HEDS-9710, heds-9711 small optical encoder modules 360 ipi analog current output data sheet features ?? small size ?? two channel quadrature output ?? linear and rotary applications ?? no signal adjustment required ?? ttl compatible ?? wave solderable ?? lead free package ?? 15c to 45c operating temperature ?? single 5 v supply description the heds-971x is a high performance incremental encoder module. when operated in conjunction with either a codewheel or codestrip, this module detects rotary or linear position. the encoder consists of a lensed led source and a detector ic enclosed in a small c-shaped plastic package. due to a highly collimated light source and a unique photodetector array, the module is extremely tolerant to mounting misalignment. the two channel analog outputs and 5 v supply input are accessed through four solder plated leads located on 2.54 mm (0.1 inch) centers. the standard heds-971x is designed for use with an appro priate optical radius codewheel or linear codestrip. other options are available. please contact the factory for more information. applications the heds-971x provides sophisticated motion detection, making closed loop control, very cost competitive. typical applications include printers, plotters, copiers and offi ce automation equipment. block diagram resistor lens led comparators photo- diodes signal processing circuitry + C a 2 a emitter section code wheel detector section + C b 4 gnd 1 v cc 3 b channel a channel b
2 theory of operation an heds-971x is a c-shaped emitter/detector module. coupled with a codewheel, it translates rotary motion into a two-channel digital output, coupled with a codestrip; it translates linear motion into digital outputs. as seen in the block diagram, the module contains a single light emitting diode (led) as its light source. the light is collimated into parallel beam by means of a single lens located directly over the led. opposite the emitter is the integrated detector circuit. this ic consists of photodetec- tors and a signal processing circuitry necessary to produce the digital waveforms. the codewheel/codestrip moves between the emitter and detector, causing the light beam to be interrupted by the pattern of spaces and bars on the codewheel/ codestrip. the photo diodes, which detect these interrup- tions, are arranged in a pattern that corresponds to the radius and count density of the codewheel/codestrip. these photodiodes are also spaced such that a light period on one pair of detectors corresponds to a dark period on the adjacent pairs of detectors. the photodiode out puts are fed through the signal processing circuitry. two comparators receive these signals and produce the fi nal outputs for channels a and b. due to this integrated phasing technique the output of channel a is in quadra- ture with channel b (90 degrees out of phase). defi nitions count (n): the number of bar and window pairs or counts per revolution (cpr) of the codewheel, or the number of lines per inch of the codestrip (lpi). 1 shaft rotation = 360 degrees = n cycles 1 cycle (c) = 360 electrical degrees, equivalent to 1 bar and window pair. pulse width (p): the number of electrical degrees that an output is high during one cycle, nominally 180e or ? a cycle. pulse width error ( ? p): the deviation in electrical degrees of the pulse width from its ideal value of 180e. state width (s): the number of electrical degrees between a transition in the output of channel a and the neighboring transition in the output of channel b. there are 4 states per cycle, each nominally 90e. state width error ( ? s): the deviation in electrical degrees of each state width from its ideal value of 90e. phase ( ? ): the number of electrical degrees between the center of the high state on channel a and the center of the high state on channel b. this value is nominally 90e for quadrature output. phase error ( ?? ): the deviation in electrical degrees of the phase from its ideal value of 90e. direction of rotation: when the codewheel rotates in the counter-clockwise direction (as viewed from the encoder end of the motor), channel a will lead channel b. if the codewheel rotates in the clockwise direction, channel b will lead channel a. optical radius (rop): the distance from the codewheels center of rotation to the optical center (o.c) of the encoder module. angular misalignment error (e a ): angular misalignment of the sensor in relation to the tangential direction. this applies for both rotary and linear motion. mounting position (r m ): distance from motor shaft center of rotation to center of alignment tab receiving hole.
3 absolute maximum ratings parameter symbol min. max. units notes storage temperature t s C40 85 c operating temperature t a 0 85 c supply voltage v cc C0.5 7 volts soldering temperature t sol 260 c t 5 sec recommended operating conditions parameter symbol min. typ. max. units notes temperature t a 15 45 c supply voltage v cc 4.8 5.0 5.2 volts ripple < 100 m vp-p count frequency f 40 khz velocity (rpm) x n/60 electrical characteristics electrical characteristics over the recommended operating conditions. typical values at 25c. parameter symbol min. typ. max. units notes supply current i cc 17 40 ma waveform defi nition iap ibp ibm iam a b a b analog digital p p s1 s2 s3 s4
4 test parameter defi nitions parameter symbol defi nition units ip analog peak the absolute value in a of the magnitude of the analog signal iap,ibp, (i.e. one sided rating). iam, ibm ipp analog peak the peak to peak signal magnitude in ma of the analog signal. iapp, ibpp to peak iapp/ibpp analog peak the ratio of a channel peak analog signal to b channel peak to peak to peak ratio analog signal. ioff set analog off set the off set in ? a from the mid-point of the analog peak to peak signal to zero current. state width state width the number of electrical degrees between a transition in channel a state 1 and the neighboring transition in channel b. there are 4 states per state 2 cycle, each nominally 90 e. state 3 the transitions are determined by where the analog signal crosses the zero point. state 4 state width state width the deviation in electrical degrees of each state width from its ideal error error value of 90 e. pulse width pulse width the number of electrical degrees that an analog output is greater than zero during one cycle. this value is nominally 180 e or ? cycle. pulse width pulse width the deviation in electrical degrees of each pulse width from its error error ideal value of 180 e.
