pen-series ? pen6-xxxxe/z4:1lf ? single and dual ou tput ? dip24 - metal case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 pen6-xxxxe/z4:1lf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 4:1 ultra wide input input filter pi type input reflected ripple current1 35 ma pk-pk output specifications voltage accuracy 1% short circuit protection indefinite (automatic recovery) line regulation 0.5% load regulation 0.5% / 1.5% (only 3.3 / 3.3 vout models) ripple and noise (20mhz bandwidth) 60 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 1500 vdc i/o isolation capacity 500 pf, typ. i/o isolation resistance 1000 mohm switching frequency (typical) 266 khz, typ. humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs physical specifications case material nickel coated copper potting material epoxy (ul94v-0 rated) weight ~ 17g, typ. environment specifications operating temperature -40 to +85c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection (10mm distance required) rohs conform soldering 260c, max. (1.5mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de pen-series 4-6 watt 4:1 ultra wide input reg. single and dual output dip24 metal case 1.5 kv dc i/o isolation continuous short circuit prot. rev.09-2009
pen-series ? pen6-xxxxe/z4:1lf ? single and dual ou tput ? dip24 - metal case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single/dual output order # w a t t i n p u t v o l t a g e ( v d c ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output pen6-243r3e4:1lf 4 9 - 36 3.3 1200 78 1000 pen6-2405e4:1lf 5 9 - 36 5 1000 81 680 pen6-247r2e4:1lf 6 9 - 36 7.2 833 80 470 pen6-2412e4:1lf 6 9 - 36 12 500 84 1000 pen6-2415e4:1lf 6 9 - 36 15 400 84 470 pen6-483r3e4:1lf 4 18 - 72 3.3 1200 78 1000 pen6-4805e4:1lf 5 18 - 72 5 1000 82 680 pen6-487r2e4:1lf 6 18 - 72 7.2 833 80 470 pen6-4812e4:1lf 6 18 - 72 12 500 84 1000 pen6-4815e4:1lf 6 18 - 72 15 400 84 100 dual output pen6-243r3z4:1lf 6 9 - 36 3.3 909 74 470 pen6-2405z4:1lf 5 9 - 36 5 500 81 330 pen6-247r2z4:1lf 6 9 - 36 7.2 416 80 220 pen6-2412z4:1lf 6 9 - 36 12 250 84 330 pen6-2415z4:1lf 6 9 - 36 15 200 84 100 pen6-483r3z4:1lf 6 18 - 72 3.3 909 77 330 pen6-4805z4:1lf 5 18 - 72 5 500 81 330 pen6-487r2z4:1lf 6 18 - 72 7.2 416 80 220 pen6-4812z4:1lf 6 18 - 72 12 250 84 100 pen6-4815z4:1lf 6 18 - 72 15 200 84 47 if you need other specifications, please enquire.
pen-series ? pen6-xxxxe/z4:1lf ? single and dual ou tput ? dip24 - metal case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 package / pinning / derating bottom view 1 12 13 24 27.94 (1.10) 2.54 (0.10) pe a k modelcode datecode 31.75 (1.25) 10.16 (0.40) 3.05 (0.12) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) standard drawing for exact pinning please see connection table! specification may change without notice. dip24 C metal case 2.00 (0.08) # single dual 2 - vin - vin 3 - vin - vin 9 omitted common 11 n.c. - vout 14 +vout +vout 16 - vout common 22 +vin +vin 23 +vin +vin others omitted omitted pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh 2 = test by nominal input voltage and constant resi stor load. 3 = it?s recommended to add c1(68mf), c2(33mf), l(1 2mh) in input end to achieve en55022 conducted clas s a. emc specifications radiated emissions en 55022 class a conducted emissions3 en 55022 class a esd iec 61000-4-2 perf. criteria b rs iec 61000-4-3 perf. criteria a eft iec 61000-4-4 perf. criteria b cs iec 61000-4-6 perf. criteria a pfmf iec 61000-4-8 perf. criteria a
|