View SDP117HVUHD_9113264.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

revisions ltr description date (yr-mo-da) approved a drawing updated to reflect current requirements. ? gt 04-04-29 r. monnin b added footnote 1 to table ii, under gr oup c end-point electricals. updated drawing paragraphs. -sld 11-05-20 charles f. saffle rev sheet rev sheet rev status rev b b b b b b b b b b b b b of sheets sheet 1 2 3 4 5 6 7 8 9 10 11 12 13 pmic n/a prepared by gary zahn dla land and maritime columbus, ohio 43218-3990 http://www.dscc.dla.mil standard microcircuit drawing checked by michael c. jones this drawing is available for use by all departments approved by ray monnin microcircuit, linear, adjustable voltage regulator, monolithic silicon and agencies of the department of defense drawing approval date 99-08-09 amsc n/a revision level b size a cage code 67268 5962-99612 sheet 1 of 13 dscc form 2233 apr 97 5962-e131-11
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 2 dscc form 2234 apr 97 1. scope 1.1 scope . this drawing documents five product assurance cla sses as defined in paragraph 1.2.3 and mil-prf-38534. a choice of case outlines and lead finishes which are available and are reflected in the part or identifying number (pin). when available, a choice of radiation hardness as surance levels are reflected in the pin. 1.2 pin . the pin shall be as shown in the following example: 5962 - 99612 01 h x x federal stock class designator rha designator (see 1.2.1) device type (see 1.2.2) device class designator case outline (see 1.2.4) lead finish (see 1.2.5) \ / (see 1.2.3) \/ drawing number 1.2.1 radiation hardness assurance (rha) designator . rha marked devices shall meet the mil-prf-38534 specified rha levels and shall be marked with the appropriate rha designator. a dash (-) indicates a non-rha device. 1.2.2 device type(s) . the device type(s) identify the circuit function as follows: device type generic number 1 / circuit function 01 sdp117 positive adjustable voltage regulator 02 sdp117hv positive adjustable voltage regulator, high voltage 03 sdp137 negative adjustable voltage regulator 04 sdp137hv negative adjustable voltage regulator, high voltage 1.2.3 device class designator . this device class designator shall be a single letter identifying the product assurance level. all levels are defined by the requirements of mil-prf-38534 and require qml certification as we ll as qualification (class h, k, and e) or qml listing (class g and d). the product assurance levels are as follows: device class device performance documentation k highest reliability class available. this level is intended for use in space applications. h standard military quality class level. this level is intended for use in applications where non-space high reliability devices are required. g reduced testing version of the standard milit ary quality class. this level uses the class h screening and in-process inspections with a possible limited temperature range, manufacturer specified incoming fl ow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (group a, b, c and d). e designates devices which are based up on one of the other classes (k, h, or g) with exception(s) taken to the requirements of that class. these exception(s) must be specified in the device ac quisition document; therefor e the acquisition document should be reviewed to ensure that the exc eption(s) taken will not adversely affect system performance. d manufacturer specified quality class. q uality level is defined by the manufacturers internal, qml certified flow. this pro duct may have a limited temperature range. 1 / the sdp117, sdp117hv, sdp137, and sdp137hv are si milar to the lm117, lm117hv, lm137, and lm137hv listed on standard microc ircuit drawing 77034.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 3 dscc form 2234 apr 97 1.2.4 case outline(s) . the case outline(s) are as designated in mil-std-1835 and as follows: outline letter descriptive designator terminals package style n see figure 1 3 z-tab with nonisolated tab, (to-257z), with glass seal t see figure 1 3 flange mount with nonisolated tab, (to-257), with glass seal u see figure 1 3 flange mount with isolated tab, (to-257), with glass seal z see figure 1 3 z-tab with isolated tab, (to-257z), with glass seal 1.2.5 lead finish . the lead finish shall be as specified in mil-prf-38534. 1.3 absolute maximum ratings . 1 / input-output voltage differential: device types 01 and 03 ...................................................... 40 v dc device type 02 ....................................................................60 v dc device type 04 ....................................................................50 v dc operating junction temperature range ...................................-55 ? c to +150 ? c storage tem perature ..............................................................-65 ? c to +150 ? c lead temperature (sol dering, 10 se conds) .............................300 ? c power dissipation (p d ) ...........................................................20 w thermal resistance, junction to case ( ? jc ): cases n and t .................................................................3.5 ? c/w cases u and z .................................................................4.2 ? c/w maximum output current (i max ) ...............................................1.5 a 1.4 recommended operating conditions . output voltage range: device type 01 .................................................................1.2 to 37 v dc device type 02 .................................................................1.2 to 57 v dc device type 03 .................................................................-1.2 to -37 v dc device type 04 .................................................................-1.2 to -47 v dc input voltage range: device type 01 .................................................................4.25 v dc to 41.25 v dc device type 03 .................................................................-4.25 v dc to -41.25 v dc device type 02 .................................................................4.25 v dc to 61.25 v dc device type 04 .................................................................-4.25 v dc to -51.25 v dc ambient operating temperature range (t a ) ..........................-55 ? c to +125 ? c 2. applicable documents 2.1 government specificat ion, standards, and handbooks . the following specification, standards, and handbooks form a part of this drawing to the extent specified herein. unless otherwise specified, the issues of thes e documents are those cited in t he solicitation or contract. 1 / stresses above the absolute maximum rating may cause permanent damage to the device. extended operation at the maximum levels may degrade performance and affect reliability.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 4 dscc form 2234 apr 97 department of defe nse specifications mil-prf-38534 - hybrid microcir cuits, general specification for. department of defense standards mil-std-883 - test method standard microcircuits. mil-std-1835 - interface standard for electronic component case outlines. department of defense handbooks mil-hdbk-103 - list of standard microcircuit drawings. mil-hdbk-780 - standard microcircuit drawings. (copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the standardization document order desk, 700 robbins avenue, building 4d, philadelphia, pa 19111-5094.) 2.2 order of precedence . in the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. requirements 3.1 item requirements . the individual item performance requirements fo r device classes d, e, g, h, and k shall be in accordance with mil-prf-38534. compliance with mil-prf-38534 shall include the performance of all tests herein or as designated in the device manufacturer's quality management (qm) pl an or as designated for the applicable device class. the manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in mil-prf-38534 shall be met for the applicable device cl ass. in addition, the modification in the qm plan shall not affect the form, fit, or function of t he device for the applicable device class. 3.2 design, construction, and physical dimensions . the design, construction, and physical dimensions shall be as specified in mil-prf-38534 and herein. 3.2.1 case outline(s) . the case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 terminal connections . the terminal connections shall be as specified on figure 2. 3.3 electrical performance characteristics . unless otherwise specified herein, the electrical performance characteristics are as specified in table i and shall apply over the full specified operating temperature range. 3.4 electrical test requirements . the electrical test requirem ents shall be the subgrou ps specified in table ii. the electrical tests for each subgroup are defined in table i. 3.5 marking of device(s) . marking of device(s) shall be in accordance with mil-prf-38534. the device shall be marked with the pin listed in 1.2 herein. in addition, the manufacturer's vendor similar pin may also be marked. 3.6 data . in addition to the general performance requirements of mil-prf-38534, the manufacture r of the device described herein shall maintain the electrical test data (variables forma t) from the initial quality conf ormance inspection group a lot s ample, for each device type listed herein. also, the data should includ e a summary of all parameters manually tested, and for those which, if any, are guaranteed. this data shall be maintained under document re vision level control by the manufacturer and be made available to the preparing activity (dla land and maritime -va) upon request.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 5 dscc form 2234 apr 97 3.7 certificate of compliance . a certificate of compliance shall be required from a manufacturer in order to supply to this drawing. the certificate of compliance (original copy) submitted to dla land and maritime -va shall affirm that the manufacturer's product meets the performance r equirements of mil-prf-38534 and herein. 3.8 certificate of conformance . a certificate of conformance as required in mil-prf-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. verification 4.1 sampling and inspection . sampling and inspection procedures shall be in accordance with mil-prf-38534 or as modified in the device manufacturer's quality management (qm) plan. the modification in the qm plan shall not affect the form, fit, or function as described herein. 4.2 screening . screening shall be in accordance with mil-prf-38534. the following additional criteria shall apply: a. burn-in test, method 1015 of mil-std-883. (1) test condition a, b, c, or d. the test circuit sha ll be maintained by the manufacturer under document revision level control and shall be made available to either dla land a nd maritime -va or the acquiring activity upon request. also, the test circuit shall specify t he inputs, outputs, biases, and power diss ipation, as applicable, in accordance with the intent specified in te st method 1015 of mil-std-883. (2) t a as specified in accordance with t able i of method 1015 of mil-std-883. b. interim and final electrical test parameters shall be as spec ified in table ii herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 conformance and periodic inspections . conformance inspection (ci) and periodic inspection (pi) shall be in accordance with mil-prf-38534 and as specified herein. 4.3.1 group a inspection (ci) . group a inspection shall be in accordance with mil-prf-38534 and as follows: a. tests shall be as spec ified in table ii herein. b. subgroups 7, 8, 9, 10, and 11 shall be omitted. 4.3.2 group b inspection (pi) . group b inspection shall be in accordance with mil-prf-38534. 4.3.3 group c inspection (pi) . group c inspection shall be in accordance with mil-prf-38534 and as follows: a. end-point electrical parameters shall be as specified in table ii herein. b. steady-state life test, method 1005 of mil-std-883. (1) test condition a, b, c, or d. the test circuit sha ll be maintained by the manufacturer under document revision level control and shall be made available to either dla land a nd maritime -va or the acquiring activity upon request. also, the test circuit shall specify t he inputs, outputs, biases, and power diss ipation, as applicable, in accordance with the intent specified in method 1005 of mil-std-883. (2) t a as specified in accordance with t able i of method 1005 of mil-std-883. (3) test duration: 1,000 hours, except as permitted by method 1005 of mil-std-883. 4.3.4 group d inspection (pi) . group d inspection shall be in accordance with mil-prf-38534.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 6 dscc form 2234 apr 97 table i. electrical performance characteristics . test symbol conditions -55 ? c ? t a ? +125 ? c i l = 8 ma group a subgroups device type limits unit unless otherwise specified min max device types 01 and 02. reference voltage v ref v diff = 3.0 v 1 01,02 1.20 1.30 v v diff = 3.3 v 2,3 1.20 1.30 v diff = 40 v 1,2,3 1.20 1.30 v diff = 60 v 1,2,3 02 1.20 1.30 line regulation 1 / r line v out = v ref , 3.0 v ? v diff ? 40 v 1 01,02 ? 9 mv v out = v ref , 3.3 v ? v diff ? 40 v 2,3 ? 23 v out = v ref , 1 02 ? 5 40 v ? v diff ? 60 v 2,3 ? 10 load regulation 2 / r load v diff = 3 v, 10 ma ? i l ? 1.5 a 1 01,02 ? 15 mv v diff = 3.3 v, 10 ma ? i l ? 1.5 a 2,3 ? 15 v diff = 40v, 10 ma ? i l ? 300 ma 1 ? 15 v diff = 40 v, 10 ma ? i l ? 195 ma 2,3 ? 15 v diff = 60 v, 10 ma ? i l ? 30 ma 1,2,3 02 ? 15 thermal regulation v rth v in = 14.6 v, i l = 1.5 a, p d = 20 watts, t = 20 ms, t a = +25 ? c 1 01,02 ? 16 mv ripple rejection 3 / r n f = 120 hz, c adj = 10 ? f, v out = v ref 4,5,6 01 66 db f = 120 hz, c adj = 10 ? f, v out = v ref , i out = 100 ma 02 66 adjustment pin current i adj v diff = 3.0 v 1 01,02 100 ? a v diff = 3.3 v 2,3 100 v diff = 40 v 1,2,3 100 v diff = 60 v 1,2,3 02 100 see footnotes at end of table.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 7 dscc form 2234 apr 97 table i. electrical performance characteristics ? continued. test symbol conditions -55 ? c ? t a ? +125 ? c i l = 8 ma group a subgroups device type limits unit unless otherwise specified min max device types 01 and 02 - continued . adjustment pin current change ? i adj v diff = 3 v, 10 ma ? i l ? 1.5 a 1 01,02 ? 5 ? a v diff = 3.3 v, 10 ma ? i l ? 1.5 a 2,3 ? 5 v diff = 40 v, 10 ma ? i l ? 300 ma 1 ? 5 v diff = 40 v, 10 ma ? i l ? 195 ma 2,3 ? 5 3 v ? v diff ? 40 v 1 ? 5 3.3 v ? v diff ? 40 v 2,3 ? 5 3.3 v ? v diff ? 60 v 1,2,3 02 ? 5 minimum load current i lmin v diff = 3.0 v, v out = 1.4 v (forced) 1 01,02 5 ma v diff = 3.3 v, v out = 1.4 v (forced) 2,3 5 v diff = 40 v, v out = 1.4 v (forced) 1,2,3 5 v diff = 60 v, v out = 1.4 v (forced) 1,2,3 02 7 current limit 3 / i cl v diff = 15 v 1,2,3 01 1.50 3.50 a v diff = 40 v 1 0.18 1.5 v diff = 5 v 1,2,3 02 0.5 1.65 v diff = 40 v 1 0.15 0.65 v diff = 60 v 1 0.02 0.28 device type 03 . reference voltage v ref v diff = 3.0 v 1 03 -1.275 -1.225 v 2,3 -1.30 -1.20 v diff = 40 v 1 -1.275 -1.225 2,3 -1.30 -1.20 line regulation r line 3.0 v ? v diff ? 40 v 1 03 ? 9 mv 2,3 ? 23 see footnotes at end of table.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 8 dscc form 2234 apr 97 table i. electrical performance characteristics ? continued. test symbol conditions -55 ? c ? t a ? +125 ? c i l = 8 ma group a subgroups device type limits unit unless otherwise specified min max device type 03 - continued . load regulation 2 / r load v diff = 5 v, 8 ma ? i l ? 1.5 a 1,2,3 03 ? 25 mv v diff = 12 v, 8 ma ? i l ? 1.5 a 1 ? 25 v diff = 40v, 8 ma ? i l ? 200 ma 1 ? 25 v diff = 40 v, 8 ma ? i l ? 100 ma 2,3 ? 25 thermal regulation v rth v in = -14.6 v, i l = 1.5 a, p d = 20 watts, t = 10 ms, t a = +25 ? c 1 03 ? 5 mv ripple rejection 3 / r n f = 120 hz, c adj = 10 ? f, v out = v ref 4,5,6 03 66 db adjustment pin current i adj v diff = 3.0 v 1,2,3 03 100 ? a v diff = 40 v 1,2,3 100 adjustment pin current change ? i adj (line) 3.0 v ? v diff ? 40 v 1,2,3 03 ? 5 ? a ? i adj (load) v diff = 5.0 v, 8 ma ? i l ? 1.5 a 1,2,3 ? 5 minimum load current i lmin v diff = 3.0 v, v out = -1.4 v (forced) 1,2,3 03 3 ma v diff = 10 v, v out = -1.4 v (forced) 1,2,3 3 v diff = 40 v, v out = -1.4 v (forced) 1,2,3 5 current limit 3 / i cl v diff = 5 v 1,2,3 03 1.5 3.5 a v diff = 40 v 1 0.24 1.2 device type 04 . reference voltage v ref v diff = 3.0 v 1 04 -1.275 -1.225 v 2,3 -1.300 -1.200 v diff = 50 v 1 -1.275 -1.225 2,3 -1.300 -1.200 line regulation r line 3.0 v ? v diff ? 50 v 1 04 ? 10 mv 2,3 ? 25 see footnotes at end of table.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 9 dscc form 2234 apr 97 table i. electrical performance characteristics ? continued. test symbol conditions -55 ? c ? t a ? +125 ? c i l = 8 ma group a subgroups device type limits unit unless otherwise specified min max device type 04 - continued. load regulation 2 / r load v diff = 50 v, 8 ma ? i l ? 110 ma 1 04 ? 25 mv v diff = 5.0 v, 1 ? 25 8 ma ? i l ? 1.5 a 2,3 ? 45 thermal regulation v rth v in = -14.6 v, i l = 1.5 a, p d = 20 watts, t = 10 ms, t a = +25 ? c 1 04 ? 5 mv ripple rejection 3 / r n f = 120 hz, c adj = 10 ? f, v out = v ref 4,5,6 04 66 db adjustment pin current i adj-1 v diff = 3.0 v 1,2,3 04 100 ? a i adj-2 v diff = 40 v 1,2,3 100 i adj-3 v diff = 50 v 1,2,3 100 adjustment pin current change ? i adj v diff = 5.0 v, 8 ma ? i out ? 1.5 a 1,2,3 04 ? 5 ? a i l = 8 ma, 3.0 v ? v diff ? 50 v 1,2,3 ? 6 minimum load current i lmin v diff = 3.0 v, v out = -1.4 v (forced) 1,2,3 04 3 ma v diff = 10 v, v out = -1.4 v (forced) 1,2,3 3 v diff = 40 v, v out = -1.4 v (forced) 1,2,3 5 v diff = 50 v, v out = -1.4 v (forced) 1,2,3 5 current limit 3 / i cl v diff = 5 v 1,2,3 04 1.5 3.5 a v diff = 50 v 1 0.2 1.0 1 / to determine the line regulation limits for 3.0 v < v diff < 60 v (or 3.3 v ? ? ? v diff ? 40 v) to the limits for 40 v < v diff < 60 v. 2 / regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. changes in output voltage due to heating effects are co vered under the specification for therma l regulation. with exception of cases u and z, all output measurements are referenced to the case. measurements tak en at the output lead must be adjusted for lead resistance. 3 / if not tested, shall be guaran teed to the specified limits.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 10 dscc form 2234 apr 97 case outlines t and u. inches mm 0.005 0.13 0.010 0.25 0.020 0.51 symbol millimeters inches min max min max a 4.83 5.08 0.190 0.200 a1 0.89 1.14 0.035 0.045 a2 3.05 bsc 0.120 bsc ?b 0.64 0.89 0.025 0.035 d 16.38 16.89 0.645 0.665 d1 10.41 10.92 0.410 0.430 d3 0.00 1.65 0.000 0.065 e 2.54 bsc 0.100 bsc e 10.41 10.72 0.410 0.422 l 12.70 19.05 0.500 0.750 o 13.39 13.64 0.527 0.537 ?p 3.56 3.81 0.140 0.150 note: the u.s. government preferred sy stem of measurement is the metric si syst em. however, this item was originally designed using inch-pound units of measurement. in the event of conflict between the metr ic and inch-pound units, the inch-pound units shall take precedence. figure 1. case outline(s) .
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 11 dscc form 2234 apr 97 case outlines n and z. symbol millimeters inches min max min max a 23.11 23.37 0.910 0.920 a1 10.41 10.67 0.410 0.420 a2 6.22 6.48 0.245 0.255 a3 3.05 3.30 0.120 0.130 ?b 0.71 0.81 0.028 0.032 d 4.70 5.59 0.135 0.220 d1 2.92 3.18 0.115 0.125 d2 0.89 1.14 0.035 0.045 e 2.54 bsc 0.100 bsc l 10.41 10.67 0.410 0.420 l1 12.70 19.05 0.500 0.750 l2 6.22 6.48 0.245 0.255 l3 3.05 3.30 0.120 0.130 ?p 3.05 3.30 0.120 0.130 note: the u.s. government preferred sy stem of measurement is the metric si syst em. however, this item was originally designed using inch-pound units of measurement. in the event of conflict between the metr ic and inch-pound units, the inch-pound units shall take precedence. figure 1. case outline(s) - continued.
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 12 dscc form 2234 apr 97 device type 01, 02 03, 04 01, 02 03, 04 case outlines n and t (non-isolated tab) n and t (non-isolated tab) u and z (isolated tab) u and z (isolated tab) terminal number terminal symbol terminal symbol terminal symbol terminal symbol 1 2 3 tab adjust no connection input output adjust no connection output input adjust output input no connection adjust input output no connection figure 2. terminal connections .
