product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 1 ERF5 series C socket , vertical orientation erm5 series C terminal , vertical orientation other configurations available for: p erpendicular board - to - board applications rugged features / end options p ackaging options see www.samtec.com for more information.
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 2 1.0 scope 1.1 this specifi cation covers performance, test ing and quality requirements for s amtec s erf 5 /erm 5 series 0,5 0 mm (.0197) pitch edge rate ? rugged high speed socket and terminal strip . all information contai ned i n this specification is for a 7 mm mated height vertical configuration unless otherwise noted. 2.0 detailed information 2.1 product prints, footprints, catalog pages, test reports and other specific, detailed information can b e found at www.samte c.com? ERF5 and www.samtec.co m? erm5 . 3.0 testing 3.1 current rating: 1.5 a (one pin powered per row) 3.2 voltage rating: 190 vac 3.3 operating temperature range: - 55c to +125c 3.4 operating humidity range: 90% to 95% (per eia - 364 - 31) 3.5 electrical: item test condition requirement status withstanding voltage eia - 364 - 20 (no flashover, sparkover, or b reakdown) 575 vac pass insulation resistance eia - 364 - 21 ( 1 000 m? minimum) 5 ,000 m? pass contact resistance (llcr) eia - 364 - 23 15 m? maximum (samtec defined)/ no damage pass 3.6 mechanical: item test condition requirement status durability eia - 364 - 09c 1 0 0 cycles pass random vibration eia - 364 - 28 condition v, letter b 7.56 g 'rms', 50 to 2000 hz, 2 hours per axis, 3 axis total , psd 0.04 visual inspection: no damage llcr: 15 m? maximum event detection: no interruption > 50 nanoseconds pass mechanical shock eia - 364 - 27 100 g, 6 milliseconds, sawtooth wave, 11 .3 fps, 3 shocks/direction, 3 axis (18 total shocks) visual inspection: no damage llcr: 15 m? maximum event detection: no interruption > 50 nanoseconds pass normal force eia - 364 - 04 30 g rams minimum for gold interface pass
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 3 3.7 environmental: item test c ondition requirement status thermal shock eia - 364 - 32 thermal cycles: 100 (30 minute dwell) hot temp: +85c cold temp: - 55c hot/cold transition: immediate visual inspection: no dam age llcr: 15 m? dwv: 575 v ac ir: > 100 ,000 m? pass thermal aging (temp life) eia - 364 - 17 test condition 4 @ 105c condition b for 250 hours visual inspection: no damage llcr: 15 m? dwv: 575 vac ir: > 100 ,000 m? pass cyclic humidity eia - 364 - 31 test temp: +25c to +65c relative humidity: 90 to 95% test duration: 240 hours visual inspection: no damage llcr: 15 m? dwv: 575 vac ir: > 10 0 ,000 m? pass gas tight eia - 364 - 36 gas exposure: nitric acid vapor duration: 60 min. drying temp.: 50c +/ - 3c measurements: within 1 hour of exposure llcr: 15 m? pass
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 4 4.0 mated system 4.1 mated views mated view information can be found at link below: http://cloud.samtec.com/prints/erx5%20mated%20document - mkt.pdf 5.0 polarizing features 6.0 h igh speed performance 6.1 based on a 3 db insertion loss stack height single - ended signaling differential pair signaling 7 mm 1 3.5 ghz / 27 gbps 20 ghz / 40 gbps 10 mm 9 ghz / 18 gbps 8.5 ghz / 17 gbps 6.2 system i mpedance: 50 ohm for single - ended and 100 ohm f or differential pair
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 5 7.0 processing recommendations 7.1 mating a lignment r equirements: 7.1.1 maximum guidance /capture in applications where at least one half of the interface is free to float. 7.1.2 the parts can be rigidly misaligned by no more than 0 , 0 6 mm (. 00 2 ) in the x - and 0, 05 mm (.00 2 ) in the y - direction to ensure a good mate.
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 6 7.2 mating angle r equirements: the connector can be zippered in the longitudinal direction only. 7.2.1 7.2.2
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 7 7.3 due to variances in equipment, solder pastes and applications (board design, component density, etc.), samtec does not specify a recommended reflow profile for our connectors. the processing parameters provided by the solder paste manufacturer should be employed and can usually be found on their website. all of sam tecs surface mount components are lead free reflow compatible and compliant with the profile parameters detailed in ipc/jedec j - std - 020 e which requires that components be capable of withstanding a peak temperature of 260c as well as 30 seconds above 255 c. samtec recommended temperature profile ranges (smt) sn - pb eutectic assembly preheat/soak (100c - 150c) max ramp up rate reflow time (above 183c) peak temp time within 5c of 235c max ramp down rate time 25c to peak temp 60 - 120 sec. 3c/s max. 40 - 150 sec. 235c 20 sec. max. 6c/s max. 6 min. max. pb - free assembly preheat/soak (150c - 200c) max ramp up rate reflow time (above 217c) peak temp time within 5c of 260c max ramp down rate time 25c to peak temp 60 - 120 sec. 3c/s max. 40 - 150 sec. 2 60c 30 sec. max. 6c/s max. 8 min. max. 7.3.1 these guidelines should not be considered design requirements for all applications. samtec recommends testing interconnects on your boards in your proces s to guarantee optimum results. 7.4 maximum reflow passes: t he parts can withstand three reflow passes at a maximum component temperature of 260c.
product specification series: erf 5 / erm 5 0 , 5 0 mm (.0 197 ) edge r ate ? rugged high speed socket / terminal strip revision: d date: september 23, 2015 ? 2013 samtec, inc. page 8 7.5 stencil t hickness: the stencil thickness is .006 (0 ,1 5 mm) . 7.6 placement: machine placement of the parts is strongly recommended. 7.7 reflow environment: samtec recommend s the use of a low level oxygen environment (typically achieved through nitrogen gas infusion) in the reflow process to improve solderability. 7.8 hardware: board - to - board standoffs are recommended to provide a robust mechanical connection. samtec offers two different types: 7.8.1 traditional standoffs (so) C rigid design to statically support board - to - board applications. see options here: so - board stacking standoff 7.8.2 jack screw standoffs ( jso) C serve same function as traditional standoffs but unique, nested construction facilitates the mating and unmating process. this is especially helpful for multiple connector applications where the mating and unmating forces increase with the number o f connectors used. see options here: jso - jack screw standoffs 7.9 cleaning: samtec, inc. has verified that our connectors may be cleaned in accordance with the solvents and conditions des ignated in the eia - 364 - 11a standard. 8.0 additional resources 8.1 for additional mechanical testing or product information , contact our customer engineering support group at ces@samtec.com 8.2 for additional information on high speed performance testing, contact our signal integrity group at sig@samtec.com 8.3 for additional processing information, contact our interconnect processing group at ipg@samtec.com . 8.4 for rohs, reach or other environmental compliance information , contact our product environmental compliance group at pec@samtec.com use of product specification sheet this product specification sheet (pss) is a brief summary of information related to the product identified. as a summary, it should only be used for the limited purpose of considering the purchase/use of product. for specific, detailed information, includi ng but not limited to testing and pro duct footprint, refer to section 2.0 of this document and the links there provided to test reports and prints. this pss is the property of samtec, inc. (samtec) and contains proprietary information of samtec, our various licensors, or both . samtec does not grant express or implied rights or license under any patent, copyright, trademark or other proprietary rights and the use of the pss for building, reverse engineering or replication is strictly prohibited. by using the pss, the user agrees to not infri nge, directly or indirectly, upon any intellectual property rights of samtec and acknowledges that samtec, our various licensors, or both own all intellectual property therein. the pss is presented as is. while samtec makes every effort to present excell ent information, the pss is only provided as a guideline and does not, therefore, warrant it is without error or defect or that the pss contains all n ecessary and/or relevant information about the product. the user agrees that all access and use of the pss is at its own risk. no warranties expressed or implied, including any warranty of merchantability, fitness for a particular purpose or of a ny kind whatsoever are provided
|
