? semiconductor components industries, llc, 2016 march, 2016 ? rev. 3 1 publication order number: dtc143tp/d mun5316dw1, nsbc143tpdxv6 complementary bias resistor transistors r1 = 4.7 k , r2 = k npn and pnp transistors with monolithic bias resistor network this series of digital transistors is designed to replace a single device and its external resistor bias network. the bias resistor transistor (brt) contains a single transistor with a monolithic bias network consisting of two resistors; a series base resistor and a base?emitter resistor. the brt eliminates these individual components by integrating them into a single device. the use of a brt can reduce both system cost and board space. features ? s and nsv prefix for automotive and other applications requiring unique site and control change requirements; aec-q101 qualified and ppap capable* ? simplifies circuit design ? reduces board space ? reduces component count ? these devices are pb?free, halogen free/bfr free and are rohs compliant maximum ratings (t a = 25 c both polarities q1 (pnp) and q2 (npn), unless otherwise noted) rating symbol max unit collector?base voltage v cbo 50 vdc collector?emitter voltage v ceo 50 vdc collector current ? continuous i c 100 madc input forward voltage v in(fwd) 30 vdc input reverse voltage ?npn ?pnp v in(rev) 6 5 vdc stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. ordering information device package shipping ? mun5316dw1t1g NSVMUN5316DW1T1G* sot?363 3,000 / tape & reel nsbc143tpdxv6t1g, nsvbc143tpdxv6t1g* sot?563 4,000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. www. onsemi.com marking diagrams 16 = specific device code m = date code* = pb?free package (note: microdot may be in either location) *date code orientation may vary depending up- on manufacturing location. sot?363 case 419b sot?563 case 463a pin connections (3) (2) (1) q 1 q 2 r 1 r 2 r 1 r 2 (4) (5) (6) 16 m 1 16 m 1 6
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 2 thermal characteristics characteristic symbol max unit mun5316dw1 (sot?363) one junction heated total device dissipation t a = 25 c (note 1) (note 2) derate above 25 c (note 1) (note 2) p d 187 256 1.5 2.0 mw mw/ c thermal resistance, (note 1) junction to ambient (note 2) r ja 670 490 c/w mun5316dw1 (sot?363) both junction heated (note 3) total device dissipation t a = 25 c (note 1) (note 2) derate above 25 c (note 1) (note 2) p d 250 385 2.0 3.0 mw mw/ c thermal resistance, (note 1) junction to ambient (note 2) r ja 493 325 c/w thermal resistance, (note 1) junction to lead (note 2) r jl 188 208 c/w junction and storage temperature range t j , t stg ?55 to +150 c nsbc143tpdxv6 (sot?563) one junction heated total device dissipation t a = 25 c (note 1) derate above 25 c (note 1) p d 357 2.9 mw mw/ c thermal resistance, junction to ambient (note 1) r ja 350 c/w nsbc143tpdxv6 (sot?563) both junction heated (note 3) total device dissipation t a = 25 c (note 1) derate above 25 c (note 1) p d 500 4.0 mw mw/ c thermal resistance, junction to ambient (note 1) r ja 250 c/w junction and storage temperature range t j , t stg ?55 to +150 c 1. fr?4 @ minimum pad. 2. fr?4 @ 1.0 x 1.0 inch pad. 3. both junction heated values assume total power is sum of two equally powered channels.
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 3 electrical characteristics (t a = 25 c both polarities q 1 (pnp) and q 2 (npn), unless otherwise noted) characteristic symbol min typ max unit off characteristics collector?base cutoff current (v cb = 50 v, i e = 0) i cbo ? ? 100 nadc collector?emitter cutoff current (v ce = 50 v, i b = 0) i ceo ? ? 500 nadc emitter?base cutoff current (v eb = 6.0 v, i c = 0) i ebo ? ? 1.9 madc collector?base breakdown voltage (i c = 10 a, i e = 0) v (br)cbo 50 ? ? vdc collector?emitter breakdown voltage (note 4) (i c = 2.0 ma, i b = 0) v (br)ceo 50 ? ? vdc on characteristics dc current gain (note 4) (i c = 5.0 ma, v ce = 10 v) h fe 160 350 ? collector?emitter saturation voltage (note 4) (i c = 10 ma, i b = 0.3 ma) v ce(sat) ? ? 0.25 vdc input voltage (off) (v ce = 5.0 v, i c = 100 a) (npn) (v ce = 5.0 v, i c = 100 a) (pnp) v i(off) ? 0.6 0.58 ? vdc input voltage (on) (v ce = 0.2 v, i c = 10 ma) (npn) (v ce = 0.2 v, i c = 10 ma) (pnp) v i(on) ? 0.9 1.0 ? vdc output voltage (on) (v cc = 5.0 v, v b = 2.5 v, r l = 1.0 k ) v ol ? ? 0.2 vdc output voltage (off) (v cc = 5.0 v, v b = 0.5 v, r l = 1.0 k ) v oh 4.9 ? ? vdc input resistor r1 3.3 4.7 6.1 k resistor ratio r 1 /r 2 ? ? ? product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 4. pulsed condition: pulse width = 300 msec, duty cycle 2%. figure 1. derating curve ambient temperature ( c) 125 100 75 50 25 0 ?25 ?50 0 50 100 150 200 250 400 p d , power dissipation (mw) 150 (1) (2) (1) sot?363; 1.0 x 1.0 inch pad (2) sot?563; minimum pad 350 300
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 4 typical characteristics ? npn transistors mun5316dw1, nsbc143tpdxv6 figure 2. v ce(sat) vs. i c figure 3. dc current gain i c , collector current (ma) i c , collector current (ma) 40 30 20 50 10 0 0.01 0.1 1 100 10 1 1 10 100 1000 figure 4. output capacitance figure 5. output current vs. input voltage v r , reverse voltage (v) v in , input voltage (v) 50 40 30 20 10 0 0 0.4 0.8 1.2 1.6 2.0 3.2 4 3 2 1 0 0.1 1 10 100 figure 6. input voltage vs. output current i c , collector current (ma) 40 30 50 20 10 0 0.1 1 10 100 v ce(sat) , collector?emitter voltage (v) h fe , dc current gain c ob , output capacitance (pf) i c , collector current (ma) v in , input voltage (v) i c /i b = 10 150 c ?55 c 25 c v ce = 10 v 150 c ?55 c 25 c f = 10 khz i e = 0 a t a = 25 c v o = 5 v 150 c ?55 c 25 c v o = 0.2 v 150 c ?55 c 25 c 0.01 2.4 2.8
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 5 typical characteristics ? pnp transistors mun5316dw1, nsbc143tpdxv6 150 c 25 c ?55 c figure 7. v ce(sat) vs. i c figure 8. dc current gain figure 9. output capacitance figure 10. output current vs. input voltage v in , input voltage (v) v r , reverse voltage (v) figure 11. input voltage vs. output current i c , collector current (ma) i c , collector current (ma) 1 0.1 50 40 20 10 0 i c , collector current (ma) 10 0 10 1 100 10 1 1000 v ce(sat) , collector?emitter volt- age (v) h fe , dc current gain 6 50 40 30 20 10 0 0 c ob , output capacitance (pf) 2 4 8 100 5 4 3 2 1 0 0.001 1 10 i c , collector current (ma) 100 30 20 10 0 0.1 1 40 50 v in , input voltage (v) 0.01 0.01 0.1 30 10 v ce = 10 v f = 10 khz l e = 0 a t a = 25 c v o = 5 v v o = 0.2 v 5 1 3 7 9 i c /i b = 10 150 c 25 c ?55 c 150 c 25 c ?55 c 150 c 25 c ?55 c 10
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 6 package dimensions sc?88/sc70?6/sot?363 case 419b?02 issue y notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimensions d and e1 do not include mold flash, protrusions, or gate burrs. mold flash, protru- sions, or gate burrs shall not exceed 0.20 per end. 4. dimensions d and e1 at the outermost extremes of the plastic body and datum h. 5. datums a and b are determined at datum h. 6. dimensions b and c apply to the flat section of the lead between 0.08 and 0.15 from the tip. 7. dimension b does not include dambar protrusion. allowable dambar protrusion shall be 0.08 total in excess of dimension b at maximum material condi- tion. the dambar cannot be located on the lower radius of the foot. c ddd m 123 a1 a c 654 e b 6x dim min nom max millimeters a ??? ??? 1.10 a1 0.00 ??? 0.10 ddd b 0.15 0.20 0.25 c 0.08 0.15 0.22 d 1.80 2.00 2.20 ??? ??? 0.043 0.000 ??? 0.004 0.006 0.008 0.010 0.003 0.006 0.009 0.070 0.078 0.086 min nom max inches 0.10 0.004 e1 1.15 1.25 1.35 e 0.65 bsc l 0.26 0.36 0.46 2.00 2.10 2.20 0.045 0.049 0.053 0.026 bsc 0.010 0.014 0.018 0.078 0.082 0.086 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* 0.65 0.66 6x dimensions: millimeters 0.30 pitch 2.50 6x recommended top view side view end view bbb h b seating plane detail a e a2 0.70 0.90 1.00 0.027 0.035 0.039 l2 0.15 bsc 0.006 bsc aaa 0.15 0.006 bbb 0.30 0.012 ccc 0.10 0.004 a-b d aaa c 2x 3 tips d e1 d e a 2x aaa h d 2x d l plane detail a h gage l2 c ccc c a2 6x
mun5316dw1, nsbc143tpdxv6 www. onsemi.com 7 package dimensions h e dim min nom max millimeters a 0.50 0.55 0.60 b 0.17 0.22 0.27 c d 1.50 1.60 1.70 e 1.10 1.20 1.30 e 0.5 bsc l 0.10 0.20 0.30 1.50 1.60 1.70 0.020 0.021 0.023 0.007 0.009 0.011 0.059 0.062 0.066 0.043 0.047 0.051 0.02 bsc 0.004 0.008 0.012 0.059 0.062 0.066 min nom max inches sot?563, 6 lead case 463a issue g e m 0.08 (0.003) x b 6 5 pl a c ?x? ?y? notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeters 3. maximum lead thickness includes lead finish thickness. minimum lead thickness is the minimum thickness of base material. d e y 12 3 4 5 l 6 1.35 0.0531 0.5 0.0197 mm inches scale 20:1 0.5 0.0197 1.0 0.0394 0.45 0.0177 0.3 0.0118 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* h e 0.08 0.12 0.18 0.003 0.005 0.007 on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 dtc143tp/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative
|