standard microcircuit drawing size a 5962-99612 dla land and maritime columbus, ohio 43218-3990 revision level b sheet 13 dscc form 2234 apr 97 table ii. electrical test requirements . mil-prf-38534 test requirements subgroups (in accordance with mil-prf-38534, group a test table) interim electrical parameters 1 final electrical parameters 1*, 2, 3, 4**, 5**, 6** group a test requirements 1, 2, 3 group c end-point electrical 1 / parameters 1,2,3 end-point electrical parameters for radiation hardness assurance (rha) devices not applicable 1 / as a minimum, for all group c testing performed after (11-05-20) manufacturers shall perform subgr oups 1, 2, and 3 from the group a electrical test table (t able c-xa of mil-prf-38534). * pda applies to subgroup 1. ** subgroups 4, 5, and 6, if not tested shall be guaranteed to the limits specified in table i. 4.3.5 radiation hardness assurance (rha) inspection . rha inspection is not currently applicable to this drawing. 5. packaging 5.1 packaging requirements . the requirements for packaging shall be in accordance with mil-prf-38534. 6. notes 6.1 intended use . microcircuits conforming to this drawing are int ended for use for government microcircuit applications (original equipment), design applic ations, and logistics purposes. 6.2 replaceability . microcircuits covered by this drawing will repl ace the same generic device covered by a contractor- prepared specification or drawing. 6.3 configuration control of smd's . all proposed changes to existing smd's will be coordinated as specified in mil-prf- 38534. 6.4 record of users . military and industrial users shall inform dla lan d and maritime when a system application requires configuration control and the app licable smd. dla land and maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. users of drawings covering microelectronic devices (fsc 5962) should contact dla land and maritime - va, telephone (614) 692-0544. 6.5 comments . comments on this drawing should be directed to dl a land and maritime -va, columbus, ohio 43218-3990, or telephone (614) 692-1081. 6.6 sources of supply . sources of supply are listed in mil-hdbk-103 a nd qml-38534. the vendor s listed in mil-hdbk-103 and qml-38534 have submitted a certificat e of compliance (see 3.7 herein) to dla land and maritime - va and have agreed to this drawing.
standard microcircuit drawing bulletin date: 11-05-20 approved sources of supply for smd 5962-99612 are listed below for immediate acquisition information only and shall be added to mil-hdbk-103 and qml-38534 during th e next revisions. mil-hdbk-103 and qml-38534 will be revised to include the addition or deletion of sources. the vendors listed below have agreed to this drawing and a certificate of compliance has been subm itted to and accepted by dla land and maritime - va. this information bulletin is superseded by the next dated revision of mil-hdbk-103 and qml-38534. dla land and maritime maintains an online database of all current sources of supply at http://www.dscc.dla.mil/programs/smcr/ standard microcircuit drawing pin 1 / 2 / vendor cage number vendor similar pin 3 / 5962-9961201hna 5962-9961201hnc 5962-9961201hta 5962-9961201htc 5962-9961201hua 5962-9961201huc 5962-9961201hza 5962-9961201hzc 21845 21845 21845 21845 21845 21845 21845 21845 sdp117nhd sdp117nhg sdp117thd sdp117thg sdp117uhd sdp117uhg sdp117zhd sdp117zhg 5962-9961202hna 5962-9961202hnc 5962-9961202hta 5962-9961202htc 5962-9961202hua 5962-9961202huc 5962-9961202hza 5962-9961202hzc 21845 21845 21845 21845 21845 21845 21845 21845 sdp117hvnhd sdp117hvnhg sdp117hvthd sdp117hvthg SDP117HVUHD sdp117hvuhg sdp117hvzhd sdp117hvzhg 5962-9961203hna 5962-9961203hnc 5962-9961203hta 5962-9961203htc 5962-9961203hua 5962-9961203huc 5962-9961203hza 5962-9961203hzc 21845 21845 21845 21845 21845 21845 21845 21845 sdp137nhd sdp137nhg sdp137thd sdp137thg sdp137uhd sdp137uhg sdp137zhd sdp137zhg 5962-9961204hna 5962-9961204hnc 5962-9961204hta 5962-9961204htc 5962-9961204hua 5962-9961204huc 5962-9961204hza 5962-9961204hzc 21845 21845 21845 21845 21845 21845 21845 21845 sdp137hvnhd sdp137hvnhg sdp137hvthd sdp137hvthg sdp137hvuhd sdp137hvuhg sdp137hvzhd sdp137hvzhg 1 / the lead finish shown for each pin, representing a her metic package, is the most readily available from the manufacturer listed for that part. if the desired lead fini sh is not listed contact the vendor to determine availability. 2 / the smd device types listed above are similar to t he device types listed on smd 77034. 5962-9961201hta through 04hta are similar to 7703401ta through 04ta. 5962-9961201hua through 04hua are similar to 7703401ua through 04ua. 3 / caution . do not use this number for item acquisition. items acquired to this num ber may not satisfy the performance requirements of this drawin g . vendor cage vendor name number and address 21845 solitron devices, incorporated 3301 electronics way west palm beach, fl 33407-4697 the information contained herein is disseminated for convenience only and the government assumes no liability whatsoever for any inaccuracies in the information bulletin.

▲Up To Search▲

Price & Availability of SDP117HVUHD

	To Download SDP117HVUHD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .