rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (5) stand juni 2016 rev 01 dc/dc-converter rs1/rd1-s10 1.0w unregulated single output we energize electronics! an acal group company we energize electronics! ? 4 pin sil/ 8pin dil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? low ripple and noise ? efciency up to 83% ? operatng temperature range: -40 ~ +85c ? non conductve black plastc case ? emi complies with en55022 class b output specification voltage accuracy: 3% line regulaton: 1.2% (per 1%vin change) load regulation: 10% ( from 20 to 100%) load output 3.3v model: 20% ripple noise (20mhz bandwidth): 100mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 80khz humidity: 95% rel h reliability calculated mtbf : >1.121mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) pin material sip case: ? 0.5mm alloy42 solder-coated pin material dip case: ? 0.5mm brass solder-coated potng material: epoxy (ul94v-0 rated) weight case- sip: 1.5g weight case-dip: 1.8g dimmension sip: 0.46 x 0.24 x 0.40 dimmension dip: 0.50 x 0.40 x 0.27 absolute maximum ratings (1) input surge voltage (100ms)/ 3.3v models: 6vdc max 5 v models: 7vdc max 12v models: 15vdc max 15v models: 18vdc max 24v models: 28vdc max 48v models: 54vdc max soldering temperature (2) : 260c max. emc specifications radiated-/conducted emissions: en55022 class b esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (5) stand juni 2016 rev 01 rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) 48=48v 20= 2.0 48=48v rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) e?ae? s 20= 2.0 48=48v dc/dc-converter /d- nrete ne tt we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton model selection guide model number input input current output output current
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (5) stand juni 2016 rev 01 dc/dc-converter rs1/rd1-s10 1.0w unregulated single output we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (5) stand juni 2016 rev 01 +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1/rd1-0 3xxs10ax 1210, 2. 2uf/100v 18uh r s 1/rd1-0 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs10ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs10ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1/rd1-0 3xxs10ax 1210, 2. 2uf/100v 18uh r s 1/rd1-0 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs10ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs10ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. +vout +v in dc/dc converter - vin - vout +vout +vin dc /dc converter - vin - vout c3 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. l in current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load emi filter input filter components (c1 , l , c2 , c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 c2 +vout dc/dc converter - vout scope c1 l c2 c3 r s 1/rd1-0 3xxs10ax 1210, 2. 2uf/100v 18uh r s 1/rd1-0 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 2xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-1 5xxs10ax 1210, 2.2uf/100v 18uh r s 1/rd1-2 4xxs10ax 1210, 2.2uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv r s 1/rd1-4 8xxs10ax electrolytic capacitor, 10uf/100v 18uh 1210, 2.2uf/100v 1206, 470pf/2kv the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail t o : info@rsg - electronic.de 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. 6. input filter components are be required to help meet conducted emission class b, which application refer to the emi filter of design & feature configuration. 7. an external filter capacitor is required if the module has to meet iec61000 -4-4 and iec61000 -4- 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100v. dc/dc-converter rs1/rd1-s10 1.0w unregulated single output we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 5 (5) stand juni 2016 rev 01 rs1-xxxxs10a1 rd1-xxxxs10a1 rs1-xxxxs10a1 rd1-xxxxs10a1 rs1-xxxxs10a1 rd1-xxxxs10a1 dc/dc-converter rs1/rd1-s10 1.0w unregulated single output we energize electronics! an acal group company we energize electronics! 4 pin sil 8 pin dil the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
