 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| this is information on a product in full production. may 2012 doc id 022698 rev 1 1/53 53 led7708 16 channels x 85 ma led driver with boost controller and 4-wire serial interface datasheet ?production data features boost controller section ? 3.6 v to 36 v input voltage range (ldo) ? adaptive output voltage for high efficiency ? internal +5 v ldo for gate driver supply ? internal +3.3 v ldo for device supply ? high performance external mosfet driver ? 250 khz to 1 mhz switching frequency ? programmable ov and oc protection ? fixed frequency peak current-mode control ? external synchronization for multi-device application ? overtemperature alert and thermal shutdown led array driver section ? 16 channels with 85 ma/ch current capability ? 2% channel current accuracy ? 2% channel-to-channel current matching ? led short-circuit and open channel fault detection and management ? 4-wire, 30 mhz serial interface ? 16 x16-bit, 1x256-bit or 1x192-bit serial data formats ? grouped or independent channel pwm control ? selectable 12/16-bit grayscale brightness control for local dimming ? programmable internal dimming oscillator ? programmable grayscale latency ? master/slave chain configuration supported applications tv and monitor backlight units for lcd panels medium and large size lcd panel backlights rgb/rggb backlight solutions description the led7708 has been specifically designed to supply several leds starting from a single low- voltage rail. it integrates a boost controller, sixteen current generators and a 4-wire serial interface. the boost controller regulates the output voltage in an adaptive way, according to the led requirements, resulting in an improved overall efficiency. all the current generators are 40 v-rated, allowing the led7708 to drive several leds in series on each channel. the channels can be put in parallel for higher output current. the brightness of the leds is controlled by using the serial interface. a selectable 12-bit or 16-bit grayscale brightness control allows independent pwm on each channel. a programmable on-chip dimming oscillator is provided for external circuitry simplification. the device has dedicated pins to lock to an external synchronization with other devices (master or slave) for noise reduction in multi-device applications. the led7708 implements basic protection (ovp, ocp and thermal shutdown) as well as led array protection. it can detect and manage open-led and shorted-led faults and different fault- management options are available in order to cover most application needs. table 1. device summary order codes package packing led7708 vfqfpn-48 7x7 (exposed pad) tu b e LED7708TR tape and reel 6 & 1 & 0 . x x , p i t c h www.st.com
contents led7708 2/53 doc id 022698 rev 1 contents 1 typical application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4 recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1 device supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8 recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 19 8.1 device power-up and soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 8.2 device shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8.3 boost controller section and output voltage control . . . . . . . . . . . . . . . . . 21 8.3.1 output voltage optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8.3.2 boost converter loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.3.3 slope compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 8.3.4 external mosfet control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8.4 current generators section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 8.5 serial interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8.5.1 serial interface architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8.5.2 serial interface internal registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8.5.3 internal registers access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 8.5.4 brightness data formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8.5.5 brightness registers (brtxx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 8.5.6 devcfg0 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 8.5.7 devcfg1 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 8.5.8 gslat register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 8.5.9 chsel register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 led7708 contents doc id 022698 rev 1 3/53 8.5.10 chsta register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.5.11 internal registers initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.6 dimming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.6.1 internal dimming oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.6.2 dimming waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.6.3 grayscale synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.7 fault management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8.7.1 overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8.7.2 overtemperature alert and thermal protection . . . . . . . . . . . . . . . . . . . . 44 8.7.3 overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8.7.4 led short-circuit and open channel faults . . . . . . . . . . . . . . . . . . . . . . . 44 8.8 special function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.8.1 current generators gain adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.8.2 continuous status reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 9 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 list of tables led7708 4/53 doc id 022698 rev 1 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 table 3. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 4. thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 5. recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 6. electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 7. recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 8. output voltage states during regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 table 9. handshake signals summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 10. led current vs. external resistor setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 11. internal registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 12. internal register operations encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 13. brightness data formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 14. devcfg0 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 table 15. devcfg1 register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 table 16. available led short detection thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 17. chsel register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 table 18. chsta register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 19. default configuration of internal registers after por . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 20. fosc pin setting options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 table 21. function of pins involved in dimming control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 table 22. dimming synchronization control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 table 23. detected faulty conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 table 24. xfault pin behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 table 25. vfqfpn48 (7 x 7 x 1.0 mm.) package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . 49 table 26. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 led7708 list of figures doc id 022698 rev 1 5/53 list of figures figure 1. basic application circuit schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 2. pin connection (through top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 3. simplified block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 4. soft-start waveforms (standalone operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 5. simplified output regulation circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 6. effect of slope compensation on small inductor current perturbation (d>0.5) . . . . . . . . . . 26 figure 7. simplified serial interface block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 figure 8. timing diagram related to a devcfgx write operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 figure 9. 16-bit data format, write operation to the brightness register . . . . . . . . . . . . . . . . . . . . . . . 31 figure 10. 256-bit data format, write operation to the brightness registers . . . . . . . . . . . . . . . . . . . . . 32 figure 11. 192-bit data format, write operation to the brightness registers . . . . . . . . . . . . . . . . . . . . . 32 figure 12. dimming signals and synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 0 figure 13. normal timing mode waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 figure 14. inverted timing mode waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 figure 15. dimming waveform and gssy output pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 figure 16. dimming waveform triggered by gssy input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 figure 17. internal signals connected to the xflt pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 figure 18. channels current gain adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 figure 19. continuous reading mode disabled, 1x256-bit data format . . . . . . . . . . . . . . . . . . . . . . . . 46 figure 20. continuous reading mode enabled, 1x256-bit data format . . . . . . . . . . . . . . . . . . . . . . . . . 