5 encoder characteristics encoding characteristics over the recommended operating conditions and mounting conditions. these characteristics do not include codewheel/codestrip contribution. the typical values are average over the full rotation of the codewheel. parameter units min. max. state width error e C40 40 phase error e C40 40 ipp ? a 25 95 ippa/ippb C 0.93 1.16 ioff set ? a C7 7 linearity error C 0 12 crossing (avg) ? a 9 35 mounting considerations parameter units tolerance radial microns 200 tangential microns 400 gap microns 50 C 460 o.r. mm 20.2 cpr count 1800 mounting consideration note: these dimensions include shaft end play and codewheel warp. all dimensions for mounting the module/codestrip should be measured with respect to the two mounting posts, shown above. dimensions in millimeters (inches). max. rop rm rm = rop C 0.14 (0.006) c l of alignment tab 5.32 (0.209) 4.23 0.13 (0.17 0.005) see note 1 max. 6.30 (0.248) min. 6.50 (0.256) 2x r hole min. 2.03 (0.080) deep min. 1.0 (0.039) min. 2.03 (0.080) deep min. 1.0 (0.039) ?
6 recommended codewheel and codestrip characteristics analog encoder interface circuit the circuit shown can be used to convert the current to voltage output. resistor value r1 and capacitor c are specifi ed to attain required gain and low pass fi ltering which are application specifi c. the gain is chosen to attain maximum output swing and not clamping the op-amp. v ref should be set to 1.4 v 0.2 v. a 0.1 ? f bypass capacitor is recommended to be placed within 1 cm of the encoder for optional power supply noise rejection. output are high impedance (typical 1m ohm) and susceptible to emi. parameter symbol min. max. units notes window/bar ratio ww/wb 0.9 1.1 window length (rotary) lw 1.80 2.30 mm (0.071) (0.091) (inch) absolute maximum codewheel radius (rotary) rc rop + 3.40 mm includes eccentricity (rop + 0.134) (inch) errors center of post to inside edge of window w1 1.04 mm (0.041) (inch) center of post to outside edge of window w2 0.76 mm (0.030) (inch) center of post to inside edge of codestrip l 3.60 mm (0.142) (inch) lw wb wb rop w1 w2 rc ww ww max 3.4 (0.134) l i a-in v ref i+ + C c r1 v a i b-in v ref i+ + C c r1 v b v ref = 1.4 v 0.2 v (dc)
7 ordering information heds C 971 option lead confi gurations 0 C straight leads 1 C bent leads bracket option 50 resolution 1 C 360 lpi package dimensions option 50 bent version C option 50 xxxxx yyww c x 50 agilent 8.7 6.4 0.14 (optical center) 2x ? 2.00 0.02 1.4 5.0 3.9 r 1.4 10.1 7.5 4.2 3.90 0.10 0.8 1.70 0.15 4.2 3.0 9.8 1.8 3.8 0.5 20.2 0.5 15.0 8.4 part # (refer -05) c = country of origin marking (refer -05 for details) date code 12.6 0.5 7.0 option code pin 1 id ch b v cc ch a gnd lead thickness = 0.25 mm lead pitch = 2.54 mm 10.8 0.5 5.5 0.3 r 2.6 xxxxx yyww c x 50 agilent 8.7 6.4 0.14 (optical center) 2x ? 2.00 0.02 r 2.6 1.4 5.0 3.9 r 1.4 10.1 7.5 4.2 3.90 0.10 0.8 1.70 0.15 9.2 0.3 5 typ. 4.2 3.0 0.3 6.0 9.8 1.8 10.8 0.5 3.8 0.5 20.2 0.5 15.0 8.4 part # (refer -05) date code 12.6 0.5 7.0 option code pin 1 id ch b v cc ch a gnd lead thickness = 0.25 mm lead pitch = 2.54 mm c = country of origin marking (refer -05 for details)
for product information and a complete list of distributors, please go to our web site: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies in the united states and other countries. data subject to change. copyright ? 2005-2012 avago technologies. all rights reserved. obsoletes 5989-0702en av02-3652en - june 21, 2012 nominal parameter min. max. values units a solder pot temperature na 260 250 C 260 oc b preheat zone temperature 85 120 100 C 120 oc c dip in time 5 7 5 sec d solder pot zone (pcb top) na na na oc e solder pot zone (encoder lead) 200 na 200 oc wave soldering profi le pb-free wave soldering profi le std-profi le 120c/20 sec max. cool down flow 260c x-axis 7 sec max. y-axis
|
