View IRMD2336DJ_8837628.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

24 july 2008 rev 1.3 ? 2 008 international rectifier data sheet no. pd60358 IRMD2336DJ 3 phase gate driver ic reference design kit irs2336dj gate driver ic features drives up to six igbt/mosfet power devices gate drive supplies up to 20 v per channel integrated bootstrap functionality over-current protection over-temperature shutdown input advanced input filter integrated deadtime protection shoot-through (cross-conduction) protection under voltage lockout for v cc & v bs enable/disable input and fault reporting adjustable fault clear timing separate logic and power grounds 3.3 v input logic compatible tolerant to negative transient voltage designed for use with bootstrap power supplies matched propagation delays for all channels reference design features complete 3-phase ac motor drive system to showcase irs2336dj gate driver ic operation no extra hardware needed for pwm signal generation; option to incorporate external pwm signals to drive irs2336dj if desired gui software for running induction motor in open loop volts-per-hertz mode of operation discrete igbt power stage for maximum flexibility o igbt?s rated for 10a @100 o c o short circuit rating 10 s o to220 full-pak package conveniently located test points for irs2336dj signal monitoring product summary ac input voltage (typ.) 220 v rms continuous motor current 3 a rms dv/dt 5 kv/ s continuous output power 400 w overview the IRMD2336DJ is a reference design kit for the ir s2336dj three phase gate driver ic with integrated bootstrap functionality. the design kit includes a complete d rive system board with an input rectifier, control power supplies, digital motor control ic and power inverter. safety features include protections against motor line-to -line and line- to-dc bus(-) short situations. the power stage fea tures the irs2336dj gate driver and six discrete ig bt power switches allowing for easy customization. the inclu ded pc based gui software allows the user to drive an induction motor in open-loop volts-per-hertz mode o f operation using the on-board digital control ic. the motor speed and system parameters such as pwm frequency a nd deadtime can be modified using the gui. alternat ely, the irs2336dj gate drive input pwm signals can be s upplied externally by patching in signals through a n on- board connector. downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 2 table of contents safety precautions????????????????????????????????? ?????.4 IRMD2336DJ hardware description???????????????????? ????????..........6 top level description?????????????????????????????? ??????6 irs2336dj gate driver ic??????????????????????????? ???????7 bootstrap supply??????????????????????????????????? ???8 gate drive resistors??????????????????????????????? ?????.8 IRMD2336DJ protection features????????????????????? ????????.....9 IRMD2336DJ fault reporting????????????????????????? ??????.....9 automatic reset after itrip fault?????????????????? ????????????..9 IRMD2336DJ enable function????????????????????????? ????.??.10 pwm input to irs2336dj & connection of an external system controller?????????????.10 test points for investigation?????????????????????? ??????????...11 IRMD2336DJ operating instructions?????????????????? ????????????12 software installation?????????????????????????????? ??????.12 test bench connection?????????????????????????????? ????...12 powering the board????????????????????????????????? ???..13 running the software gui??????????????????????????? ??????..14 software gui fault handling instructions??????????? ????????????????.17 IRMD2336DJ software gui reference guide???????????? ??????????????.18 motor parameters??????????????????????????????????? ??.18 inverter parameters???????????????????????????????? ????..18 system status?????????????????????????????????????? ?18 control??????????????????????????????????????????18 monitors?????????????????????????????????????????.. 19 speed control?????????????????????????????????????? ?19 IRMD2336DJ circuit schematics?????????????????????? ??????????20 IRMD2336DJ bill of material???????????????????????? ??????????24 IRMD2336DJ specifications?????????????????????????? ????????27 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 3 list of figures figure1: IRMD2336DJ system block diagram??????????? ???????????????..?6 figure 2: picture of IRMD2336DJ reference design??? ????????????..?????????..7 figure 3: irs2336dj application diagram???????????. ?????????????????...7 figure 4: bootstrap circuit???????????????????????? ???????????...8 figure 5: gate circuit????????????????????????????? ?????????8 figure 6: protection circuits, fault reporting & au tomatic reset after itrip fault????????????..10 figure 7: 20 pin connector, p1????????????????????? ????????????.10 figure 8: test bench connection???????????????????? ????????????..12 figure 9: board connections???????????????????????? ??????????.13 figure 10: 8 pin connector, j1????????????????????? ????????????..13 figure 11: location of diagnostic leds in irmd2336d j?????????????????????....14 figure 12: software gui before establishing communi cation between IRMD2336DJ and pc?????.?14 figure 13: com port selection?????????????????????? ???????????..15 figure 14: software gui after establishing communic ation between IRMD2336DJ and pc???????.15 figure 15: software gui after successful configurat ion of IRMD2336DJ???????????????.16 figure 16: software gui while running the motor usi ng IRMD2336DJ????????????????..17 figure 17: software gui during 2 different fault si tuations?????????????????????..17 figure 18: IRMD2336DJ power stage circuit schematic ??????????????????????..20 figure 19: IRMD2336DJ digital control & communicati ons circuit schematic????????????...21 figure 20: IRMD2336DJ rs-232 drivers & receivers ci rcuit schematic??????????????....22 figure 21: IRMD2336DJ dc-dc converter low voltage p ower supply circuit schematic???????..23 list of tables table 1. gate drive circuit components????????????? ?????????????????8 table 2. list of test points??????????????????????? ????????????.11 table 3. list of faults issued by gui?????????????? ?????????????????19 table 4: IRMD2336DJ electrical specifications?????? ????????????????????.27 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 4 safety precautions in addition to the precautions listed throughout th is manual, please read and understand the following statements regarding hazards associated with develo pment system. attention: the ground potential of the IRMD2336DJ system is bi ased to a negative dc bus voltage potential. when measuring v oltage