47 figure 21. vfqfpn48 (7 x 7 x 1.0 mm.) package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 figure 22. recommended pcb footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 typical application circuit led7708 6/53 doc id 022698 rev 1 1 typical application circuit figure 1. basic application circuit schematic ! - v 6 ) . , % $ $ ) . $ / 5 4 $ # , + , % 8 & , 4 3 ' . $ , $ / # , ) - ) 3 % 4 ( # / - 0 8 - 3 + # ( # ( # ( # ( 6 & " # 3 . 3 ' ! 4 % 0 ' . $ 6 $ 2 ' 3 # + & / 3 # ' 3 3 9 ( o s t # o n t r o l l e r , 2 % . 6 ) . 3 , / 0 % & 3 7 ) 3 % 4 , ) / + 6 3 ) 3 9 . # 8 6 / + 6 - ) . 8 / 6 & 4 o s l a v e d e v i c e s o p t i o n a l ! ' . $ led7708 pin function doc id 022698 rev 1 7/53 2 pin function figure 2. pin connection (through top view) ! - v $ ) . $ / 5 4 $ # , + , % ' 3 # + 8 & , 4 ) / + 8 6 / + 6 3 ) ' 3 3 9 8 / 6 & 8 - 3 + 6 ) . , 2 % . 6 $ 2 ' ! 4 % 0 ' . $ # 3 . 3 6 - ) . ! ' . $ 6 & " , $ / # ( # ( ! ' . $ 3 ' . $ ) 3 % 4 , ) 3 % 4 ( # / - 0 3 , / 0 % # , ) - & / 3 # # ( 3 9 . # & 3 7 # ( # ( # ( # ( # ( # ( # ( # ( # ( # ( # ( # ( # ( , % $ table 2. pin description pin function 1 vsi serial interface (si) core and digital i/o buffer supply input. connect to ldo3 or to an external supply (3 v-5 v). insert a 100 nf bypass ceramic capacitor between this pin and sgnd. connect to the host controller?s supply when possible. 2 gssy grayscale synchronization output or vsync input. when the internal dimming generation is set, a pulse at the end of each dimming cycle is provided for data stream synchronization. also used as dimming synchronization input to lock the dimming cycles on the vertical sync pulses. 3 din serial interface data input. 4 dout serial interface data out. 5 dclk serial interface data clock. 6 le serial interface latch enable. 7gsck grayscale clock i/o. when the internal dimming oscillator is used, the grayscale clock is provided at this pin. the pin becomes the grayscale clock input if the internal dimming oscillator is disabled (see fosc pin). 8 xflt fault signal, open drain output. the pin goes low when a faulty condition occurs. 9iok channel current ok handshake i/o. used for extended output voltage regulation in multi- device applications. used by slave devices to request a higher output voltage to the master. a 100 k pull-up resistor to ld03 is required. 10 xvok channel voltage ok i/o (inverted). used for extended output voltage regulation in multi- device applications. used by slave devices to request an output voltage reduction to the master. a 100 k pull-up resistor to ld03 is required. pin function led7708 8/53 doc id 022698 rev 1 11 xovf internal dac overflow i/o. used for extended output voltage regulation and fault management in multi-device applications. it is used to inform slave devices that the maximum output voltage has been reached. a 100 k pull-up resistor to ld03 is required. 12 xmsk fault detection masking i/o. this signal is used for extended output voltage regulation & fault management in multi-device applications. it is used to avoid incorrect fault detection by forcing slave devices to ignore led-short detection during output voltage steering. a 100 k pull-up resistor to ld03 is required. 13 fsw switching frequency selection / synchronization input. used to set the desired switching frequency of the boost controller. also used as synchronization input. 14 sync boost converter synchronization output. the buffered switching clock signal is provided at this pin to eventually synchronize other smps in the host system. 15 fosc dimming oscillator frequency. a resistor to ground sets the frequency of the internal grayscale clock dimming oscillator. if set high, the internal dimming oscillator is disabled and the gsck pin becomes the clock input (see gsck pin). 16 clim boost section current limit setting. a resistor between this pin and sgnd sets the boost converter current limit. 17 slope slope compensation setting. a resistor between this pin and sgnd is required to set the proper amount of slope compensation to avoid sub-harmonic instability. 18 comp transconductance amplifier output. connect a simple rc series between this pin and sgnd to properly compensate the loop-gain of the boost converter. 19 iseth output current setting (on). connect a resistor between this pin and sgnd to set the current sunk by each channel during the on-phase of the dimming. 20 isetl output current setting (off). connect a resistor between this pin and sgnd to set the current sunk by each channel during the off-phase of the dimming (led biasing). connect to ldo3 to disable the bias current. 21 sgnd signal ground. common return for signals and settings. 22 agnd analog ground. common return for the current generators (channels). 23 ch1 driver output (channel) #1. 24 ch2 driver output (channel) #2. 25 ch3 driver output (channel) #3. 26 ch4 driver output (channel) #4. 27 ch5 driver output (channel) #5. 28 ch6 driver output (channel) #6. 29 ch7 driver output (channel) #7. 30 ch8 driver output (channel) #8. 31 ch9 driver output (channel) #9. 32 ch10 driver output (channel) #10. 33 ch11 driver output (channel) #11. 34 ch12 driver output (channel) #12. 35 ch13 driver output (channel) #13. table 2. pin description (continued) pin function led7708 pin function doc id 022698 rev 1 9/53 36 ch14 driver output (channel) #14. 37 ch15 driver output (channel) #15. 38 ch16 driver output (channel) #16. 39 agnd analog ground. common return for the current generators (channels). 40 vmin minimum output voltage setting. multi-level input (high, low, floating or resistor to sgnd). used in conjunction with the vfb pin to set the best output voltage range swing for a given led array. see related section for further details. 41 csns external mosfet current sense input. connect to the sensing resistor in series with the power switch (source of the power mosfet node). 42 pgnd power ground. reference for the external mosfet current sensing circuit and return for the gate driver. 43 gate external mosfet gate driver output. connected to the gate of the power mosfet. 44 vdr gate driver supply. internally connected to the 5 v ldo regulator. bypass with a 1 f ceramic capacitor to pgnd as close as possible to the chip. 45 lren 3.3 v linear regulator enable. when high or floating, the internal 3.3 v linear regulator is used to supply the device. also used to turn off the device for power consumption reduction. to be left floating the internal 3.3 v ldo is overdriven by an external 3.3 v supply rail. 46 vin input of the ldo linear regulators. bypass with a 1f ceramic capacitor to ground as close as possible to the chip. 47 ldo3 3.3 v device supply and internal 3.3 v linear regulator output. bypass with a 1 f ceramic capacitor to ground as close as possible to the chip. 48 vfb output voltage feedback for the boost controller. connect to the central tap of the output resistor divider. see the related section for details. table 2. pin description (continued) pin function absolute maximum ratings led7708 10/53 doc id 022698 rev 1 3 absolute maximum ratings table 3. absolute maximum ratings symbol parameter pin min. max. unit maximum pin voltage vin, ch1 to ch16 -40 v ldo3 - vin+0.3 3.6 comp, sync, iseth, isetl, slope, clim, fosc, vfb, xovf, vmin - ldo3+0.3 3.6 vsi - 6 dclk, le, din, gsck, dclk, dout, gssy - vsi+0.3 6 iok, xmask, xvok, xflt, fsw, lren, -6 vdr - 6 vin+0.3 gate - vdr+0.3 6 csns - ldo3+0.3 3.6 continuous channel current ch1 to ch16 - 90 ma maximum current generator power dissipation ch1 to ch16 - 0.5 w esd esd rating human body model jedec jesd22- a114 -2kv table 4. thermal data symbol parameter conditions min. max. unit p d power dissipation (1) t a = 25 c w t a = 50 c t a = 85 c t j,op operating junction temperature -40 150 c led7708 absolute maximum ratings doc id 022698 rev 1 11/53 t stg storage temperature range -50 150 r th,ja junction-ambient thermal resistance 30 c/w 1. device soldered to the steval-ill035v1 demonstration board. table 4. thermal data (continued) symbol parameter conditions min. max. unit recommended operating conditions led7708 12/53 doc id 022698 rev 1 4 recommended operating conditions table 5. recommended operating conditions symbol parameter conditions min. max. unit dc characteristics v vin vin pin input voltage range 3.6 36 v v ldo3 ldo pin input voltage range vin, ldo3 and vdr shorted together 3.0 3.6 v vdr vdr pin input voltage range vdr and vin shorted together 3.0 5.5 v chx channel voltage range 36 v vsi serial interface supply voltage 3.0 5.5 i chx channel continuous current 20 85 ma channel current when off (adjustable) 2200a ac characteristics (v si = 3.3 v) f gsc grayscale clock frequency 25 mhz f dclk serial clock frequency 30 f sw boost converter switching frequency 200 1000 khz t w,dclk dclk pulse width 20 ns t w,gsc gsc pulse width 20 t w,le le pulse width 15 t su,din din setup time 5 t h,din din hold time 5 t su,le le setup time 5 t h,le le hold time 5 led7708 electrical characteristics doc id 022698 rev 1 13/53 5 electrical characteristics (v in = 12 v; t amb = 25 c and vsi connected to ldo3 if not otherwise specified.) table 6. electrical characteristics symbol parameter conditions min. typ. max. unit supply section lren turn-on threshold 1.4 v lren turn-off threshold 1 a lren pull-up current 3 v uvlo,on ldo3 undervoltage lockout upper threshold 2.9 3.0 v v uvlo,off ldo3 undervoltage lockout lower threshold 2.6 2.7 v vsi,on vsi turn-on threshold 3.0 3.1 v vsi,off vsi turn-off threshold 2.6 2.7 v ldo3 3.3 v ldo output voltage 3.6 v v vin 28 v i ldo3 = 0 ma, den=0 3.2 3.3 3.4 mv 3.3 v ldo load regulation v vin =3.6 v, den=0 0 ma i ldo3 40 ma 30 100 3.3 v ldo drop-out voltage i ldo3 = 40 ma , v ldo3 = 3.2 v 180 270 v vdr 5 v ldo output voltage 6 v v vin 28 v i vdr = 0 ma , den=1 4.5 5.0 5.5 v 5 v ldo load regulation v vin =6 v, den=1 0 ma i vdr 40 ma 6 0 200 mv 5 v ldo drop-out voltage i vdr = 40 ma , v vdr = 4.5 v 150 200 mv boost controller t on,min minimum switching on-time 100 170 ns f sw default switching frequency fsw to ldo3 550 610 670 khz synchronization input frequency 180 1020 k fsw switching frequency constant r fsw = 100 k 4.4 x10 10 5.0 x10 10 5.6 x10 10 hz ? i gate,pk gate driver current capability c l =3.3 nf, sourcing 1.9 a c l =3.3 nf, sinking 2.1 t r,gate gate driver rise time (10 to 90%) c l =3.3 nf 9 ns t f,gate gate driver fall time (90 to10%) 10 electrical characteristics led7708 14/53 doc id 022698 rev 1 fsw synchronization input low level 0.5 v fsw synchronization input high level 2.2 sync output duty cycle fsw connected to ldo3 25 30 35 % sync output high level i sync =1 ma v ldo3 -0.3 v v sync output low level i sync =-1 ma 0.4 adjustable power mosfet current sensing voltage r clim =100 k 100 mv r clim =300 k 300 power consumption i vin1 shutdown current (si off, led drivers off, smps off, ldos off) lren low, vsi low 30 a i vin2 shutdown current (si active, led drivers off, smps off, ldos on) lren floating vsi to ldo3 den=0 300 450 i vin3 quiescent current (led drivers off, boost section not switching) lren floating; vsi, fosc and isetl to ldo3; din, dclk, le, gsck and gssy to gnd; v chx =2 v; r iseth =60 k 4 ma i vin4 operating current (serial interface active, boost not switching) lren floating vsi and fosc to ldo3, din and dclk toggling at 15 mhz, dout, gssy and gsck floating, le to gnd. v chx =2 v, r iseth =60 k 7 i vsi1 standby current (din, dclk and le to sgnd, led drivers off, smps off, lren floating) vsi = 3.3 v 7 a vsi = 5.0 v 9 ov protection, output regulation v fb,ovp overvoltage protection reference threshold v min tied to gnd 1.275 1.30 1.325 v v min to ldo3 1.105 1.13 1.155 r vmin =220 k 0.985 1.01 1.035 v min floating 0.765 0.8 0.815 v fb,ovp ovp hysteresis 6 mv table 6. electrical characteristics (continued) symbol parameter conditions min. typ. max. unit led7708 electrical characteristics doc id 022698 rev 1 15/53 v dac,fb maximum internal reference voltage for output regulation vmin to gnd 1.136 1.161 1.186 v vmin to ldo3 0.967 0.992 1.017 r vmin =220 k 0.847 0.872 0.897 vmin floating 0.630 0.655 0.680 minimum internal reference voltage for output regulation vmin to gnd 0.836 0.861 0.886 vmin to ldo3 0.667 0.692 0.717 r vmin =220 k 0.547 0.572 0.597 vmin floating 0.330 0.355 0.380 current generators i chxn maximum output current accuracy with respect to nominal value (1) v chx = 0 . 6 v, 20 ma i chx 85 ma 2% 3% i chxy maximum channel-to- channel output current mismatch (1) (all channels active) v chx =0.6 v, r iseth =60 k (i chx =20 ma) 2% v chx minimum master channel feedback voltage r iseth =60 k , crs=0 500 600 mv r iseth =15 k , crs=1 700 800 v rw regulation window amplitude r iseth =60 k , rwas=0 190 250 310 r iseth =60 k , rwas=1 400 500 600 i chx,off1 off-state channels current v chx =10 v, r isetl =50 k 70 80 90 a i chx,off2 v chx =10 v , isetl to ldo3 1 2 v th,isetl isetl input threshold i chx, off2 v ldo3 - 1 v k iseth output current high-state constant 20 ma i chx 85 ma 1164 1200 1236 k isetl output current low-state constant 3.5 4.0 4.5 serial interface din, dclk, le, gsck, gssy low level input threshold vsi=ldo3=3.3 v 1.32 v din, dclk, le, gsck, gssy high level input threshold 1.6 dout and gssy output low level vsi=ldo3=3.3 v i load =-200 a 1.22 dout and gssy output high level vsi=ldo3=3.3 v i load =200 a 1.75 table 6. electrical characteristics (continued) symbol parameter conditions min. typ. max. unit electrical characteristics led7708 16/53 doc id 022698 rev 1 fault management v chx,flt1 led short-circuit detection threshold dts0=1& dts1=0 3.0 3.2 3.4 v v chx,flt2 dts0=0& dts1=1 6.2 6.4 6.6 v chx,flt3 dts0=1& dts1=1 7.7 8.0 8.3 xflt output low level i xflt, sink =4 ma 200 220 mv dimming oscillator k osc internal dimming oscillator constant r fosc =33.2 k 3.86 x10 11 4 x10 11 4.14 x10 11 hz? f gsck,osc internal dimming oscillator frequency r fosc =100 k 4 mhz r fosc =16 k 25 thermal flag and protection t ota overtemperature alert threshold 125 c overtemperature alert hysteresis 20 t otp overtemperature protection threshold 155 1. channel current accuracy is calculated as: where x, y=1..16, x y. table 6. electrical characteristics (continued) symbol parameter conditions min. typ. max. unit i chx max i chx i target ? () i target ------------------------------------------------ 100 ? = i chy max i chx i chy ? () i target -------------------------------------- 100 ? = led7708 block diagram doc id 022698 rev 1 17/53 6 block diagram figure 3. simplified block diagram ! - v , $ / # , ) - 3 9 . # & 3 7 $ / 5 4 ' 3 # + , % # / - 0 ) 3 % 4 ( 0 ' . $ # 3 . 3 # ( 6 ) . 3 , / 0 % 8 / 6 & # ( 4 h e r m a l 0 r o t e c t i o n 3 y n c $ e t e c t o r / 3 # 6 o l t a g e s e l e c t o r 5 6 , / $ e t e c t o r 6 , $ / 2 a m p ' e n e r a t o r # u r r e n t 3 e n s e 3 o f t 3 t a r t 6 # ( # u r r e n t , i m i t " o o s t # o n v e r t e r # o n t r o l , o g i c ? g m ? ' ! 4 % ) 3 % 4 , 6 # ( " 2 4 " 2 4 6 3 ) 3 ' . $ & / 3 # 8 - 3 + $ # , + $ ) . 6 & " ? 6 / 6 0 / 6 0 ! ' . $ 6 # ( 6 # ( / 3 # ) / + ) ( ) ( ) , ) , # / 5 . 4 % 2 # / - 0 # / - 0 ' 3 3 9 & a u l t $ e t e c t i o n - a n a g e m e n t , o g i c $ i m m i n g # o n t r o l / 6 0 ! d a p t i v e / u t p u t 6 o l t a g e # o n t r o l # / . & ) ' 3 4 ! 4 5 3 2 % ' ) 3 4 % 2 3 3 e r i a l ) n t e r f a c e # o n t r o l , o g i c 3 5 0 0 , 9 $ % 4 % # 4 / 2 6 $ 2 6 , $ / , 2 % . 8 6 / + 6 - ) . $ ! # 8 & , 4 device description led7708 18/53 doc id 022698 rev 1 7 device description the led7708 is an led driver that integrates a boost controller, sixteen current generators and a 4-wire serial interface. it has been specifically designed for driving the led backlight in medium to large lcd panels. the device is controlled by a 4-wire serial interface and can operate both as standalone driver and as master driver in conjunction with other slave devices. basic and advanced dimming functions are supported in order to meet different application requirements. regardless of the dimming control technique, the led7708 can optimize the power dissipation by controlling the output voltage of the boost converter. two internal linear regulators derive the device supply (3.3 v) and the gate driver supply (5 v) from a single power rail. 7.1 device supply the led7708 integrates two low drop-out linear regulators to derive the +3.3 v (typ.) main supply and the +5 v supply for the gate driver. the vin pin is the input terminal for both linear regulators. the output of the 3.3 v ldo is the ldo3 pin, the output of the 5 v ldo is the vdr pin. the 3.3 v ldo (ldo3 pin) is active if the lren (linear regulator enable) pin is left floating or externally set high (see section 5: electrical characteristics for the thresholds involved). the serial interface i/o stage is supplied through the vsi pin. this pin is used to enable the serial interface and it allows the setting of the logic level of the serial interface signals (3.3 v or 5 v) at the same time. the serial interface can be powered by the internal 3.3 v ldo (by simply connecting the ldo3 pin to the vsi pin) or by an external source, usually the same supply rail as the host controller. when an external +3.3 v source is available, it is possible to bypass the 3.3 v ldo by connecting vin, vdr and ldo3 together to the +3.3 v rail; in this case the gate driver is supplied at 3.3 v too and a super-logic level mosfet is required as the power switch. the 3.3 v regulator is self-protected against overcurrent and thermal damage thanks to a foldback mechanism. the continuous current capability of the 3.3 v ldo is calculated to not exceed the junction temperature limit in worst power dissipation conditions. a 1 f mlcc on the ldo3 pin is required for ripple filtering and ldo output stability. the ldo3 pin is internally connected to the undervoltage lockout (uvlo) protection; the upper and lower uvlo thresholds are reported in section 5: electrical characteristics . when the voltage at the ldo3 pin falls below the lower uvlo threshold, the device is turned off (non-latched condition). the device turns on when the voltage at the ldo3 pin crosses the upper uvlo threshold. crossing the lower and upper thresholds in sequence performs the so called ?power-on reset? (por). the por sequence is used, as well as toggling the internal den bit (see internal registers), when the device is asked to restore normal operation after a latched fault condition. the 5 v linear regulator, whose output is connected to the vdr pin, is turned off when the device is disabled, while the 3.3 v linear regulator is controlled by the lren pin only. led7708 recommended operating conditions doc id 022698 rev 1 19/53 8 recommended operating conditions table 7. recommended operating conditions symbol parameter conditions min. max. unit dc characteristics v vin vin pin input voltage range 3.6 36 v v ldo3 ldo pin input voltage range vin, ldo3 and vdr shorted together 3.0 3.6 v vdr vdr pin input voltage range vdr and vin shorted together 3.0 5.5 v chx channel voltage range 36 v vsi serial interface supply voltage 3.0 5.5 i chx channel continuous current 20 85 ma channel current when off (adjustable) 2200a ac characteristics (v si = 3.3 v) f gsc grayscale clock frequency 25 mhz f dclk serial clock frequency 30 f sw boost converter switching frequency 200 1000 khz t w,dclk dclk pulse width 20 ns t w,gsc gsc pulse width 20 t w,le le pulse width 15 t su,din din setup time 5 t h,din din hold time 5 t su,le le setup time 5 t h,le le hold time 5 recommended operating conditions led7708 20/53 doc id 022698 rev 1 8.1 device power-up and soft-start the vsi pin (supply input for the serial interface) has a high level threshold lower than the upper uvlo threshold at the ldo3 pin, ensuring that the serial interface is enabled prior to the device being turned on. anyway, after the por, the den (device enable) bit of the internal devcfg0 control register is low (default value) and the device is off. the soft-start sequence takes place as soon as this bit is asserted. if the led7708 is set to operate in standalone, the soft-start procedure takes place in two steps ( figure 4 ): 1. the switching frequency is reduced to one fourth of the nominal value and the boost current limit is set to 20%. this phase finishes approximately 1 ms after the output voltage reaches the maximum value (not the ovp level). during this phase the channels are disabled. 