www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 1086 a smd - 7 m arking ? hdf7g19 prepared checked approve d ? d a t e 200 6 - 5 - 1 1 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . mod ify content ? remark
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 8 1. scope this specification shall cover the characteristics of saw filter with f1086as 7 used digital television 2. electrical specification dc voltage vdc> 0v operation temperature - 40c~+85c storage temperature - 40c~+85c rf power dissipation 0 dbm(source impedance 200) electronic characteristics 2 - 1.typical frequency response 2 - 2.electrical characteristic s par number hdf1086as 7 unit norminal center frequency(fo) 1086 mhz insertion loss: 500.00~fc - 85.00mhz fc - 98 .00 ~ - 84.00 mhz fc - 40 .00 ~ - 50.00 mhz fc4.00mhz fc+70.00~2000.00mhz 50.0 min. 50.0 min 40 .0 min 5.80 max. 50.0 min. db ripple (with fo 4.0mhz) 1.5 max. db input/output impedance 200 ohm
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 8 3. test circuit 4. dimension marking hdf 7g19 hd: brand f : filter 7 : smd - 7 g19 : no. 5. environmental characteristics 5 - 1 temperature cycling subject the device to a low temperature of - 45 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature o f +85 for 30 minutes.
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 8 then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 2 - 2 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2 - 2 . 5 - 3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be cov ered with new solder. it shall meet the specifications in 2 - 2 . 5 - 4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2 - 2 . 5 - 5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 2 - 2 . 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component ma y be soldered. please avoid soldering another part of component. 7 . packing 7 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 7 .2 reeling qua ntity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below.
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 8 (2) label device name user product name quantity lot no. (3) leader pa rt and vacant position specifications. 8 . tape specifications 8 .1 tensile strength of carrier tape: 4.4n/mm width 8 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 8 [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2] [unit:mm] a b c d e w t r
saw filter hdf 1086a s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 8 ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