waveform by oscilloscope, the oscilloscope ground needs to be i solated. failure to do so may result in personal injury or death. attention: the IRMD2336DJ system contains dc bus capacitors, w hich take time to discharge after removal of main supply. before work ing on drive system, wait three minutes for capacitors to discharge to safe voltage levels. failure to do so may result in personal injury or death. darkened display leds is not an indication that cap acitors have discharged to safe voltage levels. attention: only personnel familiar with the drive and associat ed machinery should plan or implement the installation, start-up, and s ubsequent maintenance of the system. failure to comply may result in personal in jury and/or equipment damage. attention: the surface temperatures of the drive may become ho t, which may cause injury. ! ! ! ! downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 5 attention: the IRMD2336DJ system contains esd (electrostatic d ischarge) sensitive parts and assemblies. static control prec autions are required when installing, testing, servicing or repairing this assembly. comp onent damage may result if esd control procedures are not followed. if you are not familiar with static control procedures, reference applicable esd protection han dbook and guideline. attention: an incorrectly applied or installed drive can resul t in component damage or reduction in product life. wiring or application errors such as undersizing the motor, supplying an incorrect or inadequate ac supply, or excessive ambient temperatures may result in system malfunction. attention: remove and lock out power from the drive before you disconnect or reconnect wires or perform service. wait three minu tes after removing power to discharge the bus voltage. do not attempt to servic e the drive until bus voltage has discharged to zero. failure to do so may result in bodily injury or death. attention: do not connect power factor correction capacitors t o drive output terminals u, v, and w. failure to do so may result in equipment damage or bodily injury. debris when unpacking IRMD2336DJ system is shipped with packing materials that need to be removed prior to installation. attention: failure to remove all debris and packing materials which are unnecessary for system installation may result in overheating o r abnormal operating condition. ! ! ! ! ! downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 6 IRMD2336DJ ? hardware description the IRMD2336DJ reference design kit supports the ev aluation of the irs2336dj which is a high voltage p ower mosfet and igbt driver. the reference design is a f ull-function unit operating out of 220vac input. an onboard digital controller ic enables driving an induction motor in open-loop volts-per-hertz mode. the includ ed gui software allows modification of system parameters i n order to drive an induction motor in open-loop vo lts-per- hertz mode and study the irs2336dj high voltage gat e driver ic by changing parameters such as pwm frequency and deadtime. the reference design is equ ipped with protection against motor line-to-line an d line-to- dc bus(-) short by way of the motor overcurrent pro tection function provided by irs2336dj and also a g ui software controlled motor current limit. the board includes multiple test points to facilitate monitor ing irs2336dj input and output signal waveforms and examining its various features. top level description the IRMD2336DJ reference design is composed of the following key blocks: the input stage includes an emi filter, 8a bridge rectifier and dc bus capacitor rated for 400w conti nuous operation. it is noted that IRMD2336DJ does not fea ture a current limiting fuse. the power inverter uses 6 x irgib10k60d1 igbt powe r switches mounted on a 1.9 o c/w heatsink. the igbts can be replaced with user preferred power dev ices but user may need to replace components such as bridge rectifier & dc bus current shunt to match the device ratings. the gate driver circuitry is based on irs2336dj hi gh-voltage gate driver ic and associated circuitry involving bootstrap capacitors, gate drive timing r esistors, and associated fault diagnostic elements. the control circuitry for driving the motor is bas ed on the irmcf341 digital control ic. the irmcf341 control ic has been configured to run an induction motor in the open-loop volts-per-hertz mode. the control ic generates the pwm signals for irs2336dj gate driver. the user also has the option to drive the irs2336dj externally by disconnecting the jumpe rs on connector p1 and bridging in external connections. the digital ic communicates with a pc over an isolated serial link and the included gui software allows the user to set the motor speed and modify common inverter parameters such as switching frequency and deadtime. an on-board dc-dc converter low voltage power supp ly derives the 15v, 3.3v & 1.8v rails from the main dc bus. for more information regarding the other blocks of the reference design, please refer to the detailed schematics. figure 1 IRMD2336DJ system block diagram downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 7 figure 2: picture of IRMD2336DJ reference design irs2336dj gate driver ic the irs2336dj ic integrates three independent half bridge drivers with shoot through protection and in ternal dead-time insertion. proprietary hvic technology en ables ruggedized monolithic construction with logic inputs compatible with cmos or lsttl levels as low as 3.3 v. the output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. propagation delays are matched to simplify use in high frequency applications. the floating channel can be used to drive n-channel power mosfets or igbts in the high side configuration, which operates up to 600v. the ic is based on ?active low? input logic i.e. a logic high input turns off the corresponding output and vice v ersa. in addition to vss pin, the ic features a com pin to provide a dedicated, low impedance return path for the low side gate driver which also serves to shunt the high- frequency gate drive currents away from the current sense resistor thus preventing false trips. a host of protection functions such as uvlo for vcc & vbs supplies and m otor current trip along with integrated fault diagn ostics are also offered in irs2336dj i. an open-drain fault signal is provided to indicate that an over-current or a vcc under-voltage shutdown has occurred. fault conditio ns are cleared automatically after a delay programm ed externally via an rc network connected to the rcin input. an enable function is available to terminate all six outputs simultaneously. figure 3: irs2336dj application diagram input stage power inverter gate driver circuitry connector for external pwm drive dc-dc converter control circuitry power connector pc connector input stage power inverter gate driver circuitry connector for external pwm drive dc-dc converter control circuitry power connector pc connector downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 8 bootstrap supply circuit the floating high side driver supplies in irmd2336d j are generated by a bootstrap circuit as shown in figure 4. the ic turns on the internal ?bootfet? when the low side transistor is on to charge up the bootstrap c apacitor (c boot ). the ?bootfet? eliminates the requirement for an external bootstrap diode d boot as is the case for previous generation gate drivers. an application note an-112 3 ( http://www.irf.com/technical-info/appnotes/an-1123. pdf ) describes the selection of the bootstrap capacitor and considerations when using the internal bootfet. in some cases, an external bootstrap circuit may be prefera ble. the IRMD2336DJ board also provides option for external bootstrap supply. this can be invoked by populating the bootstrap resistor, r boot (r17) and bootstrap diodes (d6, d7 & d8). the bootstrap capacitors must be fully charged to a void missing high side pulses due to under voltage lockout on the floating high side supply. the digital controll er on the board pre-charges the capacitors by turni ng on the low side transistors for a short period before starting to run the motor. the charging current and time de pends on the resistance of the internal bootfet or the external boot resistance. typically, the pre-charge sequence charges the capacitors one at a time to avoid spurious over current trips since the charging current flows thr ough the current sensing shunt. figure 4: bootstrap circuit gate drive resistors the IRMD2336DJ board has resistor-diode network on the outputs of the driver ic to allow fine tuning o f the power switch turn on and turn off times. figure 5 shows the gate circuit schematic while table 1 lis ts the resistors & diodes used in the network for each power device. figure 5 : gate circuit u v w high side gate (ho turn-on/off) r61/r99/d9 r62/r101 /d10 r63/r118/d11 low side gate (lo turn-on/off) r64/r119/d12 r65/r12 0/d13 r66/r121/d14 table 1: gate drive resistor network

downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 9 IRMD2336DJ protection features motor overcurrent protection motor over-current protection is implemented using a dc link shunt resistor (r60) placed between power ground (com pin) and logic ground (vss pin) as shown in fi gure 6. the itrip signal from the shunt has an inpu t rc filter (r38, c37) to reject power inverter noise. t he irs2336dj has a comparator that generates a shut down signal when the itrip pin voltage exceeds the itrip threshold (v it,th+ ). an internal noise filter rejects pulses shorter than 400ns to avoid spurious trips due to d iode reverse recovery current. the shutdown signal turns off all six outputs and pulls the fault pin & rcin pin low. when the over-current condition is cleared, the fault remains latched until reset by the voltage on the rcin. under-voltage protection circuits the ic monitors the supply voltage on the v cc pin. it turns off all six outputs and pulls the fault pin low when v cc falls below a minimum threshold (v ccuv- ). this fault is not latched but is cleared once v cc goes above the positive going threshold (v ccuv+ ). the ic also features uvlo protection for all 3 v bs floating supplies; however, a vbs uvlo condition does not trigger a fault repor ting i.e. fault pin is not pulled low under vbs uvlo. under a vbs uvlo condition, the corresponding gate driver output is terminated until the vbs uvlo condition is cleared. IRMD2336DJ fault reporting the fault pin of the ic is used to communicate a fault situat ion to the digital control ic. the fault pin, which is normally pulled up to 3.3v using pull up resisto r, is connected to the gatekill pin on the irmcf341 . when the ic detects a fault situation (either due to vcc uvlo or itrip) all gate driver outputs are shut-do wn and the fault pin is pulled low and this triggers the gatekill fu nction of irmcf341 causing all pwm outputs of irmcf341 to be shutdown. fault reporting is perform ed only for the following: - motor overcurrent (itrip) - vcc supply uvlo it is again noted that vbs uvlo does not trigger a fault situation. automatic reset after itrip fault automatic fault reset provided by the hvic is based on the time constant (rc reset ) of the passive network on the rcin pin. an rc network (r39, c38) between the rcin pin and vcc supply allows an automatic reset of th e itrip fault. the capacitor on the rcin pin is held low as long as the itrip comparator input exceeds t he itrip voltage threshold. when the itrip fault condition c lears, the capacitor is allowed to charge up. the i trip fault is reset when the capacitor voltage exceeds a minimum threshold (v rcin,th+ ). the rcin auto-reset time can be calculated from the following equation: ? ? = + rcinth cc cc v v v c r t ln 38 39 the reference design auto reset time is approximate ly 1.6ms for v cc =15v, v rcinth+= 8v and r 39 =2mohm, c 38 =1nf. the on resistance of the reset fet on the rcin pin cannot be neglected so a relatively small capacitor should be used so that it becomes fully discharged before the fault is released. enable function the ic features a dedicated en pin to provide enabl e/disable functionality with the functionality enab led when en pin is biased high. in the irmd2336d reference desi gn, en pin is tied to 3.3v dc bus potential to alwa ys enable operation. downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 10 figure 6: protection circuits, fault reporting & au tomatic reset after itrip fault pwm input to irs2336dj & connection of an external system controller IRMD2336DJ is configured by default to use the pwm signals from the on-board irmcf341 controller for t he irs2336dj hvic. the default configuration connects the irmcf341 digital control ic to the irs2336dj b y shorting pins 5-6, 7-8, 9-10, 11-12, 13-14, 15-16, 17-18 on connector p1 shown in figure 7. since the irs2336dj is based on active low logic, the pwm inp uts to the hvic in IRMD2336DJ are connected to 3.3vdc using pull-up resistors (r26 to r32). an external controller can easily be invoked for dr iving the irs2336d by removing the shorting connect ions on the 20 pins dil connector p1 and connecting the external pwm signals to the odd numbered pins on p1 . it is reiterated that the correct pwm inputs that i s appropriate for the ?active low? logic of irs2336 dj must be