2. both the switching frequency and the boost current limit are released to their respective nominal values and then the channels are enabled. figure 4. soft-start waveforms (standalone operation) a slightly different soft-start procedure takes place if the led7708 is set to operate as master in conjunction with other slave devices: 1. the switching frequency is reduced to one eighth of the nominal value and the boost current limit is set to 20%. this phase finishes approximately 1 ms after the output voltage reaches the maximum value (not the ovp level). during this phase the channels are active. 2. the switching frequency is increased to half the nominal value. this phase is held for approximately 2 ms. 3. the switching frequency is further increased to the nominal value while the current limit changes to 40% (~5 ms duration). 4. the current limit is released to its nominal values. led7708 recommended operating conditions doc id 022698 rev 1 21/53 8.2 device shutdown the device is turned off by clearing the den bit of the devcfg0 register. the content of most of the internal registers is not cleared acting on the den bit. the lren pin can be also used to turn the device on and off whenever the internal 3.3 v ldo is used to supply the led7708 (por). in this case the content of the internal registers is lost. 8.3 boost controller section and output voltage control the boost section of the led7708 consists of: fixed-frequency current-mode step-up controller output voltage optimization loop external mosfet gate driver related protection circuitry. 8.3.1 output voltage optimization the output voltage of the boost section is the supply rail for the led strings and is regulated in an adaptive way to improve the overall efficiency. a dedicated digital-to-analog converter (dac) is used to change the reference voltage of the loop and the output voltage is adjusted in order to keep the power dissipation of the led driving section to the minimum level. the optimization is achieved by keeping the voltage drop across the channels inside a fixed window (regulation window) and its amplitude can be selected between two values (300 mv and 600 mv) by acting on the internal registers. the lower threshold of the regulation window (v rwl ) is a function of the set led current ( equation 1 ) and the upper threshold (v rwh ) is therefore determined. equation 1 figure 5 shows the simplified regulation circuit. v rwl k w r iseth ? = recommended operating conditions led7708 22/53 doc id 022698 rev 1 figure 5. simplified output regulation circuitry during normal operation, the regulation algorithm is the following: if at least one active channel has a voltage drop below the lower threshold, the internal dac counts up and the output voltage is increased if all the active channels have a voltage drop higher than the upper threshold, the internal dac counts down and the output voltage is reduced. therefore, the possible operating configurations are shown in ta b l e 8 . the algorithm can also manage faulty conditions that may occur on the led array (open channels and led short-circuit) in order to prevent excessive power dissipation. the led7708 has been designed to interface with other slave devices and can provide them with the correct led supply voltage by extending the above mentioned output voltage optimization. for this purpose, some handshake signals have been reserved: table 8. output voltage states during regulation output voltage condition excessive all the channels have their voltage above the upper threshold of the regulation window. optimal all the channels have their voltage inside the regulation window. regulated most of the channels have their voltage inside the regulation window; the remaining channels have a voltage drop above the upper threshold. insufficient at least one channel has its voltage drop below the lower threshold of the regulation window. ! - v # o u n t e r $ ! # 5 0 $ / 7 . 3 2 1 c l o c k s l o p e # u r r e n t s e n s i n g ) , % $ ) , % $ 6 ' % . - ! 8 6 ' % . - ! 8 6 ) . 6 " / / 3 4 ) , % $ k 6 ' % . m i n ) / + 8 6 / + 6 ' % . led7708 recommended operating conditions doc id 022698 rev 1 23/53 the two signals iok and xvok are connected (wired-or) to all the slave devices sharing the same output voltage rail: if a channel has a low-voltage drop (below v rwl ), the device that owns that channel forces low the iok signal. in a similar way, the xvok is released if the voltage across all the channels of a slave is higher than required (above v rwh ). the wire-or connection of this signal ensures that the output voltage reduction takes place only if all the slaves (and the master itself) need this operation. refer to the special functions section for a detailed explanation of the daisy chain connection between the master and slave devices. the boost converter is always active regardless of how many channels are active (i.e. even if all channels are off) in order to improve the load transient dynamic response. the output voltage regulation can be enabled/disabled (the ovre bit of the devcfg0 register), allowing the user to perform the optimization continuously or on demand. in real applications, the spread of the forward voltage of the leds may cause the channels to have different voltage drops. in any case, the leading channel (i.e. the channel requiring the highest voltage to drive its led string) is kept inside the regulation window. the reference voltage, provided by the internal dac, spans between the minimum and maximum values, programmable through the vmin pin (see section 5: electrical characteristics ). as a consequence, the output voltage can be varied by the device in the following range: equation 2 equation 3 where r1 and r2 are the resistors of the divider connected to the output rail and v vfb is the reference voltage at the vfb pin. the led7708 regulates the output voltage in order to optimize the overall efficiency and, to do this, it needs to read the voltage drop across the active current generators. unfortunately, in some cases (e.g. during the soft-start phase or when all the channels are set to 0% brightness), the current generators are off and there is no useful information coming from them. therefore the output voltage is regulated to the minimum value ( equation 2: ). it must be ensured that the minimum output voltage is below the minimum expected output voltage table 9. handshake signals summary pin function iok used by the slaves to increase the output voltage (algorithm is overdriven) xvok used by the slaves to ask for an output voltage reduction xovf used by the master to inform that the maximum output voltage has been reached (each slave uses this information to tag as ?faulty? its open channels) xmsk used by the master to inform the slaves that the output voltage is out of regulation and the led fault detection must be masked to prevent false detection v boost min , r 1 r 2 + r 1 -------------------- ?? ?? v vfb min , ? = v boost max , r 1 r 2 + r 1 -------------------- ?? ?? v vfb max , ? = recommended operating conditions led7708 24/53 doc id 022698 rev 1 in order to guarantee enough steering room for the optimization. because of the significant dependence of the led forward voltage with temperature, this must be taken into account when calculating the minimum expected output voltage. the best way to proceed when designing the external components is the following: 1. determine the output voltage range required by the led strings, considering v f spread and temperature variation: 2. calculate the middle-point of the output voltage range v boost,middle . 3. calculate the output divider through equation 4 and 5 . 4. calculate the resulting four output voltage ranges (vmin setting options). 5. select the output voltage range closest to the one calculated at point 1. equation 4 equation 5 8.3.2 boost converter loop the voltage drop of each current generator is sent to the minimum voltage selector: the lowest one is used as feedback and sent to the window comparator, whose outputs are used to increase or decrease the loop-counter. the digital outputs of the counter are connected to the dac and the target reference is generated. as previously mentioned, this reference voltage is compared to a partition of the output voltage: the difference is translated into an error current at the output of the trans-conductance amplifier (see figure 4 , comp pin). at this point the compensation network, externally connected to the comp pin, provides the programmed trip level for the inductor current. an additional slope compensation ramp is mixed, as usual, to avoid possible sub-harmonic instability when the boost converter operates in continuous conduction mode (ccm). the slope pin allows the proper setting of the amount of slope compensation connecting a simple resistor rslope between the slope pin and ground. the compensation ramp of a master device starts at 35% (typ.) of each switching period. the boost converter switching frequency can be set in the 200 khz-1 mhz range by connecting the fsw pin to ground through a resistor, calculated according to equation 6 : equation 6 ) v ( max = v j f, m 1 = j n 1 = i led le ds ro w s r 2 v boost middle , v vfb ? () v vfb --------------------------------------------------------------- r 1 ? = v boost max , r 1 r + 2 --------------------------------- - 100 a sw f fsw f k r = led7708 recommended operating conditions doc id 022698 rev 1 25/53 in addition, when the fsw pin is tied to ldo3, the led7708 uses a default 610 khz fixed switching frequency, allowing the saving of a resistor in minimum component-count applications. the fsw pin can also be used as synchronization input, allowing the led7708 to operate both as master or slave device. if a clock signal having a frequency within the capture range is applied to this pin, the device locks synchronized. the minimum pulse width which allows the synchronizing pulses to be detected is 270 ns (typ.). the sync pin is a synchronization output and provides a 35% (typ.) duty cycle clock when the led7708 is set as master or a replica of the fsw pin when it is set as slave. it is used to connect multiple devices in a daisy chain configuration or to synchronize other switching converters running in the system with the led7708. when an external synchronization clock is applied to the fsw pin, the internal oscillator is overdriven and the external power mosfet is ignited on the rising edge of the synchronization signal while the slope compensation ramp starts on the falling edge of the same signal. for this reason, the duty cycle of the external synchronization clock should be 30% to 40% to prevent sub-harmonic instability when the boost converter is working in continuous-conduction mode (ccm). 8.3.3 slope compensation the constant frequency, peak current-mode topology has the advantage of very easy loop compensation with output ceramic caps (reduced cost and size of the application) and fast transient response. in addition, the intrinsic peak current measurement simplifies the current limit protection, avoiding undesired saturation of the inductor. on the other side, this topology has a drawback: there is inherent open loop instability when operating with a duty cycle greater than 0.5. this phenomenon is known as ?sub-harmonic instability? and can be avoided by adding an external ramp to the one coming from the sensed current. this compensating technique, based on the additional ramp, is called ?slope compensation?. as seen in figure 6 , when the switching duty cycle is higher than 0.5, the small perturbation il dies away in subsequent cycles thanks to the slope compensation and the system reverts to a stable situation. recommended operating conditions led7708 26/53 doc id 022698 rev 1 figure 6. effect of slope compensation on small inductor current perturbation (d>0.5) the slope pin allows to properly set the amount of slope compensation connecting a simple resistor r slope between the slope pin and the output. the compensation ramp starts at 35% (typ.) of each switching period and its slope is given by the following equation: equation 7 where k s = 4.0 s -1 and s e is the slope ramp in [a/s]. to avoid sub-harmonic instability, the compensating slope should be at least half the slope of the inductor current during the off-phase when the duty cycle is greater than 50%. the value of r slope can be calculated according to equation 8 . equation 8 8.3.4 external mosfet control the led7708 employs an external mosfet as the power switch for the boost converter. the internal gate driver is capable of sourcing and sinking up to 1 a and it is supplied through the vdr pin, internally connected to the +5 v ldo. a 1 f decoupling capacitor, connected between the vdr pin and pgnd, is highly recommended. when an external +5 v supply is available, the whole device can be supplied by connecting both the vdr and vin pins to this rail. ! - v 4 3 7 0 r o g r a m m e d i n d u c t o r p e a k c u r r e n t w i t h s l o p e c o m p e n s a t i o n 3 % ) n d u c t o r c u r r e n t # # - t ) " / / 3 4 0 % ! + q 4 3 7 ? ) , ) n d u c t o r c u r r e n t p e r t u r b a t i o n 4 3 7 0 r o g r a m m e d i n d u c t o r p e a k c u r r e n t w i t h s l o p e c o m p e n s a t i o n 3 % ) n d u c t o r c u r r e n t # # - t ) " / / 3 4 0 % ! + q 4 3 7 ) , ) n d u c t o r c u r r e n t p e r t u r b a t i o n s e k s r slope --------------------- = r slope 2k s lv out v in ? 0.7v ? () ??? v out v in ? () ---------------------------------------------------------------------------------------- led7708 recommended operating conditions doc id 022698 rev 1 27/53 detailed information about the mosfet gate driver can be found in section 5: electrical characteristics . the current flowing through the power mosfet is sensed during the on-phase by measuring the voltage drop across an external sensing resistor (connected between the source of the mosfet and pgnd). the overcurrent condition is detected by comparing the sensed voltage with an internal threshold. this threshold can be set in the 100 mv - 300 mv range according to the resistor connected between the clim pin and ground. the sensing resistors are often available in few values: once a suitable one has been selected, the resistor at the clim pin is calculated according to the following equation: equation 9 where k c1 = 1.63 x 10 -5 v and k c2 = 3.1 x 10 -2 a. the maximum allowed peak current depends on the external mosfet capability. the actual maximum peak current is given by the above equations as long as duty cycle is below 35% and decreases as duty cycle increases beyond 35%, depending on the slope compensation setting. if an overcurrent (oc) condition occurs, the boost controller turns-off the external mosfet and skips subsequent switching cycles until the current is above the programmed level. in the case of a light load condition, the comp pin voltage may fall below 0.8 v (typ.). in this case the boost controller stops switching until the error amplifier forces the comp voltage to rise. the above voltage at the comp pin corresponds to about 25% of full current limit. in a boost converter, the rms current through the internal mosfet depends on both the input and output voltages, according to equation 10 (dcm) and 11 (ccm). equation 10 equation 11 the current limitation works by clamping the comp pin voltage proportionally to r bilim . the peak inductor current is limited to the above threshold decreased by the slope compensation contribution. 8.4 current generators section the led-driving section consists of 16 current generators connected to the internal control logic. each channel can sustain up to 40 v and sink up to 85 ma. the brightness of the leds connected to the led7708 is controlled by switching the current between a maximum value (on-phase) and a minimum one (off-phase) at a given dimming frequency (pwm control). r clim r sns i mos ocp , k c2 + ? () k c1 --------------------------------------------------------------------- = i mos rms , v in d ? f sw l ? --------------------- - d 3 --- - = () () () ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? + ? = 3 2 sw out out 2 out rms , mos d 1 d l f i v 12 1 d 1 d i i recommended operating conditions led7708 28/53 doc id 022698 rev 1 the two current levels are set by connecting a resistor on both the iseth and isetl pins: equation 12 where k h = 1200 v. equation 13 where k l = 4.0 v. the lower level is generally used to keep the voltage across the led string under control during the off-phase of the dimming period; if a zero-current low level is required, the isetl pin must be connected to the device supply rail (ldo3). the current generators of the led7708 have been designed to be grouped (i.e. connected in parallel) if required by the application. for stability reasons, the parallelization of the current generators should be done when the programmed current is above 40 ma per channel. the current accuracy among different devices is guaranteed to be lower than 2% through the full output current range (20 ma-85 ma). two current ranges are selectable in order to optimize the overall current accuracy. ta b l e 1 0 provides some typical output currents for standard e96 values. unused channels should be disabled through the chsel register and can be physically left floating or shorted to ground. table 10. led current vs. external resistor setting nominal led current i chx,on [ma] r iseth [k ? ] e96 series (1%) actual led current i chx,on [ma] 85 14.3 83.9 75 16.2 74.1 60 20.0 60.0 50 24.3 49.4 40 30.1 39.9 30 40.2 29.9 20 60.4 19.9 15 80.6 14.9 i chx on , k h r iseth ------------------- = i chx off , k l r isetl ------------------ = led7708 recommended operating conditions doc id 022698 rev 1 29/53 8.5 serial interface 8.5.1 serial interface architecture the led7708 is equipped with a 4-wire serial interface (si) to allow full control of its functionalities by the host controller. the led7708 uses four pins (din, dout, dclk and le) to connect itself to the serial bus. the serial interface supports a data clock frequency up to 30 mhz. figure 7. simplified serial interface block diagram 8.5.2 serial interface internal registers the internal registers are organized in control registers and brightness registers. access to the desired register is performed by encoding the destination address via a serial key on the bus (a serial key consists of a certain number of clock pulses during the high-state of the le signal). all the internal registers are 16 bits wide. ! - v " 2 4 " 2 4 # ( 3 4 ! # ( 3 % , $ % 6 # & ' ' r a y s c a l e 3 y n c b i t b u f f e r # / 5 . 4 % 2 # / - 0 # / - 0 $ ) . $ / 5 4 $ # , + , % ' 3 # ' 3 3 9 $ % 6 # & ' b i t & ) & / b i t & ) & / 3 e r i a l + e y $ e c o d e r # ( 3 % , # ( 3 % , # ( 3 % , # ( 3 % , f r o m % r r o r $ e t e c t i o n # i r c u i t r y 4 o # u r r e n t ' e n e r a t o r 4 o # u r r e n t ' e n e r a t o r 4 o # o n t r o l , o g i c ' 3 , ! 4 " 5 & & % 2 " # , + " 5 & & % 2 " , % table 11. internal registers control registers brightness registers devcfg0 devcfg1 gslat chsta chsel brt01 to brt16 recommended operating conditions led7708 30/53 doc id 022698 rev 1 8.5.3 internal registers access the led7708 is capable of supporting different data formats to satisfy different application needs. the control registers are accessed one at a time by using 16-bit read/write operations, while the brightness registers can be loaded in sequence (16x16-bit) or in a single shot (1x256-bit). an additional data format (1x192-bit) allows data flow optimization when only 12 bits are used for brightness control. after the startup sequence, the 16x16-bit data format is set by default. figure 8 details the signal timing for a write operation to the devcfgx registers. ta b l e 1 2 summarizes the available operations: figure 8. timing diagram related to a devcfgx write operation table 12. internal register operations encoding dclk rising edges with le=1 operation 1 data latch (brtxx) 2-3 global latch (brtxx) 4-5 write chsel 6-7 read chsta 8-9 write devcfgx(*) 10-11 read devcfgx (1) 1. the content of the shift register is loaded into devc fg0 or devcfg1 according to the dest bit (the most significant bit, common to both registers). the data bits are shifted in starting from the most significant one (msb first). 12-13 write gslat ! - v % & # ! " $ $ # , + $ ) . , % b i t d a t a led7708 recommended operating conditions doc id 022698 rev 1 31/53 8.5.4 brightness data formats the format for the brightness data is chosen by acting on the bdfs (brightness data format selector) and the brls (brightness register length selector) bits of the devcfg1 register. 16x16-bit data format (bdfs=0, brls=x) the brightness registers brt01:brt16 are sequentially loaded at the end of 16-bit write operations. the le is managed to encode two serial keys: one for the so called ?data latch? operation and another to encode the final ?global latch? operation. therefore, a complete brightness data transfer to the led7708 consists of 15 ?data latch? operations followed by a single ?global latch? operation. if the 4096 steps (12-bit) brightness control is used (brls low), the four most significant bits of each brightness register are unused. the brightness registers are written from brt16 to brt01 with auto-decrement after each write operation (the le signal of the last write operation to brt01 must encode a ?global latch?). figure 9. 16-bit data format, write operation to the brightness register table 13. brightness data formats bdfs brls brightness data format 00 16x16, 12-bit (the 4 most significant bits are not used) 0 1 16x16, 16-bit 1 0 192x1, 12-bit 1 1 256x1, 16-bit ! - v % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 e l w % u l j k w q h v v ' d w d 6 w u h d p ( ) & $ % ' ' & / . ' , 1 / ( e l w ' d w d 3 d f n h w ' d w d / d w f k recommended operating conditions led7708 32/53 doc id 022698 rev 1 1x256-bit data format (bdfs=1, brls=1) this option allows a complete brightness data transfer in a single 256-bit write operation. the brightness registers brt01:brt16 are simultaneously loaded at the falling edge of the le signal. only 65536 steps (16-bit) brightness control is supported by this data format. figure 10. 256-bit data format, write operation to the brightness registers 1x192-bit data format (bdfs=1, brls=0) the brightness registers brt01:brt16 are simultaneously loaded at the end of a single 192-bit single write operation. this option is similar to the 1x256-bit format but optimizes the serial bus communication when 12 bits only are used for the brightness control. figure 11. 192-bit data format, write operation to the brightness registers ! - v % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 e l w % u l j k w q h v v ' d w d 6 w u h d p ) ( ) ) ) & ) $ ) % ) ' ) ' & / . ' , 1 / ( e l w ' d w d 3 d f n h w * o r e d o / d w f k ! - v % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 % 5 7 e l w % u l j k w q h v v ' d w d 6 w u h d p % ( % ) % & % $ % % % ' % ' & / . ' , 1 / ( e l w ' d w d * o r e d o / d w f k led7708 recommended operating conditions doc id 022698 rev 1 33/53 normally, the serial data coming from the din pin is clocked out at the dout pin. optionally, the led7708 can continuously transmit the status of the control registers when the continuous status reading (csrd) bit of the devcfg0 register is asserted. in this case the device replaces (with a 16-clock-cycle delay) the received brightness data stored in the fifo with the chsta, chsel, latency, devcfg0 and devcfg1 content. this option is useful to get the device status without interrupting the brightness data flow. the continuous status reading is available only with 1x256-bit and 1x192-bit data formats. see section 8.8.2 for details. 8.5.5 brightness registers (brtxx) the brt16:01 registers are 16-bit wide, write-only registers where the brightness levels, received through the serial interface, are stored. these registers may be 12 or 16 bits wide, depending on the brls and bdfs bits of the devcfg1, see ta b l e 1 5 . the led7708 supports two brightness control options: group dimming and grayscale dimming. the first option uses brt01 only to set the desired brightness to all the channels, while the second one allows independent brightness level on each channel (all brtxx registers are used). group dimming and grayscale dimming modes are selected through the gsme bit of the devcfg0 register. the pwm signals at the outputs are generated by comparing the content of the brt16:01 registers to a 16-bit or 12-bit counter, according to brls and bdfs bit status. the clock source for the counter can be either external or internal, depending on the fosc pin status. see section 8.6.1: internal dimming oscillator for details. all the brightness registers are not directly connected to the digital comparators of the grayscale circuitry: a 256-bit buffer is used to store the value. the content of the buffer is transferred to the brightness registers at the end of the le pulse (falling edge) or at the end of the current dimming cycle according to the selected option (see the dass bit of the devcfg1 register for details). 8.5.6 devcfg0 register table 14. devcfg0 register bit position attribute default description den 0 r/w 0 device enable 0= device off 1= device on edmi 1 read only 1 error detection mode indicator 0= valid data on chsta 1= error detection in progress or output voltage not optimized ovfw 2 read only 0 regulation dac overflow 0= regulation dac in range 1= regulation dac overflow otaf 3 read only 0 overtemperature alert flag 0= die temp <120 c 1= die temp >130 c recommended operating conditions led7708 34/53 doc id 022698 rev 1 warning: (?) in order to prevent damage to the device or to the external circuitry, these bits are locked when the den bit of devcfg0 is asserted. ocad 4 r/w 0 open channel auto disconnection 0= open channels not disconnected 1= open channels auto-disconnection scad 5 r/w 0 shorted channel auto disconnection 0= shorted channels not disconnected 1= shorted channels auto-disconnection cfp 6 read only 0 critical fault protection 0= no protection occurred 1= ov or ot protection occurred rwas 7 r/w 0 regulation window amplitude selection 0= 300 mv regulation window 1= 600 mv regulation window dts0 8 r/w 0 led short detection threshold selection (see ta bl e 1 7 ). dts1 9 r/w 0 gsme 10 r/w 0 grayscale mode enable 0= group dimming mode 1= grayscale dimming mode crs? 11 r/w 0 current range selector? 0= lower current range (20 ma-45 ma) 1= upper current range (40 ma-85 ma) ovrs 12 read only 0 output voltage regulation status 0= output voltage not optimized 1= output voltage optimized ovre 13 r/w 0 output voltage regulation enable 0= output voltage regulation disabled 1= output voltage regulation enabled sdms? 14 r/w 0 slave device mode selection? 0= no slave devices 1= slave devices connected dest 15 r/w x destination register address 0= fifo loaded into devcfg0 1= fifo loaded into devcfg1 table 14. devcfg0 register (continued) bit position attribute default description led7708 recommended operating conditions doc id 022698 rev 1 35/53 8.5.7 devcfg1 register table 15. devcfg1 register bit position attribute default description adj0 0 r/w 0 current gain adjust adj1 1 r/w 0 adj2 2 r/w 0 adj3 3 r/w 0 adj4 4 r/w 0 adj5 5 r/w 0 cgrs 6 r/w 1 current gain range selector 0= range 1 selected 1= range 2 selected see section 8.8.1: current generators gain adjust . lat16 7 r/w 0 bits #16 and #17 of dimming latency (see gslat register) lat17 8 r/w 0 bdfs 9 r/w 0 brightness data format selector 0= 16x16-bit format 1= 1x256-bit or 1x192-bit format brls 10 r/w 0 brightness registers length selector 0= 12-bit resolution 1= 16-bit resolution dtin 11 r/w 0 dimming timing inversion selector 0= dimming cycle off-phase first 1= dimming cycle on-phase first dass 12 r/w 0 data synchronization selector 0= brightness data immediately updated at the falling edge of le 1= brightness data updated at the end of the current dimming cycle dsys? 13 r/w 0 dimming synchronization selector? 0= gssy pin is pulse output 1= gssy pin is trigger input csrd 14 r/w 0 continuous status reading 0= continuous status reading disabled 1= continuous status reading enabled dest 15 r/w x destination register address 0= fifo loaded into devcfg0 1= fifo loaded into devcfg1 recommended operating conditions led7708 36/53 doc id 022698 rev 1 warning: in order to prevent damage to the device or to the external circuitry, these bits are locked when the den bit of devcfg0 is asserted. 8.5.8 gslat register the latency is used to insert a programmable delay at the beginning of each dimming period to implement a certain amount of scanning. the scanning technique is basically a way to improve the dynamic performance of an lcd panel by powering the backlight only when the pixels are stable. the gslat register is a write-only register and stores the 16 less significant bits of the dimming period latency. the additional two most significant bits are located in the devcfg1 register (lat16 and lat17 bits). thanks to the 18-bit wide latency, the led7708 is capable of supporting down to 20% of scanning waveform (see section 8.6: dimming options for details). table 16. available led short detection thresholds dts1 dts0 led short-circuit detection threshold 0 0 led short detection disabled 0 1 led short detection threshold fixed to 3.4 v 1 0 led short detection threshold fixed to 6.8 v 1 1 led short detection threshold fixed to 8.4 v led7708 recommended operating conditions doc id 022698 rev 1 37/53 8.5.9 chsel register the chsel register is a readable/writable configuration register. every bit of this register allows the user to enable/disable the channels. independent control of the channels (e.g. scrolling backlight or phase shift) can be achieved by acting on this register. 8.5.10 chsta register the chsta register is a read only status register. each bit of this register shows the status of the corresponding channel. after the error detection sequence takes place, the channels which have an excessive voltage drop (led short-circuit) or that are unable to regulate the nominal current (open channels) are tagged as faulty and the related chsta bits are asserted. the chsel register is not affected by the error detection sequence. the channels disabled by clearing the corresponding bits of the chsel register are not involved in the error detection and the corresponding bits of the chsta register are forced low. the chsta register is automatically overwritten during subsequent error detection occurrences. table 17. chsel register bit position attribute meaning chsel0 to chsel15 0 r/w 1= the corresponding channel is active. 0= the corresponding channel is disabled. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 recommended operating conditions led7708 38/53 doc id 022698 rev 1 if at least one bit of the chsta register is asserted after the error detection sequence, the xflt pin is tied low. both the chsta register and the xflt pin are reset by clearing the den bit of devcfg0 or by performing a por. 8.5.11 internal registers initialization the internal registers show the following configuration after a por. table 18. chsta register bit position attribute meaning chsta0 to chsta15 0 read only 0= the channel is working properly or is not used (the corresponding chsel bit is cleared) 1= the channel is open or an led short-circuit has been detected during the error detection sequence 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 table 19. default configuration of internal registers after por register value (binary) devcfg0 0000 0000 0000 0010 devcfg1 0000 0000 0100 0000 gslat 0000 0000 0000 0000 brtxx 0000 0000 0000 0000 chsel 0000 0000 0000 0000 chsta 0000 0000 0000 0000 led7708 recommended operating conditions doc id 022698 rev 1 39/53 the content of the internal registers, except the read-only bits of devcfg0 and devcfg1 (i.e. cfp, ovrs, ovfw and edmi), is not affected when the den bit is cleared. warning: in order to prevent damage to the device or to the external circuitry, some bits of devcfg0 and devcfg1 registers (crs, sdms and dsys) are locked when den is high. 8.6 dimming options the brightness of the leds connected to the output channels can be basically controlled in two ways, depending on the status of the gsme bit of the devcfg1 register: group dimming mode (gsme=0): common dimming performed by using the brightness value received through the serial interface and stored in the brt01 register: all the channels have the same pwm duty cycle; grayscale dimming mode (gsme=1): independent pwm dimming on each channel performed by loading the brt01:brt16 brightness registers. in practice, a third way to control the brightness of the leds should rely on an intensive use of the chsel register by the host controller. the direct control of the chsel register, combined with either the group dimming or the grayscale dimming, allows the user to implement particular dimming algorithms. once the dimming control mode has been chosen through the gsme bit, the source of the clock for the pwm generation (grayscale clock) must be selected. the led7708 can use either an external clock source or its internal high-frequency oscillator. 8.6.1 internal dimming oscillator the led7708 has a programmable oscillator dedicated to the dimming circuitry. the output clock is provided at the gsck pin for the slave devices. if the fosc pin is forced high, the oscillator is turned off and the gsck pin becomes the grayscale clock input. the oscillator frequency is simply set by connecting a resistor between the fosc pin and ground: equation 14 table 20. fosc pin setting options fosc pin setting oscillator gsck pin function high (to ldo3) off grayscale clock input resistor to gnd active (4 mhz-25 mhz) grayscale clock output fosc osc gsck r k f = recommended operating conditions led7708 40/53 doc id 022698 rev 1 equation 15 figure 12. dimming signals and synchronization table 21. function of pins involved in dimming control pin function gsck input or output, depending on fosc pin status; fosc high: grayscale clock input, internal oscillator disabled. fosc to resistor: grayscale clock output. the clock, internally generated by the dimming oscillator, is provided at this pin. fosc internal oscillator frequency setting. see above. gssy input or output pin, depending on dsys bit value. used for dimming synchronization. see ta bl e 2 1 . table 22. dimming synchronization control dsys dimming sync selector (locked if den is asserted) 0 the gssy pin is set as output and provides a pulse at the end of each dimming cycle. the device continuously performs a latency+dimming sequence. 1 the gssy pin is set as input. the ongoing dimming sequence is reset as soon as a rising edge on the gssy input is detected; a new latency+dimming cycle is triggered by the falling edge on this pin. n osc dim 2 f f = ! - v 3 y n c h r o n i z a t i o n o f d i m m i n g c y c l e s i s p e r f o r m e d t h r o u g h ' 3 3 9 p i n s ' 3 # + ' 3 # + & / 3 # & / 3 # ' 3 3 9 ' 3 3 9 - a s t e r a n d s l a v e d e v i c e s u s e t h e s a m e e x t e r n a l ' r a y s c a l e # l o c k ' 3 # + 3 y n c h r o n i z a t i o n o f d i m m i n g c y c l e s i s p e r f o r m e d t h r o u g h ' 3 3 9 p i n s ' 3 # + ' 3 # + & / 3 # & / 3 # ' 3 3 9 ' 3 3 9 4 h e s l a v e d e v i c e s u s e t h e ' r a y s c a l e # l o c k ' 3 # + g e n e r a t e d b y t h e m a s t e r o s c i l l a t o r led7708 recommended operating conditions doc id 022698 rev 1 41/53 8.6.2 dimming waveforms normal dimming mode in normal timing mode the basic cycle is represented by a latency period followed by a dimming period starting with the on-phase (current generators active). this option is selected by clearing the dtin (dimming timing inversion) bit of the devcgf1 register. figure 13. normal timing mode waveforms inverted dimming mode in inverted dimming mode, the basic cycle is represented by a latency period followed by a dimming period starting with the off-phase (current generators turned off). this option, normally used when a common turn-off is required, is selected by asserting the dtin (dimming timing inversion) bit of the devcgf1 register. figure 14. inverted timing mode waveforms ! - v , a t e n c y 4 o f f 4 o n & i x e d o r g r a y s c a l e c l o c k c y c l e s 5 p t o g r a y s c a l e c l o c k c y c l e s $ i m m i n g p e r i o d ! - v / d w h q f \ 7 r q 7 r i i ) l [ h g r u j u d \ v f d o h f o r f n f \ f o h v 8 s w r j u d \ v f d o h f o r f n f \ f o h v ' l p p l q j s h u l r g recommended operating conditions led7708 42/53 doc id 022698 rev 1 8.6.3 grayscale synchronization grayscale sync (gssy) used as synchronization output when the dsys bit of the devcfg1 register is set low, the gssy pin of the led7708 is set as output. a 4xt gsc high level pulse is provided at the gssy pin at the end of each dimming cycle (latency followed by a dimming period). figure 15. dimming waveform and gssy output pulse grayscale sync (gssy) used as synchronization input when the dsys bit of the devcfg1 register is set high, the gssy pin of the led7708 is set as input. this option can be used to lock the dimming cycles (latency followed by a dimming period) to the vertical sync signal (vsync) coming from the video processor. the minimum pulse duration is 2xt gsc . as soon as the gssy signal goes high, the ongoing dimming sequence is stopped and the grayscale counter is reset. a new dimming sequence is triggered when the gssy pin goes low. figure 16. dimming waveform triggered by gssy input ! - v , a t e n c y 4 o f f 4 o n & i x e d o r g r a y s c a l e c l o c k c y c l e s 5 p t o g r a y s c a l e c l o c k c y c l e s $ i m m i n g p e r i o d x 4 ' 3 # ' 3 # + # ( x c u r r e n t ' 3 3 9 ! ' 3 3 9 p u l s e i s g e n e r a t e d a t t h e e n d o f e a c h , a t e n c y $ i m m i n g p e r i o d s e q u e n c e ! - v , a t e n c y 4 o f f 4 o n & i x e d o r g r a y s c a l e c l o c k c y c l e s 5 p t o g r a y s c a l e c l o c k c y c l e s $ i m m i n g p e r i o d 4 h e f a l l i n g e d g e o f t h e ' 3 3 9 s i g n a l t r i g g e r s a n e w d i m m i n g s e q u e n c e ' 3 # + # ( x c u r r e n t ' 3 3 9 4 h e r i s i n g e d g e o f t h e ' 3 3 9 s i g n a l s t o p s t h e d i m m i n g s e q u e n c e a n d r e s e t s t h e g r a y s c a l e c o u n t e r led7708 recommended operating conditions doc id 022698 rev 1 43/53 8.7 fault management the led7708 includes some protection to prevent damage to itself and to the backlight. in order to satisfy these requirements, the following protection has been implemented: the xflt pin is an open drain output (active low) and is affected by the following faulty conditions: figure 17. internal signals connected to the xflt pin 8.7.1 overvoltage protection the led7708 protects itself and the external components from excessive output voltage by monitoring the voltage at the vfb pin. the overvoltage threshold is given by the following equation, where r1 and r2 are the resistors of the output divider: table 23. detected faulty conditions faulty condition involved section boost output overvoltage (ov) boost controller external mosfet overcurrent (oc) open channel current generators excessive channel voltage (led short-circuit) overtemperature protection whole device table 24. xfault pin behavior detected fault involved flag xflt status overvoltage protection ovpf low overtemperature alert otaf low open channel chsta16:chsta01 low led short-circuit chsta16:chsta01 low ! - v ' 7 6 ' 7 6 2 s h q f k d q q h o & ) 3 2 7 $ ) / ( ' v k r u w f l u f x l w ; ) / 7 recommended operating conditions led7708 44/53 doc id 022698 rev 1 equation 16 once the voltage at the vfb pin has crossed the related threshold, the led7708 shuts down, the cfp (critical fault protection) flag of the devcfg0 register is asserted, the xflt pin is set low and the condition is latched. normal operation is restored by toggling the den bit of the devcfg0 register or by performing a por. 8.7.2 overtemperature alert and thermal protection the led7708 implements a two-level thermal protection. when the junction temperature rises above 130 c (typ.), the overtemperature alert flag (otaf) is asserted and the xflt pin goes low. the otaf flag is cleared as soon as the chip temperature drops below 125 c (typ.). this bit is used by the host controller to enable output voltage regulation if temporarily disabled. if the temperature of the chip crosses 150 c, the device shuts down. automatic restart occurs as soon as the temperature drops to 130 c. 8.7.3 overcurrent protection overcurrent occurring in the power mosfet is managed by skipping subsequent switching cycles until the faulty condition is present. the xflt pin is not affected. see also section 8.3.3 for details. 8.7.4 led short-circuit and open channel faults the faults that can occur to the current generators section are basically the following: one or more open (floating) channels excessive voltage drop (shorted leds). the led7708 manages these faulty conditions following a particular algorithm. when a channel opens, its voltage drop falls to zero: the output voltage regulation circuitry tags it as ?probably faulty? and increases the output voltage. if the ?open? condition is temporary, the voltage drop across the generator is self-recovered and the output voltage is corrected. in case of a real open channel, the regulation dac reaches the maximum value (dac overflow) and the ovfw bit of the devcfg0 register is asserted. the led7708 can automatically disconnect the open channels if required. therefore, if the open channels auto-disconnection (ocad) bit of the devcfg0 register is asserted, the faulty channel is suddenly turned off, excluded from the regulation loop and the output voltage is quickly adjusted to the optimal level. during the open channel detection (i.e. when the regulation dac is rolling up), the led short-circuit detection circuitry is masked to avoid false detection due to the high output voltage. if the ocad bit is cleared, the output voltage is kept to the maximum value and the fault management is demanded to the host controller (xflt pin low). in case of led short-circuit, the voltage across the related channel increases. the led7708 compares the drop across each channel with a fixed threshold in order to detect this v out ovp , r 1 r 2 + r 2 -------------------- v fb ov , ? = led7708 recommended operating conditions doc id 022698 rev 1 45/53 condition. four options can be chosen by acting on the dts1:dts0 bits of the devcfg0 register (see ta b l e 1 6 ). to prevent false triggering, the led short-circuit detection is masked if the output voltage is out of regulation (i.e. the ovrs bit of the devcfg0 is low). each channel detected as faulty (open or shorted) sets the corresponding bit of the chsta register. the fault management algorithm can operate only if the channels are active and at a minimum (10 s typ.) pwm on-time is required at the outputs in order to detect the faulty condition. after the detection of a ?probably open channel?, the device begins to ramp-up the output voltage, but this operation cannot be performed if the involved channel is turned off (no feedback information available). in this case, the algorithm should wait until the channel is turned on again, leading to a delayed output voltage steering because of the dimming function. this situation can induce excessive power dissipation on the other channels (high- voltage drop for a long period). to prevent this, the led7708 automatically forces the ?probably open channel? to remain on (regardless of its programmed status) until the maximum output voltage has been reached (confirmation of open channel fault) or the output current has been recovered. once the algorithm has recognized the open condition, the faulty channel is excluded from the regulation loop and the output voltage is quickly decreased to the optimal value in order to avoid excessive power dissipation (only if the ocad bit is asserted). therefore, the open channel/led-short fault detection algorithm can operate in a transparent way without the need to stop the dimming function. 8.8 special function 8.8.1 current generators gain adjust the gain of the current generators can be varied by changing the adj5:adj0 bits of the devcfg1 register (64 steps). two selectable ranges are provided by asserting/clearing the current gain range selector (cgrs) bit of the devcfg1 register. after por, the current gain is unitary and can be changed according to the following formulas: equation 17 equation 18 equation 19 g cgrs 1 = 1g d 0.5 64 ------- - ? + = g cgrs 0 = 0.75 g d 0.25 64 ----------- ? + = g d adj5x2 5 adj4x2 4 adj3x2 2 adj2x2 2 adj1x2 adj0 +++++ = recommended operating conditions led7708 46/53 doc id 022698 rev 1 figure 18. channels current gain adjust 8.8.2 continuous status reading the continuous status-reading is a feature that allows the content of the internal registers to be obtained without stopping the brightness data flow. the content of the devcfg0, devcfg1, chsel, chsta and gslat is automatically loaded into the fifo after the brightness data has been moved to the buffer. this feature is supported in 1x1256-bit and 1x192-bit data formats only. figure 19. continuous reading mode disabled, 1x256-bit data format ! - v 6 w h s v & * 5 6 6 w h s v & * 5 6 * * * ! - v b i t " r i g h t n e s s $ a t a 3 t r e a m . . b i t b r i g h t n e s s d a t a 0 r e v i o u s $ a t a 3 t r e a m . . . . . . . . . $ ) . , % $ / 5 4 led7708 recommended operating conditions doc id 022698 rev 1 47/53 figure 20. continuous reading mode enabled, 1x256-bit data format ! - v b i t " r i g h t n e s s $ a t a 3 t r e a m . . b i t b r i g h t n e s s d a t a d u m m y 0 r e v i o u s 2 e g i s t e r s # o n f i g u r a t i o n $ % 6 # & ' $ % 6 # & ' d u m m y ' 3 , ! 4 # ( 3 % , # ( 3 4 ! . . . . . . . . d u m m y d u m m y d u m m y $ ) . , % $ / 5 4 package mechanical data led7708 48/53 doc id 022698 rev 1 9 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack specifications, grade definitions and product status are available at: www.st.com . ecopack is an st trademark. led7708 package mechanical data doc id 022698 rev 1 49/53 table 25. vfqfpn48 (7 x 7 x 1.0 mm.) package mechanical data dim. (mm.) min. typ. max. a 0.80 0.90 1.00 a1 0.02 0.05 a2 0.65 1.00 a3 0.25 b 0.18 0.23 0.30 d 6.85 7.00 7.15 d2 4.95 5.10 5.25 e 6.85 7.00 7.15 e2 4.95 5.10 5.25 e 0.45 0.50 0.55 l 0.30 0.40 0.50 ddd 0.08 package mechanical data led7708 50/53 doc id 022698 rev 1 figure 21. vfqfpn48 (7 x 7 x 1.0 mm.) package outline led7708 package mechanical data doc id 022698 rev 1 51/53 figure 22. recommended pcb footprint am111 3 7v1 8 .60 1.20 0.50 0.2 8 5.00 revision history led7708 52/53 doc id 022698 rev 1 10 revision history table 26. document revision history date revision changes 07-may-2012 1 initial release. led7708 doc id 022698 rev 1 53/53 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by two authorized st representatives, st products are not recommended, authorized or warranted for use in military, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or register ed trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2012 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com |
Price & Availability of LED7708TR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |