | ii a mw006 / amw106 data sheet embedded wi - fi networking solution features ? self - contained ultra - low power wi - fi module with microcontroller and secure tcp network stack . ? integrated spi - serial flash for software upgrades and user accessible read/write file system wi - fi ? broadcom single band 2.4ghz ieee 802.11b/g/n 1x1 wi - fi transceiver ? includes support for all wi - fi security modes includ- ing open, wep, wpa, and wpa2 - psk microprocessor ? arm cortex ? m4 based microprocessor ? AMW006: operat es up to 84mhz core frequency ? amw106: operates up to 100mhz core frequency ram ? AMW006: 96 kb ? amw106: 128 kb interfaces * ? uart : 2 x 4 - wire up to 10.5mbit/s ? spi : spi - master (42mbit/s), spi - slave (21 mbit/s ) ? gpio: up to 21 gpios ( overlaid with peripherals) ? a/d converter : 9 channel input , 12 - bit resolution, 2.4msps sampling in single - shot or scan mode ? pwm : up to 14 pwm outputs ? wake - up : w ake pin for ultra - low power operation ? two e xternal antenna s for diversity and improved range * some interfaces share module pins operational & radio ? single operating voltage : 3.3v (typical) ? all i/o pins are +5v tolerant ? operational temperature range: - 3 0 c to + 85 c ? size : 2 0 . 3 x 15.2 x 2 . 7 mm (0. 8 0 x 0. 6 0 x 0. 1 1 ) ? weight : 0.07 oz (2g) ? current consumption @ 3.3v, 25c - vbat : 0.97 a (with 32k rtc) - standby : 2 .8 a (3. 8 ua with 32k rtc ) - stop : 10 a with ram retention ( 113 s wake) - wi - fi powersave : 0.77m a (dtim = 3) - active receive : 5.7 ma @ 1mbit/s udp ? active transmit : 1 1 . 4 ma @ 1mbit/s udp ? maximum rf transmit power - 802.11b /g : + 1 8 dbm - 802.11n : + 1 4 dbm ? minimum receive sensitivity - 802.11b /g : - 94 dbm - 802.11n : - 86 dbm ? sustained tcp throughput : 10 mbit/s applications ? industrial , m2m and home automation - environmental monitoring - energy monitoring - wireless sensing , remote data logging - hvac, power, light, & thermostat control - appliance control ? security - cameras, doors / window monitoring - alarms , smoke detectors - door and entry control ? health & fitness - fitness equipment - home health monitoring e . g. w eight s cales ? consumer - audio, toys , robots
AMW006 / amw106 ? emb edded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | iii contents 1 general description ................................ ............... 1 2 block diagram ................................ ........................ 2 3 electrical specifications ................................ .......... 3 3.1 absolute maximum ratings ............................ 3 3.2 recommended operating conditions ............ 3 dc operating conditions ........................ 3 environmental conditions ...................... 4 3.3 power consumption ................................ ....... 4 3.4 32kh z crystal ................................ .................. 5 4 wlan rf specifications ................................ ......... 6 4.1 summary wlan specifications ....................... 6 4.2 wlan receiver specifications ........................ 6 4.3 wlan transmitter specifications ................... 7 5 pinout and signal descriptions .............................. 8 5.1 pinout ................................ .............................. 8 5.2 pin description ................................ ................ 8 6 design guidelines ................................ ................. 10 6.1 recommended pcb footprint ...................... 10 6.2 routing recommendations .......................... 11 6.3 soldering information ................................ ... 12 6.4 module photograph ................................ ...... 13 6.5 ex ternal antennas ................................ ......... 13 pcb trace antenna ............................... 13 wire antenna ................................ ........ 13 chip antenna ................................ ........ 14 monopole antenna ............................... 14 6.6 application examples ................................ .... 15 operation using wiconnect ................. 15 7 regulatory certification ................................ ....... 16 7.1 united states ................................ ................ 16 labeling and user information requirements ................................ ....................... 16 rf exposure ................................ .......... 17 approved external antenna types ....... 17 further information .............................. 17 7.2 canada ................................ .......................... 17 labeling and user information requirements ................................ ....................... 17 external antenna types ........................ 19 further information .............................. 19 7.3 europe ................................ .......................... 19 labeling and user information requirements ................................ ....................... 19 external antenna requirements .......... 19 further information .............................. 20 7.4 australia ................................ ........................ 20 external antenna requirements .......... 20 further information .............................. 20 7.5 new zealand ................................ ................. 21 external antenna requirements .......... 21 further information .............................. 21 7.6 japan ................................ ............................. 21 8 packaging, handl ing and storage, rohs .............. 22 8.1 packaging ................................ ...................... 22 8.2 handling & storage ................................ ....... 22 8.3 ro hs directive ................................ .............. 22 8.4 tape and reel specifications ........................ 23 9 ordering information ................................ ........... 25 10 rev ision history & glossary ................................ . 26 10.1 revision history ................................ ............ 26 10.2 glossary ................................ ........................ 26 11 references ................................ ........................... 27
general description , section 1 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 1 1 general descripti on the a mw006 and amw106 module s from ackme net- works com bine a microcontroller with a bcm43362 wi - fi device to provide a n advanced stand - alone wi - fi and networking solution. t he term amwx06 refers to both modules. an integrated module avoids difficult rf layout and e na- bles designers to rapidly embe d wi - fi and secure net- working functionality into virtually any device . the ackme networks wiconnect serial - to - wi - fi applica- tion , pre - programmed into all modules, may be used to fast - track module integration into end - products . with dimensions of just 2 0 . 3 mm x 15 . 2 mm and a wide temperature range, the module is suitable for integra- tion into most embedded applications. the wi - fi device from broadcom includes an integrated rf transmit power amplifier and provides superior wi - fi performance and full compatibility with all 2.4ghz 802.11b/g/n wi - fi networks. connections for two exter- nal antenna s provide applications with maximum radio range and mechanical design flexibility . the microprocessor is based on a high - performance arm? 32 - bit cortex? - m 4 . the AMW006/amw106 microcontroller core operat es at a frequency up to 84/ 100mhz providing up to 1 2 5 dmips or 1.25 dmips/mhz (dhrystone 2.1) . the AMW006 has 96kb of ram. the amw106 has 128kb of ram. the a mw x 06 mod ule offers extensive i/o and periph- eral interfaces listed below , and provides additional interface combinations by leveraging multiplexing and alternate function capabilities. ? 2 x 4 - wire uart interfaces ? 2 x spi interfaces (1 master, 1 slave) ? 2 1 x gpios ? 9 x 12 - bit a/d converters ? 14 x pwm outputs ? 1 x ultra - low power wake input the module is powered by a 3.3v power supply , a sepa- rate wlan power supply pin is provided to minimize noise coupling into the wlan subsystem. various powersave modes offer ultra - low power opera- tion . wake from low power sleep mode is possible using io pins or the internal real - time clock, and wake from ul- tra - low power standby mode is achieved using the dedi- cated wake pin . the module incorporates a 32 .768 khz crystal to main- tain an accurate real time clock . a 32khz clock output is available on a dedicated module pin in both active power save modes . the 32khz clock output may be used to drive the clock input of other system devices. this a voids the need for an additional crystal there by minimizing to- tal system cost. the module has fcc & ic modular approval for use in the united states and canada , ce approval for use in europe , telec/ mic approval for use in japan and related approv- als for use in other countries.
block diagram , section 2 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 2 2 block diagram figure 1 is a block diagram of the a mw x 06 module. the main components of the module are a microprocessor and bcm43362 wi - fi system - on - chip (soc) . the proces- sor and peripherals are driven by a 26 mhz crystal . t he integrated real - time clock ( rtc ) is driven by a 32 .768 khz crystal . an on - board 1mbyte serial flash chip may be used to store user data and configuration, additional ap- plications, and firmware images as part o f the ackme se- cure over the air (ota) update process . t he wlan sub system is controlled by wiconnect ena- bling the module to achieve minimum power consump- tion when the wi - fi networking interface is not required. the module includes an antenna diversity switch. the switch enables static or dynamic control of the external antenna ( s ) . figure 1 . a mw006 / amw106 architecture antenna switch vbat 3v3 mcu 3v3 wi - fi 32khz out adc pwm uart spi gpio reset arm cortex m4 bcm43362 wi - fi 26mhz 32khz 1 mbyte serial flash AMW006 / amw106 antenna 1 antenna 2
electrical specifications , section 3 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 3 3 electrical specifications 3.1 absolute maximum rating s caution ! the absolute maximum ratings in table 1 and table 2 indicate levels where p ermanent damage to the device can occur, even if these limits are exceeded for only a brief duration. functional operation is not guaranteed under these condi tions. operation at absolute maximum conditions fo r extended periods can adversel y affect long - ter m re- liability of the device. the values in table 1 reflect absolute maximum ratings from the respective microprocessor and bcm43362 datasheets. table 1 . absolute maximum voltage ratings symbol ratings min max unit vbat external power supply voltage to mcu vbat pin - 0.3 4.0 v vdd_3v3 external power supply voltage to mcu subsystem - 0.3 4.0 vdd_wifi external power supply voltage to wlan subsystem - 0.5 6.0 v in input voltage on any other mcu pin gnd - 0.3 vdd_3v3 + 4.0 table 2 . absolute maximum environmental ratings characteristic note min max unit storage temperature C - 40 + 125 c relative humidity non - condensing (storage) C 6 5 % 3.2 recommended operating conditions functional operation is not guaranteed outside the limits shown in table 3 and table 4 , and operation outside these limits for extended periods can adversely affect long - term r eliability of the device. dc operating conditions table 3 . recommended dc operating conditions symbol ratings min typ max unit vbat external power supply voltage to mcu vbat pin 3.0 3.3 3.6 v vdd_3v3 1 external power supply voltage to mcu subsystem 3.0 3.3 3.6 vdd_wifi 1,2 external power supply voltage to wlan subsystem 3 . 0 3.3 3.6 note s : 1. vdd_3v3 and vdd_wifi must be at the same voltage when using the wi - fi subsystem 2. the performance of the wi - fi subsystem is degraded significantly at low voltages
electrical specifications , section 3 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 4 environmental conditions table 4 . recommended environmental conditions characteristic note min max unit ambient temperature limited by wlan chip specification - 30 +85 c relative humidity non - condensing (operating) C 85 % 3.3 power consumption table 5 . power consumption (vdd_3v3, vdd_wifi , vbat @ 3.3v) operational state note typ 1 max 1 max 1 unit t a = 25 c t a = 85 c vbat 7 m c u vbat mode, rtc on, wi - fi powered off 0.97 C 3.0 a standby 7 m c u standby mode, rtc on, wi - fi powered off 3 . 8 5 .0 1 7 .0 a stop 3 , 7 mcu stop mode, wi - fi powered off 10 28 230 a wi - fi powersave 2,3 mcu stop mode, wi - fi in powersave 0.77 C C ma active receive 2,3,4 mcu stop mode, wi - fi active receive 5.7 C C ma active transmit 2,3,5 mcu stop mode, wi - fi active transmit 11.4 C C ma wi - fi tx test mode 6 mcu stop mode, wi - fi active transmit C 320 C ma note s : 1. total combined current consumed by all power supplies: vbat, vdd_3v3, vdd_wifi . 2. 802.11 beacon interval = 102.4ms, dtim=3, beacon duration = 1ms @ 1mbps. 3. mcu stop mode with 113 s wakeup latency (flash in deep power down mode) , vdd_wifi = 0v 4. average current receiving 1mbit/s udp at 802.11n mcs7 5. average current t ransmitting 1mbit/s udp at 802.11n mcs7 6. wi - fi transmitting at + 1 8 dbm cck 11mbit/s with maximum duty cycle 7. hardware capability; minimum power consumption is dependent on wiconnect version and external compo- nents connected to amw x 06 pins
electrical specifications , section 3 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 5 3.4 32khz crystal table 6 . 32khz crystal specifications 1 operational state note min typical max unit frequency C 32768 C hz frequency tolerance C 20 C ppm frequency ageing measured @25 c 3 c - 3 C +3 ppm note s : 1. reproduced from manufacturers datasheet.
wlan rf specifications , section 4 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 6 4 wlan rf specifications the a mw x 06 wlan radio specifications are derived from the broadcom bcm43362 wlan radio specifications. unless otherwise stated, the specifications in this section apply when the operating conditions are within the limits specified in section 3.2 , recommended operating conditions . functional operation outside these limits is not guaran- teed. all specification s are measured by connecting directly to either of the antenna ports via a short pcb trace with the other antenna port terminated in 50 ohms . 4.1 summary wlan specifications tabl e 7 . summary wlan specifications feature supported description wlan standard ieee 802.11b/g/n 1x1 siso frequency band 2.400 ghz C 2.484 ghz wlan channels channels 1 C 13 data rates 802.11b ( 1, 2, 5.5, 11 mbps) 802.11g ( 6, 9, 12, 24, 36, 48, 54 mb ps) 802.11n ( ht20 mcs0 - mcs 7 ) maximum receive level @ 2.4ghz - 2.5 dbm @ 1, 2 mbps (8% per, 1024 octets) - 8.5 dbm @ 5.5, 11 mbps (8% per, 1024 octets) - 12 dbm @ 6 - 54 mbps (10% per, 1000 octets) maximum rf tx output power + 1 8 dbm @ 802.11b (evm < - 9 db) + 1 4 dbm @ 802.11n mcs7 (evm < - 28 db) carrier frequency accuracy 20 ppm (26mhz crystal with 10 ppm @ 25c) 4.2 wlan receiver specifications table 8 . wlan receiver performance specifications parameter condition/notes min typ ical max unit frequency range C 2400 C 2500 mhz operating temperature 1 C - 30 C + 85 c receive sensitivity 2 (8% per for 1024 octet psdu) at either antenna port 3 1 mbps dsss C - 94 - 91 dbm 11 mbps cck C - 87 - 83 receive sensitivity 2 (10% per for 1000 octet psdu) at either antenna port 3 6 mbps ofdm C - 86 - 81 dbm 54 mbps ofdm C - 73 - 69
wlan rf specifications , section 4 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 7 parameter condition/notes min typ ical max unit receive sensitivity 2 (10% per for 4096 octet psdu) at either antenna port 3 . defined for default parame- ters: gf, 800ns gi, and non - stbc 65 mbps mcs0, ht20 C - 86 - 81 dbm 65 mbps mcs7, ht20 C - 70 - 65 max. receive level @ 2.4ghz @ 1, 2 mbps (8% per, 1024 octets) - 2 C C dbm @ 5.5, 11 mbps (8% per, 1024 octets) - 8 C C @ 6 - 54 mbps (10% per, 1000 octets) - 11.5 C C notes : 1. operation below - 20 c and above +65 c with parameter derating per note 2 2. d erate receive sensitivity by 1.5db for operation between temperatures of - 30c to - 2 0c and 6 5c to 85c 3. all measurements performed with the other antenna port terminated in 50 ohms 4.3 wlan tran smitter specifications table 9 . wlan transmitter performance specifications parameter condition/notes min typ ical max unit frequency range C 2400 C 2500 mhz operating temperature 1 C - 30 C + 85 c transmit power 2 measured at either antenna port 3 for high- est power level setting at 25c, vdd - 3v3_rf_in=3.3v with spectral mask and evm compliance evm does not exceed : 1 mbps dsss - 11 db + 1 4 + 1 6 + 1 8 dbm 11 mbps cck - 11 db + 1 4 + 1 6 + 1 8 6 mbps ofdm - 22 db + 12 + 14 + 16 54 mbps ofdm - 25 db + 12 + 14 + 16 mcs0, ht20 - 22 db + 1 0 + 1 2 + 1 4 mcs7, ht20 - 28 db + 1 0 + 1 2 + 1 4 notes : 1. operation below - 20 c and above +65 c with parameter derating per note 2 2. derate transmit power by 1.5db for operation between temperatures of - 30c to - 2 0c and 6 5c to 85c 3. all measurements performed with the other antenna port terminated in 50 ohms
pinout and signal descriptions , section 5 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 8 5 pin out and signal descriptions 5.1 pinout a top view of the a mw x 06 pinout is depicted in figure 2 . all dimensions are in thousands of an inch. a recom- mended footprint is provided in section 6.1 . figure 2 . a mw x 06 pinout (top v iew C pins not visible from top!) 5.2 pin description table 10 . a mw x 06 wiconnect pin definitions pin name type 1 primary function alternate & other function(s) 1 - 2 gnd s ground - 3 vbat s vbat mcu supply - 4 gpio_0 i/o factory reset 2 spi1 _miso ( s ) , gpio 5 gpio_1 i/o gpio - 6 gpio_2 i/o gpio spi1 _sck ( s ) 7 gpio_3 i/o gpio spi1 _cs ( s ) 8 gpio_4 i/o gpio - 9 osc_32k_out o osc_32k_out - 10 vdd_3v3 i/o 3.3v mcu supply 11 - 12 gnd s ground - 13 gpio_5 i/o gpio spi1 _mosi (slave) , pwm 5
pinout and signal descriptions , section 5 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 9 pin name type 1 primary function alternate & other function(s) 14 gpio_6 i/o spi 0 _miso (m) 5 adc 6 (when spi not in use). not available for digital i/o. 15 gpio_7 i/o spi0 _sck (m) 5 adc 5 (when spi not in use). not available for digital i/o. 16 gpio_8 i/o spi0 _mosi (m) 5 adc 7 (when spi not in use). not available for digital i/o. 17 gpio_9 i/o gpio uart 0 _rts 18 gpio_10 i/o gpio uart0_cts , pwm 0 19 gpio_11 i/o uart0_rx gpio , pwm 0 20 gpio_12 i/o uart0_tx gpio , pwm 0 21 gpio_13 i/o gpio pwm 1 22 gpio_14 i/o gpio pwm 3 23 gpio_15 i/o gpio pwm 3 24 gpio_16 i/o gpio pwm 6 25 gpio_17 i/o gpio uart1_rx, adc 3 , pwm 4 26 - 27 gnd i/o ground - 28 gpio_18 i/o gpio - 29 gpio_19 i/o gpio uart1_tx, adc 2 , pwm 4 30 gpio_20 i/o gpio adc 9 , pwm 2 31 gpio_21 i/o gpio adc 8 , pwm 2 32 gpio_22 i/o gpio uart1_cts, wake , adc 0 , pwm 1 33 gpio_23 i/o gpio uart1_rts, adc 1 , pwm 4 34 reset_n i system reset 4 35 vdd_wifi s 3.3v wlan supply - 36 - 42 gnd s ground - 43 antenna_1 o wi - fi antenna 3 - 44 - 46 gnd s ground - 47 antenna_2 o wi - fi antenna 3 - 48 - 52 gnd s ground - notes : 1. i = input , o = output , s = supply 2. factory reset is sampled at power - on - reset and available for other purposes thereafter. 3. wi - fi antenna pins are ac - coupled and have a nominal 50 ohms output impedance.
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 10 4. the module reset pin is connected to the internal mcu via a 1k resistor. we recommend driving the pin . if the pin is not driven, connect a 0.1uf cap acitor to ground close to the pin to bypass nois e which may cause unintended reset. 5. connected to spi serial flash inside the module. 6 design guidelines 6.1 recommended pcb footprint all dimensions in figure 3 are in th ousands of an inch unless otherwise marked. figure 3 . a mw x 06 recommended footprint (top)
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 11 6.2 routing recommendations when designing a carrier board, the addition of ground fill directly underneath the a mw x 06 module, rather than signal or power traces, is recommended. if traces must be routed directly beneath the module, avoid routing directly under- neath keepout areas shown in figure 4 (ground fill is ok) . all ground pads adjacent to antenna pins must be connected to a solid ground plane. failure to comply with these recommendations may result in degraded performance of wlan functionality. figure 4 . amw x 06 keepouts (top view)
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 12 6.3 solder ing information figure 5 - recommended solder reflow profile figure 6 - example solder reflow profile (amw0 06 - e0 3 evaluation board)
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 13 6.4 module photograph figure 7 . AMW006 photograph (top) 6.5 external antenna s the amw x 06 module supports two external antennas and per - packet antenna diversity to achieve maximum range. antenna selection is available by setting wicon- nect variables. note! both antenna ports must be terminated in 50 ohms. if a single antenna is used, the other antenna port should be terminated with a 50 ohm load. failure to ter- minate both antenna ports may result in degraded radio performa nce. table 11 - tested external antenna types model type 1 gain (dbi) printed antenna pcb trace 3.2 wire monopole 2.1 johanson tech. 2450at42a100e chip 0.0 aca - 1srpp - 2400 monopole 0. 6 aca - 4hsrpp - 2458 monopole 1.0 ( 1 ) an antenna type comprises antennas having similar in - band and out - of - band radiation patterns. pcb trace antenna this 2.4 ghz pcb antenna can fit in an area smaller than 2 1mm x 10 mm , and as small as 15mm x 6mm . to achieve optimum performance, make an exac t copy of this refer- ence design. figure 8 - trace antenna (dimensions in mm) wire antenna a s uitable wire antenna is an 18 - gauge wire with a length of 25.4mm 2mm . t he wire antenna s should be perpen- dicular to each other, and at 45 degre e s to the line be- tween the antenna bases . note! do not bend antennas backwards over the mod- ule; doing so will cause poor performance and may cause undesirable out - of - band radio transmissions. figure 9 - AMW006 - e03 eval board with wire antennas
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 14 chip antenna the amw x 06 is cer tified for use with a chip antenna from johanson, part number 2450at42a100e . be sure to follow the antenna layout design guidelines in the an- tenna datasheet. figure 10 C chip antenna layout example monopole antenna a u .fl connector layout such as the one shown below can be used to connect the whip antenna (s) . figure 11 - u .fl connector layout suitable monopole antennas include the aca_1ssrpp_2400 and aca_4hsrpp_2458 , both of which are available online at http://ack.me . figure 12 - aca - 1ssrpp - 2400 figure 13 - aca - 4hsrpp - 2458
design guidelines , section 6 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 15 6.6 application examples tbd operation using wiconnect t o use ackmes easy - to - use wiconnect serial - to - wi - fi application, the m odule only requires an external con- nection to power and a uart serial interface. a host processor connects to uart 0 ( pins 19 / 20 ) or uart 1 (pins 2 5 /2 9 ) as shown in figure 14 . figure 14 . using the a mw006 module with wiconnect and a uart serial interface
regulato ry certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 16 7 regulatory certification the AMW006 module has been certified for operation in various regulatory domains. this section outlines certifi- cation information specific to the following countries and regions: ? united states ? canada ? europe ? australia ? new zealand ? japan should you require regulatory certification for the AMW006 module in a country or region not listed, please contact your local ackme networks sales office or create a support request via our website at http://ack.me /contact . 7.1 united states the ackme networks AMW006 module has received federal communications commission (fcc) cfr47 tele- communications, part 15 sub - part c intentional radia- tors modular approval in accordance with part 15.212 modular transmitter approval. modular approval allows the end user to integrate the AMW006 module into a fin- ished product without obtaining subsequent and sepa- rate fcc approvals for intentional radiation, provided no changes or modifications are made to the module cir- cuitry. changes or modific ations could void the users au- thority to operate the equipment. the end user must comply with all of the instructions provided by the grantee which indicate installation and/or operating conditions necessary for compliance. the finished product is require d to comply with all appli- cable fcc equipment authorization, regulations, require- ments, and equipment functions not associated with the transmitter module portion. for example, compliance must be demonstrated to regulations for other transmit- ter components within the host product; to require- ments for unintentional radiators (part 15 sub - part b unintentional radiators), such as digital devices, com- puter peripherals, radio receivers, etc.; and to additional authorization requirements for non - transmitter fun c- tions on the transmitter module (i.e. verification, or dec- laration of conformity) (e.g., transmitter modules may also contain digital logic functions) as appropriate. labeling and user information requirements the AMW006 module has been labelled with a u nique fcc id number, and if the fcc id is not visible when the module is installed inside another device, then the out- side of the finished product into which the module is in- stalled must also display a label referring to the enclosed module. this exterior label can use wording as follows: the user manual for the product should include the fol- lowing statement: contains fcc id: 2abpy - b5bd9 this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause unde- sired operation. this equipment has been tested and found to com - ply with the limits for a class b digital devi ce, pursu- ant to part 15 of the fcc rules. these limits are de- signed to provide reasonable protection against harmful interference in a residential installation. this equipment generates, uses and can radiate radio fre- quency energy and if not installed and used in ac- cordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful i nterference to radio or television re- ception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfe rence by one or more of the fol- l owing measures: ? reorient or relocate the receiving antenna. ? increase the separation between the equip- ment and receiver. ? connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected. ? consult the dealer or an experienced radio/tv technician for help.
regulatory certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 17 additional informatio n on labeling and user information requirements for part 15 devices can be found in kdb publication 784748 available at the fcc office of engi- neering and technology (oet) laboratory division knowledge database (kdb) at the following website: https://apps.fcc.gov/oetcf/kdb/index.cfm rf exposure all transmitters regulated by fcc must comply with rf exposure requirements. oet bulletin 65, evaluating compliance with fcc guidelines for human exposure to ra dio frequency electromagnetic fields, provides assis- tance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to radio frequency (rf) fields adopted by the federal communications commission (fcc). the bulletin offers guidelines and suggestions for evaluating compliance. if appropriate, compliance with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels and by providing users with i n- formation concerning minimum separation distances from transmitting structures and proper installation of antennas. the following statement must be included as a caution statement in manuals and oem products to alert users of fcc rf exposure compliance: if the AMW006 module is used in a portable application (i.e., the antenna is le ss than 20 cm from persons during operation), the integrator is responsible for performing specific absorption rate (sar) testing in accordance with fcc rules 2.1091. approved external antenna types modular approval testing of the AMW006 was per- formed with the antenna types listed in table 11 - tested external antenna types . to maintain modular approval in the united states, only the tested antenna types shall be used. it is permissible to use different antenna manufacturers provided the an- tenna types match: in - band and out - of - band radiation patterns and antenna gain must be similar to those tested. further information additional information regarding fcc certification and use of the AMW006 module in the united states is avail- able from the following sources. ? federal communications commission (fcc) http://www.fcc.gov.au ? fcc office of engineering and technology (oet) la- boratory division knowledge database (kdb) http://apps.fcc.gov/oetcf/kdb/index.cfm 7.2 canada the AMW006 module has been certified for use in can- ada under industry canada (ic) radio standards specifi- cation (rss) r ss - 210 and rssgen. modular approval per- mits the installation of a module in a host device without the need to recertify the device. labeling and user information requirements labeling requirements for the host device (from section 3.2.1, rss - gen, issue 3, december 2010): the host de- vice shall be properly labeled to identify the module within the host device. the industry canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to dis- play the industry canada certification number of the module, preceded by the words contains transmitter module, or the word contains, or similar wording ex- pressing the same meaning, as follows: to satisfy fcc rf exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained be- tween the antenna of this device and persons dur- ing operation. to ensure compliance, operation at closer than this distance is not recommended. the antenna(s) used for this transmitter must not b e co - located or operating in conjunction with any other antenna or transmitter contains transmitter module ic: 11685a - 61f8d
regulatory certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 18 user manual notice for license - exempt radio apparatus (from section 7.1.3 rss - gen, issue 3, december 2010): user manuals for license - exempt radio apparatus shall contain the following or equivalent notice in a conspicu- ous location in the use r manual or alternatively on the device or both: transmitter antenna notification (f rom section 7.1.2 rss - gen, issue 3, december 2010): user manuals for transmitters shall display the following notice in a con- spicuous location: the above notice may be affixed to the device instead of displayed in the user manual. user manuals for transmitters equipped with detach - able antennas shall also contain the following notice in a conspicuous location: this device complies with industry canada license - exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'industrie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux onditions suiv antes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appa- reil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible d'en com- promettre le fonctionnement. under industry canada regulations, this radio trans- mitter may only operate using an antenna of a type and max imum (or lesser) gain approved for the trans- mitter by industry canada. to reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotrop- ically radiated power ( eirp ) is not more t han that ne cessary for successful communication. conformment la rglementation d'industrie can - ada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inf- rieur) approuv pour l'metteur par industrie can- ada. dans le but de rduire les risques de brouil - lage radiolectrique l'intention des autres utilisa - teurs, il faut choisir le type d'antenne et son gain de sorte que la pui ssance isotrope rayonne quiva lente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tabli ssement d'une communication satisfaisante. this radio transmitter (identify the device by certifi- cation number, or model number if category ii) has been approved by industry canada to operate with the antenna types listed below with the maximum permissible gain and required antenna imp edance for each antenna type indicated. antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie i) a t approuv par industrie canada pour fonctionner avec les types d'antenne numrs ci - dessous et ayant un gain admissible maximal et l'impdance requise p our chaque type d'antenne. les types d'an- tenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur.
regulatory certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 19 immediately following the above notice, the manufac- turer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dbi) and required imped- ance for each. external antenna types modular approval testing of the AMW006 was per- formed with the anten na types listed in table 11 - tested external antenna types . transmitter antenna (from section 7.1.2 rss - gen, issue 3, december 2010): the AMW006 module can only be so ld or operated with antennas with which it was approved. transmitter may be approved with multiple antenna types. an antenna type comprises antennas having similar in - band and out - of - band radiation patterns. testing shall be performed using the highest gai n antenna of each combination of transmitter and antenna type for which approval is being sought, with the transmitter output power set at the maximum level. any antenna of the same type having equal or lesser gain as an antenna that had been success- fully tested with the transmitter, will also be considered approved with the transmitter, and may be used and marketed with the transmitter. when a measurement at the antenna connector is used to determine rf output power, the effective gain of the device's ant enna shall be stated, based on measurement or on data from the antenna manufacturer. for transmitters of output power greater than 10 milli- watts, the total antenna gain shall be added to the meas- ured rf output power to demonstrate compliance to the specifi ed radiated power limits. further information additional information may be obtained from the indus- try canada website at http://www.ic.gc.ca 7.3 europe the AMW006 module is an r&tte directive assessed ra- dio module that is ce marked and has been manufac- tured and tested with the intention of being integrated into a final product. the AMW006 module has been tested to r&tte direc- tive s as summarized in table 12 . european compliance testing . opinion has also been issued. all AMW006 test reports are available on the ackme networks website at http://ack.me /contact . the r&tte compliance association provides guidance on modular devices in the document titled technical guidance note 01 available on the website at http://www.rtteca.com/html/download_area.htm . labeling and user information requirements the label on the final product which contains the AMW006 module must follow ce marking requirements. the r&tte compliance association technical guidance note 01 provides guidance on final product ce marking external antenna requirements from r&tte compliance association document tech- nical guidance note 01: provided the integrator installing an assessed radio mod- ule with an integral or specific ant enna and installed in conformance with the radio module manufacturers in- stallation instructions requires no further evaluation un- der article 3.2 of the r&tte directive and does not re- quire further involvement of an r&tte directive notified body for the fi nal product. [ section 2.2.4 ] the european compliance testing listed in table 12 . eu- ropean compliance testing was performed using an- tenna types listed in table 11 - tested external antenna types . note : to maintain conformance to the testing listed in table 12 . european compliance testing , the mod- ule shall be installed in accordance with the installa- tio n instructions in this data sheet and shall not be modified. when integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final produc t with the essential requirements of the r&tte directive.
regulatory certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 20 further information a document that can be used as a starting point in un- derstanding the use of short range devices (srd) in eu- rope is the european radio communications committee (erc) recommendation 70 - 03 e, which can be down- loaded from the european radio communications office (ero) at: http://www.ero.dk . further information may be obtained from the follow ing websites: ? radio and telecommunications terminal equip- ment (r&tte) http://ec.europa.eu/enterprise/rtte/index_en.htm ? european conference of postal and telecommuni- cations administrations (ce pt) http://www.cept.org ? european telecommunications standards institute (etsi) http://www.etsi.org ? european radio communications office (ero) http://w ww.ero.dk ? the radio and telecommunications terminal equipment compliance association (r&tte ca) http://www.rtteca.com/ table 12 . european compliance testing certification standard report number date laboratory safety en 60950 - 1:2006, a11:2009, a1:2010, a12:2011, a2:2013 w6m21410 - 14584 - l jan 15, 2015 worldwide testing services (taiwan) co., ltd. emf en 62311:2008 ea560122 jul 1, 2015 sporton international, inc . (taiwan) emc en 301 489 - 1 v1. 9.2 (20 11 - 0 9 ) , class b en 301 489 - 17 v2. 2 .1 (20 12 - 0 9 ) en 55022:2010/ac:2011 , class b en 55024:2010 eh560122 jul 1, 2015 radio en 300 328 v1. 9 .1 (20 15 - 02 ) er560122 jul 1, 2015 notified body opinion 1177 tcf - 1334tc15 jul 5 , 2015 timco engineering, inc. 7.4 australia australian radio regulations do not provide a modular approval policy similar to the united states (fcc) and canada (ic). however, AMW006 module test reports may be used in part to demonstrate compliance in ac- cordance with acma radio communications short range devices standard 2004 which references aus- tralia/new zealand industry standard as/nzs - 4268:2012. AMW006 rf transmitter test reports may be used as part of the product certification and compliance folder. for further information regarding the availability of rf test reports, please contact ackme networks via our website at http://ack.me /contact . external antenna requirements compliance tests were performed using antenna types listed in table 11 - tested external antenna types . if an external antenna is used with the AMW006 module, additio nal testing of the end product is needed to meet australian regulatory requirements. further information additional information may be obtained from the aus- tralian communications and media authority website at http://www.acma.gov.au .
regulatory certification , section 7 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 21 7.5 new zealand new zealand radio regulations do not provide a modular approval policy similar to the united states (fcc) and canada (ic). however, AMW006 module test reports may be used in part to demonstrate compliance with the new z ealand general user radio license for short range devices. new zealand radio communications (radio standards) notice 2010 references australia/new zealand industry standard as/nzs - 4268:2012. AMW006 rf transmitter test reports may be used as part of the p roduct certification and compliance folder. for further information regarding the availability of rf test reports, please contact ackme networks via our website at http://ack.me /contact . external antenna requirements compliance tests were performed using antenna types listed in table 11 - tested external antenna types . if an external antenna is used with the AMW006 module, additio nal testing of the end product is needed to meet new zealand regulatory requirements. further information additional information may be obtained from the new zealand radio spectrum ministry of economic develop- ment website at http://www.rsm.govt.nz . 7.6 japan the AMW006 has been tested to comply with the radio regulations set forth by the japanese ministry of internal affairs and communications (mic) as documented in ta- ble 13 . the module is certified for operation with each of the antenna types listed in table 11 - tested external an- tenna types . table 13 . japan compliance testing certification standard report number date laboratory verification of compliance vcci v - 3/2014.04 class b ite jv560122 jul 1, 2015 sporton international, inc . (taiwan) radio notice no. 88 appendix no. 43 jrf560122 jul 1, 2015 equipment marking 152150256/aa/00 jul 6, 2015 telefication, bv. (the netherlands)
packaging, handling and storage, rohs , section 8 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 22 8 packaging, handling and storage, rohs 8.1 packaging each amw x 06/s module is in dividually packaged in an esd bag. the bag is not compliant with msl3, and ac- cordingly amw x 06/s modules should not be passed through a reflow oven. amw x 06/s modules should be hand - soldered only! if reflow is required, amw x 06/s must be baked first ac- cording to joint industry s tandard j - std - 033c. amw x 06 / r module s are shipped in a reel enclosed in- side a moisture resistant sealed bag. the shelf life of the sealed reel is 12 months at 40c and <90% relative hu- midity (rh). please refer to the bag seal date and the fol- lowing section for handling & storage . 8.2 handling & storage caution msl3 sensitive device! the amw00 6 module is a moisture sensitive device rated at moisture sensitive level 3 (msl3) per ipc/jedec j - std - 20 . after opening the moisture sealed storage bag, modules that will be subjected to reflow solder or other high tem- perature processes must be: 1. mounted to a circuit board within 168 hours at factory conditions (30c and <60% rh) or 2. continuously stored per ipc/jedec j - std - 033 modules that have been exposed to moisture and envi- ronmental conditions exceeding packaging and storage conditions must be baked before mounting according to ipc/jedec j - std - 033 . failure to meet packaging and storage conditions will re- sult in irreparable damage to modules during solder re- flow. 8.3 roh s directive the amw x 06 module is produced according to the rohs (restriction of the use of certain hazardous substances in electrical and electronic equipment) directive and complies with the directive.
packaging, handling and storage, rohs , section 8 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 23 8.4 tape and reel specifications figure 15 - tape specifications symbol a0 b0 d0 e f k0 specification (mm) 11.8 0.10 18.1 0.10 1.5 0.10 1.75 0.10 14.2 0.10 2.70 0.10 symbol p p0 p2 t w specification (mm) 20.0 0.10 4.00 0.10 2.00 0.10 0.30 0.05 32.0 0.30 ? tape material : black ps material, in line with rohs environmental management substances ? tape thickness: 0.3 mm 0.05 mm ? tape width: 32mm (1.3") ? protection zone: black ps material ? distance between chain hole centers within the range of 0.2 mm of cumulative error ? anti - camber at 1 mm / 250 mm ? all dimensions in line with the requirements of eia - 481 - d
packaging, handling an d storage, rohs , section 8 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 24 figure 16 - reel specifications symbol a b c1 d e h t specification (mm) 2.5 0.2 11 0.2 330 1 99.5 0.1 13.2 0.2 32.8 + 0.3 / - 0.2 2.25 0.2
ordering information , section 9 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 25 9 ordering information the amw x 06 module is available individually or in a bulk reel of 900 units as described in table 14 . table 14 . ordering information part number description AMW006/s 1 x AMW006 module with wiconnect pre - installed. each module is individually packaged in an esd bag. AMW006/r a single reel containing 900 x AMW006 modules, each with wiconnect pre - installed. the en- tire reel is packaged in an esd and msl3 - rated moisture sensitive bag. part number description amw106 /s 1 x amw106 module with wiconnect pre - installed. each module is individually packaged in an esd bag. amw106 / r a single reel containing 900 x amw106 modules, each with wiconnect pre - installed. the en- tire reel is packaged in an esd and msl3 - rated moisture sensitive bag.
revision history & glossary , section 10 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 26 10 r evision history & glossary 10.1 revision history table 15 : document revision history revision date change description ads - m w006 - 100r oct 20 , 2014 initial preliminary release ads - mw006 - 101 r nov 25, 2014 updated schematic, pcb trace antenna ads - mw006 - 102 r mar 20, 2015 added note on reset pin ads - mw006 - 103r apr 10, 2015 added note on mls3 non - compliance, and note on power consumption ads - mw006 - 104r may 5, 2015 added solder re flow charts, amw106 properties ads - mw006 - 105r jun 9, 2015 removed amw106 propertie s; u pdated gpio and adc details ads - mwx06 - 10 6 r s ep 1 , 2015 added amw106 updated/added etsi/ce v1.9.1 and japan certification added tape and reel specifications. 10.2 glossary in most cases, acronyms and abbreviations are defined on first use. a comprehensive list of acronyms and other terms used in ackme networks documents are provided on the ackme networks website at https://www.ack.me/faqs/glossary_of_terms .
references , section 11 AMW006 / amw106 ? embedded wi - fi networking solutions ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 ?201 4 - 2015 ackme networks. http://ack.me page | 27 11 references thro ughout this data sheet, referen ces to other docu- ments are listed. the following documents provide addi- tional material: 1. ieee 802.11 standard C 2012 institu t e of electrical and electronics engineers. http://standards.ieee.org
AMW006 / amw106 ? embedded wi - fi networking solutions ack me reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. information furnished by ack me is believed to be accurate and reliable. however, ack me does not assume any liability aris ing out of the application or use of this information, nor the application or use of any product described herein, neither does it convey an y license under its patent rights nor the rights of others . ack me networks us headquarters: 20 north santa cruz ave los gatos ca 95030 ? 2014 - 2015 ack me networks inc. all rights reserved. ads - mwx06 - 106r ? preliminary data sheet september 1, 2015 contact information +1 (408) 402 8160 http://ack.me/contact phone:

▲Up To Search▲

Price & Availability of AMW006

	To Download AMW006 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .