SKM450GB12T4 ? by semikron rev. 1.0 C 01.03.2016 1 semitrans ? 3 gb fast igbt4 modulesSKM450GB12T4 features igbt4 = 4. generation fast trench igbt (infineon) cal4 = soft switching 4. generation cal-diode insulated copper baseplate using dbc technology (direct bonded copper) increased power cycling capability with integrated gate resistor for higher switching frequenzies up to 20khz ul recognized, file no. e63532 typical applications* ac inverter drives ups electronic welders at fsw up to 20 khz remarks case temperature limited to t c = 125c max. recommended t op = -40 ... +150c product reliability results valid for t j = 150c absolute maximum ratings symbol conditions values unit igbtv ces t j =25c 1200 v i c t j = 175 c t c =25c 699 a t c =80c 538 a i cnom 450 a i crm i crm = 3xi cnom 1350 a v ges -20 ... 20 v t psc v cc = 800 v v ge 15 v v ces 1200 v t j =150c 10 s t j -40 ... 175 c inverse diode i f t j = 175 c t c =25c 461 a t c =80c 345 a i fnom 400 a i frm i frm = 3xi fnom 1200 a i fsm t p = 10 ms, sin 180, t j =25c 1980 a t j -40 ... 175 c module i t(rms) 500 a t stg -40 ... 125 c v isol ac sinus 50 hz, t = 1 min 4000 v characteristics symbol conditions min. typ. max. unit igbtv ce(sat) i c =450a v ge =15v chiplevel t j =25c 1.84 2.07 v t j =150c 2.23 2.42 v v ce0 chiplevel t j =25c 0.80 0.90 v t j =150c 0.70 0.80 v r ce v ge =15v chiplevel t j =25c 2.3 2.6 m t j =150c 3.4 3.6 m v ge(th) v ge =v ce , i c = 16.4 ma 5.3 5.8 6.3 v i ces v ge =0v v ce = 1200 v t j =25c 5m a t j =150c -m a c ies v ce =25v v ge =0v f=1mhz 27.2 nf c oes f=1mhz 1.76 nf c res f=1mhz 1.50 nf q g v ge = - 8 v...+ 15 v 2500 nc r gint t j =25c 1.9 t d(on) v cc = 600 v i c =450a v ge = +15/-15 v r g on =1 r g off =1 di/dt on = 8300 a/s di/dt off =3800a/s du/dt = 3700 v/s t j =150c 224 ns t r t j =150c 59 ns e on t j =150c 32 mj t d(off) t j =150c 460 ns t f t j =150c 91 ns e off t j =150c 49 mj r th(j-c) per igbt 0.062 k/w
SKM450GB12T4 2 rev. 1.0 C 01.03.2016 ? by semikron characteristics symbol conditions min. typ. max. unit inverse diode v f = v ec i f = 450 a v ge =0v chiplevel t j =25c 2.31 2.65 v t j =150c 2.31 2.64 v v f0 chiplevel t j =25c 1.30 1.50 v t j =150c 0.90 1.10 v r f chiplevel t j =25c 2.3 2.6 m t j =150c 3.1 3.4 m i rrm i f = 450 a di/dt off =8000a/s v ge =15v v cc = 600 v t j =150c 440 a q rr t j =150c 65 c e rr t j =150c 28 mj r th(j-c) per diode 0.13 k/w module l ce 15 nh r cc'+ee' measured per switch t c =25c 0.55 m t c =125c 0.85 m r th(c-s) per module 0.02 0.038 k/w m s to heat sink m6 3 5 nm m t to terminals m6 2.5 5 nm nm w 325 g semitrans ? 3 gb fast igbt4 modulesSKM450GB12T4 features igbt4 = 4. generation fast trench igbt (infineon) cal4 = soft switching 4. generation cal-diode insulated copper baseplate using dbc technology (direct bonded copper) increased power cycling capability with integrated gate resistor for higher switching frequenzies up to 20khz ul recognized, file no. e63532 typical applications* ac inverter drives ups electronic welders at fsw up to 20 khz remarks case temperature limited to t c = 125c max. recommended t op = -40 ... +150c product reliability results valid for t j = 150c
SKM450GB12T4 ? by semikron rev. 1.0 C 01.03.2016 3 fig. 1: typ. output characteristic, inclusive r cc'+ ee' fig. 2: rated current vs. temperature i c = f (t c ) fig. 3: typ. turn-on /-off energy = f (i c ) fig. 4: typ. turn-on /-off energy = f (r g ) fig. 5: typ. transfer characteristic fig. 6: typ. gate charge characteristic
SKM450GB12T4 4 rev. 1.0 C 01.03.2016 ? by semikron fig. 7: typ. switching times vs. i c fig. 8: typ. switching ti mes vs. gate resistor r g fig. 9: transient thermal impedance fig. 10: typ. cal diode forward charact., incl. r cc'+ ee' fig. 11: cal diode peak reverse recovery current fig. 12: typ. cal diode peak reverse recovery charge
SKM450GB12T4 ? by semikron rev. 1.0 C 01.03.2016 5 semitrans 3 gb
SKM450GB12T4 6 rev. 1.0 C 01.03.2016 ? by semikron this is an electrostatic discharge sensitive device (esds), international standard iec 60747-1, chapter ix. *important information and warnings the specifications of semikron products may not be consid ered as guarantee or assurance of product characteristics ("beschaffenheitsgarantie"). the specifications of semikron products describe only the usual characteristics of products to be expected in typical applications, which may still vary depe nding on the specific application. therefore, products must be tested for the re spective application in advance. application adjustments may be necessary. the user of semikron products is responsible for the safety o f their applications embedding semikron pr oducts and must take adequate safety measures to prevent the applications from causing a phys ical injury, fire or other problem if any of semi kron products become faulty. the user is responsible to make su re that the applicat ion design is compliant with all applicable laws, regulati ons, norms and standards. exce pt as otherwise explicitly approved by semikron in a written document signed by authorized representatives of semikron, semikr on products may not be used in any applications where a failur e of the product or any consequences of the use thereof can reasonably be expected to result in person al injury. no representation o r warranty is given and no liability is assumed with respect to the accuracy, completeness and/or use of any information herein, including wi thout limitation, warranties of non-infringement of intellectual property rights of any third party. semikron does not assume any liability arisi ng out of the applications or use of any product; neither does it convey an y license under its patent rights, copyrights, trade secrets or ot her intellectual property rights, nor the rights of others. semikron makes no re presentation or warranty of non- infringement or alleged non-infr ingement of intellectual property rights of any third party which may arise fr om applications. due to technica l requirements our products m ay contain dangerous substances. for information on the types in question pl ease contact the nearest semikron sales office. this document supersedes and replaces all information previously supplied and ma y be superseded by updates. semikron reserves the right to ma ke changes.
|
