Part Number Hot Search : 
FFV36AK 20N36 RF2105 RAPH2SG 08100 FCX61903 6EJMS1 60040215
Product Description
Full Text Search
 

To Download MCP651 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  ? 2009-2014 microchip technology inc. ds20002146d-page 1 MCP651/1s/2/3/4/5/9 features: ? gain-bandwidth product: 50 mhz ? slew rate: 30 v/s ? low input offset: 200 v (maximum) ? low input bias current: 6 pa (typical) ? noise: 7.5 nv/ ? hz, at 1 mhz ? ease-of-use: - unity-gain stable - rail-to-rail output - input range incl. negative rail - no phase reversal ? supply voltage range: +2.5v to +5.5v ? high output current: 100 ma ? supply current: 6.0 ma/ch (typical) ? low-power mode: 5 a/ch ? small packages: sot23-5, dfn ? extended temperature range: -40c to +125c typical applications: ? driving a/d converters ? fast low-side current sensing ? power amplifier control loops ? optical detector amplifier ? barcode scanners ? multi-pole active filter ?consumer audio design aids: ? spice macro models ?filterlab ? software ? microchip advanced part selector (maps) ? analog demonstration and evaluation boards - MCP651ev-vos ? application notes description: the microchip technology inc. MCP651/1s/2/3/4/5/9 family of high bandwidth and high slew rate operational amplifiers features low offset. at power-up, these op amps are self-calibrated using mcal. some package options also provide a calibration/chip select pin (cal/cs ) that supports a low-power mode of operation, with offset calibration at the time normal operation is re-started. these amplifiers are optimized for high speed, low noise and distortion, single-supply operation with rail-to-rail output and an input that includes the negative rail. this family is offered in single (MCP651 and MCP651s), single with cal/cs pin (mcp653), dual (mcp652), dual with cal/cs pins (mcp655), quad (mcp654) and quad with cal/cs pins (mcp659). all devices are fully specified from -40c to +125c. typical application circuit 1k ? 100 k ? mcp65x v in v dd /2 v out r l high gain amplifier (g = 101v/v) 0% 5% 10% 15% 20% 25% 30% 35% -100 -80 -60 -40 -20 0 20 40 60 80 100 input offset voltage (v) percentage of occurrences 80 samples t a = +25c v dd = 2.5v and 5.5v calibrated at +25c high gain-bandwidth op amp portfolio model family channels/package gain-bandwidth v os (max.) i q /ch (typ.) mcp621/1s/2/3/4/5/9 1, 2, 4 20 mhz 0.2 mv 2.5 ma mcp631/2/3/4/5/9 1, 2, 4 24 mhz 8.0 mv 2.5 ma MCP651/1s/2/3/4/5/9 1, 2, 4 50 mhz 0.2 mv 6.0 ma mcp660/1/2/3/4/5/9 1, 2, 3, 4 60 mhz 8.0 mv 6.0 ma 50 mhz, 200 v op amps with mcal
MCP651/1s/2/3/4/5/9 ds20002146d-page 2 ? 2009-2014 microchip technology inc. package types MCP651 soic mcp652 soic v in + v in ? v ss v dd v out 1 2 3 4 8 7 6 5 v cal cal/cs nc v ina + v ina ? v ss 1 2 3 4 8 7 6 5 v outa v dd v outb v inb ? v inb + mcp655 msop v ina + v ina ? v ss 1 2 3 4 10 9 8 7 v outa v dd v outb v inb ? v inb + cal a /cs a 5 6 cal b /cs b mcp652 3x3 dfn * mcp655 3x3 dfn * * includes exposed thermal pad (ep); see ta b l e 3 - 1 . v ina + v ina ? v ss v outb v inb ? 1 2 3 4 8 7 6 5 v inb + v dd v outa ep 9 v ss v ina + cal a /cs a v inb ? v inb + 2 3 4 5 9 8 7 6 cal b /cs b v outb v ina ? ep 11 1 10 v dd v outa 2 mcp659 4x4 qfn* v dd v inb + v ina - v ind + v ss v inb - v inc + v outb cal bc /cs bc v outc v inc - v outa cal ad /cs ad v outd v ind - v ina + ep 16 1 15 14 13 3 4 12 11 10 9 5678 17 mcp654 soic, tssop v ina + v ina - v dd 1 2 3 4 14 13 12 11 v outa v outd v ind - v ind + v ss v inb + 5 10 v inc + v inb - 6 9 v outb 7 8 v outc v inc - 1 2 3 4 v out v dd v ss v in + v in ? 5 1 2 3 4 v out v dd v ss v in + v in ? 5 6 cal/ cs MCP651s sot-23-5 mcp653 sot-23-6 MCP651 2x3 tdfn * v in + v in ? v ss v dd v out 1 2 3 4 8 7 6 5 v cal cal/ cs nc ep 9
? 2009-2014 microchip technology inc. ds20002146d-page 3 MCP651/1s/2/3/4/5/9 1.0 electrical characteristics 1.1 absolute maximum ratings ? v dd ?v ss .......................................................................6.5v current at input pins ....................................................2 ma analog inputs (v in + and v in ?) ?? . v ss ? 1.0v to v dd +1.0v all other inputs and outputs .......... v ss ? 0.3v to v dd +0.3v difference input voltage ...................................... |v dd ?v ss | output short circuit current ................................ continuous current at output and supply pins ..........................150 ma storage temperature ...................................-65c to +150c max. junction temperature ........................................ +150c esd protection on all pins (hbm, mm) ????????????????? 1 kv, 200v ? notice: stresses above those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listi ngs of this specification is not implied. exposure to maximum rating conditions for extended periods may affect device reliability. ?? see section 4.2.2 ?input voltage and current limits? . 1.2 specifications table 1-1: dc electrical specifications electrical characteristics: unless otherwise indicated, t a = +25c, v dd = +2.5v to +5.5v, v ss = gnd, v cm = v dd /3, v out ? v dd /2, v l = v dd /2, r l = 1 k ? to v l and cal/cs =v ss (refer to figure 1-2 ). parameters sym. min. typ. max. units conditions input offset input offset voltage v os -200 ? +200 v after calibration ( note 1 ) input offset voltage trim step v ostrm ? 37 200 v input offset voltage drift ? v os / ? t a ?2.5?v/ct a = -40c to +125c power supply rejection ratio psrr 61 76 ? db input current and impedance input bias current i b ?6?pa across temperature i b ? 130 ? pa t a = +85c across temperature i b ? 1700 5,000 pa t a = +125c input offset current i os ?1?pa common mode input impedance z cm ?10 13 ||9 ? ? ||pf differential input impedance z diff ?10 13 ||2 ? ? ||pf common mode common mode input voltage range v cmr v ss ? 0.3 ? v dd ? 1.3 v ( note 2 ) common mode rejection ratio cmrr 65 81 ? db v dd = 2.5v, v cm = -0.3 to 1.2v cmrr 68 84 ? db v dd = 5.5v, v cm = -0.3 to 4.2v open-loop gain dc open-loop gain (large signal) a ol 88 114 ? db v dd = 2.5v, v out = 0.3v to 2.2v a ol 94 123 ? db v dd = 5.5v, v out = 0.3v to 5.2v output maximum output voltage swing v ol , v oh v ss +25 ? v dd ? 25 mv v dd = 2.5v, g = +2, 0.5v input overdrive v ol , v oh v ss +50 ? v dd ? 50 mv v dd = 5.5v, g = +2, 0.5v input overdrive output short-circuit current i sc 50 95 145 ma v dd = 2.5v ( note 3 ) i sc 50 100 150 ma v dd = 5.5v ( note 3 ) note 1: describes the offset (under the specified conditions ) right after power-up, or just after the cal/cs pin is toggled. thus, 1/f noise effects (an apparent wander in v os ; see figure 2-35 ) are not included. 2: see figure 2-6 and figure 2-7 for temperature effects. 3: the i sc specifications are for design gui dance only; they are not tested.
MCP651/1s/2/3/4/5/9 ds20002146d-page 4 ? 2009-2014 microchip technology inc. calibration input calibration input voltage range v calrng v ss +0.1 ? v dd ?1.4 mv v cal pin externally driven internal calibration voltage v cal 0.31v dd 0.33v dd 0.35v dd v cal pin open input impedance z cal ?100||5?k ? ||pf power supply supply voltage v dd 2.5 ? 5.5 v quiescent current per amplifier i q 369mai o = 0 por input threshold, low v prl 1.15 1.40 ? v por input threshold, high v prh ? 1.40 1.65 v table 1-2: ac electrical specifications electrical characteristics: unless otherwise indicated, t a = 25c, v dd = +2.5v to +5.5v, v ss = gnd, v cm = v dd /2, v out ? v dd /2, v l = v dd /2, r l = 1 k ? to v l , c l = 20 pf and cal/cs =v ss (refer to figure 1-2 ). parameters sym. min. typ. max. units conditions ac response gain-bandwidth product gbwp ? 50 ? mhz phase margin pm ? 65 ? g = +1 open-loop output impedance r out ?20? ? ac distortion total harmonic distortion plus noise thd+n ? 0.0012 ? % g = +1, v out = 4v p-p , f = 1 khz, v dd = 5.5v, bw = 80 khz step response rise time, 10% to 90% t r ?6?nsg = +1, v out = 100 mv p-p slew rate sr ? 30 ? v/s g = +1 noise input noise voltage e ni ?17?v p-p f = 0.1 hz to 10 hz input noise voltage density e ni ?7.5?nv/ ? hz f = 1 mhz input noise current density i ni 4?fa/ ? hz f = 1 khz table 1-1: dc electrical specifications (continued) electrical characteristics: unless otherwise indicated, t a = +25c, v dd = +2.5v to +5.5v, v ss = gnd, v cm = v dd /3, v out ? v dd /2, v l = v dd /2, r l = 1 k ? to v l and cal/cs =v ss (refer to figure 1-2 ). parameters sym. min. typ. max. units conditions note 1: describes the offset (under the specified conditions ) right after power-up, or just after the cal/cs pin is toggled. thus, 1/f noise effects (an apparent wander in v os ; see figure 2-35 ) are not included. 2: see figure 2-6 and figure 2-7 for temperature effects. 3: the i sc specifications are for design gui dance only; they are not tested.
? 2009-2014 microchip technology inc. ds20002146d-page 5 MCP651/1s/2/3/4/5/9 table 1-3: digital electrical specifications electrical characteristics: unless otherwise indicated, t a = 25c, v dd = +2.5v to +5.5v, v ss = gnd, v cm = v dd /2, v out ? v dd /2, v l = v dd /2, r l = 1 k ? to v l , c l = 20 pf and cal/cs =v ss (refer to figure 1-1 and figure 1-2 ). parameters sym. min. typ. max. units conditions cal/cs low specifications cal/cs logic threshold, low v il v ss ?0.2v dd v cal/cs input current, low i csl ?0?nacal/cs = 0v cal/cs high specifications cal/cs logic threshold, high v ih 0.8v dd v dd v cal/cs input current, high i csh ? 0.7 ? a cal/cs = v dd gnd current i ss -3.5 -1.8 ? a single, cal/cs = v dd = 2.5v i ss -8 -4 ? a single, cal/cs = v dd = 5.5v i ss -5 -2.5 ? a dual, cal/cs = v dd = 2.5v i ss -10 -5 ? a dual, cal/cs = v dd = 5.5v cal/cs internal pull-down resistor r pd ?5?m ? amplifier output leakage i o(leak) ? 50 ? na cal/cs = v dd por dynamic specifications v dd low to amplifier off time (output goes high z) t poff ? 200 ? ns g = +1 v/v, v l = v ss , v dd = 2.5v to 0v step to v out = 0.1 (2.5v) v dd high to amplifier on time (including calibration) t pon 100 200 300 ms g = +1 v/v, v l = v ss , v dd = 0v to 2.5v step to v out = 0.9 (2.5v) cal/cs dynamic specifications cal/cs input hysteresis v hyst ? 0.25 ? v cal/cs setup time (between cal/cs edges) t csu 1??sg = +1v/v, v l = v ss ( notes 2 , 3 , 4 ) cal/cs = 0.8v dd to v out = 0.1 (v dd /2) cal/cs high to amplifier off time (output goes high z) t coff ? 200 ? ns g = +1 v/v, v l = v ss , cal/cs = 0.8v dd to v out = 0.1 (v dd /2) cal/cs low to amplifier on time (including calibration) t con ?3 4ms g = +1 v/v, v l = v ss , MCP651 and mcp655, cal/cs = 0.2v dd to v out = 0.9 (v dd /2) t con ?6 8ms g = +1 v/v, v l = v ss , mcp659, cal/cs = 0.2v dd to v out = 0.9 (v dd /2) note 1: the mcp652 single, mcp653 single, mcp655 dual and mcp659 quad have their cal/cs inputs internally pulled down to v ss (0v). 2: this time ensures that the internal logic recognizes the edge. however, for the rising edge case, if cal/cs is raised before the calibration is complete, the calibration will be aborted and the part will return to low-power mode. 3: for the mcp655 dual, there is an additional constraint. cal a /cs a and cal b /cs b can be toggled simultaneously (within a time much smaller than t csu ) to make both op amps perform the same function simultaneously. if they are tog- gled independently, then cal a /cs a (cal b /cs b ) cannot be allowed to toggle while op amp b (op amp a) is in calibration mode; allow more than the maximum t con time (4 ms) before the other side is toggled. 4: for the mcp659 quad, there is an additional constraint. cal ad / cs ad and cal bc / cs bc can be toggled simultane- ously (within a time much smaller than t csu ) to make all four op amps perform the same function simultaneously, and the maximum t con time is approximately doubled (8 ms). if they are toggled independently, then cal ad / cs ad (cal bc / cs bc ) cannot be allowed to toggle while op amps b and c (op amps a and d) are in calibration mode; allow more than the maximum t con time (8 ms) before the other side is toggled.
MCP651/1s/2/3/4/5/9 ds20002146d-page 6 ? 2009-2014 microchip technology inc. 1.3 timing diagram figure 1-1: timing diagram. table 1-4: temperature specifications electrical characteristics: unless otherwise indicated, all limits are specified for: v dd = +2.5v to +5.5v, v ss = gnd. parameters sym. min. typ. max. units conditions temperature ranges specified temperature range t a -40 ? +125 c operating temperature range t a -40 ? +125 c ( note 1 ) storage temperature range t a -65 ? +150 c thermal package resistances thermal resistance, 5l-23 sot ? ja ? 220.7 ? c/w thermal resistance, 6l-23 sot ? ja ? 190.5 ? c/w thermal resistance, 8l-23 tdfn ? ja ? 52.5 ? c/w thermal resistance, 8l-33 dfn ? ja ?63?c/w ( note 2 ) thermal resistance, 8l-soic ? ja ? 163 ? c/w thermal resistance, 10l-33 dfn ? ja ?71?c/w ( note 2 ) thermal resistance, 10l-msop ? ja ? 202 ? c/w thermal resistance, 14l-soic ? ja ? 95.3 ? c/w thermal resistance, 14l-tssop ? ja ? 100 ? c/w thermal resistance, 16l-4x4-qfn ? ja ?46?c/w ( note 2 ) note 1: operation must not cause t j to exceed maximum junction tem perature specification (150c). 2: measured on a standard jc51-7, four-layer pr inted circuit board with ground plane and vias. high z v dd v out -3 a (typical) high z i ss i cs -3 a (typical) -6 ma (typical) v prh v prl t pon t poff on 0na(typical) high z -3 a (typical) -6 ma (typical) t coff t con on 0.7 a (typical) 0 na (typical) cal/cs v ih v il t csu note : for the mcp655 dual and the mcp659 quad, there is an additional constraint on toggling the two cal/cs pins close together; see the t con specification in ta b l e 1 - 3 .
? 2009-2014 microchip technology inc. ds20002146d-page 7 MCP651/1s/2/3/4/5/9 1.4 test circuits the circuit used for most dc and ac tests is shown in figure 1-2 . this circuit can independently set v cm and v out ; see equation 1-1 . note that v cm is not the circuit?s common mode voltage ((v p +v m )/2), and that v ost includes v os plus the effects (on the input offset error, v ost ) of temperature, cmrr, psrr and a ol . equation 1-1: figure 1-2: ac and dc test circuit for most specifications. g dm r f r g ? = v cm v p v dd 2 ? + ?? 2 ? = v out v dd 2 ? ?? v p v m ? ?? v ost 1 g dm + ?? ++ = where: g dm = differential mode gain (v/v) v cm = op amp?s common mode input voltage (v) v ost = op amp?s total input offset voltage (mv) v ost v in ? v in + ? = v dd mcp65x r g r f v out v m c b2 c l r l v l c b1 10 k ? 10 k ? r g r f v dd /2 v p 10 k ? 10 k ? 20 pf 1k ? 2.2 f 100 nf v in? v in+ c f 6.8 pf c f 6.8 pf
MCP651/1s/2/3/4/5/9 ds20002146d-page 8 ? 2009-2014 microchip technology inc. 2.0 typical performance curves note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.1 dc signal inputs figure 2-1: input offset voltage. figure 2-2: input offset voltage drift. figure 2-3: input offset voltage repeatability (repeated calibration). figure 2-4: input offset voltage vs. power supply voltage. figure 2-5: input offset voltage vs. output voltage. figure 2-6: low-input common mode voltage headroom vs. ambient temperature. note: the graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. the performance characteristics listed herein are not tested or guaranteed. in some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 0% 5% 10% 15% 20% 25% 30% 35% -100 -80 -60 -40 -20 0 20 40 60 80 100 input offset voltage (v) percentage of occurrences 80 samples t a = +25c v dd = 2.5v and 5.5v calibrated at +25c 0% 2% 4% 6% 8% 10% 12% 14% 16% 18% 20% -10-8-6-4-2 0 2 4 6 810 input offset voltage drift (v/c) percentage of occurrences 80 samples v dd = 2.5v and 5.5v t a = -40c to +125c calibrated at +25c 0% 5% 10% 15% 20% 25% 30% 35% 40% 45% 50% 55% -100 -80 -60 -40 -20 0 20 40 60 80 100 input offset voltage repeatability (v) percentage of occurrences 80 samples t a = +25c v dd = 2.5v and 5.5v calibration changed calibration changed no change (includes noise) -100 0 100 200 300 400 500 600 700 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 power supply voltage (v) input offset voltage (v) +125c +85c +25c -40c representative part calibrated at v dd = 6.5v -50 -40 -30 -20 -10 0 10 20 30 40 50 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 output voltage (v) input offset voltage (v) v dd = 2.5v v dd = 5.5v representative part -0.5 -0.4 -0.3 -0.2 -0.1 0.0 -50 -25 0 25 50 75 100 125 ambient temperature (c) low input common mode headroom (v) v dd = 2.5v 1 lot low (v cmr_l ? v ss ) v dd = 5.5v
? 2009-2014 microchip technology inc. ds20002146d-page 9 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-7: high-input common mode voltage headroom vs. ambient temperature. figure 2-8: input offset voltage vs. common mode voltage with v dd =2.5v. figure 2-9: input offset voltage vs. common mode voltage with v dd =5.5v. figure 2-10: cmrr and psrr vs. ambient temperature. figure 2-11: dc open-loop gain vs. ambient temperature. figure 2-12: input bias and offset currents vs. ambient temperature with v dd =+5.5v. 1.0 1.1 1.2 1.3 1.4 -50 -25 0 25 50 75 100 125 ambient temperature (c) high input common mode headroom (v) v dd = 2.5v v dd = 5.5v 1 lot high (v dd ? v cmr_h ) -1000 -800 -600 -400 -200 0 200 400 600 800 1000 -0.6 -0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 input common mode voltage (v) input offset voltage (v) v dd = 2.5v representative part -40c +25c +85c +125c -1000 -800 -600 -400 -200 0 200 400 600 800 1000 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 input common mode voltage (v) input offset voltage (v) v dd = 5.5v representative part -40c +25c +85c +125c 60 65 70 75 80 85 90 95 100 105 110 -50 -25 0 25 50 75 100 125 ambient temperature (c) cmrr, psrr (db) psrr cmrr, v dd = 5.5v cmrr, v dd = 2.5v 95 100 105 110 115 120 125 130 -50 -25 0 25 50 75 100 125 ambient temperature (c) dc open-loop gain (db) v dd = 5.5v v dd = 2.5v 1 10 100 1,000 10,000 25 45 65 85 105 125 ambient temperature (c) input bias, offset currents (pa) v dd = 5.5v v cm = v cmr_h -i os i b
MCP651/1s/2/3/4/5/9 ds20002146d-page 10 ? 2009-2014 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-13: input bias and offset currents vs. common mode input voltage with t a = +85c. figure 2-14: input bias and offset currents vs. common mode input voltage with t a = +125c. figure 2-15: input bias current vs. input voltage (below v ss ). -60 -40 -20 0 20 40 60 80 100 120 140 160 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 common mode input voltage (v) input bias, offset currents (pa) i b t a = +85c v dd = 5.5v i os -1000 -500 0 500 1000 1500 2000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 common mode input voltage (v) input bias, offset currents (pa) i b t a = +125c v dd = 5.5v i os 1.e-12 1.e-11 1.e-10 1.e-09 1.e-08 1.e-07 1.e-06 1.e-05 1.e-04 1.e-03 -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 input voltage (v) input current magnitude (a) +125c +85c +25c -40c 1m 100 10 1 100n 10n 1n 100p 10p 1p
? 2009-2014 microchip technology inc. ds20002146d-page 11 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.2 other dc voltages and currents figure 2-16: ratio of output voltage headroom to output current. figure 2-17: output voltage headroom vs. ambient temperature. figure 2-18: output short-circuit current vs. power supply voltage. figure 2-19: supply current vs. power supply voltage. figure 2-20: supply current vs. common mode input voltage. figure 2-21: power-on reset voltages vs. ambient temperature. 0 2 4 6 8 10 12 14 1 10 100 output current magnitude (ma) ratio of output headroom to output current (mv/ma) v dd = 2.5v v dd = 5.5v v dd ? v oh i out v ol ? v ss -i out 0 2 4 6 8 10 12 14 -50 -25 0 25 50 75 100 125 ambient temperature (c) output headroom (mv) v dd = 5.5 v v ol ? v ss v dd = 2.5v v dd ? v oh r l = 1 k ? -100 -80 -60 -40 -20 0 20 40 60 80 100 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 power supply voltage (v) output short circuit current (ma) +125c +85c +25c -40c 0 1 2 3 4 5 6 7 8 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 power supply voltage (v) supply current (ma/amplifier) +125c +85c +25c -40c 0 1 2 3 4 5 6 7 8 9 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 common mode input voltage (v) supply current (ma/amplifier) v dd = 2.5 v v dd = 5.5v 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -50 -25 0 25 50 75 100 125 ambient temperature (c) por trip voltages (v) v prl v prh
MCP651/1s/2/3/4/5/9 ds20002146d-page 12 ? 2009-2014 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-22: normalized internal calibration voltage. figure 2-23: v cal input resistance vs. temperature. 0% 5% 10% 15% 20% 25% 30% 33.20% 33.24% 33.28% 33.32% 33.36% 33.40% 33.44% 33.48% 33.52% normalized internal calibration voltage; v cal /v dd percentage of occurrences 144 samples v dd = 2.5v and 5.5v 0 20 40 60 80 100 120 140 -50 -25 0 25 50 75 100 125 ambient temperature (c) internal v cal resistance (k ? )
? 2009-2014 microchip technology inc. ds20002146d-page 13 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.3 frequency response figure 2-24: cmrr and psrr vs. frequency. figure 2-25: open-loop gain vs. frequency. figure 2-26: gain-bandwidth product and phase margin vs. ambient temperature. figure 2-27: gain-bandwidth product and phase margin vs. common mode input voltage. figure 2-28: gain-bandwidth product and phase margin vs. output voltage. figure 2-29: closed-loop output impedance vs. frequency. 0 10 20 30 40 50 60 70 80 90 1.e+2 1.e+3 1.e+4 1.e+5 1.e+6 1.e+7 frequency (hz) cmrr, psrr (db) cmrr psrr+ psrr- 100 1m 10k 10m 100k 1k -20 0 20 40 60 80 100 120 1.e+1 1.e+2 1.e+3 1.e+4 1.e+5 1.e+6 1.e+7 1.e+8 1.e+9 frequency (hz) open-loop gain (db) -210 -180 -150 -120 -90 -60 -30 0 open-loop phase () | a ol | ? a ol 10 1k 100k 10m 1g 100 10k 1m 100m 30 40 50 60 70 80 90 -50 -25 0 25 50 75 100 125 ambient temperature (c) gain bandwidth product (mhz) 10 20 30 40 50 60 70 phase margin () pm gbwp v dd = 5.5v v dd = 2.5v 30 40 50 60 70 80 90 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 common mode input voltage (v) gain bandwidth product (mhz) 10 20 30 40 50 60 70 phase margin () v dd = 5.5v pm v dd = 2.5 v gbwp 0 10 20 30 40 50 60 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 output voltage (v) gain bandwidth product (mhz) 30 40 50 60 70 80 90 phase margin () v dd = 5.5v pm v dd = 2.5 v gbwp 0.1 1 10 100 1000 1.0e+03 1.0e+04 1.0e+05 1.0e+06 1.0e+07 1.0e+08 frequency (hz) 1k 1m 10m 100m open-loop output impedance ( ? ) 10k 100k g = 101 v/v g = 11 v/v g = 1 v/v
MCP651/1s/2/3/4/5/9 ds20002146d-page 14 ? 2009-2014 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-30: gain peaking vs. normalized capacitive load. figure 2-31: channel-to-channel separation vs. frequency. 0 1 2 3 4 5 6 7 8 9 10 1.0e-11 1.0e-10 1.0e-09 normalized capacitive load; c l /g (f) gain peaking (db) 10p 100p 1n 10n g = 1 v/v g = 2 v/v g ? 4 v/v 50 60 70 80 90 100 110 120 130 140 150 1.e+03 1.e+04 1.e+05 1.e+06 1.e+07 frequency (hz) channel-to-channel separation (db) 1k 10k 100k rti v cm = v dd /2 g = +1 v/v r s = 0 ? r s = 1 k ? r s = 10 k ? r s = 100 k ? 1m 10m
? 2009-2014 microchip technology inc. ds20002146d-page 15 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.4 input noise and distortion figure 2-32: input noise voltage density vs. frequency. figure 2-33: input noise voltage density vs. input common mode voltage with f = 100 hz. figure 2-34: input noise voltage density vs. input common mode voltage with f = 1 mhz. figure 2-35: input noise plus offset vs. time with 0.1 hz filter. figure 2-36: thd+n vs. frequency. 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 1.e-1 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 1.e+5 1.e+6 1.e+7 frequency (hz) 0.1 100 10k 1m input noise voltage density (nv/ hz) 1 1k 100k 10m 10 1n 100n 10n 1 10 0 20 40 60 80 100 120 140 160 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 common mode input voltage (v) v dd = 5.5v v dd = 2.5v input noise voltage density (nv/ ? hz) f = 100 hz 0 1 2 3 4 5 6 7 8 9 10 11 12 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 common mode input voltage (v) v dd = 5.5v v dd = 2.5v input noise voltage density (nv/ hz) f = 1 mhz -20 -15 -10 -5 0 5 10 15 20 0 5 10 15 20 25 30 35 40 45 50 time (min) input offset + noise; v os + e ni (t) (v) representative part npbw = 0.1 hz 0.0001 0.001 0.01 0.1 1 1.e+2 1.e+3 1.e+4 1.e+5 frequency (hz) thd + noise (%) v dd = 5.0v 100 1k 10k 100k bw = 22 hz to 80 khz bw = 22 hz to > 500 khz g = 1 v/v g = 11 v/v
MCP651/1s/2/3/4/5/9 ds20002146d-page 16 ? 2009-2014 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.5 time response figure 2-37: non-inverting small signal step response. figure 2-38: non-inverting large signal step response. figure 2-39: inverting small signal step response. figure 2-40: inverting large signal step response. figure 2-41: the MCP651/1s/2/3/4/5/9 family shows no input phase reversal with overdrive. figure 2-42: slew rate vs. ambient temperature. 0 20 40 60 80 100 120 140 160 180 200 time (ns) output voltage (10 mv/div) v dd = 5.5v g = 1 v in v out 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0 100 200 300 400 500 600 700 800 time (ns) output voltage (v) v dd = 5.5v g = 1 v in v out 0 50 100 150 200 250 300 350 400 time (ns) output voltage (10 mv/div) v dd = 5.5v g = -1 r f = 499 ? v in v out 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0 100 200 300 400 500 600 700 800 time (ns) output voltage (v) v dd = 5.5v g = -1 r f = 499 ? v in v out -1 0 1 2 3 4 5 6 7 012345678910 time (ms) input, output voltages (v) v dd = 5.5v g = 2 v out v in 0 5 10 15 20 25 30 35 40 45 50 55 60 -50 -25 0 25 50 75 100 125 ambient temperature (c) slew rate (v/s) falling edge rising edge v dd = 5.5v v dd = 2.5v
? 2009-2014 microchip technology inc. ds20002146d-page 17 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-43: maximum output voltage swing vs. frequency. 0.1 1 10 1.e+05 1.e+06 1.e+07 1.e+08 frequency (hz) maximum output voltage swing (v p-p ) v dd = 5.5v v dd = 2.5v 100k 1m 10m 100m
MCP651/1s/2/3/4/5/9 ds20002146d-page 18 ? 2009-2014 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . 2.6 calibration and chip select response figure 2-44: cal/cs current vs. power supply voltage. figure 2-45: cal/cs voltage, output voltage and supply current (for side a) vs. time with v dd =2.5v. figure 2-46: cal/cs voltage, output voltage and supply current (for side a) vs. time with v dd =5.5v. figure 2-47: cal/cs hysteresis vs. ambient temperature. figure 2-48: cal/cs turn-on time vs. ambient temperature. figure 2-49: cal/cs ?s pull-down resistor (r pd ) vs. ambient temperature. 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 power supply voltage (v) cal/cs current (a) cal/cs = v dd -1 0 1 2 3 4 5 6 7 8 9 012345678910 time (ms) cal/cs, v out (v) -12 -10 -8 -6 -4 -2 0 2 4 6 8 power supply current; i dd (ma) v dd = 2.5v g = 1 v l = 0v op amp turns on cal/cs op amp turns off calibration starts i dd v out -1 0 1 2 3 4 5 6 7 8 9 10 11 012345678910 time (ms) cal/cs, v out (v) -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 power supply current; i dd (ma) v dd = 5.5v g = 1 v l = 0v cal/cs op amp turns off calibration starts i dd v out op amp turns on 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 -50 -25 0 25 50 75 100 125 ambient temperature (c) cal/cs hysteresis (v) v dd = 2.5v v dd = 5.5v 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 -50 -25 0 25 50 75 100 125 ambient temperature (c) cal/cs turn on time (ms) 0 1 2 3 4 5 6 7 8 -50 -25 0 25 50 75 100 125 ambient temperature (c) cal/cs pull-down resistor (m ? ) representative part
? 2009-2014 microchip technology inc. ds20002146d-page 19 MCP651/1s/2/3/4/5/9 note: unless otherwise indicated, t a =+25c, v dd = +2.5v to 5.5v, v ss = gnd, v cm =v dd /3, v out =v dd /2, v l =v dd /2, r l =1k ?? to v l , c l = 20 pf, and cal/cs =v ss . figure 2-50: quiescent current in shutdown vs. power supply voltage. figure 2-51: output leakage current vs. output voltage. -7 -6 -5 -4 -3 -2 -1 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 power supply voltage (v) negative power supply current; i ss (a) cal/cs = v dd +125c +85c +25c -40c 1.e-11 1.e-10 1.e-09 1.e-08 1.e-07 1.e-06 0.00.51.01.52.02.53.03.54.04.55.05.56.0 output voltage (v) output leakage current (a) +25c +125c +85c cal/cs = v dd = 5.5v
MCP651/1s/2/3/4/5/9 ds20002146d-page 20 ? 2009-2014 microchip technology inc. 3.0 pin descriptions descriptions of the pins are listed in table 3-1 . table 3-1: pin function table MCP651 MCP651s mcp652 mcp653 mcp654 mcp655 mcp659 symbol description soic tdfn sot soic dfn sot soic tssop msop dfn qfn 66 1 11 1 1 1 11 16v out , v outa output (op amp a) 22 4 22 4 2 2 22 1v in ?, v ina ? inverting input (op amp a) 33 3 33 3 3 3 33 2v in +, v ina + non-inverting input (op amp a) 44 2 44211114411v ss negative power supply 88 ? ?? 5 ?? 55 ?cal/cs , cal a /cs a calibrate/chip select digital input (op amp a) ?? ? ?? ? ? ? 6 6 ?cal b /cs b calibrate/chip select digital input (op amp b) ? ? ? ? ? ? ? ? ? ? 15 calad/ cs ad calibrate/chip select digital input (op amps a and d) ?? ? ?? ? ? ? ?? 7 cal bc / cs bc calibrate/chip select digital input (op amps b and c) ?? ? 5 5 ? 5 5 7 7 4v inb + non-inverting input (op amp b) ?? ? 6 6 ? 6 6 8 8 5v inb ? inverting input (op amp b) ?? ? 7 7 ? 7 7 9 9 6v outb output (op amp b) ? ? ? ? ? ? 10 10 ? ? 10 v inc + non-inverting input (op amp c) ?? ? ?? ? 9 9 ?? 9v inc - inverting input (op amp c) ?? ? ?? ? 8 8 ?? 8v outc output (op amp c) ? ? ? ? ? ? 12 12 ? ? 12 v ind + non-inverting input (op amp d) ? ? ? ? ? ? 13 13 ? ? 13 v ind - inverting input (op amp d) ? ? ? ? ? ? 14 14 ? ? 14 v outd output (op amp d) 7 7 5 8 8 6 4 4 10 10 3 v dd positive power supply 55 ? ??? ?? ???v cal calibration com- mon mode voltage input 1 1 ? ? ? ? ? ? ? ? ? nc no internal connection ? 9 ? ? 9 ? ? ? ? 11 17 ep exposed thermal pad (ep); must be connected to v ss
? 2009-2014 microchip technology inc. ds20002146d-page 21 MCP651/1s/2/3/4/5/9 3.1 analog outputs the analog output pins (v out ) are low-impedance voltage sources. 3.2 analog inputs the non-inverting and inverting inputs (v in +, v in ?, ?) are high-impedance cmos inputs with low bias currents. 3.3 power supply pins the positive power supply (v dd ) is 2.5v to 5.5v higher than the negative power supply (v ss ). for normal operation, the other pins are between v ss and v dd . typically, these parts are used in a single (positive) supply configuration. in this case, v ss is connected to ground and v dd is connected to the supply. v dd will need bypass capacitors. 3.4 calibration common mode voltage input a low-impedance voltage placed at this input (v cal ) will set the op amps? common mode input voltage during calibration. if this pin is left open, the common mode input voltage during calibration is approximately v dd /3. the internal resistor divider is disconnected from the supplies whenever the part is not in calibra- tion. 3.5 calibrate/chip select digital input this input (cal/cs , ?) is a cmos, schmitt-triggered input that affects the calibration and low-power modes of operation. when this pin goes high, the part is placed into a low-power mode and the output is high z. when this pin goes low, a calibration sequence is started (which corrects v os ). at the end of the cali- bration sequence, the output becomes low-impedance and the part resumes normal operation. an internal por triggers a calibration event when the part is powered on, or when the supply voltage drops too low. thus, the mcp652 parts are calibrated, even though they do not have a cal/cs pin. 3.6 exposed thermal pad (ep) there is an internal connection between the exposed thermal pad (ep) and the v ss pin; they must be connected to the same potential on the printed circuit board (pcb). this pad can be connected to a pcb ground plane to provide a larger heat sink. this improves the package thermal resistance ( ? ja ).
MCP651/1s/2/3/4/5/9 ds20002146d-page 22 ? 2009-2014 microchip technology inc. 4.0 applications the MCP651/1s/2/3/4/5/9 family of self-zeroed op amps is manufactured using microchip?s state-of-the- art cmos process. it is designed for low-cost, low- power and high-precision applications. its low supply voltage, low quiescent current and wide bandwidth makes the MCP651/1s/2/3/4/5/9 ideal for battery- powered applications. 4.1 calibration and chip select these op amps include circuitry for dynamic calibration of the offset voltage (v os ). 4.1.1 mcal calibration circuitry the internal mcal circuitry, when activated, starts a delay timer (to wait for the op amp to settle to its new bias point), then calibrates the input offset voltage (v os ). the mcal circuitry is triggered at power-up (and after some power brown-out events) by the internal por, and by the memory?s parity detector. the power- up time, when the mcal circuitry triggers the calibration sequence, is 200 ms (typical). 4.1.2 cal/cs pin the cal/cs pin gives the user a means to externally demand a low-power mode of operation, then to calibrate v os . using the cal/cs pin makes it possible to correct v os as it drifts over time (1/f noise and aging; see figure 2-35 ) and across temperature. the cal/cs pin performs two functions: it places the op amp(s) in a low-power mode when it is held high, and starts a calibration event (correction of v os ) after a rising edge. while in the low-power mode, the quiescent current is quite small (i ss = -3 a, typical). the output is also in a high z state. during the calibration event, the quiescent current is near, but smaller than, the specified quiescent current (6 ma, typical). the output continues in the high z state, and the inputs are disconnected from the external circuit, to prevent internal signals from affecting circuit operation. the op amp inputs are internally connected to a common mode voltage buffer and feedback resistors. the offset is corrected (using a digital state machine, logic and memory), and the calibration constants are stored in memory. once the calibration event is completed, the amplifier is reconnected to the external circuitry. the turn-on time, when calibration is started with the cal/cs pin, is 3 ms (typical). there is an internal 5 m ? pull-down resistor tied to the cal/cs pin. if the cal/cs pin is left floating, the amplifier operates normally. for the mcp655 dual and the mcp659 quad, there is an additional constraint on toggling the two cal/cs pins close together; see the t con specification in table 1-3 . if the two pins are toggled simultaneously, or if they are toggled separately with an adequate delay between them (greater than t con ), then the cal/cs inputs are accepted as valid. if one of the two pins toggles while the other pin?s calibration routine is in progress, then an invalid input occurs and the result is unpredictable. 4.1.3 internal por this part includes an internal power-on reset (por) to protect the internal calibration memory cells. the por monitors the power supply voltage (v dd ). when the por detects a low v dd event, it places the part into the low-power mode of operation. when the por detects a normal v dd event, it starts a delay counter, then triggers an calibration event. the additional delay gives a total por turn-on time of 200 ms (typical); this is also the power-up time (since the por is triggered at power-up). 4.1.4 parity detector a parity error detector monitors the memory contents for any corruption. in the rare event that a parity error is detected (e.g., corruption from an alpha particle), a por event is automatically triggered. this will cause the input offset voltage to be re-corrected, and the op amp will not return to normal operation for a period of time (the por turn-on time, t pon ). 4.1.5 calibration input pin a v cal pin is available in some options (e.g., the single MCP651) for those applications that need the calibration to occur at an internally driven common mode voltage other than v dd /3. figure 4-1 shows the reference circuit that internally sets the op amp?s common mode reference voltage (v cm_int ) during calibration (the resistors are disconnected from the supplies at other times). the 5k ? resistor provides over-current protection for the buffer. figure 4-1: common-mode reference?s input circuitry. to op amp during v cal buffer 5k ? 300 k ? 150 k ? v ss v dd calibration v cm_int
? 2009-2014 microchip technology inc. ds20002146d-page 23 MCP651/1s/2/3/4/5/9 when the v cal pin is left open, the internal resistor divider generates a v cm_int of approximately v dd /3, which is near the center of the input common mode voltage range. it is recommended that an external capacitor from v cal to ground be added to improve noise immunity. when the v cal pin is driven by an external voltage source, which is within its specified range, the op amp will have its input offset voltage calibrated at that common mode input voltage. make sure that v cal is within its specified range. it is possible to use an external resistor voltage divider to modify v cm_int ; see figure 4-2 . the internal circuitry at the v cal pin looks like 100 k ? tied to v dd /3. the parallel equivalent of r 1 and r 2 should be much smaller than 100 k ? to minimize differences in matching and temperature drift between the internal and external resistors. again, make sure that v cal is within its specified range. figure 4-2: setting v cm with external resistors. for instance, a design goal to set v cm_int =0.1v when v dd = 2.5v could be met with: r 1 =24.3k ? , r 2 =1.00k ? and c 1 = 100 nf. this will keep v cal within its range for any v dd , and should be close enough to 0v for ground-based applications. 4.2 input 4.2.1 phase reversal the input devices are designed to not exhibit phase inversion when the input pins exceed the supply voltages. figure 2-41 shows an input voltage exceeding both supplies with no phase inversion. 4.2.2 input voltage and current limits the esd protection on the inputs can be depicted as shown in figure 4-3 . this structure was chosen to protect the input transistors, and to minimize input bias current (i b ). the input esd diodes clamp the inputs when they try to go more than one diode drop below v ss . they also clamp any voltages that go too far above v dd ; their breakdown voltage is high enough to allow normal operation, and low enough to bypass quick esd events within the specified limits. figure 4-3: simplified analog input esd structures. in order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the currents (and voltages) at the input pins (see section 1.1 ?absolute maximum ratings ?? ). figure 4-4 shows the recommended approach to protecting these inputs. the internal esd diodes prevent the input pins (v in + and v in ?) from going too far below ground, and the resistors r 1 and r 2 limit the possible current drawn out of the input pins. diodes d 1 and d 2 prevent the input pins (v in + and v in ?) from going too far above v dd , and dump any currents onto v dd . when implemented as shown, resistors r 1 and r 2 also limit the current through d 1 and d 2 . figure 4-4: protecting the analog inputs. it is also possible to connect the diodes to the left of the resistor r 1 and r 2 . in this case, the currents through the diodes d 1 and d 2 need to be limited by some other mechanism. the resistors then serve as in-rush current limiters; the dc current into the input pins (v in + and v in ?) should be very small. mcp65x r 1 r 2 v ss v dd v cal c 1 bond pad bond pad bond pad v dd v in + v ss input stage bond pad v in ? v 1 mcp65x r 1 v dd d 1 r 1 > v ss ? (minimum expected v 1 ) 2ma v out r 2 > v ss ? (minimum expected v 2 ) 2ma v 2 r 2 d 2
MCP651/1s/2/3/4/5/9 ds20002146d-page 24 ? 2009-2014 microchip technology inc. a significant amount of current can flow out of the inputs (through the esd diodes) when the common mode voltage (v cm ) is below ground (v ss ); see figure 2-15 . applications that are high-impedance may need to limit the usable voltage range. 4.2.3 normal operation the input stage of the MCP651/1s/2/3/4/5/9 op amps uses a differential pmos input stage. it operates at low common mode input voltage (v cm ), with v cm up to v dd ? 1.3v and down to v ss ? 0.3v. the input offset voltage (v os ) is measured at v cm =v ss ?0.3v and v dd ? 1.3v to ensure proper operation. see figure 2-6 and figure 2-7 for temperature effects. when operating at very low non-inverting gains, the output voltage is limited at the top by the v cm range (< v dd ?1.3v); see figure 4-5 . figure 4-5: unity-gain voltage limitations for linear operation. 4.3 rail-to-rail output 4.3.0.1 maximum output voltage the maximum output voltage (see figure 2-16 and figure 2-17 ) describes the output range for a given load. for instance, the output voltage swings to within 15 mv of the negative rail with a 1 k ? load tied to v dd /2. 4.3.0.2 output current figure 4-6 shows the possible combinations of output voltage (v out ) and output current (i out ). i out is positive when it flows out of the op amp into the external circuit. figure 4-6: output current. v in mcp65x v dd v out v ss v ? in v ? out v dd 1.3v ? ? -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 -120 -100 -80 -60 -40 -20 0 20 40 60 80 100 120 i out (ma) v out (v) r l = 10 ? r l = 100 ? r l = 1 k ? v oh limited v ol limited -i sc limited +i sc limited (v dd = 5.5v)
? 2009-2014 microchip technology inc. ds20002146d-page 25 MCP651/1s/2/3/4/5/9 4.3.0.3 power dissipation since the output short circuit current (i sc ) is specified at 100 ma (typical), these op amps are capable of both delivering and dissipating significant power. two common loads, and their impact on the op amp?s power dissipation, will be discussed. figure 4-7 shows a resistive load (r l ) with a dc output voltage (v out ). v l is r l ?s ground point, v ss is usually ground (0v) and i out is the output current. the input currents are assumed to be negligible. figure 4-7: diagram for resistive load power calculations. the dc currents are: equation 4-1: the dc op amp power is: equation 4-2: the maximum op amp power, for resistive loads at dc, occurs when v out is halfway between v dd and v l or halfway between v ss and v l : equation 4-3: figure 4-7 shows a capacitive load (c l ), which is driven by a sine wave with dc offset. the capacitive load causes the op amp to output higher currents at higher frequencies. because the output rectifies i out , the op amp?s dissipated power increases (even though the capacitor does not dissipate power). figure 4-8: diagram for capacitive load power calculations. the output voltage is assumed to be: equation 4-4: the op amp?s currents are: equation 4-5: the op amp?s instantaneous power, average power and peak power are: equation 4-6: the power dissipated in a package depends on the powers dissipated by each op amp in that package: mcp65x v dd v out r l v l i dd i ss i out v ss i out v out v l ? r l ------------------------- - = i dd i q max 0 i out , ?? + ? i ss i ? q min 0 i out , ?? + ? where: i q = quiescent supply current for one op amp (ma/amplifier) v out = a dc value (v) p oa i dd v dd v out ? ?? i ss v ss v out ? ?? + = max p oa ?? i dd v dd v ss ? ?? = max 2 v dd v l ? v l v ss ? ? ?? 4 r l ----------------------------------------------------------------- - + c l mcp65x v dd v out i dd i ss i out v ss v out v dc v ac ? t ?? sin + = where: v dc = dc offset (v) v ac = peak output swing (v pk ) ? = radian frequency (2 ? f) (rad/s) i out c l dv out dt ---------------- - ? v ac ? c l ? t ?? cos == i dd i q max 0 i out , ?? + ? i ss i ? q min 0 i out , ?? + ? where: i q = quiescent supply current for one op amp (ma/amplifier) p oa i dd v dd v out ? ?? i ss v ss v out ? ?? + = ave p oa ?? v dd v ss ? ?? i q 4v ac fc l ? ----------------------- - + ?? ?? = max p oa ?? v dd v ss ? ?? i q 2v ac fc l + ?? =
MCP651/1s/2/3/4/5/9 ds20002146d-page 26 ? 2009-2014 microchip technology inc. equation 4-7: the maximum ambient to junction temperature rise ( ? t ja ) and junction temperature (t j ) can be calculated using the maximum expected package power (p pkg ), ambient temperature (t a ) and the package thermal resistance ( ? ja ) found in table 1-4 : equation 4-8: the worst-case power de-rating for the op amps in a particular package can be easily calculated: equation 4-9: several techniques are available to reduce ? t ja for a given package: ? reduce ? ja - use another package - improve the pcb layout (ground plane, etc.) - add heat sinks and air flow ? reduce max (p pkg ) - increase r l - decrease c l - limit i out using r iso (see figure 4-9 ) - decrease v dd 4.4 improving stability 4.4.1 capacitive loads driving large capacitive loads can cause stability problems for voltage feedback op amps. as the load capacitance increases, the feedback loop?s phase margin decreases and the closed-loop bandwidth is reduced. this produces gain peaking in the frequency response, with overshoot and ringing in the step response. see figure 2-30 . a unity-gain buffer (g = +1) is the most sensitive to capacitive loads, though all gains show the same general behavior. when driving large capacitive loads with these op amps (e.g., > 20 pf when g = +1), a small series resistor at the output (r iso in figure 4-9 ) improves the feedback loop?s phase margin (stability) by making the output load resistive at higher frequencies. the bandwidth will be generally lower than the bandwidth with no capacitive load. figure 4-9: output resistor, r iso stabilizes large capacitive loads. figure 4-10 gives recommended r iso values for different capacitive loads and gains. the x-axis is the normalized load capacitance (c l /g n ), where g n is the circuit?s noise gain. for non-inverting gains, g n and the signal gain are equal. for inverting gains, g n is 1+|signal gain| (e.g., -1 v/v gives g n =+2v/v). figure 4-10: recommended r iso values for capacitive loads. after selecting r iso for your circuit, double check the resulting frequency response peaking and step response overshoot. modify r iso ?s value until the response is reasonable. bench evaluation and simulations with the MCP651/1s/2/3/4/5/9 spice macro model are helpful. 4.4.2 gain peaking figure 4-11 shows an op amp circuit that represents non-inverting amplifiers (v m is a dc voltage and v p is the input) or inverting amplifiers (v p is a dc voltage and v m is the input). the capacitances c n and c g represent the total capacitance at the input pins; they include the op amp?s common mode input capacitance (c cm ), board parasitic capacitance and any capacitor placed in parallel. p pkg p oa k 1 = n ? = where: n = number of op amps in package (1 or 2) ? t ja p pkg ? ja = t j t a ? t ja + = p pkg t jmax t a ? ? ja -------------------------- ? where: t jmax = absolute maximum junction temperature (c) t a = ambient temperature (c) r iso v out c l mcp65x r g r f r n 1 10 100 1.e-11 1.e-10 1.e-09 1.e-08 normalized capacitance; c l /g n (f) recommended r iso ( ? ) g n = +1 g n ? +2 10p 100p 1n 10n
? 2009-2014 microchip technology inc. ds20002146d-page 27 MCP651/1s/2/3/4/5/9 figure 4-11: amplifier with parasitic capacitance. c g acts in parallel with r g (except for a gain of +1 v/v), which causes an increase in gain at high frequencies. c g also reduces the phase margin of the feedback loop, which becomes less stable. this effect can be reduced by either reducing c g or r f . c n and r n form a low-pass filter that affects the signal at v p . this filter has a single real pole at 1/(2 ? r n c n ). the largest value of r f that should be used depends on noise gain (see g n in section 4.4.1 ?capacitive loads? ) and c g . figure 4-12 shows the maximum recommended r f for several c g values. figure 4-12: maximum recommended r f vs. gain. figure 2-37 and figure 2-38 show the small signal and large signal step responses at g = +1 v/v. the unity- gain buffer usually has r f =0 ? and r g open. figure 2-39 and figure 2-40 show the small signal and large signal step responses at g = -1 v/v. since the noise gain is 2 v/v and c g ? 10 pf, the resistors were chosen to be r f =r g =499 ? and r n = 249 ? . it is also possible to add a capacitor (c f ) in parallel with r f to compensate for the de-stabilizing effect of c g . this makes it possible to use larger values of r f . the conditions for stability are summarized in equation 4- 10 . equation 4-10: 4.5 power supply with this family of operational amplifiers, the power supply pin (v dd for single supply) should have a local bypass capacitor (i.e., 0.01 f to 0.1 f) within 2 mm for good high-frequency performance. surface mount, multilayer ceramic capacitors, or their equivalent, should be used. these op amps require a bulk capacitor (i.e., 2.2 f or larger) within 50 mm to provide large, slow currents. tantalum capacitors, or their equivalent, may be a good choice. this bulk capacitor can be shared with other nearby analog parts as long as crosstalk through the supplies does not prove to be a problem. 4.6 high-speed pcb layout these op amps are fast enough that a little extra care in the pcb (printed circuit board) layout can make a significant difference in performance. good pcb layout techniques will help achieve the performance shown in the specifications and typical performance curves; it will also help minimize emc (electro-magnetic com- patibility) issues. use a solid ground plane. connect the bypass local capacitor(s) to this plane with minimal length traces to cut down inductive and capacitive crosstalk. separate digital from analog, low-speed from high- speed, and low-power from high-power. this will reduce interference. keep sensitive traces short and straight. separate them from interfering components and traces. this is especially important for high-frequency (low rise time) signals. sometimes, it helps to place guard traces next to victim traces. they should be on both sides of the victim trace, and as close as possible. connect guard traces to ground plane at both ends, and in the middle for long traces. use coax cables, or low inductance wiring, to route signal and power to and from the pcb. mutual and self inductance of power wires is often a cause of crosstalk and unusual behavior. v p r f v out mcp65x r n c n v m r g c g 1.e+02 1.e+03 1.e+04 1.e+05 1 10 100 noise gain; g n (v/v) maximum recommended r f ( ? ) g n > +1 v/v 100 10k 100k 1k c g = 10 pf c g = 32 pf c g = 100 pf c g = 320 pf c g = 1 nf f f f gbwp 2g n2 ?? ? , g n1 g n2 < ? we need: g n1 1r f r g ? + = g n2 1c g c f ? + = f f 12 ? r f c f ?? ? = f z f f g n 1 g n 2 ? ?? = given: f f f gbwp 4g n1 ?? ? , g n1 g n2 > ?
MCP651/1s/2/3/4/5/9 ds20002146d-page 28 ? 2009-2014 microchip technology inc. 4.7 typical applications 4.7.1 power driver with high gain figure 4-13 shows a power driver with high gain (1 + r 2 /r 1 ). the MCP651/1s/2/3/4/5/9 op amp?s short- circuit current makes it possible to drive significant loads. the calibrated input offset voltage supports accurate response at high gains. r 3 should be small, and equal to r 1 ||r 2 , in order to minimize the bias current induced offset. figure 4-13: power driver. 4.7.2 optical detector amplifier figure 4-14 shows a transimpedance amplifier, using the MCP651 op amp, in a photo detector circuit. the photo detector is a capacitive current source. the op amp?s input common mode capacitance (5 pf, typical) acts in parallel with c d . r f provides enough gain to produce 10 mv at v out . c f stabilizes the gain and lim- its the transimpedance bandwidth to about 1.1 mhz. r f ?s parasitic capacitance (e.g., 0.2 pf for a 0805 smd) acts in parallel with c f . figure 4-14: transimpedance amplifier for an optical detector. 4.7.3 h-bridge driver figure 4-15 shows the mcp652 dual op amp used as a h-bridge driver. the load could be a speaker or a dc motor. figure 4-15: h-bridge driver. this circuit automatically makes the noise gains (g n ) equal, when the gains are set properly, so that the frequency responses match well (in magnitude and in phase). equation 4-11 shows how to calculate r gt and r gb so that both op amps have the same dc gains; g dm needs to be selected first. equation 4-11: equation 4-12 gives the resulting common mode and differential mode output voltages. equation 4-12: r 1 r 2 mcp65x v in v dd /2 v out r 3 r l photo detector c d c f r f v dd /2 MCP651 30 pf 100 k ? 1.5 pf i d 100 na v out r f ? mcp652 r f v in v ot r f ? mcp652 r gb v ob v dd /2 r gt r l g dm v ot v ob ? v in v dd 2 ? ? -------------------------------- 2 v / v ? ? r gt r f g dm 2 ? ?? 1 ? -------------------------------- - = r gb r f g dm 2 ? ------------------ - = v ot v + ob 2 -------------------------- - v dd 2 ---------- - = v ot v ? ob g dm v in v dd 2 ---------- - ? ?? ?? =
? 2009-2014 microchip technology inc. ds20002146d-page 29 MCP651/1s/2/3/4/5/9 5.0 design aids microchip provides the basic design aids needed for the MCP651/1s/2/3/4/5/9 family of op amps. 5.1 spice macro model the latest spice macro model for the MCP651/1s/2/3/4/5/9 op amps is available on the microchip web site at www.microchip.com . this model is intended to be an initial design tool that works well in the op amp?s linear region of operation over the temperature range. see the model file for information on its capabilities. bench testing is a very important part of any design and cannot be replaced with simulations. also, simulation results using this macro model need to be validated by comparing them to the data sheet specifications and characteristic curves. 5.2 filterlab ? software microchip?s filterlab ? software is an innovative software tool that simplifies analog active filter (using op amps) design. available at no cost from the microchip web site at www.microchip.com/filterlab , the filterlab design tool provides full schematic diagrams of the filter circuit with component values. it also outputs the filter circuit in spice format, which can be used with the macro model to simulate actual filter performance. 5.3 microchip advanced part selector (maps) maps is a software tool that helps efficiently identify microchip devices that fit a particular design require- ment. available at no cost from the microchip web site at www.microchip.com/maps , the maps is an overall selection tool for microchip?s product portfolio that includes analog, memory, mcus and dscs. using this tool, a customer can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. helpful links are also provided for data sheets, purchase and sampling of microchip parts. 5.4 analog demonstration and evaluation boards microchip offers a broad spectrum of analog demonstration and evaluation boards that are designed to help customers achieve faster time to market. for a complete listing of these boards and their corresponding user?s guides and technical information, visit the microchip web site at www.microchip.com/analog tools . some boards that are especially useful are: ? mcp6xxx amplifier evaluation board 1 ? mcp6xxx amplifier evaluation board 2 ? mcp6xxx amplifier evaluation board 3 ? mcp6xxx amplifier evaluation board 4 ? active filter demo board kit ? 8-pin soic/msop/tssop/ dip evaluation board, p/n soic8ev 5.5 application notes the following microchip application notes are available on the microchip web site at www.microchip. com/appnotes and are recommended as supplemental reference resources. ? adn003: ?select the right operational amplifier for your filtering circuits? (ds21821) ? an722: ?operational amplifier topologies and dc specifications? (ds00722) ? an723: ?operational amplifier ac specifications and applications? (ds00723) ? an884: ?driving capacitive loads with op amps? (ds00884) ? an990: ?analog sensor conditioning circuits ? an overview? (ds00990) ? an1177: ?op amp precision design: dc errors? (ds01177) ? an1228: ?op amp precision design: random noise? (ds01228) ? an1332: ?current sensing circuit concepts and fundamentals? ( ds01332) some of these application notes, and others, are listed in the design guide: ? ?signal chain design guide? (ds21825)
MCP651/1s/2/3/4/5/9 ds20002146d-page 30 ? 2009-2014 microchip technology inc. 6.0 packaging information 6.1 package marking information legend: xx...x customer-specific information y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week ?01?) nnn alphanumeric traceability code pb-free jedec ? designator for matte tin (sn) * this package is pb-free. the pb-free jedec designator ( ) can be found on the outer packaging for this package. note : in the event the full microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 3 e 3 e 8-lead dfn (3x3) (mcp652) example: xxxx yyww nnn dabp 1124 256 device code mcp652 dabp note: applies to 8-lead 3x3 dfn xxnn xxnn 6-lead sot-23 (2x3) (mcp653) example: 5-lead sot-23 (2x3) (MCP651s) example: yw25 jd25 8-lead tdfn(2x3) (MCP651) example: aaz 25 124
? 2009-2014 microchip technology inc. ds20002146d-page 31 MCP651/1s/2/3/4/5/9 6.2 package marking information 14-lead tssop (mcp654) example : xxxxxxxx yyww nnn 14-lead soic (mcp654) example: 16-lead qfn (4x4) (mcp659) example: xxxxxxx ywwnnn xxxxxxxxxxx xxxxxxxxxxx yywwnnn 654e/st 1124 256 xxxxxxx 659 124256 e/ml mcp654 e/sl 1124256 3 e 3 e 10-lead msop (mcp655) example: xxxxxx ywwnnn 655 eun 124256 10-lead dfn (3x3) (mcp655) example: xxxx yyww nnn bafc 1124 256 8-lead soic (150 mil) (MCP651, mcp652) xxxxxxxx xxxxyyww nnn example : MCP651 e sn 1124 256 3 e
MCP651/1s/2/3/4/5/9 ds20002146d-page 32 ? 2009-2014 microchip technology inc. n b e e1 d 1 2 3 e e1 a a1 a2 c l l1
? 2009-2014 microchip technology inc. ds20002146d-page 33 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 34 ? 2009-2014 microchip technology inc. 6-lead plastic small outline transistor (chy) [sot-23] notes: 1. dimensions d and e1 do not include mold flash or protrusions. mold flash or protrusions shall not exceed 0.127 mm per side. 2. dimensioning and tolerancing per asme y14.5m. bsc: basic dimension. theoretically exact value shown without tolerances. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging units millimeters dimension limits min nom max number of pins n 6 pitch e 0.95 bsc outside lead pitch e1 1.90 bsc overall height a 0.90 C 1.45 molded package thickness a2 0.89 C 1.30 standoff a1 0.00 C 0.15 overall width e 2.20 C 3.20 molded package width e1 1.30 C 1.80 overall length d 2.70 C 3.10 foot length l 0.10 C 0.60 footprint l1 0.35 C 0.80 foot angle i 0 C 30 lead thickness c 0.08 C 0.26 lead width b 0.20 C 0.51 b e 4 n e1 pin1idby laser mark d 1 2 3 e e1 a a1 a2 c l l1 microchip technology drawing c04-028b
? 2009-2014 microchip technology inc. ds20002146d-page 35 MCP651/1s/2/3/4/5/9 6-lead plastic small outline transistor (chy) [sot-23] note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 36 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 37 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 38 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 39 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 40 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 41 MCP651/1s/2/3/4/5/9
MCP651/1s/2/3/4/5/9 ds20002146d-page 42 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 43 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 44 ? 2009-2014 microchip technology inc.
? 2009-2014 microchip technology inc. ds20002146d-page 45 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 46 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 47 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 48 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging un
? 2009-2014 microchip technology inc. ds20002146d-page 49 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging un
MCP651/1s/2/3/4/5/9 ds20002146d-page 50 ? 2009-2014 microchip technology inc. 10-lead plastic micro small outline package (un) [msop] note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 51 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 52 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 53 MCP651/1s/2/3/4/5/9
MCP651/1s/2/3/4/5/9 ds20002146d-page 54 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 55 MCP651/1s/2/3/4/5/9 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
MCP651/1s/2/3/4/5/9 ds20002146d-page 56 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 57 MCP651/1s/2/3/4/5/9 d e n 2 1 exposed pad d2 e2 2 1 e b k n note 1 a3 a1 a l top view bottom view
MCP651/1s/2/3/4/5/9 ds20002146d-page 58 ? 2009-2014 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging
? 2009-2014 microchip technology inc. ds20002146d-page 59 MCP651/2/3/4/5/9 appendix a: revision history revision d (july 2014) the following is a list of modifications: 1. updated the title of the document. 2. added the high gain-bandwidth op amp portfolio table and updated all sections on page 1. revision c (june 2011) the following is a list of modifications: 3. added the 2x3 tdfn (8l) package option for MCP651, sot-23 (5l) package for MCP651s and sot-23 (6l) package option for mcp653 and the related information throughout the document. revision b (march 2011) the following is a list of modifications: 1. added the mcp654 and mcp659 amplifiers to the product family and the related information throughout the document. 2. added the corresponding soic (14l), tssop (14l) and qfn (16l) package options and related information. revision a (april 2009) ? original release of this document.
MCP651/2/3/4/5/9 ds20002146d-page 60 ? 2009-2014 microchip technology inc. product identification system to order or obtain information, e. g., on pricing or delivery, refer to the factory or the listed sales office . device: MCP651: single op amp MCP651t: single op amp (tape and reel) (soic) MCP651s: single op amp (sot) mcp652: dual op amp mcp652t: dual op amp (tape and reel) (dfn and soic) mcp653t: single op amp (tape and reel) (sot) mcp654: quad op amp mcp654t: quad op amp (tape and reel) (tssop and soic) mcp655: dual op amp mcp655t: dual op amp (tape and reel) (dfn and msop) mcp659: quad op amp mcp659t: quad op amp (tape and reel) (qfn) temperature range: e = -40c to +125c package: ot = plastic small outline, (2x3 sot), 5-lead chy = plastic small outline, (2x3 sot), 6-lead sn = plastic small outline, (3.90 mm), 8-lead mny = plastic dual flat, (2x3 tdfn), 8-lead mf = plastic dual flat, no lead (3x3 dfn), 8-lead, 10-lead un = plastic micro small outline, (msop), 10-lead st = plastic thin shrink small outline, (4.4 mm), 14-lead sl = plastic small outline, narrow, (3.90 mm), 14-lead ml = plastic quad flat, no lead package, (4x4x0.9 mm), 16-lead * y = nickel palladium gold manufacturing designator. only available on the tdfn package. part no. - x /xx package temperature range device examples: a) MCP651st-e/ot: tape and reel, extended temperature, 5ld sot package. b) MCP651t-e/sn: tape and reel, extended temperature, 8ld soic package. c) MCP651t-e/mny: tape and reel, extended temperature, 8ld tdfn package. d) mcp652t-e/mf: tape and reel, extended temperature, 8ld dfn package. e) mcp652t-e/sn: tape and reel, extended temperature, 8ld soic package. f) mcp653t-e/chy: tape and reel, extended temperature, 6ld sot package. g) mcp654t-e/sl: tape and reel, extended temperature, 14ld soic package. h) mcp654t-e/st: tape and reel, extended temperature, 14ld tssop package. i) mcp655t-e/mf: tape and reel, extended temperature, 10ld dfn package. j) mcp655t-e/un: tape and reel, extended temperature, 10ld msop package. k) mcp659t-e/ml: tape and reel, extended temperature, 16ld qfn package.
? 2009-2014 microchip technology inc. ds20002146d-page 61 information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application meets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safety applications is entirely at the buyer?s risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting from such use. no licenses are conveyed, implicitly or otherwise, under any microchip intellectual property rights. trademarks the microchip name and logo, the microchip logo, dspic, flashflex, flexpwr, jukeblox, k ee l oq , k ee l oq logo, kleer, lancheck, medialb, most, most logo, mplab, optolyzer, pic, picstart, pic 32 logo, righttouch, spynic, sst, sst logo, superflash and uni/o are registered trademarks of microchip tec hnology incorporated in the u.s.a. and other countries. the embedded control solutions company and mtouch are registered trademarks of microchip technology incorporated in the u.s.a. analog-for-the-digital age, bodycom, chipkit, chipkit logo, codeguard, dspicdem, dspicdem.net, ecan, in-circuit serial programming, icsp, inter-chip connectivity, kleernet, kleernet logo, miwi, mpasm, mpf, mplab certified logo, mplib, mplink, multitrak, netdetach, omniscient code generation, picdem, picdem.net, pickit, pictail, righttouch logo, real ice, sqi, serial quad i/o, total endurance, tsharc, usbcheck, varisense, viewspan, wiperlock, wireless dna, and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of microchip technology incorporated in the u.s.a. silicon storage technology is a registered trademark of microchip technology inc. in other countries. gestic is a registered trademar ks of microchip technology germany ii gmbh & co. kg, a subsidiary of microchip technology inc., in other countries. all other trademarks mentioned herein are property of their respective companies. ? 2009-2014, microchip technology incorporated, printed in the u.s.a., all rights reserved. isbn: 978-1-63276-393-8 note the following details of the code protection feature on microchip devices: ? microchip products meet the specification cont ained in their particular microchip data sheet. ? microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions. ? there are dishonest and possibly illegal methods used to breach the code protection feature. all of these methods, to our knowledge, require using the microchip produc ts in a manner outside the operating specif ications contained in microchip?s data sheets. most likely, the person doing so is engaged in theft of intellectual property. ? microchip is willing to work with the customer who is concerned about the integrity of their code. ? neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as ?unbreakable.? code protection is constantly evolving. we at microchip are co mmitted to continuously improvin g the code protection features of our products. attempts to break microchip?s code protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the company?s quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microperipherals, nonvolatile memory and analog products. in addition, microchip?s quality system for the design and manufacture of development systems is iso 9001:2000 certified. quality management s ystem certified by dnv == iso/ts 16949 ==
ds20002146d-page 62 ? 2009-2014 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://www.microchip.com/ support web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 austin, tx tel: 512-257-3370 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 cleveland independence, oh tel: 216-447-0464 fax: 216-447-0643 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit novi, mi tel: 248-848-4000 houston, tx tel: 281-894-5983 indianapolis noblesville, in tel: 317-773-8323 fax: 317-773-5453 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 new york, ny tel: 631-435-6000 san jose, ca tel: 408-735-9110 canada - toronto tel: 905-673-0699 fax: 905-673-6509 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2943-5100 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8569-7000 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - chongqing tel: 86-23-8980-9588 fax: 86-23-8980-9500 china - hangzhou tel: 86-571-8792-8115 fax: 86-571-8792-8116 china - hong kong sar tel: 852-2943-5100 fax: 852-2401-3431 china - nanjing tel: 86-25-8473-2460 fax: 86-25-8473-2470 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8864-2200 fax: 86-755-8203-1760 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 china - xiamen tel: 86-592-2388138 fax: 86-592-2388130 china - zhuhai tel: 86-756-3210040 fax: 86-756-3210049 asia/pacific india - bangalore tel: 91-80-3090-4444 fax: 91-80-3090-4123 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-3019-1500 japan - osaka tel: 81-6-6152-7160 fax: 81-6-6152-9310 japan - tokyo tel: 81-3-6880- 3770 fax: 81-3-6880-3771 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - kuala lumpur tel: 60-3-6201-9857 fax: 60-3-6201-9859 malaysia - penang tel: 60-4-227-8870 fax: 60-4-227-4068 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-5778-366 fax: 886-3-5770-955 taiwan - kaohsiung tel: 886-7-213-7830 taiwan - taipei tel: 886-2-2508-8600 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - dusseldorf tel: 49-2129-3766400 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 germany - pforzheim tel: 49-7231-424750 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 italy - venice tel: 39-049-7625286 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 poland - warsaw tel: 48-22-3325737 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 sweden - stockholm tel: 46-8-5090-4654 uk - wokingham tel: 44-118-921-5800 fax: 44-118-921-5820 worldwide sales and service 03/25/14


▲Up To Search▲   

 
Price & Availability of MCP651

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X