? semiconductor components industries, llc, 2014 november, 2014 ? rev. 3 1 publication order number: ncv2393/d ncv2393, ts393 micropower dual cmos voltage comparator the ncv2393 and ts393 are micropower cmos dual voltage comparators. they feature extremely low consumption of 6 a typical per comparator and operate over a wide temperature range of t a = ?40 to 125 c. the ncv2393 and ts393 are available in an soic?8 package. features ? extremely low supply current: 6 a typical per channel ? wide supply range: 2.7 to 16 v ? extremely low input bias current: 1 pa typical ? extremely low input offset current: 1 pa typical ? input common mode range includes v ss ? high input impedance: 10 12 ? pin?to?pin compatibility with dual bipolar lm393 ? ncv prefix for automotive and other applications requiring unique site and control change requirements; aec?q100 qualified and ppap capable ? these devices are pb?free, halogen free/bfr free and are rohs compliant soic?8 case 751 pin connections device package shipping ? ordering information marking diagram ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specification s brochure, brd8011/d. http://onsemi.com NCV2393DR2G soic?8 (pb?free) 2500 / tape & ree l a = assembly location l = wafer lot y = year w = work week = pb?free package 1 8 ncv2393 alyw 1 8 1 2 3 45 6 7 8 out 1 in? 1 in+ 1 vss in+ 2 in? 2 out 2 vdd ts393dr2g soic?8 (pb?free) 2500 / tape & ree l
ncv2393, ts393 http://onsemi.com 2 pin description pin name type description 1 out 1 output output of comparator 1. the open?drain output requires an external pull?up resistor. 2 in? 1 input inverting input of comparator 1 3 in+ 1 input non?inverting input of comparator 1 4 vss power negative supply 5 in+ 2 input non?inverting input of comparator 2 6 in? 2 input inverting input of comparator 2 7 out 2 output output of comparator 2. the open?drain output requires an external pull?up resistor. 8 vdd power positive supply absolute maximum ratings (note 1) over operating free?air temperature, unless otherwise stated parameter limit unit supply voltage, v s (v dd ?v ss ) 18 v input and output pins input voltage (note 2) 18 v input differential voltage, v id (note 3) 18 v input current (through esd protection diodes) 50 ma output voltage 18 v output current 20 ma temperature storage temperature ?65 to +150 c junction temperature 150 c esd ratings human body model 1500 v machine model 50 v latch?up ratings latch?up current 100 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. stresses beyond the absolute maximum ratings can lead to reduced reliability and damage. 2. excursions of input voltages may exceed the power supply level. as long as the common mode voltage [v cm = (v in + + v in ?)/2] remains within the specified range, the comparator will provide a stable output state. however, the maximum current through the esd dio des of the input stage must strictly be observed. 3. input dif ferential voltage is the non?inverting input terminal with respect to the inverting input terminal. to prevent damage to the ga tes, each comparator includes back?to?back zener didoes between input terminals. when differential voltage exceeds 6.2 v, the diodes turn on. input resistors of 1 k have been integrated to limit the current in this event. 4. this device series incorporates esd protection and is tested by the following methods: esd human body model tested per aec?q100?002 (jedec standard: jesd22?a114) esd machine model tested per aec?q100?003 (jedec standard: jesd22?a115) latch?up current tested per jedec standard: jesd78. thermal information (note 5) thermal metric symbol value unit junction?to?ambient (note 6) ja 190 c/w junction?to?case top jt 107 c/w 5. short?circuits can cause excessive heating and destructive dissipation. values are typical. 6. multilayer board, 1 oz. copper, 400 mm 2 copper area, both junctions heated equally
ncv2393, ts393 http://onsemi.com 3 operating conditions parameter symbol limit unit supply voltage (v dd ? v ss ) v s +2.7 to +16 v operating free air temperature range t a ?40 to +125 c functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability. electrical characteristics : v s = +3 v ( boldface limits apply over the specified temperature range, t a = ?40 c to +125 c.) parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = mid?supply 1.4 mv input bias current (note 7) i ib v cm = mid?supply 1 pa 600 pa input offset current (note 7) i os v cm = mid?supply 1 pa 300 pa input common mode range v cm v ss v dd ? 1.5 v v ss v dd ? 2 v common mode rejection ratio cmrr v cm = v ss to v cm = v dd ? 1.5 v 70 db output characteristics output voltage low v ol v id = ?1 v, i ol = +6 ma v ss + 300 v ss + 450 mv v ss + 700 mv output current high i oh v id = +1 v, v oh = +3 v 2 40 na 1000 na dynamic performance propagation delay low to high t plh v cm = mid?supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 2.1 s ttl input 0.6 s propagation delay high to low t phl v cm = mid?supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 3.9 s ttl input 0.2 s power supply power supply rejection ratio psrr v s = +3 v to +5 v 70 db quiescent current i dd per channel, no load, output = low 6 15 a 20 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 7. guaranteed by characterization and/or design.
ncv2393, ts393 http://onsemi.com 4 electrical characteristics : v s = +5 v , unless otherwise noted ( boldface limits apply over the specified temperature range, t a = ?40 c to +125 c.) parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = mid?supply v, v s = 5 v to 10 v 1.4 mv input bias current (note 8) i ib v cm = mid?supply 1 pa 600 pa input offset current (note 8) i os v cm = mid?supply 1 pa 300 pa input common mode range v cm v ss v dd ? 1.5 v v ss v dd ? 2 v common mode rejection ratio cmrr v cm = v ss to v cm = v dd ? 1.5 v 71 db output characteristics output voltage low v ol v id = ?1 v, i ol = +6 ma v ss + 260 v ss + 350 mv v ss + 550 mv output current high i oh v id = +1 v, v oh = +5 v 2 40 na 1000 na dynamic performance fall time t fall 50 mv overdrive, f = 10 khz, r pu = 5.1 k , c l = 50 pf 25 ns propagation delay low to high t plh v cm = mid?supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 2.1 s 10 mv overdrive 1.2 s 20 mv overdrive 0.8 s 40 mv overdrive 0.5 s ttl input 0.6 s propagation delay high to low t phl v cm = mid?supply, f = 10 khz, r pu = 5.1 k , c l = 50 pf 5 mv overdrive 5.8 s 10 mv overdrive 3.2 s 20 mv overdrive 1.7 s 40 mv overdrive 1.0 s ttl input 0.3 s power supply power supply rejection ratio psrr vs = +5 v to = +10 v 80 db quiescent current i dd per channel, no load, output = low 6 15 a 20 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 8. guaranteed by characterization and/or design
ncv2393, ts393 http://onsemi.com 5 1.25 1 0.75 0.5 0.25 0 figure 1. i ib and i os vs. temperature 048121620 v ol , low level output voltage (v) i ol , low?level output current (ma) figure 2. v ol vs. i ol v s = 3 v v s = 4 v v s = 5 v v s = 10 v v s = 16 v 450 ?55 ?40 25 70 85 125 v ol , low level output voltage (mv) 400 350 300 250 150 100 50 0 t a , free?air temperature ( c) figure 3. v ol vs. temperature t a = ?55 c t a = ?40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c i dd , supply current ( a) 25 024 101214 v s , supply voltage (v) 68 figure 4. i dd vs. v s 20 15 10 5 0 600 25 45 85 125 current (pa) temperature ( c) 500 400 300 200 100 0 65 105 i ib + i ib ? i os v s = 5 v v cm = mid?rail v s = 5 v i ol = 6 ma 16 output low no loads total i dd of both channels i dd , supply current ( a) 18 v oh , high level output voltage (v) 16 14 12 10 8 6 4 2 0 figure 5. i dd vs. temperature outputs high outputs low v s = 5 v no loads total i dd of both channels ?55 ?40 25 70 85 125 propagation delay (ns) 900 v s , supply voltage (v) 369 303336 800 700 600 500 400 300 27 12 15 18 21 24 t phl t plh figure 6. propagation delay vs. v s overdrive = 50 mv r p = 5.1 k c l = 50 pf t a = 25 c
ncv2393, ts393 http://onsemi.com 6 input amplitude (v) 0.4 propagation delay ( s) ?1 1 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 ?0.05 23 4 5 figure 7. t plh vs. overdrive 40 mv 20 mv 10 mv 5 mv 2 mv v s = 5 v r p = 5.1 k c l = 50 pf t a = 25 c 5 4 3 2 1 0 ?1 ?2 ?3 ?4 ?5 ?6 output amplitude (v) input output 0 input amplitude (v) 0.4 propagation delay ( s) ?3 0 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 ?0.05 36 9 1215 4 3 2 1 0 ?1 ?2 ?3 ?4 ?5 ?6 output amplitude (v) figure 8. t phl vs. overdrive 40 mv 20 mv 10 mv 2 mv v s = 5 v r p = 5.1 k c l = 50 pf t a = 25 c input 5 mv output t fall , fall time (ns) 80 v s , supply voltage (v) 36912 303336 70 60 50 40 30 20 10 0 15 18 21 24 27 figure 9. fall time vs. v s c l = 100 pf c l = 50 pf c l = 15 pf 50 mv overdrive r p = 5.1k to v dd t a = 25 c t a = ?55 c t a = ?40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c offset voltage (mv) input common mode voltage (v) figure 10. v os vs. v cm (v s = 3 v) 1 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 ?1 ?1.5 0.5 0 ?1.0 ?1.0 ?0.5 v dd = 1.5 v v ss = ?1.5 v offset voltage (mv) input common mode voltage (v) figure 11. v os vs. v cm (v s = 5 v) 1 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 ?1 ?1.5 0.5 0 ?1.0 ?2.0 ?0.5 ?2.5 1.0 1.5 t a = ?55 c t a = ?40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c v dd = 2.5 v v ss = ?2.5 v
ncv2393, ts393 http://onsemi.com 7 offset voltage (mv) input common mode voltage (v) figure 12. v os vs. v cm (v s = 10 v) 1 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 ?1 ?1.5 0.5 0 ?1.0 ?1.0 ?0.5 t a = ?55 c t a = ?40 c t a = 25 c t a = 70 c t a = 85 c t a = 125 c v dd = 5 v v ss = ?5 v
ncv2393, ts393 http://onsemi.com 8 package dimensions soic?8 nb case 751?07 issue ak seating plane 1 4 5 8 n j x 45 k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 6. 751?01 thru 751?06 are obsolete. new standard is 751?07. a b s d h c 0.10 (0.004) dim a min max min max inches 4.80 5.00 0.189 0.197 millimeters b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.053 0.069 d 0.33 0.51 0.013 0.020 g 1.27 bsc 0.050 bsc h 0.10 0.25 0.004 0.010 j 0.19 0.25 0.007 0.010 k 0.40 1.27 0.016 0.050 m 0 8 0 8 n 0.25 0.50 0.010 0.020 s 5.80 6.20 0.228 0.244 ?x? ?y? g m y m 0.25 (0.010) ?z? y m 0.25 (0.010) z s x s m 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 mm inches scale 6:1 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other inte llectual property. a listing of scillc?s pr oduct/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typical s? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 ncv2393/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative
|
