ps2913-1 nec's single tr. output, high collector-emitter voltage, 4-pin ultra small flat lead optocoupler features ? ultra small flat lead package: 4.6 (l) x 2.5 (w) x 2.1 (h) mm ? isolation distance: 0.4 mm min ? high collector to emitter voltage: v ceo = 120 v ? high isolation voltage bv = 2500 vr.m.s. ? available in tape and reel: PS2913-1-F3, f4: 3500 pcs/reel p art number ps2913-1 symbols parameters units min typ max v f forward voltage, i f = 1 ma v 0.9 1.1 1.3 i r reverse current, v r = 5 v a5 c t t erminal capacitance, v = 0, f = 1.0 mhz pf 15 i ceo collector to emitter dark current, i f = 1 ma, v ce = 120 v na 100 ctr current transfer ratio (i c /i f ), i f = 1 ma, v ce = 5 v % 50 100 200 v ce(sat) collector saturation voltage, i f = 1 ma, i c = 0.2 ma v 0.13 0.3 r i-o isolation resistance, v i-o = 1.0 kv dc ? 10 11 c i-o isolation capacitance, v = 0 v, f = 1.0 mhz pf 0.4 tr rise time 1 v cc = 5 v, i c = 2 ma, r l = 100 ? s10 tf fall time 1 s10 t on on time 1 v cc = 5 v, i f = 1 ma, r l = 5 k ? s80 t s storage time 1 s5 t f off time 1 s50 electrical characteristics (t a = 25 c) t ransistor diode coupled california eastern laboratories note: 1. test circuit for switching time description nec's ps2913-1 is an optically coupled isolator containing a gaas light emitting diode and an npn silicon phototransistor is one package for high density mounting applications. this device is housed in an ultra small flat-lead package which realizes a reduction in mounting area of about 30% compared with the ps28xx series. applications ? hybrid ic ? power supply pulse input v cc v out r l = 100 ? or 5 k ? pw = 100 ? duty cycle = 1/10 if 50 ? in monitor
outline dimensions (units in mm) to p view marking n 13 111 ?last number of type no: 13 ?an initial of "nec" ?assembly lot no. 1 pin mark (nicked corner) 1 11 week assembled year assembled ps2913-1 . symbols parameters units ratings diode i f forward current (dc) ma 50 ? i f / c forward current derating ma/ c 0.5 i f (peak) peak forward current 2 a 0.5 p d power dissipation mw 60 v r reverse voltage v 6 t ransistor v ceo collector to emitter voltage v 120 v eco emitter to collector voltage v 6 i c collector current ma 30 ? p c / ? c power dissipation derating mw/ ? c 1.2 p c power dissipation mw 120 coupled v iso isolation voltage 3 v r .m.s. 2500 p t t otal power dissipation mw 160 t a operating ambient temp. c -55 to +100 t stg storage temperature c -55 to +150 absolute maximum ratings 1 (t a = 25 c) notes: 1. operation in excess of any one of these parameters may result in permanent damage. 2. pw = 100 s, duty cycle = 1%. 3. ac voltage for 1 minute at t a = 25 c, rh = 60% between input and output. n 2.50.3 4 3 1 2 4.60.2 4.1 min 5.00.2 0.15 +0.1 -0.05 0.20.1 2.1 max 0.40.1 1.27 0.8 0.6 1.27 (0.35) 4.14 4.7 5.7 24-r0.1 ( ): reference value recommended mount pad dimensions (units in mm) remark: this drawing is considered to meet air and outer creepage distance 4.0 minimum. all dimensions in this figure must be evaluated before use. 4 3 1 2 1. anode 2. cathode 3. emitter 4. collector optocoupler construction p arameter units (min) air distance 4 mm creepage distance 4 mm isolation distance 0.4 mm p art number packing style PS2913-1-F3 embossed tape 3500 pcs/reel ps2913-1-f4 ordering information cautions regarding noise: be aware that when voltage is applied suddenly between the optocoupler's input and outout or between collector-emitters at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings.
typical characteristics (t a = 25 c, unless otherwise specified) ctr = 100% 2 ma 1 ma 10 1 0.1 0.0 0.2 0.4 0.6 0.8 1.0 5 ma i f = 0.5 ma 80 60 40 20 0 25 50 75 100 0.5 ma/ c 02550751 00 120 120 140 100 80 60 40 20 100 10 1 0.1 0.01 0.0 0.5 1.0 1.5 2.0 t a = +100 c +60 c +25 c 0 c -25 c -50 c ctr = 200 % 12 10 8 6 4 2 0246810 i f = 5 ma 2 ma 1 ma 0.5 ma 50000 10000 5000 1000 500 100 50 10 5 1 0.5 0.1 -60 -40 -20 0 20 40 60 80 100 v ce = 40 v 24 v 10 v maximum forward current, i f (ma) ambient temperature, t a ( c) ambient temperature, t a ( c) t ransistor power dissipation, p c (mw) forward voltage, v f (v) forward current, i f (ma) collector current, i c (v) collector to emitter voltage, v ce (v) collectorsaturation voltage, v ce(sat) (v) collector current, i c (ma) ambient temperature, t a ( c) collector to emitter dark current, i ceo (na) maximum forward current vs. ambient temperature transistor power dissipation vs. ambient temperature forward currentvs. forward voltage collector currentvs. collector to emitter voltage collector to emitter dark current vs. ambient temperature collector current vs. collector saturation voltage ps2913-1
typical characteristics (t a = 25 c, unless otherwise specified) normalized to 1.0 at t a = 25c, i f = 1 ma, v ce = 5 v 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -50 -25 0 25 50 75 100 i f = 1 ma, v cc = 5 v, ctr = 200 % 10000 1000 100 10 1 1k 10k 100k 1000k t off t on t s r l = 1 k ? 510 ? 300 ? 100 ? 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.5 1 5 10 50 100 500 1.2 1.0 0.8 0.6 0.4 0.2 0.0 10 10 2 10 3 10 4 10 5 10 6 i f = 5 ma, t a = 25 c i f = 1 ma, t a = 25 c i f = 20 ma, t a = 60 c i f = 20 ma, t a = 25 c t ime (hr) ctr (relative value) load resistance, r l ( ? ) switching time, t ( s) normalized gain, g v frequency, f (khz) forward current, i f (ma) current transfer ratio, ctr (%) ambient temperature, t a ( c) normalized current transfer ratio, ctr normalized current transfer ratio vs. ambient temperature current transfer ratio vs. forward current switching time vs. load resistance frequency response long term ctr degradation ps2913-1 300 250 200 150 100 50 0 0.1 1 10 100 v ce = 5 v, n = 3 sample a b c remark: the graphs indicate nominal characteristics.
t aping specifications (units in mm) 2.0 0.5 4.0 0.1 1.55 0.05 4.0 0.1 2.9 0.1 2.9 max 2.40.1 1.75 0.1 5.3 0.1 12.0 0.2 5.3 0.1 1.55 +0.1 -0 2.0 0.5 13.0 0.2 21.0 0.8 r1.0 100 1.0 3302.0 2.00.5 11.9 to 15.4 outer edge of flange 13.51.0 ps2913-1 packing: 3500 pcs/reel t ape outline and dimensions t ape direction reel outline and dimensions n n n n n n n n PS2913-1-F3 PS2913-1-F3
recommended soldering conditions (1) infrared reflow soldering ? peak reflow temperature 260 ? c or below (package surface temperature) ? time of peak reflow temperature 10 seconds or less ? time of temperature higher than 220 ? c 60 seconds or less ? time to preheat temperature from 120 to 180 c 120 30 s ? number of reflows three ? flux rosin flux containing small amount of chlorine (the flux with a maximum chlorine content of 0.2 wt % is recommended). (2) wave soldering ? temperature 260 ? c or below (molten solder temperature) ? time 10 seconds or less ? preheating conditions 120 c or below (package surface temperature) ? number of times one (allowed to be dipped in solder including plastic mold portion.) ? flux rosin flux containing small amount of chlorine (the flux with a maximum chlorine content of 0.2 wt % is recommended). (3) cautions ? fluxes avoid removing the residual flux with chlorine-based cleaning solvent after a reflow process. usage cautions 1. protect against static electricity when handling. 2. avoid storage at a high temperature ad high humidity. recommended temperature profile of infrared reflow ps2913-1 time (s) pa c kage surface temperature t (?c) 180 ?c 120 30 s (preheating) (heating) to 10 s to 60 s 260 ?c (peak temperature) 220 ?c 120?c a business partner of nec com p ound semiconductor devices, ltd . 10/14/2003 life support applications these nec products are not intended for use in life support devices, appliances, or systems where the malfunction of these prod ucts can reasonably be expected to result in personal injury. the customers of cel using or selling these products for use in such applications do so at their own risk and agree to fully indemnify cel for all damages resulting from such improper use or sale.
|
