d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 1 of 6 www.murata-ps.com www.murata-ps.com/support for full details go to www.murata-ps.com/rohs $ features ? ? 1600w output power ? ? 1.6"(1u) x 14.0" x 4.0" (41.0mm x 355.6mm x 101.6mm) ? ? 54vdc main; poe compatible ? ? 12v sb output ? ? pmbus? power management bus supported by dual redundant i2c interfaces. ? ? n+1 redundancy capable; hot swap (up to 8 modules in parallel) ? ? active current sharing on 54vdc main output; integral bidirectional mosfet output isolation device ? ? over-voltage, over-current; over-temperature protection ? ? internal variable speed cooling fans ? ? 20ms full cycle hold up ? ? rohs compliant ordering guide model number power output high line ac power output low line ac main output standby output air? ow d1u4-w-1600-54-hb4c 1600w 1200w 54v 12v back to front d1u4-w-1600-54-hb3c front to back input characteristics parameter conditions min. typ. max. units input voltage operating range 90 115/230 264 vac input frequency 47 50/60 63 hz turn-on input voltage ramp up 81 89 vac turn-off input voltage ramp down 70.5 78.0 maximum current @ vin = 200vac 1600w 10 arms maximum current @ vin = 90vac 1200w 15 inrush current cold start between 0 to 1ms 100 apk power factor at 230vac; fl 0.95 output voltage characteristics output voltage parameter conditions min. typ. max. units 54v voltage set point 54v vdc line & load regulation 52.38 55.62 output current 0 30 a ripple voltage & noise 1 20mhz bandwidth 540 mvp-p load capacitance 3800 24,000 f 12v voltage set point 12 vdc line & load regulation 11.64 12.36 output current 0 2 a ripple voltage & noise 1 20mhz bandwidth 33 mvp-p load capacitance 1530 f 1 ripple and noise are measured with a parallel combination of a 0.1f ceramic capacitor and 2 x 270f oscon capacitors on each of the power module outputs measurement nodes. see test set up diagram below. product overview the d1u4-w-1600-54-hbxc is a 1600w power factor corrected (pfc) front end power module intended for hot swap redundant systems. there is a main output of 54vdc (? oating with respect to chassis ground) and a 12vdc standby/ bias output (that is present whenever the incoming ac source is applied. the form factor is suitable for 1ru chassis enclosures and is designed to deliver reliable bulk dc power to servers, workstations, storage systems, poe switches or any 54vdc distributed power architecture requiring high power density. the high ef? ciency design supports speed controlled dual dc fans in a thermally optimized package that is self-pro- tecting and able to auto recover from over-current and over-temperature events. visual status information is provided via front panel mounted led indicators in addition to hardware logic signals and a pmbus? management interface. cb test certi cate and test report pm www.murata-ps.com / en / 3d / acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l www.murata- p s.com/en/3d/acdc.htm l www.murata-ps.com / en / 3d / acdc.htm l available now at www.murata-ps.com/en/3d/acdc.html
d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 2 of 6 www.murata-ps.com/support ripple measurement output characteristics parameter conditions min. typ. max. units remote sense remote sense is not enabled on these variants due to the system control feature and the relatively wide line & load regulation window. ef? ciency 230vac (excluding fan) 90 % output rise (monotonic) 10% to 95% rise time overshoot less than 10% for all outputs; no negative transition at turn off. startup time ac ramp up 3 s ps_on activation 250 ms transient response 54vdc 50% step (50-100%; 100%-50%) load; 1a/s 2700 mv 12vsb 1a/s 250 current sharing accuracy (up to 8 in parallel) at 100% load 10 % hot swap transients 5% hold up time 100% load 230vac nominal 20 ms environmental characteristics parameter conditions min. typ. max. units storage temperature range non-condensing -40 70 c operating temperature range 050 operating humidity non-condensing 10 90 % storage humidity 590 altitude 3000 m shock non-operating 30 g operational vibration operational, 0.5g; 5-500hz mtbf telcordia sr-332 40c 630 k hours safety approvals can/csa-c22.2 no.60950-1-07 am 1:2011 ansi/ul 60950-1-2011 iec60950-1:2005 (2nd ed)+a1:2009 and en60950-1:2006/a11:2009/a1:2010/a12:2011 cqc gb4943,1-2011 input fusing internal 20a/250v rated fast blow in ac line weight 4.63/2.1 lbs/kg power supply ac phase load box a cg r ou n d oscilloscope 20mhz bw bnc to bnc shielded cable 2x270uf oscon general notes: 1. load the outputs at specified minimum output current. 2. connect the probe as shown with the input tip and ground as short as possible. 3. take all measurements 4. repeat the measurements with the outputs at specified maximum output current. 0.1uf ceramic
d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 3 of 6 www.murata-ps.com/support protection characteristics output voltage parameter conditions min. typ. max. units 54v over-temperature auto re-start 55 65 c over-voltage latching 57 60 v over-current constant current for 200ms followed by latch 33 39 a 12vsb over-voltage latching 13.5 14.4 v over-current latching 2.2 2.6 a isolation characteristics parameter conditions min. typ. max. units insulation safety rating / test voltage input to output - reinforced 3000 vrms input to chassis - basic 1500 vrms isolation output to chassis (ground) 2250 vdc grounding the main 54vdc output shall be provided with isolation between the output and chassis ground. it shall be able to withstand the following tests: a) 1500vrms at 50hz to 60hz for 60s. b) 2250 vdc for 60s. there shall be no insulation breakdown during the test as de? ned in sub clause 5.2.2 of iec 60950-1:2001. the resistance after the test should be at least 2m ohms when measured at 500vdc. the vrtn should be isolated from the 12vsb return and the power module shall support poe electrical isolation requirements. status indicators and control signals status conditions description led indicators off no ac applied to any power module in host system off no ac applied to this power module only blinking green ac present & vstandby on green 54vdc and vstandby on and ok blinking amber power module warning amber power module failure i 2 c and pmbus there is provision for the connection of dual i2c buses for redundancy. this enables two master devices to connect to single slave device(s) within the power module. the power module is provided with a pmbus management interface that provides status, measurement and control data. sys_contr host system control input that can be used to turn on/off the main 54vdc output. emissions and immunity characteristic standard compliance input current harmonics iec/en 61000-3-2 complies with class a limits voltage fluctuation & flicker iec/en 61000-3-3 complies conducted emissions fcc 47 cfr part 15; cispr 22; en55022 complies to class a with 6db margin radiated emissions complies to class a with 6db margin esd immunity iec/en 61000-4-2; 4kv contact discharge; criteria a 8kv operational air discharge; criteria a 15kv non-operational air discharge, criteria a radiated field immunity iec/en 61000-4-3 complies electrical fast transients/burst immunity iec/en 61000-4-4 complies surge immunity iec/en 61000-4-5 1kv/2kv; criteria a performance rf conducted immunity iec/en 61000-4-6 3vac, 80% am, 1khz; criteria a performance magnetic field immunity iec/en 61000-4-8 3a/m voltage dips & interruptions iec/en 61000-4-11 complies
d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 4 of 6 www.murata-ps.com/support output connector and signal specification dc and signal connector: fci # 51732-028-lf blade/ pin assignment signal name description logic level current p1, p2, p3 vout main 54v output voltage p4, p5, p6 vrtn main 54v output voltage, return a2 vout_sense + main 54v output voltage sense + a3 vout_sense - main 54v output voltage sense - c2, c3, d3 vstby standby voltage output c4, c5, d5 vstby return standby voltage output, return b1 i_share analogue active current share bus 0v to 8v -4ma/+5ma d1 ac_ok ac source voltage ok signal (internally pull up to vstandby by 10k (3.3v & 5v vstandby). 10k (to 5v) for 12 vstandby >2.4v (active, ok) <0.4v (not ok) +4ma -2ma d2 p_good power good signal (internally pull up to vstandby by 10k (3.3v & 5v vstandby). 10k (to 5v) for 12 vstandby >2.4v (active, good) <0.4v (not good) +4ma -2ma a1 ps_kill floating pin; will turn off main output >2.4v high <0.4v low b5 ps_present tied internally to vstandby return 0v c1 ps_on_l internally pull up to vstandby by 1k; can be driven with open drain/collector switches >2.4v high <0.4v low a4 i 2 c_sda0 (sda) i 2 c compatible data bus >2.4v high <0.4v low a5 i 2 c_scl0 (scl) i 2 c compatible data bus b3 i 2 c_sda1 (sda) i 2 c compatible data bus b4 i 2 c_scl1 (scl) i 2 c compatible data bus b2 sys_contr host system control that can be used to turn on/off the main 54v dc output via an internal output switch within power module. low turns on output switch mating connector supplier press fit, straight press fit, right angle solder straight solder right angle fci -- -- -- 51762-1060-2000-ablf p1 p2 p3 p4 p5 p6 x1 x2 x3 x4 x5 v out v out v out v rtn v rtn v rtn ac_ok p_good v_stby no user connection v_stby return d ps_on v_stby v_stby v_stby return v_stby return c i_share sys_contr i 2 c data2 i 2 c clock2 ps_present b ps_kill vout sense+ vout sense- i 2 c data1 i 2 c clock1 a
d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 5 of 6 www.murata-ps.com/support wiring diagram for output current sharing notes 1. main 54vdc output: analogue active share bus. the ishare bus (pin b1) must be connected on all sharing modules. it is not required that the sense signals are connected to the remote load for current share to operate correctly. 2. up to eight (8) power modules can be connected in parallel (non-redundant) or n+1 con? guration. the current share bus is an alogue bi-directional (can source or sink current from the ishare bus). the voltage of the bus would measure 8vdc for a single power module at 100% load; for two (2) modules sharing a common load the ishare bus voltage would be 4v for a perfect 50/50 current share scenario. 3. vstandby output power modules can also be connected in parallel; however the combined available power is limited to that ava ilable from a single power module (12v; 2a; 24w) irrespective of the number of modules connected in parallel. vrtn sense + (main output remote sense) sense - vout - dotted lines show optional remote sense connections. optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. d1u4 ps_kill d1u4 b1 i_share ps_kill b1 sense - i_share vrtn vout sense + (main output remote sense) 54v load 12v standby load close switch (or fet, bjt or wire) to turn on +54v out a2 a2 a3 a3 p1 , p2, p3 p1, p2, p3 p4, p5, p6 p4, p5, p6 c2, c3, d3 c2, c3, d3 c4, c5, d5 c4, c5, d5 ps_on_l ps_on_l c1 c1 a1 a1 vstby vstby vsb return vsb return
d1u4-w-1600-54-hbxc ac-dc power supply cps_d1u4-w-1600-54-hbxc.a01 page 6 of 6 www.murata-ps.com/support murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained her ein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. speci? cations are subject to cha nge without notice. ? 2014 murata power solutions, inc. murata power solutions, inc. 11 cabot boulevard, mans? eld, ma 02048-1151 u.s.a. iso 9001 and 14001 registered this product is subject to the following operating requirements and the life and safety critical application sales policy: refer to: http://www.murata-ps.com/requirements/ mechanical dimensions ac input connector/inlet: iec 60320-c20 dimensions: 4.00" x 14.00"x 1.6" [101.6mm x 355.6mm x 41.0mm] optional accessories description part number d1u4-54 output interface connector card d1u4-54-conc application notes document number description link acan-52 d1u4-54-conc output connector card www.murata-ps.com/data/apnotes/acan-52.pdf ACAN-53 d1u4 communications protocol www.murata-ps.com/data/apnotes/ACAN-53.pdf all dimensions in mm 2.40 0.35 349.60 0.65 355.60 0.65 8.88 0.40 41.00 0.40 12.63 0.50 21.45 0.50 101.60 0.50 13.25 0.40 10.75 0.40 back to front airflow front to back airflow
|
