|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 4 1 5 e smd - 5 prepared checked approved ? d a t e 200 6 - 5 - 11 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . modify content ? remark saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 8 1. scope this specification shall cover the characteristics of saw filter with f4 1 5e used for the page system. 2. electrical specification dc voltage vdc 10v ac voltage vpp 10v50hz/60hz operation temperature - 4 0 to + 85 storage temperature - 45 to +85 rf power dissipation 0dbm electronic characteristics 2 - 1.typical frequency response 2 - 2.electrical characteristics part number f4 1 5 e unit nominal center frequency (fo) 4 1 5.0 mhz insertion loss 1. fo - 60~fo - 100 mhz 2. fo 3. .fo +70~ fo +100mhz 45min 4.5 max. 45min db ripple (with fo 12 .0mhz) 2.0max db - 3db pass band width 30min. mhz input/output impedance(nominal) 50// 100 balance /pf saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 8 3. test ci rcuit 4. dimension 5. environmental characteristics 5 - 1 high temperature exposure subject the device to +85 for 16 hours. then release the filter into the room conditions for 24 hours prior to the measurement. it shall fulfill the specificat ions in 2 - 2 . 5 - 2 low temperature exposure subject the device to - 4 0 for 16 hours. then release the device into the room conditions for 24 hours prior to the measurement. it shall fulfill the specifications in 2 - 2 . saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 8 5 - 3 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +8 5 for 30 minutes. then release the device into the room conditions for 24 hours prior to the me a surement. it shall meet the specifications in 2 - 2 . 5 - 4 resistance to solder heat dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for 10 1 sec. then release the device into the room conditions for 4 hours. the device shall meet the specifications in 2 - 2 . 5 - 5 solderability subject the de vice terminals into the solder bath at 245 5 for 5s, more than 95% area of the terminals must be covered with new solder. it shall meet the specifications in 2 - 2 . 5 - 6 mechanical shock drop the device randomly onto the concrete floor from the height o f 1m 3 times. the device shall fulfill the specifications in 2 - 2 . 5 - 7 vibration subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the device shall fulfill the specifications in 2 - 2 . 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of t he component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product s hall be packed properly not to be damaged during transportation and storage. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around the reel in the direction shown below. saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 8 (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications. 8. tape specifications 8.1 tensile strength of carrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 8 (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 8.00 0.10 2.00 0.10 ?1.50 ?1.0 0.25 0.25 0.05 1.65 0.10 4.04 0.10 4.10 0.10 [figure 2] saw filter hdf 4 1 5 e smd - 5 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 8 [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max. |
Price & Availability of HDF415ES5 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |