? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 page 1 of 8 AD6C941 1 form a 60v / 250m ? mosfet output solid state relay description the AD6C941 is a bi-directional, single-pole, single-throw, normally open multipurpose relay. it is designed to replace electro-mechanical relays in general purpose switching applications. the relay consists of an integrated circuit that drives two rugged drain-to-drain enhancement type dmos transistors - optically coupled to a light emitting diode. the output mos transistors have extremely low on resistance allowing the relay to high continuous load currents of up to 2.2 amps. the AD6C941 comes standard in a miniature 6 pin dip package making it ideal for high-density board applications. schematic diagram agency approvals ul/c-ul: file # e201932 vde: file # 40035191 (en 60747-5-2) applications ? reed relay replacement ? meter reading systems ? data acquisition ? medical equipment ? battery monitoring ? safety systems absolute maximum ratings the values indicated are absolute stress ratings. functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. exposure to absolute maximum ratings may cause permanent damage to the device and may adversely affect reliability. storage temperature ??????????..-55 to +125c operating temperature ?????????-40 to +85c continuous input current ????????????..50ma transient input current ???????.?????..500ma reverse input control voltage ????..???????5v input power dissipation ?????????????40mw output power dissipation ???????????..800mw solder temperature ? wave (10sec)??????.?.260c solder temperature ? ir reflow (10sec)?.????..260c ordering information part number description AD6C941 6 pin dip, (50/tube) AD6C941-h 5kv rms v iso , 6 pin dip, (50/tube) AD6C941-s 6 pin smd, (50/tube) AD6C941-hs 5kv rms , 6 pin smd, (50/tube) AD6C941-str 6 pin smd, tape and reel (1000/reel) AD6C941-hstr 5kv rms , 6 pin smd, tape and reel (1000/reel) note: suffixes listed above are not included in marking on device for part number identification features ? low on resistance (75m ? typ) ? low input control current (1ma typ) ? high maximum continuous load current (2.2 amps) ? high isolation voltage (3.75kv rms , 5kv rms -h option) ? long life / high reliability ? rohs / pb-free / reach compliant 1 2 3 4 5 6 (+) input (-) input do not use -/+ load dc connection +/- load AD6C941
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 2 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay parameter symbol min. typ. max. units test conditions input specifications led forward voltage v f - 1.4 1.8 v i f = 10ma led reverse voltage bv r 5 - - v i r = 10 a input reverse current i r - - 10 ? a v r = 5v turn-on current i f - 1 5 ma v o = 20v, i o = 2.2a, within 20ms turn-off current i foff - 0.5 - ma - output specifications blocking voltage v b 60 - - v i o =1 ? a continuous load current i o - - 2.2 a i f =5ma on resistance r on - 75 250 m ? ? i f =5ma, i o =2.2a leakage current i oleak - 0.05 1 ? a i f =0ma, v o =60v output capacitance c out - 25 - pf i f =0ma, f=1.0mhz offset voltage v offset - - 0.2 mv i f =5ma coupled specifications turn-on time t on - 1 5 ms ? i f =5ma, i o =2.2a turn-off time t off - 0.05 0.5 ms ? i f =0ma, i o =2.2a coupled capacitance c coupled - 3 - pf contact transient ratio - 2,000 7,000 0 v/ ? s dv = 50v offset voltage v offset - - 0.2 mv i f =5ma isolation specifications isolation voltage v iso 3,750 - - v rms rh 50%, t=1min -h option v iso 5,000 - - v rms rh 50%, t=1min input-output resistance r i-o - 10 12 - ?? v i-o = 500v dc electrical characteristics, t a = 25c (unless otherwise specified)
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 3 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay AD6C941 performance & characteristics plots, t a = 25c (unless otherwise specified) i f =5ma, i l =2.2a i f =5ma, i l =2.2a
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 4 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay process step description parameter a preheat start temperature (oc) 150oc b preheat finish temperature (oc) 180oc c preheat time (s) 90 - 120s d melting temperature (oc) 230oc e time above melting temperature (s) 30s f peak temperature, at terminal (oc) 260oc g dwell time at peak temperature (s) 10s h cool-down (oc/s) <6oc/s AD6C941 solder temperature profile recommendations (1) infrared reflow: refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. soldering process should not exceed temperature or time limits expressed herein. su rface temperature of device package should not exceed 250oc: a b c d f e g h (2) wave solder: (3) hand solder: maximum temperature: 260oc (at terminal) maximum time: 10s pre-heating: 100 - 150oc (30 - 90s) single occurrence maximum temperature: 350oc (at tip of soldering iron) maximum time: 3s single occurrence figure 1
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 5 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay AD6C941 package dimensions 6 pin dip package note: all dimensions in inches [?] with millimeters in parenthesis ()
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 6 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay AD6C941 package dimensions 6 pin smd surface mount package (-s) note: all dimensions in inches [?] with millimeters in parenthesis ()
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 7 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay 6 pin smd tape & reel (-str) note: all dimensions in millimeters AD6C941 package dimensions
? 2013 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 8 of 8 AD6C941/h/s/tr rev 1.00 (07/29/2013) 001612 a d6c941 1 form a 60v / 250m ? mosfet output solid state relay note: all weights above are in grams, and include packaging materials where applicable device single unit full tube (50pcs) full pouch (10 tubes) full reel (1000pcs) AD6C941 0.45 48 490 - AD6C941-s 0.44 46 470 - AD6C941-str 0.44 - - 884 solid state optronics (sso) makes no warranties or representations with regards to the completeness and accuracy of this docume nt. sso reserves the right to make changes to product description, specifications at any time without further notices. sso shall not assume any liability arising out of the application or use of any product or circui t described herein. neither c ircuit patent licenses nor indemnity are expressed or implied. except as specified in sso?s standard te rms & conditions, sso disclaims liability fo r consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. disclaimer sso does not authorize use of its devices in life support applicat ions wherein failure or malfunc tion of a device may lead to p ersonal injury or death. users of sso devices in life support applications assume all risks of such use and agree to indemnify sso against any a nd all damages resulting from such use. life s upport devices are defined as devices or syst ems which, (a) are intended for surgical i mplant into the body, or (b) support or sustain life, and (c) whose failure to per form when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support devic e or system, or to affect its safety or effectiveness. life support policy AD6C941 package marking AD6C941 package weights
|
