www.pairuigroup.com page: 1/3 date: 05/06/2014 dc-dc converter sip-package DBE-1 series, 1watt, 1kvdc, unregulated features: 3 years warranty 1000vdc isolation voltage operating temperature range -40c to +85c compact size model input voltage (vdc) output voltage (vdc) output current (ma) efficiency typ. min. max. dbe1-0310 3.3(2.97~3.63) 3.3 30 300 80% dbe1-0311 5 20 200 80% dbe1-0312 9 11 110 80% dbe1-0313 12 8.3 83 80% dbe1-0314 15 6.8 68 80% dbe1-0315 24 4.2 42 80% dbe1-0510 5(4.5~5.5) 3.3 30 300 80% dbe1-0511 5 20 200 80% dbe1-0512 9 11 110 80% dbe1-0513 12 8.3 83 80% dbe1-0514 15 6.8 68 80% dbe1-0515 24 4.2 42 80% dbe1-1210 12(10.8~13.2) 3.3 30 300 80% dbe1-1211 5 20 200 80% dbe1-1212 9 11 110 80% dbe1-1213 12 8.3 83 80% dbe1-1214 15 6.8 68 80% dbe1-1215 24 4.2 42 80% dbe1-2410 24(21.6~26.4) 3.3 30 300 80% dbe1-2411 5 20 200 80% dbe1-2412 9 11 110 80% dbe1-2413 12 8.3 83 80% dbe1-2414 15 6.8 68 80% dbe1-2415 24 4.2 42 80% notes: other input and output models may available on reques t.
www.pairuigroup.com page: 2/3 date: 05/06/2014 dc-dc converter sip-package DBE-1 series, 1watt, 1kvdc, unregulated electrical line regulation --- 1.2% load regulation 10% ~ 100% full load 15% max. ripple and noise --- 100mvp-p max. isolation voltage --- 1000vdc operating temperature range --- -40c to +85c mtbf --- 3.5x10 6 hrs notes: all the data in this article are under test with ta+25 c, humidity<75%, rated input and rated load mode. mechanical 11.5 (0.453) 10.0 (0.394) 6.0 (0.236 ) 1.94 (0.076) 0.9 (0.035) 4.1 (0.161) connection pin # single 1 gnd 2 +vin 3 -vo 4 +vo note: * unit is mm(inch). temperature profile
www.pairuigroup.com page: 3/3 date: 05/06/2014 dc-dc converter sip-package DBE-1 series, 1watt, 1kvdc, unregulated capacitive loads selection vin (vdc) cin (f) single output voltage (vdc) cout (f) dual output voltage (vdc) cout (f) 3.3/5 4.7 5 10 5 4.7 12 2.2 9 4.7 9 2.2 24 1 12 2.2 12 1 - - 15/24 1 15 0.47 notes recommended test and application circuit in order to ensure the efficiency and dependability of the mo dule, the minimum specified load must be less than 10% of rated load. if the output power is low, we recommend to add an e xternal 10% loading resistor in parallel. fuse: depends on the actual input current; tvs: depends on the actual input voltage; recommended capacitor:c1, c2, c5,about 0.1uf; for c6,c7,p lease check the capacitive load; c3,c4:2kv/1nf.
|
