|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 1 of 8 features: ? mems technology ? direct pin to pin drop-in replacement for industry-standard packages ? ultra-low phase jitter: 0.5 psec (12 khz to 20 mhz) ? lvcmos/hcmos compatible output ? industry-standard package 2.5 x 2.0, 3.2 x 2.5, and 5.0 x 3.2 mm x mm ? pb-free, rohs and reach compliant ? fast delivery times typical applications: ? fibre channel ? server and storage ? gpon, epon ? electrical specifications: frequency range 1.000 mhz to 80.000mhz frequency stability see part number guide inclusive of initial toler ance, operating temperature range, load, and voltage. first year aging 1.5 ppm at + 25oc 2oc 10 years aging 5.0 ppm at + 25oc 2oc operating temperature see part number guide supply voltage (vdd) 10% see part number guide current consumption 31 ma typ./ 33 ma max 29 ma typ./ 31ma max no load condition, f = 20 mhz, vdd = +2.5 v, +2.8 v or +3.3 v no load condition, f = 20 mhz, vdd = +1.8v oe disable current 31 ma max 30 ma max vdd = +2.5 v, +2.8 v or 3.3 v, oe = gnd vdd = +1.8 v, oe = gnd standby current 70 a max 10 a max vdd = +2.5 v, +2.8 v or 3.3 v, st = gnd vdd = +1.8 v, st = gnd waveform output lvcmos/hcmos symmetry 45%/55% 50% of waveform rise / fall time 1.2 nsec typ./ 2.0 nsec max 15 pf load, 10% to 90% of vdd logic ?1? 90% of vdd min logic ?0? 10% of vdd max input voltage high 70% of vdd min pin 1, oe or st input voltage low 30% of vdd max pin 1, oe or st input pull-up impedance 100 k ? typ./ 250 k ? max 2.0 m ? min pin 1, oe logic high or logic low, or st logic high pin 1, st logic low startup time 7 msec typ./ 10 msec max measured from the time vdd reaches its rated minimum values oe enable/disable time 150 nsec max f = 80 mhz, for other frequencies, t_oe = 100 nsec = 3 cycles resume time 6 msec typ./ 10 msec max in standby mode, measured from the time st pin crosses 50% threshold. rms period time 1.5 psec typ./ 2.0 psec max 2.0 psec typ./ 3.0 psec max f = 75 mhz, all vdds rms period time (random) 0.5 psec typ./ 1.0 psec max f = 10 mhz, integration bandwidth = 12 khz to 20 mhz notes: ? all min and max limits are specified over temperature and rate d operating voltage with 15pf ou tput unless otherwise stated. ? typical values are at +25oc and nominal supply voltage. a bsolute maximum limits storage temperature -65oc to +150oc supply voltage (vdd) -0.5 vdc to 4.0 vdc electrostatic discharge 2000 v max solder temperature (follow standard pb free soldering guidelines) 260oc max junction temperature 150oc max
mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 2 of 8 ordering information: part number guide packages input voltage operating temperature output drive strength stability (ppm) select function frequency im810b ? 5.0 x 3.2 im810c ? 3.2 x 2.5 IM810D ? 2.5 x 2.0 1 = +1.8 v 6 = +2.5 v 2 = +2.8 v 7 = +3.0 v 3 = +3.3 v 1 = 0oc to +70oc 2 = -40oc to +85oc 3 = -20oc to +70oc - = default (see tables 2 through 4) e - 10 f = 20 a = 25 b = 50 h = tri-state s = standby - frequency sample part number: im810c-62-fs-10.0000mhz this 10.0000 mhz oscillator in a 3.2 x 2.5 package with stability 20 ppm from -40oc to +85oc using a supply voltage of +2.5 v. the output drive strength (rise and fall time) is 2.00 nsec per table 3 with 30 pf load. with pin 1 function as standby sample part number: im810b-23fah-66.0000mhz this 66.0000 mhz oscillator in a 5.0 x 3.2 package with stability 20 ppm from -40oc to +85oc using a supply voltage of +2.8 v. the output drive strength (rise and fall time) is 1.29 nsec per table 1 with 15 pf load. with pin 1 function as tri-state notes: ? not all options are available at all frequencies and temperatures ranges. ? please consult with sales department for any other parameters or options. ? oscillator specification subj ect to change without notice. phase noise: figure 1: phase noise, 10 mhz, +3.0 v lvcmos output mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 3 of 8 performance plots: figure 2: idd vs frequency figure 3: rms period vs frequency figure 4: duty cycle vs frequency figure 5: rms phase jitter vs frequency figure 6: idd vs temperature, 10 mhz output firgure 7: rise time vs temperature, 75 mhz output mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 4 of 8 test circuit waveform environmental specifications: environmental compliance parameter condition/test method mechanical shock mil-std-883f, method 2002 mechanical vibration mil-std-883f, method 2007 temperature cycle jesd22, method a104 solderability mil-std-883f, method 2003 moisture sensitivity level msl level 1 at +260oc pb free solder reflow profile ts max to t l (ramp-up rate) 3oc / second max preheat temperature min (ts min) temperature typ (ts typ) temperature max (ts max) time (ts) 150oc 175oc 200oc 60 to180 seconds ramp-up tate (t l to tp 3oc / second max time maintained above temperature (t l ) time (t l ) 217oc 60 to 150 seconds peak temperature (tp) 260oc max for seconds time within 5oc to peak temperature (tp) 20 to 40 seconds ramp-down rate 6oc / second max tune 25oc to peak temperature 8 minute max moisture sensitivity level (msl) level 1 units are backward compatible with +240oc reflow processes mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 5 of 8 pin functionally pin description pin symbol functionality pin assignments 1 oe tri-state high or open = specified frequency output low = output is high impedance, only output is disabled. 14 3 2 top view gnd vdd out oe st st standby high or open = specified frequency output. low = output is low. device goes to sleep mode. supply current reduces to standby current. 2 gnd power electrical ground 3 out output oscillator output 4 vdd power power supply voltage notes: 1. in oe or st mode, a pull-up resistor of 10.0 k ? or less is recommended if pin 1 is not externally driven 2. a capacitor of value 0.1 f or higher bet ween pin 4 (vdd) and pin 1 (gnd) is required. timing diagrams: figure 8: startup timing (oe/ mode) figure 9: standby resume timing ( mode only) figure 10: oe enable timing (oe mode only) figure 11: oe disable timing (oe mode only) notes: ? im810 supports gated output which is accurate within rated frequency stability from the first cycle mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 6 of 8 selectable drive strength options rise/fall time (20% to 80%) vs c load tables rise/fall time typ (ns) drive strength (c load ) 5 pf 15 pf 30 pf 45 pf 60 pf l 12.45 17.68 19.48 46.21 57.82 a 6.50 10.27 16.21 23.92 30.76 r 4.38 7.05 11.61 16.17 20.83 b 3.27 5.30 8.89 12.18 15.75 s 2.62 4.25 7.20 9.81 12.65 d 2.19 3.52 6.00 8.31 10.59 t 1.76 3.01 5.14 7.10 9.15 e 1.59 2.59 4.49 6.25 7.98 u 1.49 2.28 3.96 5.55 7.15 f 1.22 2.10 3.57 5.00 6.46 w 1.07 1.88 3.23 4.50 5.87 g 1.01 1.64 2.96 4.12 5.40 x 0.96 1.50 2.74 3.80 4.98 k 0.92 1.41 2.56 3.52 4.64 y 0.88 1.34 2.39 3.25 4.32 q 0.86 1.29 2.24 3.04 4.06 - = default 0.82 1.24 2.07 2.89 3.82 m 0.77 1.20 1.94 2.72 3.61 n 0.66 1.15 1.84 2.58 3.41 p 0.51 1.09 1.76 2.45 3.24 rise/fall time typ (ns) drive strength (c load ) 5 pf 15 pf 30 pf 45 pf 60 pf l 8.68 13.59 18.36 32.70 42.06 a 4.42 7.18 11.93 16.60 21.38 r 2.93 4.78 8.15 11.19 14.59 b 2.21 3.57 6.19 8.55 11.04 s 1.67 2.87 4.94 6.85 8.80 d 1.50 2.33 4.11 5.68 7.33 t 1.06 2.04 3.50 4.84 6.26 e 0.98 1.69 3.03 4.20 5.51 u 0.93 1.48 2.69 3.73 4.92 f 0.90 1.37 2.44 3.34 4.42 w 0.87 1.29 2.21 3.04 4.02 - = default 0.67 1.20 2.00 2.79 3.69 x 0.44 1.10 1.86 2.56 3.43 k 0.38 0.99 1.76 2.37 3.18 y 0.36 0.83 1.66 2.20 2.98 q 0.34 0.71 1.58 2.07 2.80 z 0.33 0.65 1.51 1.95 2.65 m 0.32 0.62 1.44 1.85 2.50 n 0.31 0.59 1.37 1.77 2.39 p 0.30 0.57 1.29 1.70 2.28 table 1: vdd = +1.8 v rise /fall time for specific c load table 2: vdd = +2.5 v rise/fall time for specific c load rise/fall time typ (ns) drive strength (c load ) 5 pf 15 pf 30 pf 45 pf 60 pf l 7.93 12.69 17.94 30.10 38.89 a 4.06 6.66 11.04 15.31 19.80 r 2.68 4.40 7.53 10.29 13.37 b 2.00 3.25 5.66 7.84 10.11 s 1.59 2.57 4.54 6.27 8.07 d 1.19 2.14 3.76 5.21 6.72 t 1.00 1.79 3.20 4.43 5.77 e 0.94 1.51 2.78 3.84 5.06 u 0.90 1.38 2.48 3.40 4.50 f 0.87 1.29 2.21 3.03 4.05 w 0.62 1.19 1.99 2.76 3.68 - = default 0.41 1.08 1.84 2.52 3.36 x 0.37 0.96 1.72 2.33 3.15 k 0.35 0.78 1.63 2.15 2.92 y 0.33 0.67 1.54 2.00 2.75 q 0.32 0.63 1.46 1.89 2.57 z 0.31 0.60 1.39 1.80 2.43 m 0.30 0.57 1.31 1.72 2.30 n 0.30 0.56 1.22 1.63 2.22 p 0.29 0.54 1.13 1.55 2.13 rise/fall time typ (ns) drive strength (c load ) 5 pf 15 pf 30 pf 45 pf 60 pf l 7.18 11.59 17.24 27.57 35.57 a 3.61 6.02 10.19 13.98 18.10 r 2.31 3.95 6.88 9.42 12.24 b 1.65 2.92 5.12 7.10 9.17 s 1.43 2.26 4.09 5.66 7.34 d 1.01 1.91 3.38 4.69 6.14 t 0.94 1.51 2.86 3.97 5.25 e 0.90 1.36 2.50 3.46 4.58 u 0.86 1.25 2.21 3.03 4.07 - = default 0.48 1.15 1.95 2.72 3.65 w 0.38 1.04 1.77 2.47 3.31 g 0.36 0.87 1.66 2.23 3.03 x 0.34 0.70 1.56 2.04 2.80 k 0.33 0.63 1.48 1.89 2.61 y 0.32 0.60 1.40 1.79 2.43 q 0.32 0.58 1.31 1.69 2.28 z 0.30 0.56 1.22 1.62 2.17 m 0.30 0.55 1.12 1.54 2.07 n 0.30 0.54 1.02 1.47 1.97 p 0.29 0.52 0.95 1.41 1.90 table 3: vdd = +2.8 v rise /fall time for specific c load table 4: vdd= +3.0 v rise/fall time for specific c load mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 7 of 8 mechanical details: package dimensions and suggest land pattern marking 5.00 0.05 3.20 0.05 0.80 2.39 1.15 1.1 0.80 max 2.54 2.20 1.5 1.6 opton b: 5.00 x 3.20 package 3 4 2 1 bottom view 3 marking 3.20 0.05 2.500.05 0.90 2.1 0.9 0.7 0.80 max bottom view 2.20 1.90 1.4 1.2 option c: 3.20 x 2.50 package 4 2 1 marking 2.70 0.05 2.40 0.05 1.10 1.00 0.75 0.5 0.80 max bottom view 1.90 1.50 1.1 1.0 option d: 2.70 x 2.40 package (100% compatible with 2.50 x 2.00 ) 21 3 4 suggested land pattern suggested land pattern suggested land pattern marking line 1 = xxxxx (lot code) dot to denote pin 1 location package information leadframe: c194 plating: nipdau mems oscillator, ultra performance, lvcmos/hcm os compatible, 1.00 mhz to 80.00 mhz im810 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev 01/30/16_a page 8 of 8 tape and reel dimensions direction of feed ref: eia-481-e q3 q4 q2 q1 width tape pitch reel dia part number size pitch tape width pin orient. reel dia. count im810b 5.0 x 3.2 8.0 0.1 12.3 max q1 180 1000 330 3000 im810c 3.2 x 2.5 4.0 0.1 8.3 max q1 180 3000 IM810D 2.5 x 2.0 4.0 0.1 8.3 max q1 180 3000 notes: ? all dimensions are in mm. ? do not scale drawings. proprietary and confidential this document contains proprietary information, and s uch information may not be disclosed to others for any purpose nor used for manufacturing purposes wi thout written permission from ilsi america. |
Price & Availability of IM810D |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |