TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 1 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ir sensor module for remote control systems mechanical data pinning: 1, 4 = gnd, 2 = v s , 3 = carrier out ordering code taping: TSMP77000tt - top view taped TSMP77000tr - side view taped features ? photo detector and preamplifier in one package ? ac coupled response from 20 khz to 60 khz, all data formats ? improved shielding agai nst electrical field disturbance ? ttl and cmos compatibility ? output active low ? supply voltage 2.5 v to 5.5 v, typically the device works in the range between 2.0 v and 5.5 v ? carrier out signal for code learning functions ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 description the TSMP77000 is a two lens miniaturized sensor for receiving various kinds of mo dulated ir signals. two pin diodes and a preamplifier are assembled on a lead frame, the epoxy package is designed as an ir filter. the modulated output signal, carrier out, can be used for code learning applications. this component has not been qualified according to automotive specifications. block diagram application circuit 1 2 3 4 20953 1 2 3 4 209 5 3 parts table carrier frequency 20 khz to 60 khz TSMP77000 package heimdall pinning 1, 4 = gnd, 2 = v s , 3 = carrier out dimensions (mm) 6.8 w x 3.0 h x 3.2 d mounting smd application code learning tia amp signal shaping 3 carrier out 19746-3 1, 4 gnd 2 v s c 1 = 4.7 f tsmpxxxx out gnd circuit c r 1 = 100 + v s gnd transmitte r with tsalxxxx v s v o 19750-2 r 2 = 4.7 k r 1 + c 1 recommended to suppress power supply disturbances. r 2 recommended to get faster slopes and a correct high level of the output pulses.
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 2 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress ratin g only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect the device reliability. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - testsignal absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit supply voltage (pin 2) v s -0.3 to +6 v output voltage (pin 3) v o -0.3 to (v s + 0.3) v output current (pin 3) i o 5ma junction temperature t j 100 c storage temperature range t stg -25 to +85 c operating temperature range t amb -25 to +85 c electrical and optical characteristics carrier out (t amb = 25 c, unless otherwise specified, v s = 3 v) parameter test condition symbol min. typ. max. unit supply current (pin 2) e v = 0 i sd 0.55 0.7 0.9 ma supply voltage v s 2.5 - 5.5 v transmission distance e v = 0, test signal see fig. 1, ir diode tsal6200, i f = 400 ma d-5-m output voltage low (pin 3) i osl = 0.5 ma, test signal see fig. 1 v osl --250mv minimum irradiance v s = 3 v, (20 khz to 60 khz) e e min. -1225mw/m 2 maximum irradiance test signal see fig. 1, (20 khz to 60 khz) e e max. 50 80 - w/m 2 directivity angle of half transmission distance ? 1/2 - 50- deg output accuracy f c = 20 khz to 60 khz, e e = 25 mw/m 2 to 50 w/m 2 , testsignal see fig. 1, ber 2% n carrier pulses input burst length - 1 cycle input burst length input burst length + 1 cycle counts carrier cycle (26.3 s in ca s e of 38 khz) delay time t d optical bur s t (input s ignal) output voltage
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 3 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 2 - relative spectral sensitivity vs. wavelength fig. 3 - horizontal directivity fig. 4 - vertical directivity - wavelength (nm) s( ) rel - relative spectral sensitivity 22102 0 0.2 0.4 0.6 0.8 1.0 700 800 900 1000 1100 0.8 0.9 1.0 0.6 0.4 0.2 0 0 30 10 20 40 50 60 70 80 d rel - relative transmission distance 21427 0.8 0.9 1.0 0 30 10 20 40 50 60 70 80 d rel - relative transmission distance 21428 0.6 0.4 0.2 0
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 4 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters assembly instructions reflow soldering ? reflow soldering must be done within 72 h while stored under a max. tempe rature of 30 c, 60 % rh after opening the dry pack envelope ? set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. exercise extreme care to keep the maximum temperature below 260 c. the temperature shown in the profile means th e temperature at the device surface. since there is a temperature difference between the component and the circuit bo ard, it should be verified that the temperature of the device is accurately being measured ? handling after reflow should be done only after the work surface has been cooled off manual soldering ? use a soldering iron of 25 w or less. adjust the temperature of the so ldering iron below 300 c ? finish soldering within 3 s ? handle products only after the temperature has cooled off 6.6 0.1 3.2 1.27 3 x 1.27 = 3.81 (4 x) 2.2 (1) 1.2 0.2 (2.2) 2.2 (3.4) (r1.3) 2.5 0.5 0.1 0.8 (1.8) 3 pick and place area propo s ed pad layout from component s ide (for reference only) technical drawing s according to din s pecification s not indicated tolerance s 0.15 drawing-no.: 6.550-5297.01-4 i ss ue: 4; 13.09.11 marking area tool s eparation line (0.635) (1.65) 0.8 1.8 1.27 3 x 1.27 = 3.81 (3 x) mold re s idue mold re s idue 6.8 22608
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 5 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 vishay lead (pb)-free reflow solder profile taping version tsmp..tr dimensions in millimeters 0 50 100 150 200 250 300 0 50 100 150 200 250 300 t (s) t (c) 255 c 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 20 s max. ramp up 3 c/s max. ramp down 6 c/s max. 2 cycles allowed 19800 drawing-no.: 9.700-5337.01-4 i ss ue: 2; 06.10.15 2 1.75 7.5 16 8 4 3.6 0.3 ? 1.5 min. ? 1.5 direction of feed 1.34 ref. technical drawing s according to din s pecification s
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 6 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsmp..tt dimensions in millimeters 0.3 3.65 16 7.5 1.75 ? 1.5 ? 1.5 2 8 4 drawing-no.: 9.700-5338.01-4 i ss ue: 4; 12.06.13 technical drawing s according to din s pecification s direction of feed
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 7 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 reel dimensions in millimeters leader and trailer dimensions in millimeters cover tape peel strength according to din en 60286-3 0.1 n to 1.3 n 300 mm/min. 10 mm/min. 165 to 180 peel angle label standard bar code labels for finished goods the standard bar code labels are product labels and used for identification of goods. th e finished goods are packed in final packing area. the standard packing units are labeled with standard bar code labels be fore transported as finished goods to warehouses. the labels are on each packing unit and contain vishay semicond uctor gmbh specific data. 16734 trailer leader no devices min. 200 min. 400 start end devices 96 11818 no devices
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 8 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dry packing the reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. final packing the sealed reel is packed in to a cardboard box. a secondary cardboard box is used for shipping purposes. recommended meth od of storage dry box storage is recommended as soon as the aluminum bag has been opened to preve nt moisture absorption. the following conditions should be observed, if dry boxes are not available: ? storage temperature 10 c to 30 c ? storage humidity 60 % rh max. after more than 72 h under these conditions moisture content will be too high for reflow soldering. in case of moisture absorptio n, the devices will recover to the former condition by drying under the following condition: 192 h at 40 c + 5 c / - 0 c and < 5 % rh (dry air / nitrogen) or 96 h at 60 c + 5 c and < 5 % rh for all device containers or 24 h at 125 c + 5 c not suitable for reel or tubes. an eia jedec ? standard j-std-020 level 4 label is included on all dry bags. eia jedec standard j- std-020 level 4 label is included on all dry bags vishay semiconductor gmbh standard bar code product label (finished goods) plain writting abbreviation length item-description - 18 item-number ino 8 selection-code sel 3 lot-/serial- number batch 10 data-code cod 3 (yww) plant-code ptc 2 quantity qty 8 accepted by acc - packed by pck - mixed code indica tor mixed code - origin xxxxxxx+ company logo long bar code top type length item-number n 8 plant-code n 2 sequence-number x 3 quantity n 8 total length - 21 short bar code bottom type length selection-code x 3 data-code n 3 batch-number x 10 filter - 1 total length - 17 aluminum bag label reel 15973 caution this bag contains moisture-sensitive devices 1. shelf life in sealed bag: 12 months at < 40 c and < 90 % relative humidity (rh) 2. after this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 c) must be 2a. mounted within 72 hours at factory condition of < 30 c/60 % rh or 2b. stored at < 5 % rh 3. devices require baking befor mounting if: humidity indicator card is > 10 % when read at 23 c 5 c or 2a. or 2b. are not met. 4. if baking is required, devices may be baked for: 192 hours at 40 c + 5 c/- 0 c and < 5 % rh (dry air/nitrogen) or 96 hours at 60 c 5 c and < 5 % rh for all device containers or 24 hours at 125 c 5 c not suitable for reels or tubes bag seal date: (if blank, see barcode label) note: level and body temperature defined by eia jedec standard j-std-020 4 level 22522
TSMP77000 www.vishay.com vishay semiconductors rev. 1.6, 14-apr-16 9 document number: 82478 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 esd precaution proper storage and handling pro cedures should be followed to prevent esd damage to the devices especially when they are removed from the antistatic shielding bag. electrostatic sensitive devices warning la bels are on the packaging. vishay semiconductors standard bar code labels the vishay semiconductors st andard bar code labels are printed at final packing areas. the labels are on each packing unit and contain vishay semiconductors specific data. 22178
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