maintained. figure 7: 20-pin connector p1 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 11 test points for investigation the reference design is provided with ample test po ints to probe the different pins of the gate driver ic and inverter circuit. the following table provides a su mmary of the most useful test-points around the irs 2336d hvic and their associated functionality. test point # test point name remark tp28, 29, 30 u, v, w motor phase nodes (also negat ive terminals of bootstrap supply voltage) tp37, 38 & 39 vb3, vb2, vb1 boot-strap supply volta ge positive terminal tp9, 10, 11 uh, vh, wh pwm input to high-side chann els of hvic (hin1, hin2 & hin3) tp31, 32, 33 ug, vg & wg gate of high-side igbts tp7, 8, 9 ul, vl, wl pwm input to low-side channels of hvic (lin1, lin2 & lin3) tp34, 35, 36 ug/, vg/, wg/ gate of low-side igbts tp24 com common emitter of low-side igbts (also pos itive terminal of current shunt resistor) tp22 gk fault pin of irs2336d (also input to irmcf341 gatekill pin) tp2 ifb motor current feedback tp4 dcp dc bus tp14, 15, 25, 26, 27 gnd logic ground of irs2336d ( vss pin) & dc bus return tp103 vcc vcc pin of irs2336d table 2: list of test points downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 12 IRMD2336DJ ? operating instructions the following hardware is supplied with the irmd233 6dj reference design kit IRMD2336DJ board with heat sink IRMD2336DJ gui software cd-rom pc usb-serial cable & driver cd-rom visually inspect IRMD2336DJ board to check for loos e wiring, loose or damaged components or other abnormalities before proceeding. step 1: software installation the reference design kit is supplied with irmd2336d j gui v1.0 software intended to support the evaluat ion of irs2336dj hvic. the on board digital control ic (irmcf341) generates the inverter pwm signals and can run a three phase induction motor using open lo op v/f or volts-per-hertz control. this software is the gui that allows the specification of the motor, inv erter and system parameters. the software tool is distributed on a cd-rom. load the cd into the cd-rom drive on a pc and if installation does not start double-click on the .ex e installation file. the automated procedure instal ls all necessary software and documentation on the pc. the default location for the installation is ?c:\progr am files\ir\IRMD2336DJ?. step 2: test bench connection 1. connect the ac power cables to earth (e), line ( l) and neutral (n) terminals of j1 connector. prep are a power contactor switch rated at 250v/10a in serie s with ac power cables if necessary. attention: turn off or unplug the power before making any conn ections to board. all circuits on the board must be considered as ?live? with respect to the safety earth so please use extreme caution when making connections to circuit board. it is recommended to isolate the oscilloscope ground when making circuit waveform measurements. 2. connect the motor windings to the u/v/w terminal s of connector j1. if needed, connect the motor frame to the safety earth connection available on t he e terminal of connector j1. note: gnd terminal of connector j1 is not to be used for the purpose of safety grounding. 3. connect the rs-232 cable between the db-9 connec tor j6 on IRMD2336DJ board and an available com port (usb port) on your pc. the rs-232 serial c onnector is galvanically isolated from the circuit board ground so the user can safely connect a pc to the board. ! figure 8: test bench connection ! downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 13 figure 9: board connections e safety earth (connected to the heatsink) l ac line input n ac neutral input gnd dc bus ground dcp positive dc bus u motor u phase v motor v phase w motor w phase figure 10: 8-pin connector j1 attention: the gnd terminal of connector j1, called dc bus gro und, is biased to the negative dc bus voltage potential of IRMD2336DJ, wh ich connects to the ac power line input via the input rectifier. the gnd terminal is not to be confused with safety ground of the system. instead, the e terminal of connector j1 , called safety earth, is to be used for purpose of safety grounding. failure to follow thes e instructions can result in personal injury or death. step 3: powering the board connect the power cables to 220vac mains and turn-o n the power switch. there are 2 on-board leds for diagnostic purposes as shown in fig.11. 1. check if led2 is lit in red after you apply ac p ower. led2 is connected to the dc bus and indicates that power is connected to the board and the on-board sw itching mode power supply is active. note: never attempt to service the board or engage/disen gage any connections when led2 is lit since it indicates the presence of high-voltages on the b oard. 2. check if led1 is a slowly flashing green. led1 i s driven by the digital control ic irmcf341 control ler. it is lit red when a fault is detected and slowly flas hes green when irmcf341 is in proper operational status. if led1 is lit red after powering the board then it indicates one of the following: i. under-voltage fault: this occurs if rectified dc bus voltage is less th an 120v; check dc bus & ac input voltage levels and ensure dc bus is greater t han 120v. then proceed to step 4. led1 will be a flashing green once step 4 is completed. ii. over-voltage fault : this occurs if rectified dc bus voltage is greate r than 360v; check dc bus & ac input voltage levels and ensure that dc bus is less than 360v. then proceed to step 4. led1 will be a flashing green once step 4 is completed. iii. reference design configuration error: contact ir support. ! downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 14 figure 11: location of diagnostic leds in irmd2336d j step 4: running the software gui step 4a: start the gui software program on pc start the gui software by clicking the desktop icon or double-clicking .exe file. figure 12: software gui before establishing communi cation between pc & IRMD2336DJ note the following: - all 3 icons in system status section of gui (conn ection status, fault status & configuration status) are yellow in color. - all buttons in the controls section of gui are di sabled led1 led2 led1 led2 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 15 - at the bottom of the gui, the messages ?no com po rt set? & ?disconnected? are displayed step 4b: selecting the com port (rs-232) the software on the pc communicates with the digita l control ic on-board using a com port. it is neces sary to select the com port on the pc to which the usb c able is connected to run the gui software. com port setting can be selected by clicking on ?com setting s? at the bottom-left of the gui window. figure 23: com port selection dialog when the correct com port is selected and after com munication is successfully established between the pc and digital control ic, - the ?connection status? & ?fault status? icons in the system status section should change colors fro m yellow to green, - the monitor section icons should change color fro m yellow to green and provide real time information - the ?fault clear? & ?configure? buttons in contro ls section are enabled - at the bottom of the gui, the messages ?com# set? (where # is the appropriate com port number) and ?com port up? are displayed. figure 14: software gui after establishing communic ation between pc & IRMD2336DJ note: if any faults occurred during step 3 and caused le d1 to be lit red, then the ?fault status? and monitor section icons in the gui will also appear r ed with the reason for the fault (?over-voltage fau lt? or ?under-voltage fault?) displayed at the bottom of t he gui. as long as the reason for the fault has bee n determined and rectified in step 3, please continue to step 4c. downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 16 step 4c: configuring the hardware after the selection of inverter and motor parameter s on the gui click on the ?configure? button to loa d them to the digital control ic on the IRMD2336DJ board. thi s step is absolutely necessary before the motor can be started. please refer to ?software gui reference guide? sect ion for more information about gui parameters and the associated system implications. upon successful configuration, the - the ?configuration status? icon in the system sta tus section should change colors from yellow to gre en - the ?start? button in controls section is enabled note: remember to press the configure button every time after a change is made to any gui parameter. note : the dc bus voltage must remain constant after press ing the configure button, otherwise the control algorithm will not operate as expected. remember to press the configure button after every time the dc bus level is altered. figure 15: software gui after successful configurat ion of IRMD2336DJ downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 17 step 4d: starting, running & stopping the motor to start the motor, press the ?start? button in the controls section. the motor will start and acceler ate to the specified rotation speed. further, the ?start? butt on in the controls section of the gui will toggle i nto a ?stop? button. figure16: software gui while running the motor usin g IRMD2336DJ while running, the motor speed can be changed real- time by using the slider to set the new speed. to s top the motor, simply press the ?stop? button. the moto r will coast to a full stop. further, the ?stop? bu tton will toggle back to ?start?. software gui fault handling instructions a fault situation may be triggered either by the so ftware gui or hardware (digital control ic). please refer to the ?software gui reference guide? section for more information about the fault conditions that can be encountered during operation. in both cases, when a fault is encountered during motor operation, the gui immediately stops the motor. further, - the ?fault status? icon in system status section changes to red - if any of the monitors are related to the fault c ondition, then the appropriate monitor icon also ch anges color to red - the ?start? button in controls section is disable d - the fault condition is displayed at the bottom of the gui figure17: software gui during 2 different fault sit uations to clear the fault and restart motor, the following actions are performed in the specified sequence - press the ?fault clear? button in controls sectio n; the ?fault status? icon & the respective system monitor icon in system status section then change from red to green - reconfigure the motor as outlined in step 4b - proceed to running the motor as outlined in step 4c downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 18 IRMD2336DJ ? software gui reference guide motor parameters number of poles ? the number of poles defines the ratio of the ele ctrical to mechanical frequency in the induction motor (# of poles = electrical freque ncy/mechanical frequency). this is selected from the drop down menu in the gui. only even number val ues are listed in the drop down menu since the motor poles come in pairs. max speed ? this is the maximum speed that the motor can run . the motor speed cannot be set faster than this value. this is entered in revoluti ons per minute (rpm). this parameter can be obtained from the motor nameplate. min speed ? this is the minimum speed that the motor can run . the speed cannot be set lower than this value. this is entered in revolutions per minu te (rpm). current limit ? this is the maximum rms current (phase current i n the motor) that the system will allow in the motor before the gui triggers a fault and stops the motor. this is entered in amperes (a) . this parameter can be obtained from the motor namep late. volts ? this is the rated rms voltage (l-l) of the induct ion motor. this parameter is the voltage used in the v/hz control algorithm. this is entered in volts (v). this parameter can be obtained from the motor nameplate . note : when the configure button is pressed this value is sampled along with the current dc bus. the dc bus must remain constant after pressing the configure button, otherwise the control algorithm will not operate as expected. base speed ? this is the rated electrical frequency for runni ng the induction motor. this parameter is the hertz value used in the v/hz control algorit hm. this is entered in hz. this parameter can be obtained from the motor nameplate . inverter parameters carrier frequency - user selectable input of pwm frequency of invert er. this is entered in khz in the range from 5khz to 35khz. dead time ? the dead time that will be present between switc hing high and low side igbts. this is entered in s. typically deadtimes are less than 1usec. system status connection status ? indicates if the connection between software and irmcf341 is working and active. green indicates successful connection, whil e yellow indicates lack of connection. other system status icons also remain yellow when there i s no connection. fault status ? indicates if any faults are present in the syste m. green indicates fault-free status while red indicates occurrence of a fault. the faul t condition is displayed at the bottom of the gui a nd the associated monitor icon is also lit red, if app licable. faults can be cleared by pressing the faul t clear button. if the fault remains even after press ing the fault clear button then it indicates that t he fault situation is continuing to persist. table 3 s hows a list of all the faults that can be encounter ed. configure status ? indicates if any parameters have been modified s ince the last configure. if this indicator is yellow, the configuration button shoul d be pressed again prior running the motor. it is recommended to press the configuration button every time before starting and running the motor. control fault clear ? this button will clear all of the faults present in the system. if the fault remains after pressing this button it indicates that the fault si tuation is continuing to persist. this button will be disabled when a pc-to-hardware connection is not pr esent and when the motor is running. shut- down power and restart gui to resume operation. configure - this button will configure the hardware with the parameters that have been selected in the gui. this step is not done automatically. remem ber to configure the hardware every time a downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 19 parameter is altered or dc bus voltage level is cha nged. this button will be disabled when a pc-to- hardware connection is not present and when the mot or is running. shut-down power and restart gui to resume operation. start/stop ? this toggle-type button starts and stops the moto r. during motor-start, an acceleration control gradually ramps the motor speed to the valu e in ?requested speed? field. fault condition fault type (source) explanation of fault fault trip level over- voltage fault hardware generated (by digital ic) indicates dc bus over-voltage condition at system power-up (note: this fault occurs only during power up, when gui is still unconfigured ) dc bus voltage > 360v under- voltage fault hardware generated (by digital ic) indicates dc bus voltage under-voltage condition at system power-up (note: this fault occurs only during power up, when gui is still unconfigured ) dc bus voltage < 120v dc bus voltage level fault hardware generated (by digital ic) indicates either a dc bus over-voltage or under-voltage condition (note: this fault occurs after gui has been configured ) dc bus voltage > 360v or dc bus voltage < 120v gatekill fault hardware generated (by hvic) indicates itrip fault or vcc uvlo fault occurring in irs2336d; gatekill fault is triggered by fault pin of irs2336d vcc < 8.2v (typ) and/or v(r60) > 14a (typ) overcurrent fault software generated indicates that motor current fault rms motor current calculated by gui > ?current limit? system error software generated indicates out-of-bounds errors, contact ir support - table 3: list of errors obtainable during testing & associated conditions monitors dc bus voltage ? the instantaneous voltage of the dc bus. the over- voltage fault is encountered if the dc bus increases beyond 360v. the under-voltage fault is encountered if dc bus is less than 120v. output current ? the rms motor current calculated by software. it i s dependent on the shunt resistor value defined on the system parameter. the over-cur rent fault is encountered if the calculated value exceeds the ?current limit? parameter. speed control the start button in the gui starts the motor and g radually ramps the motor speed to the specified value in ?requested speed? field. in addition, the gui has a slider to adjust the motor if it is alrea dy running. an acceleration control is included to gen tly accelerate to the requested speed and is not user definable. a modulation index is shown just above the speed s lider. this index will not go beyond 100%, nor can a speed that will cause a modulation index grea ter than 100% be selected. this causes the slider lock before reaching its maximum speed. if a greate r speed is required, increase the dc bus voltage and press configure. this will decrease the associa ted modulation index for a given speed. downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 20 IRMD2336DJ ? circuit schematics figure 18: IRMD2336DJ power stage circuit schematic 1 2 3 4 5 6 a b c d 6 5 4 3 2 1 d c b a c25 2.2uf, 25v d6 dni c26 2.2uf, 25v d7 dni c27 2.2uf, 25v d8 dni r17 dni 3 2 1 q4 irgib10b60kd1 3 2 1 q3 irgib10b60kd1 3 2 1 q1 irgib10b60kd1 3 2 1 q2 irgib10b60kd1 3 2 1 q5 irgib10b60kd1 3 2 1 q6 irgib10b60kd1 r60 0.030, 3w c20 0.1uf vcc c24 10uf,25v pwmuh pwmvh pwmwh pwmul pwmvl pwmwl ifb gnd gatekill r28 4.7k r26 4.7k r27 4.7k r29 4.7k r30 4.7k r31 4.7k r32 4.7k t rt1 ptc/n5rl20 + cap1 470uf, 450v - 1 2 3 + 4 br1 gbu806 1 2 3 4 5 6 7 8 j1 jk55b-100-8 u v w gnd neutral dcp line earth 1 tp4 dcp 1 tp14 gnd 1 tp15 gnd ifb 1 tp2 ifb cx1 0.1uf 250vac 1 4 3 2 t1 uu_10.5- 1mh, 4.8a cx2 0.1uf 250vac cy1 2.2nf cy2 2.2nf dcp c34 0.1uf,630v power stage r38 20k c37 100pf r39 1m c38 0.01uf w v u ho1 ho2 ho3 lo1 lo2 lo3 r64 33 r65 33 r66 33 r61 33 r62 33 r63 33 vb1 vb2 vb3 ug vg wg /ug /vg /wg itrip rcin 1 tp22 gk +3.3v c44 0.1uf c45 10uf 1 tp24 com 1 tp25 gnd 1 tp26 gnd 1 tp27 gnd 1 tp28 u 1 tp29 v 1 tp30 w 1 tp32 vg 1 tp31 ug 1 tp33 wg 1 tp34 /ug 1 tp35 /vg 1 tp36 /wg 1 tp37 vb3 1 tp38 vb2 1 tp39 vb1 vcc d14 mbr0530t1 r121 33 d13 mbr0530t1 r120 33 d12 mbr0530t1 r119 33 d11 mbr0530t1 r118 33 d10 mbr0530t1 r101 33 d9 mbr0530t1 r99 33 vcc 3 hin1 4 hin2 5 hin3 6 lin1 8 lin2 9 lin3 10 fault 12 itrip 14 en 16 rcin 17 vss 19 com 22 lo3 23 lo2 24 lo1 25 vs3 29 ho3 30 vb3 31 vs2 35 ho2 36 vb2 37 vs1 41 ho1 42 vb1 43 u5 irs2336d vcc +3.3v +3.3v r35 4.7k downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 21 figure 19: IRMD2336DJ digital control & communicati ons circuit schematic 1 2 3 4 5 6 a b c d 6 5 4 3 2 1 d c b a c35 47pf, 50v current shunt feedback ifb gnd + c5 10uf,10v c62 0.1uf c61 0.1uf c63 0.1uf c66 0.1uf c68 0.1uf c67 0.1uf c98 0.01uf c97 0.01uf c99 0.01uf c10 0.01uf c96 0.01uf c95 0.01uf 1.8v +3.3v 1.8v +3.3v xtal0 1 xtal2 2 p1.0/t2 3 p1.1/rxd 4 p1.2/txd 5 p1.3/sync/sck 6 p1.4/cap 7 p1.5 8 p1.6 9 p1.7 10 vdd2 11 vss 12 p2.0/nmi 14 p2.1 15 p2.2 16 p2.3 17 p2.4 18 p2.5 19 p2.6/aopwm0 20 p2.7/aopwm1 21 vdd2 22 vss 23 avdd 25 avss 26 ain0 24 ain1 27 cmext 28 aref 29 ifb- 30 ifb+ 31 ifbo 32 ain2 33 ain3 34 ain4 35 ain5 36 ain6 37 vdd2 38 vss 39 vdd1 40 gatekill 41 pwmwl 42 pwmwh 43 pwmvl 44 pwmvh 45 pwmul 46 pwmuh 47 p3.0/int2/cs1 48 p3.1/aopwm2 49 p3.2/nint0 50 p3.3/nint1 51 vss 53 vdd1 54 scl/sdi-sdo 55 sda/cs0 56 p5.1/tms 57 p5.2/tdo 58 p5.3/tdi 59 tck 60 tstmod 61 reset 62 pllvdd 63 pllvss 64 vdd1 13 p3.5/t1 52 u2 irmcf341 pwmuh pwmul pwmvh pwmvl pwmwh pwmwl gatekill 1 3 2 4 s1 kt11p3jm c65 10uf, 10v c69 0.1uf cl1 15pf cl2 15pf 1 2 3 4 cr1 cm309s4.000mabjtr b c e q7 mmbt3904lt1 +3.3v rx1 tx1 c12 0.1uf c3 0.1uf c9 0.01uf c6 0.1uf c8 0.01uf dac0 dac1 dac2 c14 0.1uf cmext ifb+ ifb- ifbo gatekill pwmwl pwmwh pwmvl pwmvh pwmul pwmuh ain1 ain2 ain3 ain4 ain5 ain6 p3.0 dac2 p3.2 p3.3 p2.0 p2.1 p2.2 vcc_short p2.4 p2.5 dac0 dac1 p1.0 rx1 tx1 p1.3 p1.4 p1.5 p1.6 p1.7 tdo tms tdi tck tstmod rst aref 1.8v u2-1 u2-2 c84 10uf, 10v c83 0.1uf +3.3v +3.3v c32 0.1uf a0 1 a1 2 nc 3 gnd 4 sda 5 scl 6 wp 7 vcc 8 u17 at24c512bn a0 1 a1 2 nc 3 gnd 4 sda 5 scl 6 wp 7 vcc 8 u20 at24c02bn +3.3v c46 0.1uf +3.3v scl sda r14 0 r16 0 r18 0 r19 0 c21 10uf,10v c22 10uf,10v r12 1k +3.3v r11 1k dc bus feedback dcp c43 2200pf ain0 1 tp12 rst 1 tp42 aref c4 33pf, 50v 1 2 3 4 led1 lnj115w8ara +3.3v green red 1 2 jp1 +3.3v 1 2 jp2 +3.3v + c31 10uf,10v c33 47pf dcp +3.3v 1 2 3 4 5 6 j5 prpn061paen 4 2 5 3 u3 sn74lvc1g14dck 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 j3 prpn082paen from shunt resistor from shunt resistor r54 0 r52 100 r53 100 r88 4.7k r87 4.7k r89 4.7k r42 10k r25 4.7k r15 1k r43 10k r58 10k r24 10k r57 0 r22 0 r55 0 r40 0 dbrst_i nrst_i r2 0 r3 dni r34 1.00m r20 1.00m r21 4.87k r80 1.00k r83 1.00k r81 5.11k r82 5.11k r77 11.8k r79 11.8k rd 10 rf 1m r6 0 vdd1 1 gnd1 2 via 3 vib 4 vob 13 voa 14 gnd2 15 vdd2 16 vic 5 vod 6 ve1 7 gnd1 8 voc 12 vid 11 ve2 10 gnd2 9 iso3 adum1401brw vdd1 1 voa 2 vib 3 gnd1 4 gnd2 5 vob 6 via 7 vdd2 8 iso4 adum1201br tdo_i tms_i tdi_i tck_i c42 0.1uf c41 0.1uf c39 0.1uf c40 0.1uf +3.3v +3.3v 5v_i 5v_i 5v_i nrst dbrst +3.3v r1 4.7k r7 4.7k r8 4.7k r10 4.7k r13 4.7k 1 2 3 4 5 j7 prpn051paen 1 tp5 scl p3.5 1 tp6 ul 1 tp9 wh 1 tp10 vh 1 tp11 uh 1 tp7 vl 1 tp8 wl r33 2.00k 1% c23 10nf ,50v r59 1.00k 1% 1.8v r68 0 r67 0 1 tp23 ifbo r76 470 r84 470 r85 470 r86 470 r90 470 r91 470 tck 1 gnd 2 tdo 3 4 tms 5 vcc 6 trig 7 dbreset 8 tdi 9 gnd 10 j11 3m 2510-6002ub r75 1k 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 p1 ? +3.3v +3.3v downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 22 figure 20: IRMD2336DJ rs-232 drivers & receivers ci rcuit schematic 1 2 3 4 a b c d 4 3 2 1 d c b a r49 1k c92 0.01uf r48 1k c91 0.01uf r50 1k c94 0.01uf c90 0.01uf r51 1k r47 1k c93 0.01uf c89 0.01uf r46 1k dac0 dac1 dac2 1 tp16 5v_i 1 fid3 1 fid5 1 fid2 1 fid4 1 fid1 1 fid6 1 2 3 4 5 6 7 8 9 mh1 mh2 j6 db9rf rs-232 drivers / receivers d/a filter dac0 dac1 dac2 1 tp1 vss v+ 3 v- 7 en 1 invalid 10 c1- 4 c1+ 2 gnd 14 vcc 15 forceon 12 forceoff 16 dout 13 rin 8 c2+ 5 c2- 6 din 11 rout 9 u4 max3221cdbr rx1 tx1 rx_i tx_i c52 0.1uf c53 0.047uf c54 0.33uf c50 0.33uf c51 0.33uf r41 0 r44 0 r56 0 r78 dni vdd1 1 voa 2 vib 3 gnd1 4 gnd2 5 vob 6 via 7 vdd2 8 iso5 adum1201br 5v_i 5v_i +3.3v c29 0.1uf c30 0.1uf 5v_i 1 tp18 da0 1 tp19 da1 1 tp20 da2 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 23 figure 21: IRMD2336DJ dc-dc converter low voltage p ower supply circuit schematic 1 2 3 4 5 6 a b c d 6 5 4 3 2 1 d c b a 1 tp103 vcc l100 10uh, 3a r117 75k,1w r113 1k r109 100 1 tp100 gnd c110 10nf,50v c113 470uf,16v r107 2.00k c118 270pf,1kv d3 us1jdict 1 tp101 gnd c100 100uf,25v r104 1.6k c115 47uf,35v r100 330 r111 1k 1 tp106 dcp r105 5.1k c101 220uf,35v d5 10mq100n c102 330pf,50v r102 1m r110 22k vcc 7 out 6 is 3 gnd 5 rt/ct 4 vref 8 comp 1 vfb 2 u103 uc3842d8 3 1 d4 6tq045 r108 47 r106 68k c111 470pf,50v r115 200k,1w c117 0.1uf,50v 1 tp107 3.3v c108 330pf,50v r116 75k,1w 6 7 3 4 5 8 1 2 9 10 t100 ee16 c112 1000uf,16v r114 200k,1w r112 1.0,1w in 1 gnd 2 out 3 u100 njm78m15fa d2 10mq100n c109 10nf,50v 1 2 3 q100 irfbg30 1 e100 vss c116 0.1uf,630v c114 470uf,16v vcc dcp p lac e a p la ted t hr ou gh ho le f or f lyi ng l ead co nn ec tio n 100ma flyback power supply r103 10 c105 330uf, 25v c104 330uf, 25v d1 10mq100n 1 fid103 1 fid100 1 fid101 1 fid102 c107 100pf +3.3v r9 330 c19 330pf,50v flag 1 vout 3 gnd 5 gnd 6 gnd 7 gnd 8 vin 2 adj 4 u1 iru1208cs c1 68uf,16v c2 68uf,16v 1a peak 200ma ave 1.8v 1 tp3 1.8v r45 110 1.24 x ( 1 + 110/243) = 1.8 r23 243 vin 1 gnd 2 vout 3 u31 lm340t-5 1 tp17 gnd 5v_i dcp r4 75k,1w r5 75k,1w led2 ltl-16ke c16 10uf,10v 1 tp13 vss downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 24 IRMD2336DJ ? bill of materials # ## # component description component description component description component description manufacturer & part # qty qtyqty qty designator designator designator designator 1 pcb ir IRMD2336DJr0.2 1 2 conn, hdr,2x5 3m .100" x .100" 4-wall header,stand ard,straight through-hole,10 contacts,2510-6002ub 3m 2510-6002ub 1 j11 3 cap smt, 0.01uf 0603 cer 50v 10% npo/cog 14 c8-c10,c89-c99 4 cap smt, 0.1uf 0603 cer 50v 10% x7r 20 c3,c6,c12,c14,c29,c30,c32,c39- c42,c44,c46,c61-c63,c66-c69 5 cap smt, 15pf 0603 cer 50v 5% npo/cog 2 cl1,cl2 6 cap smt, 33pf 0603 cer 50v 5% npo/cog 1 c4 7 cap smt, 47pf 0603 cer 50v 5% npo/cog 2 c33,c35 8 cap smt, 10000pf 0805 cer 50v 10% x7r 4 c23,c38,c109,c110 9 cap smt, 47nf 0805 cer 50v 10% x7r 1 c53 10 cap smt, 0.1uf 0805 cer 50v 10% x7r 4 c20,c52,c83,c117 11 cap smt, 0.33uf 0805 cer 50v 10% x7r 3 c50,c51,c54 12 cap smt, 100pf 0805 cer 50v 5% npo/cog 2 c37,c107 13 cap smt, 2.2uf 0805 cer 25v +80/-20% y5v 3 c25-c27 14 cap smt, 2200pf 0805 cer 50v 5% npo/cog 1 c43 15 cap smt, 330pf 0805 cer 50v 10% x7r 3 c19,c102,c108 16 cap smt, 470pf 0805 cer 50v 10% x7r 1 c111 17 cap smt, 10uf 3216 (a) tant 16v 10% kemet t491a1 06k016at t491a106k016ag 8 c5,c16,c21,c22,c31,c45,c65,c84 18 cap smt, 10uf 6032 tant 25v 10% 1 c24 19 cap smt, 68uf 7343 tant 16v 20% 2 c1,c2 20 cap thr, 1000uf, al elec 16v 20% 1 c112 21 cap thr, 47uf, al elec, 35v 2mmls digikey p5164 1 c115 22 cap thr, 100uf, al elec, 25v 2mmls 1 c100 23 cap thr, 220uf al elec, 35v pol, (0.140"ls/3.5mm) panasonic eeu-fc1v221l digi-key p10296-nd 1 c101 24 cap tha, 330uf, al elec 25v 2 c104,c105 25 cap thr, 470uf, al elec 16v 20% 2 c113,c114 26 cap thr, 470uf,elec 450v 20% panasonic eet-uq2w471da digikey p11951-nd 1 cap1 27 cap thr, 0.1uf 300vac 20% x1 panasonic ecq-u3a104mg 2 cx1,cx2 28 cap thr, 2200pf 250vac 20% y2/x1 panasonic eck-n vs222me 2 cy1,cy2 29 osc smt, 4.0mhz crystal 18pf cm309s citizen cm309 s4.000mabjtr 1 cr1 30 conn, d-sub, 9p recpt rt angle w/ jack screws kyco n k22-e9s-nj 1 j6 31 single schmitt-trigger inverter ti sn74lvc1g14dck 1 u3 32 res smt, 0.033-ohm 1.5w 1% 2520 caddock cd2520fc -0.033 1 r60 33 smps transformer precision 019-3214-03 1 t100 34 rect bridge gpp 600v 8a gbu diode gbu806 1 br1 35 conn, hdr, 1x2 breakaway, 0.025 sq gd (0.100"/0.2 30") samtec tsw-102-07-s-s tsw-102-07-g-s 2 jp1,jp2 36 conn, hdr,1x5 sullins prpn051paen 1 j7 37 conn, hdr, 2x10 pin 0.025" sq post gold (0.100"/0 .230") samtec tsw-110-07-s-d 1 p1 38 conn, shunt, 2-pin shorting shunt 10 @ p1 39 conn, hdr,2x3 sullins prpn032paen 1 j5 40 conn, hdr,2x8 sullins prpn082paen 1 j3 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 25 # ## # component description component description component description component description manufacturer & part # qty qtyqty qty designator designator designator designator 41 common mode emi inductor burnon lcl-uf1125 1 t1 42 conn, 8p 10mm burnon jk55b-100-8 1 j1 43 switch smt, switch spst mom key j-lead smd itt k t11p3jm digikey ckn9003ct-nd 1 s1 44 led, t1 red diff lite-on ltl-16ke digikey 160-1078-nd 1 led2 45 led smt, 1.6x1.25mm bi-color green/orange digikey p11142ct-nd 1 led1 46 inductor hi current radial 10uh jw miller 6000-10 0k-rc digikey m8616-nd 1 l100 47 rs-232 transceiver ic 16l ssop maxim max3221cae 1 u4 48 digital control ic ir irmcf341 1 u2 49 res smt, 470-ohm 1/16w 5% 0603 6 r76,r84,r85,r86,r90,r91 50 res smt, 0-ohm 1/8w 5% 0805 16 r2,r6,r14,r16,r18,r19,r22,r40,r 41,r44,r54-r57,r67,r68 51 res smt, 1.0k-ohm 1/8w 1% 0805 15 r11,r12,r15,r46- r51,r59,r75,r80,r83,r111,r113 52 res smt, 1.0m-ohm 1/8w 1% 0805 4 r20,r34,r39,rf 53 res smt, 1.6k-ohm 1/8w1% 0805 1 r104 54 res smt, 10-ohm 1/8w 1% 0805 1 rd 55 res smt, 100-ohm 1/8w 1% 0805 3 r52,r53,r109 56 res smt, 10k-ohm 1/8w 1% 0805 4 r24,r42,r43,r58 57 res smt, 11.8k-ohm 1/8w 1% 0805 2 r77,r79 58 res smt, 110-ohm 1/8w 5% 0805 1 r45 59 res smt, 2.0k-ohm 1/8w 1% 0805 2 r33,r107 60 res smt, 20k-ohm 1/8w 1% 0805 1 r38 61 res smt, 22k-ohm 1/8w 5% 0805 1 r110 62 res smt, 243-ohm 1/8w 1% 0805 1 r23 63 res smt, 33-ohm 1/8w 1% 0805 12 r61-r66,r99,r101,r118-r121 64 res smt, 330-ohm 1/8w 1% 0805 1 r100 65 res smt, 4.7k-ohm 1/8w 1% 0805 17 r1,r7,r8,r10,r13,r25- r32,r35,r87-r89 66 res smt, 4.87k-ohm 1/8w 1% 0805 1 r21 67 res smt, 47-ohm 1/8w 5% 0805 1 r108 68 res smt, 5.11k-ohm 1/8w 1% 0805 2 r81,r82 69 res smt, 5.1k-ohm 1/8w 1% 0805 1 r105 70 res smt, 68k-ohm 1/8w 1% 0805 1 r106 71 res smt, 330-ohm 1/4w 5% 1206 1 r9 72 res smt, 1m-ohm 1/4w 1% 1206 1 r102 73 res smt, 10-ohm 1/4w 5% 1210 1 r103 74 res smt, 1-ohm 1w 5% 2512 1 r112 75 res smt, 200k-ohm 1w 5% 2512 2 r114,r115 76 res smt, 75k-ohm 1w 5% 2512 4 r4,r5,r116,r117 77 cap thr, 0.1uf cer,630v panasonic ecq-e6104kf digikey ef6104-nd 2 c34,c116 78 cap thr, cap 270pf 1kv ceramic disc gp 10% 1 c118 79 diode schottky 100v 1.5a d-64 ir 10mq100n 3 d1,d2, d5 80 diode ultra fast sw 600v 1a sma diodes inc us1j-1 3-f 1 d3 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 26 # ## # component description component description component description component description manufacturer & part # qty qtyqty qty designator designator designator designator 81 ic digital isolator 4ch 16-soic analog device adum1401brw 1 iso3 82 ic digital isolator 4ch 16-soic analog device adum1201br 2 iso4,iso5 83 ic seeprom 2k 2.7v so-8 atmel at24c02n-10si-2.7 1 u20 84 ic seeprom 512k 2.7v 8soic atmel at24c512n-10si-2.7 1 u17 85 ldo regulator ic ir iru1208cs 1 u1 86 ic smt, cur-mode pwm cont 8-soic ti uc3842d8 digikey 296-11281-5-nd 1 u103 87 diode smt, schottky 30v 0.5a sod-123 on semi mbr0 530t1g 6 d9-d14 88 trans smt, npn 40v 350mw sot-23 diodes inc mmbt39 04-7-f 1 q7 89 ic 15v positive regulator to220f njr njm78m15fa digikey njm78m15fa-nd 1 u100 90 igbt w/diode 600v 16a to220fp ir irgib10b60kd1 6 q1- q6 91 mosfet switching transistor 1000v ir irfbg30 1 q100 92 current limiter inrush ge sensing cl-60 digikey kc006l-nd 1 rt1 93 socket smt, 44l plcc tin smd tyco/amp 3-822516-1 digikey a97624ct-nd na u5 94 ic, reg, +5v, 1.0a, to-220---to-220 national semi lm340t-5.0 nopb st microelectroni l7805cv digi-key 497-1443-5-nd 1 u31 95 diode schottky 45v 6a d2pak ir 6tq045 1 d4 96 misc, test point mulit purpose mini wht keystone 5002 digikey 5002k-nd 44 97 components not populated 6 d6,d7,d8,r3,r17,r78 98 high voltage gate driver ic ir irs2336djpbf 1 u5 99 heatsink zhenjiang haoyang heat sink company: ds-480 1 100 insulating films for to-220 heat sink 6 @q1-q6 101 hw, washer, m3, steel, split lock---lm7805 allthr ead 1929--3-a-01aaa 6 @q1-q6 102 m3 * 8-3 m single screw, single-ended 3 m nuts, nylon, 6-column- shaped isolation 3 103 m3 * 8-3 m single screw, single-ended 3 m nuts, copper / stainless steel, six-column-shaped isolation 1 104 hw, screw, #4-40 x 5/16" machine pan head phil z inc plated allthread 1940--3--8-2a21a-0.5 pitch 11 downloaded from: http:///
IRMD2336DJ www.irf.com ? 2008 international rectifier 27 IRMD2336DJ - specifications t c = 25 c unless specified parameters values conditions input power voltage 115v-230vrms, -20%, +10% frequency 50/60 hz input current 4a rms @nominal output t a =40 c, rthsa=1.9 c/w input line impedance 4% 8% recommended output power watts 400w continuous power vin=230v ac, f pwm =10khz, f o =60hz, t a =40 c, rthsa=1.0 c/w, vertically mounted to help air flow current 3 arms nominal, 9 arms overload rthsa limits ? tc to 10 c during overload host interface (rs232c) txd, rxd 10v typical 57.6 kbps, single ended dc bus voltage maximum dc bus voltage 400v should not exceed 40 0v more than 30 sec minimum dc bus voltage 120v current feedback current sensing device 33 m ? dc link shunt single shunt reconstruction resolution 12-bit pcb design may reduce the resol ution latency 1 pwm cycle protection output current trip level 14 a peak, typical det ection from shunt on negative dc bus short circuit delay time maximum 7 " sec line-to-line short, line-to-dc bus (-) short critical over voltage trip 380 v zero vector inse rtion by digital controller over voltage trip 360 v under voltage trip 120 v power devices irgb10k60d1 x 6 rated for 10a @100 o c case with 10 s short circuit withstand capability integrated over-current protection system environment ambient temperature 0 to 40 c 95% rh max. (non-condensing) table 4 IRMD2336DJ electrical specification the information provided in this document is believ ed to be accurate and reliable. however, internatio nal rectifier assumes no responsibility for the consequences of the use of this information . international rectifier assumes no responsibilit y for any infringement of patents or of other rights of third parties which may result from the use of this information. no license is grante d by implication or otherwise under any patent or patent rights of international rectifier. the specifications mentioned in this document are subject to change without notice. this document supersedes and replaces all information pr eviously supplied. for technical support, please contact ir?s technica l assistance center http://www.irf.com/technical-info/ world headquarters: 233 kansas st., el segundo, california 90245 tel: (310) 252-7105 downloaded from: http:///

▲Up To Search▲

Price & Availability of IRMD2336DJ

	To Download IRMD2336DJ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .