|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
vtm ? current multiplier rev 1.3 vicorpower.com page 1 of 18 07/2015 800 927.9474 high efficiency, sine amplitude converter? vtm current multiplier s nrtl cus 480 006 a00 y e 48 vtm x features ? 48 vdc to 48 vdc 6.3 a current multiplier - operating from standard 48 v or 24 v prm ? regulators ? high efficiency (> 96 %) reduces system power consumption ? high density ( 21 a /in 3 ) ? ? full chip ? vi chip ? package enables surface mount, low impedance interconnect to system board ? contains built-in protection features against: - overvoltage lockout - overcurrent - short circuit - overtemperature ? provides enable / disable control, internal temperature monitoring ? zvs / zcs resonant sine amplitude converter topology ? less than 50oc temperature rise at full load in typical applications typical applications ? high end computing systems ? automated test equipment ? high density power supplies ? communications systems description the vi chip ? current multiplier is a high efficiency (> 96 %) sine amplitude converter? (sac) operating from a 26 to 55 vdc primary bus to deliver an isolated output. the sine amplitude converter offers a low ac impedance beyond the bandwidth of most downstream regulators; therefore capacitance normally at the load can be located at the input to the sine amplitude converter. since the k factor of the VTM48EF480T006A00 is 1 , the capacitance value can be reduced by a factor of 1 , resulting in savings of board area, materials and total system cost. the VTM48EF480T006A00 is provided in a vi chip package compatible with standard pick-and-place and surface mount assembly processes. the co-molded vi chip package provides enhanced thermal management due to a large thermal interface area and superior thermal conductivity. the high conversion efficiency of the VTM48EF480T006A00 increases overall system efficiency and lowers operating costs compared to conventional approaches. the VTM48EF480T006A00 enables the utilization of factorized power architecture? which provides efficiency and size benefits by lowering conversion and distribution losses and promoting high density point of load conversion. v in = 26 to 55 v v out = 26.0 to 55.0 v ( no load ) i out = 6.3 a ( nom ) k = 1 v in l o a d pr pc vc tm il os sg prm regulator cd -out +out -in +in pc vc tm -out +out -in +in regulator voltage transformer factorized power architecture tm vtm transformer ( s ee applica t io n no t e an:024 ) part number package style product grade f = j-lead t = -40 to 125c t = through hole m = -55 to 125c part numbering for storage and operating temperatures see section 6.0 general characteristics 480 x y 006 a00 e 48 vtm typical application
vtm ? current multiplier rev 1.3 vicorpower.com page 2 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x attribute symbol conditions / notes min typ max unit input voltage range v in no external vc applied 26 55 v dc vc applied 0 55 v in slew rate dv in /dt 1 v/s v in uv turn off v in _ uv module latched shutdown, 24 26 v no external vc applied, i out = 6.3 a no load power dissipation p nl v in = 48 v 2.3 10.0 w v in = 26 v to 55 v 11 v in = 48 v, t c = 25 oc 3.4 4.5 v in = 26 v to 55 v, t c = 2 oc 7 inrush current peak i inrp vc enable, v in = 48 v, c out = 100 f, 16.5 24 a r load = 7443 m dc input current i in _ dc 6.4 a transfer ratio k k = v out /v in , i out = 0 a 1 v/ v output voltage v out v out = v in ? k - i out ? r out , section 11 v output current (average) i out _ avg 6.3 a output current (peak) i out _ pk t peak < 10 ms, i out _ avg 6.3 a 7.9 a output power (average) p out _ avg i out _ avg 6.3 a 300 w v in = 48 v, i out = 6.3 a 95.0 96.2 efficiency (ambient) h amb v in = 26 v to 55 v, i out = 6.3 a 93.3 % v in = 48 v, i out = 3.15 a 95.5 96.4 efficiency (hot) h hot v in = 48 v, t c = 100c, i out = 6.3 a 94.4 95.6 % efficiency (over load range) h 20% 1.26 a < i out < 6.3 a 80.0 % output resistance (cold) r out _ cold t c = -40c, i out = 6.3 a 98.0 133.0 170.0 m output resistance (ambient) r out _ amb t c = 25c, i out = 6.3 a 120 176.0 250.0 m output resistance (hot) r out _ hot t c = 100c, i out = 6.3 a 180.0 230.0 280.0 m switching frequency f sw 1.64 1.67 1.70 mhz output ripple frequency f sw _ rp 3.28 3.34 3.40 mhz output voltage ripple v out _ pp c out = 0 f, i out = 6.3 a, v in = 48 v, 360 500 mv 20 mhz bw, section 12 output inductance (parasitic) l out _ par frequency up to 30 mhz, 600 ph simulated j-lead model output capacitance (internal) c out _ int effective value at 48 v out 3.5 f output capacitance (external) c out _ ext vtm standalone operation. 100 f v in pre-applied, vc enable protection overvoltage lockout v in _ ovlo + module latched shutdown 55.1 58.5 60.0 v overvoltage lockout t ovlo effective internal rc filter 8 s response time constant output overcurrent trip i ocp 6.4 10 15 a short circuit protection trip current i scp 16 a output overcurrent t ocp effective internal rc filter (integrative). 3.8 ms response time constant short circuit protection response time t scp from detection to cessation 1 s of switching (instantaneous) thermal shutdown setpoint t j _ otp 125 130 135 oc reverse inrush current protection reverse inrush protection disabled for this product. 1.0 absolute maximum voltage ratings the absolute maximum ratings below are stress ratings only. operation at or beyond these maximum ratings can cause permanent damage to the device. 2.0 electrical characteristics specifications apply over all line and load conditions unless otherwise noted; boldface specifications apply over the temperature range of -40c < t j < 125 c (t-grade) ; all other specifications are at t j = 25oc unless otherwise noted. min max unit + in to - in . . . . . . . . . . . . . . . . . . . . . . . -1.0 60 v dc pc to - in . . . . . . . . . . . . . . . . . . . . . . . . -0.3 20 v dc tm to -in . . . . . . . . . . . . . . . . . . . . . . . . -0.3 7 v dc min max unit vc to - in . . . . . . . . . . . . . . . . . . . . . . . . -0.3 20 v dc + in / - in to + out / - out (hipot) . . . 2250 v dc + out to - out ....................................... -0.5 60 v dc vtm ? current multiplier rev 1.3 vicorpower.com page 3 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x signal type state attribute symbol conditions / notes min typ max unit external vc voltage v vc _ ext required for start up, and operation 11.5 16.5 v below 26 v. see section 7. vc = 11.5 v, v in = 0 v 150 200 vc current draw i vc vc = 11.5 v, v in > 26 v 0 ma vc = 16.5 v, v in > 26 v 0 steady fault mode. vc > 11.5 v 60 analog vc internal diode rating d vc _ int 100 v input vc internal resistor r vc - int 0.51 k vc internal resistor t vc _ coeff 900 ppm/c temperature coefficient start up vc start up pulse v vc _ sp tpeak <18 ms 20 v vc slew rate dvc/dt required for proper start up; 0.02 0.25 v/s vc inrush current i inr _ vc vc = 16.5 v, dvc/dt = 0.25 v/s 1 a vc to v out turn-on delay t on v in pre-applied, pc floating, 500 s vc enable, c pc = 0 f transitional vc to pc delay t vc_pc vc = 11.5 v to pc high, v in = 0 v, 75 125 s dvc/dt = 0.25 v/s internal vc capacitance c vc _ int vc = 0 v 3.2 f ? used to wake up powertrain circuit. ? a minimum of 11.5 v must be applied indefinitely for v in < 26 v to ensure normal operation. ? vc slew rate must be within range for a succesful start. ?prm ? vc can be used as valid wake-up signal source. ? internal resistance used in ?adaptive loop? compensation ? vc voltage may be continuously applied vtm control : vc 3.0 signal characteristics specifications apply over all line and load conditions unless otherwise noted; boldface specifications apply over the temperaturerange of -40c < t j < 125c (t-grade) ; all other specifications are at t j = 25c unless otherwise noted. signal type state attribute symbol conditions / notes min typ max unit pc voltage v pc 4.7 5.0 5.3 v analog steady pc source current i pc _ op 2 ma output pc resistance (internal) r pc _ int internal pull down resistor 50 150 400 k start up pc source current i pc _ en 50 100 300 a pc capacitance (internal) c pc _ int section 7 0 pf pc resistance (external) r pc _ s 60 k enable pc voltage v pc _ en 2 2.5 3 v digital disable pc voltage (disable) v pc _ dis 2 v input / ouput pc pull down current i pc _ pd 5.1 ma transitional pc disable time t pc _ dis _ t 5 s pc fault response time t fr _ pc from fault to pc = 2 v 100 s ? the pc pin enables and disables the vtm. when held below 2 v, the vtm will be disabled. ? pc pin outputs 5 v during normal operation. pc pin is equal to 2.5 v during fault mode given v in > 26 v or vc > 11.5 v. ? after successful start up and under no fault condition, pc can be used as a 5 v regulated voltage source with a 2 ma maximum current. ? module will shutdown when pulled low with an impedance less than 400 ?. ? in an array of vtms, connect pc pin to synchronize start up. ? pc pin cannot sink current and will not disable other modules during fault mode. primary control : pc vtm ? current multiplier rev 1.3 vicorpower.com page 4 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x signal type state attribute symbol conditions / notes min typ max unit tm voltage v tm _ amb t j controller = 27c 2.95 3.00 3.05 v analog tm source current i tm 100 a output steady tm gain a tm 10 mv/c tm voltage ripple v tm _ pp c tm = 0 f, v in = 48 v, 120 200 mv i out = 6.3 a disable tm voltage v tm _ dis 0 v digital output tm resistance (internal) r tm _ int internal pull down resistor 25 40 50 k transitional tm capacitance (external) c tm _ ext 50 pf (fault flag) tm fault response time t fr _ tm from fault to tm = 1.5 v 10 s ? the tm pin monitors the internal temperature of the vtm controller ic within an accuracy of 5c. ? can be used as a "power good" flag to verify that the vtm is operating. ? the tm pin has a room temperature setpoint of 3 v and approximate gain of 10 mv/c. ? output drives temperature shutdown comparator temperature monitor : tm 4.0 timing diagram 12 7 v pri 1. initiated v c pulse 2. controller start 3. v pri ramp up 4. v pri = v ovlo 5. v pri ramp down no v c pulse 6. overcurrent, secondary 7. start up on short circuit 8. pc driven low v sec pc 3 v vc nl 5 v v ovlo tm v tm-amb c notes: C timing and voltage is not to scale C error pulse width is load dependent a: vc slew rate (dvc/dt) b: minimum vc pulse rate c: t ovlo_pin d: t ocp_sec e: secondary turn on delay (t on ) f: pc disable time (t pc_dis_t ) g: vc to pc delay (t vc_pc ) d i sec i sec i sec v vc-ext 3 45 6 a b 8 g e f 26 v vtm ? current multiplier rev 1.3 vicorpower.com page 5 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x 5.0 application characteristics the following values, typical of an application environment, are collected at t c = 25oc unless otherwise noted. see associated figures for general trend data. attribute symbol conditions / notes typ unit no load power dissipation p nl v in = 48 v, pc enabled 3.2 w efficiency (ambient) h amb v in = 48 v, i out = 6.3 a 96.0 % efficiency (hot) h hot v in = 48 v, i out = 6.3 a, t c = 100oc 95.6 % output resistance (cold) r out _ cold v in = 48 v, i out = 6.3 a, t c = -40oc 172.6 m output resistance (ambient) r out _ amb v in = 48 v, i out = 6.3 a 241.1 m output resistance (hot) r out _ hot v in = 48 v, i out = 6.3 a, t c = 100oc 282.0 m output voltage ripple v out _ pp c out = 0 f, i out = 6.3 a, v in = 48 v, 257 mv 20 mhz bw, section 12 v out transient (positive) v out _ tran + i out _ step = 0 a to 6.3 a, v in = 48 v, 2300 mv i slew = 19 a /us v out transient (negative) v out _ tran - i out _ step = 6.3 a to 0 a, v in = 48 v 2300 mv i slew = 85 a /us input voltage (v) power dissipation (w) -40? 25? 100? t : case 1 2 3 4 5 6 7 26 29 32 35 38 41 43 46 49 52 55 no load power dissipation vs. line full load efficiency vs. t case case temperature (c) full load efficiency (%) 26 v 48 v 55 v v : in 92 94 96 98 -40 -20 0 20 40 60 80 100 efficiency & power dissipation -40? case load current (a) efficiency (%) 26 v 48 v 55 v v : in 26 v 48 v 55 v power dissipation (w) 0 3 6 9 12 15 18 21 24 27 80 82 84 86 88 90 92 94 96 98 0 1 2 3 4 5 6 7 p d efficiency & power dissipation 25? case load current (a) efficiency (%) 26 v 48 v 55 v v : in 26 v 48 v 55 v power dissipation (w) 0 3 6 9 12 15 18 21 24 27 80 82 84 86 88 90 92 94 96 98 0 1 2 3 4 5 6 7 p d figure 1 ? no load power dissipation vs. v in figure 2 ? full load efficiency vs. temperature figure 3 ? efficiency and power dissipation at ?40c figure 4 ? efficiency and power dissipation at 25c vtm ? current multiplier rev 1.3 vicorpower.com page 6 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x figure 10 ? start up from application of v in ; vc pre-applied c out = 100 f output voltage (v) output current (a) safe operating area 0 2 4 6 8 10 12 14 16 18 20 0 10 20 30 40 50 60 10ms max continuous figure 8 ? safe operating area figure 9 ? full load ripple, 100 f c in ; no external c out . board mounted module, scope setting : 20 mhz analog bw load current (a) 26 v 48 v 55 v v : in output voltage ripple vs. load v ripple (mv pk-pk ) 25 75 125 175 225 275 325 375 0 1 2 3 4 5 6 7 figure 7 ? v ripple vs. i out ; no external c out . board mounted module, scope setting : 20 mhz analog bw efficiency & power dissipation 100? case load current (a) 26 v 48 v 55 v v : in 26 v 48 v 55 v power dissipation (w) efficiency 0 3 6 9 12 15 18 21 24 27 80 82 84 86 88 90 92 94 96 98 0 1 2 3 4 5 6 7 p d r out (m w ) ) case temperature (c) r out vs. t case at v in = 48 v full load 100 125 150 175 200 225 250 275 300 -40 -20 0 20 40 60 80 100 figure 5 ? efficiency and power dissipation at 100c figure 6 ? r out vs. temperature vtm ? current multiplier rev 1.3 vicorpower.com page 7 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x figure 13 ? full load ? 0 a transient response: c in = 100 f, no external c out figure 12 ? 0 a? full load transient response: c in = 100 f, no external c out figure 11 ? start up from application of vc; v in pre-applied c out = 100 f vtm ? current multiplier rev 1.3 vicorpower.com page 8 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x attribute symbol conditions / notes min typ max unit mechanical length l 32.25 / [1.270] 32.5 / [1.280] 32.75 / [1.289] mm/[in] width w 21.75 / [0.856] 22.0 / [0.866] 22.25 / [0.876] mm/[in] height h 6.48 / [0.255] 6.73 / [0.265] 6.98 / [0.275] mm/[in] volume vol no heat sink 4.81 / [0.294] cm 3 /[in 3 ] weight w 15.0 / [0.53] g/[oz] nickel 0.51 2.03 lead finish palladium 0.02 0.15 m gold 0.003 0.051 thermal VTM48EF480T006A00 (t-grade) -40 125 c operating temperature t j vtm48ef480m0006a00 (m-grade) -55 125 c vtm48et480t006a00 (t-grade) -40 125 c vtm48et480m006a00 (m-grade) -55 125 c thermal r esistance f jc isothermal heat sink and 1 c/w isothermal internal pcb thermal capacity 5 ws/c assembly peak compressive force supported by j-lead only 6 lbs applied to case (z-axis) 5.41 lbs / in 2 VTM48EF480T006A00 (t-grade) -40 125 c storage temperature t st vtm48ef480m0006a00 (m-grade) -65 125 c vtm48et480t006a00 (t-grade) -40 125 c vtm48et480m006a00 ( m-grade) -65 125 c esd hbm 1000 esd withstand esd cdm 400 v dc soldering peak temperature during reflow msl 4 (datecode 1528 and later) 245 c peak time above 217c 60 90 s peak heating rate during reflow 1.5 3 c/s peak cooling rate post reflow 1.5 6 c/s safety isolation voltage (hipot) v hipot 2250 v dc isolation capacitance c in _ out unpowered unit 2500 3200 3800 pf isolation resistance r in _ out 10 m mtbf mil-hdbk-217 plus parts count; 3.8 mhrs 25oc ground benign, stationary, indoors / computer profile telcordia issue 2 - method i case 1; 5.6 mhrs ground benign, controlled ctuvus agency approvals / standards ce marked for low voltage directive and rohs recast directive, as applicable human body model, "jedec jesd 22-a114-f" charge device model, "jedec jesd 22-c101-d" 6.0 general characteristics specifications apply over all line and load conditions unless otherwise noted; boldface specifications apply over the temperature range of -40oc < t j < 125oc (t-grade) ; all other specifications are at t j = 25c unless otherwise noted. vtm ? current multiplier rev 1.3 vicorpower.com page 9 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x 7.0 using the control signals vc, pc, tm, im the vtm control (vc) pin is an input pin which powers the internal vcc circuitry when within the specified voltage range of 11.5 v to 16.5 v. this voltage is required for vtm current multiplier start up and must be applied as long as the input is below 26 v. in order to ensure a proper start, the slew rate of the applied voltage must be within the specified range. some additional notes on the using the vc pin: ? in most applications, the vtm module will be powered by an upstream prm ? regulator which provides a 10 ms vc pulse during start up. in these applications the vc pins of the prm regulator and vtm current multiplier should be tied together. ? the vc voltage can be applied indefinitely allowing for continuous operation down to 0 v in . ? the fault response of the vtm module is latching. a positive edge on vc is required in order to restart the unit. if vc is continuously applied the pc pin may be toggled to restart the vtm module. primary control (pc) pin can be used to accomplish the following functions: ? delayed start: upon the application of vc, the pc pin will source a constant 100 a current to the internal rc network. adding an external capacitor will allow further delay in reaching the 2.5 v threshold for module start. ? auxiliary voltage source: once enabled in regular operational conditions (no fault), each vtm pc provides a regulated 5 v, 2 ma voltage source. ? output disable: pc pin can be actively pulled down in order to disable the module. pull down impedance shall be lower than 400 . ? fault detection flag: the pc 5 v voltage source is internally turned off as soon as a fault is detected. it is important to notice that pc doesn?t have current sink capability. therefore, in an array, pc line will not be capable of disabling neighboring modules if a fault is detected. ? fault reset: pc may be toggled to restart the unit if vc is continuously applied. temperature monitor (tm) pin provides a voltage proportional to the absolute temperature of the converter control ic. it can be used to accomplish the following functions: ? monitor the control ic temperature: the temperature in kelvin is equal to the voltage on the tm pin scaled by 100. (i.e. 3.0 v = 300 k = 27oc). if a heat sink is applied, tm can be used to thermally protect the system. ? fault detection flag: the tm voltage source is internally turned off as soon as a fault is detected. for system monitoring purposes (microcontroller interface) faults are detected on falling edges of tm signal. 8.0 start up behavior depending on the sequencing of the vc with respect to the input voltage, the behavior during start up will vary as follows: ? normal operation (vc applied prior to v in ): in this case the controller is active prior to ramping the input. when the input voltage is applied, the vtm module output voltage will track the input (see figure 10). the inrush current is determined by the input voltage rate of rise and output capacitance. if the vc voltage is removed prior to the input reaching 26 v, the vtm may shut down. ? stand-alone operation (vc applied after v in ): in this case the vtm output will begin to rise upon the application of the vc voltage (see figure 11). the adaptive soft start circuit (see section 11) may vary the ouput rate of rise in order to limit the inrush current to its maximum level. when starting into high capacitance, or a short, the output current will be limited for a maximum of 1200 sec. after this period, the adaptive soft start circuit will time out and the vtm module may shut down. no restart will be attempted until vc is re-applied or pc is toggled. the maximum output capacitance is limited to 100 f in this mode of operation to ensure a sucessful start. 9.0 thermal considerations vi chip ? products are multi-chip modules whose temperature distribution varies greatly for each part number as well as with the input /output conditions, thermal management and environmental conditions. maintaining the top of the VTM48EF480T006A00 case to less than 100oc will keep all junctions within the vi chip module below 125oc for most applications. the percent of total heat dissipated through the top surface versus through the j-lead is entirely dependent on the particular mechanical and thermal environment. the heat dissipated through the top surface is typically 60%. the heat dissipated through the j-lead onto the pcb board surface is typically 40%. use 100% top surface dissipation when designing for a conservative cooling solution. it is not recommended to use a vi chip module for an extended period of time at full load without proper heat sinking. vtm ? current multiplier rev 1.3 vicorpower.com page 10 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x -v out +v ini v ref tm pc temperature dependent voltage source -v in 2.5 v 100 a 5 v 40 k 1000 pf 10.5 v 2.5 v differential primary current sensing v ref enable 1.5 k synchronous rectification primary stage & resonant tank pc pull-up & source overtemperature protection fast current limit vc c in 18 v power transformer q1 q2 q6 primary gate drive secondary gate drive fault logic regulator supply enable adaptive soft start enable q5 cr lr 0.01 f 1 k 2 ma c out modulator enable 150 k v dd v dd v dd +v out q3 q4 gate drive supply d vc_int r vc_int v in ovlo uvlo slow current limit over current protection 10.0 vtm module block diagram vtm ? current multiplier rev 1.3 vicorpower.com page 11 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x 11.0 sine amplitude converter tm point of load conversion the sine amplitude converter (sac) uses a high frequency resonant tank to move energy from input to output. (the resonant tank is formed by cr and leakage inductance lr in the power transformer windings as shown in the vtm module block diagram. see section 10). the resonant lc tank, operated at high frequency, is amplitude modulated as a function of input voltage and output current. a small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving power density. the VTM48EF480T006A00 sac can be simplified into the following model: at no load: v out = v in ? k (1) k represents the ?turns ratio? of the sac. rearranging eq (1): k= v out (2) v in in the presence of load, v out is represented by: v out = v in ? k ? i out ? r out (3) and i out is represented by: i out = i in ?i q (4) k r out represents the impedance of the sac, and is a function of the r dson of the input and output mosfets and the winding resistance of the power transformer. i q represents the quiescent current of the sac control and gate drive circuitry. the use of dc voltage transformation provides additional interesting attributes. assuming that r out = 0 and i q = 0 a, eq. (3) now becomes eq. (1) and is essentially load independent, resistor r is now placed in series with v in as shown in figure 15. the relationship between v in and v out becomes: v out = (v in ?i in ? r) ? k (5) substituting the simplified version of eq. (4) (i q is assumed = 0 a) into eq. (5) yields: v out = v in ? k ? i out ? r ? k 2 (6) + + v out c out v in v?i k + + c in i out r c out i q r out r c in 71 ma 1 ? i out 1 ? v in 176.0 m r cin 0.57 m 17000 ph 0.5 r cout 850 3.5 f l out = 600 ph 2 f i q l in = 5.8 nh i out r out v in v out r sac k = 1/32 vin vout + ? v in v out r sac? k = 1/32 figure 15 ? k = 1/32 sine amplitude converter? with series input resistor figure 14 ? vi chip ? module ac model c out c in vtm ? current multiplier rev 1.3 vicorpower.com page 12 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x this is similar in form to eq. (3), where r out is used to represent the characteristic impedance of the sac?. however, in this case a real r on the input side of the sac is effectively scaled by k 2 with respect to the output. assuming that r = 1 , the effective r as seen from the secondary side is 0.98 m , with k = 1/32 as shown in figure 15. a similar exercise should be performed with the additon of a capacitor or shunt impedance at the input to the sac. a switch in series with v in is added to the circuit. this is depicted in figure 16. a change in v in with the switch closed would result in a change in capacitor current according to the following equation: i c (t) = c dv in (7) dt assume that with the capacitor charged to v in , the switch is opened and the capacitor is discharged through the idealized sac. in this case, i c =i out ? k (8) substituting eq. (1) and (8) into eq. (7) reveals: i out = c ? dv out (9) k 2 dt the equation in terms of the output has yielded a k 2 scaling factor for c, specified in the denominator of the equation. a k factor less than unity, results in an effectively larger capacitance on the output when expressed in terms of the input. with a k= 1/32 as shown in figure 16, c = 1 f would appear as c = 1024 f when viewed from the output. low impedance is a key requirement for powering a high- current, low voltage load efficiently. a switching regulation stage should have minimal impedance while simultaneously providing appropriate filtering for any switched current. the use of a sac between the regulation stage and the point of load provides a dual benefit of scaling down series impedance leading back to the source and scaling up shunt capacitance or energy storage as a function of its k factor squared. however, the benefits are not useful if the series impedance of the sac is too high. the impedance of the sac must be low, i.e. well beyond the crossover frequency of the system. a solution for keeping the impedance of the sac low involves switching at a high frequency. this enables small magnetic components because magnetizing currents remain low. small magnetics mean small path lengths for turns. use of low loss core material at high frequencies also reduces core losses. the two main terms of power loss in the vtm module are: - no load power dissipation (p nl ): defined as the power used to power up the module with an enabled powertrain at no load. - resistive loss (r out ): refers to the power loss across the vtm modeled as pure resistive impedance. p dissipated = p nl + p r out (10) therefore, p out = p in ?p dissipated = p in ?p nl ?p r out (11) the above relations can be combined to calculate the overall module efficiency: h = p out = p in ?p nl ?p r out (12) p in p in = v in ? i in ?p nl ?(i out ) 2 ? r out v in ? i in =1 ? ( p nl + (i out ) 2 ? r out ) v in ? i in c s sac k = 1/32 vin vout + ? v in v out c sac ? k = 1/32 figure 16 ? sine amplitude converter? with input capacitor s vtm ? current multiplier rev 1.3 vicorpower.com page 13 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x 12.0 input and output filter design a major advantage of a sac system versus a conventional pwm converter is that the former does not require large functional filters. the resonant lc tank, operated at extreme high frequency, is amplitude modulated as a function of input voltage and output current and efficiently transfers charge through the isolation transformer. a small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving high power density. this paradigm shift requires system design to carefully evaluate external filters in order to: 1.guarantee low source impedance. to take full advantage of the vtm module dynamic response, the impedance presented to its input terminals must be low from dc to approximately 5 mhz. input capacitance may be added to improve transient performance or compensate for high source impedance. 2.further reduce input and /or output voltage ripple without sacrificing dynamic response. given the wide bandwidth of the vtm module, the source response is generally the limiting factor in the overall system response. anomalies in the response of the source will appear at the output of the vtm module multiplied by its k factor. 3.protect the module from overvoltage transients imposed by the system that would exceed maximum ratings and cause failures. the vi chip ? module input/output voltage ranges must not be exceeded. an internal overvoltage lockout function prevents operation outside of the normal operating input range. even during this condition, the powertrain is exposed to the applied voltage and power mosfets must withstand it. 13.0 capacitive filtering considerations for a sine amplitude converter? it is important to consider the impact of adding input and output capacitance to a sine amplitude converter on the system as a whole. both the capacitance value and the effective impedance of the capacitor must be considered. a sine amplitude converter has a dc r out value which has already been discussed in section 11. the ac r out of the sac contains several terms: ? resonant tank impedance ? input lead inductance and internal capacitance ? output lead inductance and internal capacitance the values of these terms are shown in the behavioral model in section 11. it is important to note on which side of the transformer these impedances appear and how they reflect across the transformer given the k factor. the overall ac impedance varies from model to model. for most models it is dominated by dc r out value from dc to beyond 500 khz. the behavioral model in section 11 should be used to approximate the ac impedance of the specific model. any capacitors placed at the output of the vtm module reflect back to the input of the module by the square of the k factor (eq. 9) with the impedance of the module appearing in series. it is very important to keep this in mind when using a prm ? regulator to power the vtm module. most prm modules have a limit on the maximum amount of capacitance that can be applied to the output. this capacitance includes both the prm output capacitance and the vtm module output capacitance reflected back to the input. in prm module remote sense applications, it is important to consider the reflected value of vtm module output capacitance when designing and compensating the prm module control loop. capacitance placed at the input of the vtm module appear to the load reflected by the k factor with the impedance of the vtm module in series. in step-down ratios, the effective capacitance is increased by the k factor. the effective esr of the capacitor is decreased by the square of the k factor, but the impedance of the module appears in series. still, in most step-down vtm modules an electrolytic capacitor placed at the input of the module will have a lower effective impedance compared to an electrolytic capacitor placed at the output. this is important to consider when placing capacitors at the output of the module. even though the capacitor may be placed at the output, the majority of the ac current will be sourced from the lower impedance, which in most cases will be the module. this should be studied carefully in any system design using a module. in most cases, it should be clear that electrolytic output capacitors are not necessary to design a stable, well-bypassed system. vtm ? current multiplier rev 1.3 vicorpower.com page 14 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x v in v out + ? dc z in_eq1 z in_eq2 z out_eq1 z out_eq2 load vtm 1 r o_1 vtm 2 r o_2 vtm n r o_n z out_eqn z in_eqn figure 17 ? vtm module array 14.0 current sharing the sac topology bases its performance on efficient transfer of energy through a transformer without the need of closed loop control. for this reason, the transfer characteristic can be approximated by an ideal transformer with some resistive drop and positive temperature coefficient. this type of characteristic is close to the impedance characteristic of a dc power distribution system, both in behavior (ac dynamic) and absolute value (dc dynamic). when connected in an array with the same k factor, the vtm module will inherently share the load current (typically 5%) with parallel units according to the equivalent impedance divider that the system implements from the power source to the point of load. some general recommendations to achieve matched array impedances: ? dedicate common copper planes within the pcb to deliver and return the current to the modules. ? provide the pcb layout as symmetric as possible. ? apply same input / output filters (if present) to each unit. for further details see an:016 using bcm ? bus converters in high power arrays . 15.0 fuse selection in order to provide flexibility in configuring power systems vi chip ? products are not internally fused. input line fusing of vi chip products is recommended at system level to provide thermal protection in case of catastrophic failure. the fuse shall be selected by closely matching system requirements with the following characteristics: ? current rating (usually greater than maximum current of vtm module) ? maximum voltage rating (usually greater than the maximum possible input voltage) ? ambient temperature ? nominal melting i 2 t 16.0 reverse operation the VTM48EF480T006A00 is capable of reverse operation. if a voltage is present at the output which satisfies the condition v out > v in ? k at the time the vc voltage is applied, or after the unit has started, then energy will be transferred from secondary to primary. the input to output ratio will be maintained. the VTM48EF480T006A00 will continue to operate in reverse as long as the input and output are within the specified limits. the VTM48EF480T006A00 has not been qualified for continuous operation (>10 ms) in the reverse direction. vtm ? current multiplier rev 1.3 vicorpower.com page 15 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x inch mm notes: . dimensions are . 2. unless otherwise specified, tolerances are: .x / [.xx] = + /-0.25 / [.01]; .xx / [.xxx] = + /-0.13 / [.005] 3. p roduct marking on top surface dxf and pdf files are available on vicorpower.com 4 inch mm . dimensions are . 2. unless otherwise specified, tolerances are: .x / [.xx] = + /-0.25 / [.01]; .xx / [.xxx] = + /-0.13 / [.005] 3. p roduct marking on top surface dxf and pdf files are available on vicorpower.com 4 17.2 j-lead package recommended land pattern mm (i n ch) 17.1 j-lead package mechanical drawing vtm ? current multiplier rev 1.3 vicorpower.com page 16 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x inch mm notes: . dimensions are . 2. unless otherwise specified, tolerances are: .x / [.xx] = + /-0.25 / [.01]; .xx / [.xxx] = + /-0.13 / [.005] 3. p roduct marking on top surface dxf and pdf files are available on vicorpower.com 4 inch mm . dimensions are . 2. unless otherwise specified, tolerances are: .x / [.xx] = + /-0.25 / [.01]; .xx / [.xxx] = + /-0.13 / [.005] 3. p roduct marking on top surface dxf and pdf files are available on vicorpower.com 4 17.4 through-hole package recommended land pattern mm (i n ch) 17.3 through-hole package mechanical drawing vtm ? current multiplier rev 1.3 vicorpower.com page 17 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x notes: 1. maintain 3.50 (0.138) dia. keep-out zone free of copper, all pcb layers. 2. (a) minimum recommended pitch is 39.50 (1.555). this provides 7.00 (0.275) component edge-to-edge spacing, and 0.50 (0.020) clearance between vicor heat sinks. (b) minimum recommended pitch is 41.00 (1.614). this provides 8.50 (0.334) component edge-to-edge spacing, and 2.00 (0.079) clearance between vicor heat sinks. 3. vi chip module land pattern shown for reference only; actual land pattern may differ. dimensions from edges of land pattern to push?in holes will be the same for all full-size vi chip products. 4. rohs compliant per cst?001 latest revision. (no grounding clips) (with grounding clips) 5. unless otherwise specified: dimensions are mm (inches) tolerances are: x.x (x.xx) = ?.3 (0.01) x.xx (x.xxx) = ?.13 (0.005) 6. plated through holes for grounding clips (33855) shown for reference, heat sink orientation and device pitch will dictate final grounding solution. 17.5 recommended heat sink push pin location -in pc vc tm + in -out + out -out + out bottom view a b c d e f g h j k l m n p r t 4 3 2 1 a b c d e h j k l m n p r t 17.6 vtm module pin configuration signal name pin designation +in a1-e1, a2-e2 ?in l1-t1, l2-t2 tm h1, h2 vc j1, j2 pc k1, k2 +out a3-d3, a4-d4, j3-m3, j4-m4 ?out e3-h3, e4-h4, n3-t3, n4-t4 vtm ? current multiplier rev 1.3 vicorpower.com page 18 of 18 07/2015 800 927.9474 480 006 a00 y e 48 vtm x vicor?s comprehensive line of power solutions includes high density ac-dc and dc-dc modules and accessory components, fully configurable ac-dc and dc-dc power supplies, and complete custom power systems. information furnished by vicor is believed to be accurate and reliable. however, no responsibility is assumed by vicor for its use. vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. information published by vicor h as been checked and is believed to be accurate at the time it was printed; however, vicor assumes no responsibility for inaccuracies. testing and other quality controls are used to the extent vicor deems necessary to support vicor?s product warranty. except where mandated by government requirements , testing of all parameters of each product is not necessarily performed. specifications are subject to change without notice. vicor?s standard terms and conditions all sales are subject to vicor?s standard terms and conditions of sale, which are available on vicor?s webpage or upon request. product warranty in vicor?s standard terms and conditions of sale, vicor warrants that its products are free from non-conformity to its standard specifications (the ?express limited warranty?). this warranty is extended only to the original buyer for the period expiring two (2) years after t he date of shipment and is not transferable. unless otherwise expressly stated in a written sales agreement signed by a duly authorized vicor signatory, vicor disclaims all representations, liabilities, and warranties of any kind (whether arising by implication or by operation of law) with respect to the products, including, without limitation, any warranties or representations as to merchantability, fitness for particular purpose, infringement of any patent, copyright, or other intellectual property right, or any other matter. this warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, or storage. vico r shall not be liable for collateral or consequential damage. vicor disclaims any and all liability arising out of the application or use of any pro duct or circuit and assumes no liability for applications assistance or buyer product design. buyers are responsible for their products and applications us ing vicor products and components. prior to using or distributing any products that include vicor components, buyers should provide adequate design, testing and operating safeguards. vicor will repair or replace defective products in accordance with its own best judgment. for service under this warranty, the buyer must contact vicor to obtain a return material authorization (rma) number and shipping instructions. products returned without prior author ization will be returned to the buyer. the buyer will pay all charges incurred in returning the product to the factory. vicor will pay all re shipment charges if the product was defective within the terms of this warranty. life support policy vicor?s products are not authorized for use as critical components in life support devices or systems without the express prior written approval of the chief executive officer and general counsel of vicor corporation. as used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and wh ose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a s ignificant injury to the user. a critical component is any component in a life support device or system whose failure to perform can be reasonably expec ted to cause the failure of the life support device or system or to affect its safety or effectiveness. per vicor terms and conditions of sale, the user of vicor products and components in life support applications assumes all risks of such use and indemnifies vicor against all liability and damag es. intellectual property notice vicor and its subsidiaries own intellectual property (including issued u.s. and foreign patents and pending patent applications ) relating to the products described in this data sheet. no license, whether express, implied, or arising by estoppel or otherwise, to any intel lectual property rights is granted by this document. interested parties should contact vicor's intellectual property department. the products described on this data sheet are protected by the following u.s. patents numbers: 5,945,130; 6,403,009; 6,710,257; 6,911,848; 6,930,893; 6,934,166; 6,940,013; 6,969,909; 7,038,917; 7,145,186; 7,166,898; 7,187, 263; 7,202,646; 7,361,844; d496,906; d505,114; d506,438; d509,472; and for use under 6,975,098 and 6,984,965. vicor corporation 25 frontage road andover, ma, usa 01810 tel: 800-735-6200 fax: 978-475-6715 email customer service: custserv@vicorpower.com technical support: apps@vicorpower.com |
Price & Availability of VTM48EF480T006A00 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |